www.BrainKart.

com

Reg. No.

Question Paper Code : X10407

B.E./B.Tech. DEGREE EXAMINATIONS – NOV / DEC 2020

Seventh Semester
Electrical and Electronics Engineering

EE8702 POWER SYSTEM OPERATION AND CONTROL

(Regulations 2017)
Time: 3 Hours Answer ALL Questions Max. Marks: 100
PART- A (10 x 2 = 20 Marks)

1. Why the frequency and voltage are to be regulated in power system?

2. What happens to frequency if the load on the generator increases?

3. What is the purpose of secondary ALFC?

4. Write the tie line power deviation equation in terms of frequency.

5. What is booster transformer? Where it is used?

6. Compare series and shunt capacitors.

7. What are cold reserves and hot reserves?

8. What are all the points to be noted for an economic load dispatch including transmission
losses?

9. Draw the block diagram of PMU with details.

10. What are the different operating states of a power system?

PART- B (5 x 13 = 65 Marks)

11. a) Explain the basic P-f and Q-V control loops in power system with relevant block
diagram. (13)

OR

https://play.google.com/store/apps/details?id=info.therithal.brainkart.annauniversitynotes
 www.BrainKart.com
b) A generation station of 1MW supplied a region which has the following demands:

Neglect transmission line losses and find the following: i) Plot the daily load curve
and the load duration curve. ii) Find the load factor, the reserve capacity, plant
capacity factor, plant use factor, the hours that the plant has been off and
utilization factor. (13)

12. a) Derive the transfer function of an uncontrolled load frequency control of a single
area system and derive the expression for static error following a step load change.
(13)

OR

b) A two-area power system connected by a tie-line has the following parameters:

Parameters/Area Area 1 Area 2

Turbine output Power (MW) 4000 2000
Nominal Frequency (Hz) 50 50
Speed regulation 4% 5%
Power system Gain ( kp) 50 125
Governor Time Constant 0.2 0.1
Turbine Time Constant 0.3 0.25

A load change of 80 MW occurs in area 1. Determine the steady state frequency

and the change in the tie-line flow.
(13)

13. a) The load at receiving end of a 3phase overhead line is 30 MW, 0.8 pf lag at the
line voltage of 66kV. A synchronous compensator is situated at sending end and
the voltage at both ends of the line is maintained at 66kV. Calculate the MVAR of
compensator. The line has a resistance and reactance of 6Ω/ph, 24 Ω/ph,
respectively. (13)

OR

b) Two sub-station are connected by two lines in parallel with negligible impedance,
but each containing a tap-changing transformer of reactance 0.22pu on the basis of
its rating of 200 MVA. Find the net absorption of reactive power when the
transformer taps are set to 1:1.08, and 1:0.95 respectively. Assume pu voltages to
be equal at the two ends. (13)

https://play.google.com/store/apps/details?id=info.therithal.brainkart.annauniversitynotes
 www.BrainKart.com

14. a) A power plant has two units with the following cost characteristics:
C1 = 0.6 P1 2 + 200 P1 + 2000 Rs / hour
C2 = 1.2 P2 2 + 150 P2 + 2500 Rs / hour
where P1 and P2 are the generating powers in MW. The daily load cycle is as
follows:
6:00 A.M. to 6:00 P.M. 150 MW
6:00 P.M. to 6:00 A.M. 50 MW
The cost of taking either unit off the line and returning to service after 12 hours is
Rs 5000. Considering 24 hour period from 6:00 A.M. one morning to 6:00 A.M.
the next morning. i) Compute the economic schedule for the peak load and off
peak load conditions, ii) Calculate the optimum operating cost per day.
(13)

OR

b) Consider the following three units:

IC1 = 7.92 + 0.003124 PG1
IC2 = 7.85 + 0.00388 PG2
IC3 = 7.97 + 0.00964 PG3;
PD = 850 MW ; PG1 = 392.2 MW; PG2 = 334.6 MW; PG3 = 122.2 MW.
Determine the optimum schedule if the load is increased to 900 MW by using
Participation Factor method. (13)

15. a) With the help of flowchart explain briefly how the system states are continuously
monitored and controlled. (13)

OR

b) Explain the hardware components and functional aspects of SCADA system using
a fundamental block diagram. (13)

PART- C (1 x 15 = 15 Marks)

16. a) There are three thermal generating units which can be committed to take the
system load. The fuel cost data and generation operating unit data are given below:
F1 = 392.7 + 5.544 P1 + 0.001093 P12
F2 = 217 + 5.495 P2 + 0.001358 P22
F3 = 65.5 + 6.695 P3 + 0.004049 P32
P1, P2, P3 in MW Generation limits:
150 ≤ P1 ≤ 600 MW;
100 ≤ P2 ≤ 400 MW;
50 ≤ P3≤ 200 MW
There are no other constraints on system operation. Obtain an optimum unit
commitment table. Adopt Brute force enumeration technique. Show the details of
economic schedule and the component and total costs of operation for each

https://play.google.com/store/apps/details?id=info.therithal.brainkart.annauniversitynotes
 www.BrainKart.com
feasible combination of units for the load level of 900 MW.
(15)

OR

b) The fuel input data for a three plant system are:

f1 = 0.01 P1 2 + 1.7 P1 + 300 Millions of BTU / hour
f2 = 0.02 P2 2 + 2.4 P2 + 400 Millions of BTU / hour
f3 = 0.02 P3 2 + 1.125 P3 + 275 Millions of BTU / hour
where Pi’s are the generation powers in MW. The fuel cost of the plants are Rs 50,
Rs 30 and Rs 40 per Million of BTU for the plants 1,2 and 3 respectively. The loss
coefficient matrix expressed in MW-1 is given by

The load on the system is 60 MW. Compute the power dispatch for λ = 120 Rs /
MWh. Calculate the transmission loss. Also determine the power dispatch with the
revised value of λ taking 10 % change in its value. Estimate the next new value of
λ. (15)

__________________

https://play.google.com/store/apps/details?id=info.therithal.brainkart.annauniversitynotes
 Click on Subject/Paper under Semester to enter.
Probability and Environmental Sciences
Professional English complex function - and Sustainability -
Professional English - - II - HS3252 MA3303 GE3451
I - HS3152
Statistics and Electromagnetic Transmission and
Matrices and Calculus Numerical Methods - Theory - EE3301 Distribution - EE3401

4th Semester
3rd Semester

- MA3151 MA3251
1st Semester

2nd Semester

Digital Logic Circuits - Linear Integrated

Engineering Physics - Engineering Graphics EE3302 Circuits - EE3402
PH3151 - GE3251
Measurements and
Electron Devices and Instrumentation -
Engineering Chemistry Physics for Electrical Circuits - EC3301 EE3403
- CY3151 Engg - PH3202
Microprocessor and
Electrical Machines I - Microcontroller -
Basic Civil and
EE3303 EE3404
Problem Solving and Mechanical Engg -
Python Programming - BE3255
C Programming and Electrical Machines II
GE3151
Electric Circuit Data Structures - - EE3405
Analysis - EE3251 CS3353

Power System Analysis

High Voltage
- EE3501
Engineering - EE3701
Protection and
Switchgear - EE3601
Power Electronics - Human Values and
5th Semester

EE3591 Ethics - GE3791

8th Semester
7th Semester
6th Semester

Power System
Operation and Control
Control Systems - - EE3602 Open Elective 2
EE3503 Project Work /
Open Elective-1
Open Elective 3 Intership
Elective 1 Elective-4
Open Elective 4
Elective 2 Elective-5
Elective 7
Elective 3 Elective-6
Management Elective
 All EEE Engg Subjects - [ B.E., M.E., ] (Click on Subjects to enter)
Circuit Theory Digital Logic Circuits Electromagnetic Theory
Environmental Science and Linear Integrated Circuits Discrete Time Systems and
Engineering and Applications Signal Processing
Electronic Devices and Electrical Machines I Electrical Machines II
Circuits
Power Plant Engineering Special Electrical Machines Transmission and Distribution
Power System Analysis Control Systems Power Electronics
Power System Operation Measurements and Design of Electrical Machines
and Control Instrumentation
Communication Engineering Solid State Drives Embedded Systems
Power Quality High Voltage Engineering Protection and Switchgear
Flexible AC Transmission Microprocessors and Electric Energy Generation,
Systems Microcontrollers Utilization and Conservation
Professional Ethics in Physics for Electronics Basic Civil and Mechanical
Engineering Engineering Engineering
Transforms and Partial Environmental Science and Problem Solving and Python
Differential Equations Engineering Programming
Engineering Physics Engineering Chemistry Numerical Methods
Engineering Graphics Technical English Object Oriented Programming
Principles of Management Total Quality Management