ESP32-CAM Web Controlled Car

By BeepBoopPrints in Workshop3D Printing

Introduction: ESP32-CAM Web Controlled Car

A simple web controlled ESP32 robot with a camera. Powered by a LiPo battery and uses 4 n20
motors.
Supplies
1x ESP32-CAM microcontroller

4x N20 Motor (60RPM) (Aliexpress)

2x MX 1508 Brushed DC motor driver (Also sometimes reffered to as mini L298 drivers) (Amazon
UK) (AliExpress)

1x 7.4v Lipo battery (Amazon UK)

1x JST connector (Amazon UK)

1x Mini3060 DC-DC step down module (Amazon UK)(AliExpress)

1x 160 degree OVO2640 module 75mm in length. (Amazon UK)

1x 60x80mm prototype / pef board (I used double sided but single should work) (AliExpress)

A 40 pin strip of male board headers.

A selection of Female jumper wires. (The kits that provide 40 of each kind should suffice as some
will be cut in half)

2x 8 pin female board headers (For esp32 to be slotted into)

2 pin rocker switch (Inside sizing should be approx 18.6mm x 11.8mm, you can file or sand the
opening bigger or adjust the print if a larger hole is needed for your switch) (Amazon UK)

12x M3x8 bolts

4x M2x6 bolts (2 will be enough if you dont have 4)

Jumper wires with exposed ends for creating the connections on the power distribution board

Code can be found on GITHUB

(Suggested tools but not needed)

Solder wick for fixing any solder related issues

Estimated cost to build (April 2025) £35-45/ €40-50/ $50-60 USD (however could be more due to
tarrifs), however you may need to buy certain parts in sets of 2, 5, 10 etc meaning it may cost more
but you have spares or maybe even enough parts to build 2! You may find the same parts cheaper
elsewhere.
Step 1: 3D Printed Components

Print the Wheels, bottom, mid, top,shell sections in PLA. This will take approx 7-8 hours total but
could take longer depending on your printer. I recommend printing the bottom section, wheels, tires
and the N20 motor housings to allow you to get started on the project a little faster whilst the shell
and upper sections print.

Print the Tires in a 95A TPU (ensure you print at the correct temperature to reduce any
imperfections)
Step 2: Soldering Motor Connections

Your motors may come with pre soldered wires however I found they can be weak and snap off
with almost no effort. I cut one of the Female-Female jumper cables in half, stripping the non
connector end by about 5-10mm and soldering that to the motor.

Be careful when soldering to the motor pins, don't solder it too hot or you may damage the motor
housing and connector points. Do this for all 4 motors. I found it best soldering them with black and
red cables and soldering them all the same orientation (you can tell by the cogs on the motor).
Step 3: Attaching Motors + Wheels

On the bottom shell you will see 8 screw holes in the middle, this is where the 4 motor housings
screw into place.

Insert each motor into the n20 motor housing rod end first then the back should snap fit into place.

For the 4 wheels overlap a tire over a wheel, it should be tight and almost seem like it wont fit but
the 95a has just enough stretch to allow it to be put onto the wheel. This is done to ensure it stays
put. Now connect each wheel to an N20 motor. if you look on the wheel on one of the 4 sections it
has a slight bump this is the side the flat part of the N20 shaft should face and push the wheel onto
the motor. Depending on how yours has printed some may go on with next to no force but some
may need more encouragement. if it slides on and off too easy then you may need to check your
print settings.

Now screw in each housing with the wheels attached to the base. The housings should be on the
same side as the screw pillars for the mid section.
Step 4: Soldering Headers to the Motor Drivers

You can directly solder wires between the motors and drivers but it can lead to issues when trying
to troubleshoot problems. I found it way easier just soldering some headers so I could connect or
disconnect jumpers to help find any issues. Solder all 9 headers. You should be able to do them in
a set of 2 for each 2 pin hole. Again don't solder too hot or you may melt the plastic holding the pins
in place.
Step 5: Soldering the Power Distribution Board

Pictured is how the connections need to go on the power distribution board. My soldering is not the
best but should give you a rough idea of how it should go together. The lipo needs to power the 2
power connections to the motor drivers, and a connection to the DC step-down converter.The other
side of the converter needs to connect to 5V and GND on the ESP32. Then 8 headers (2 rows of 4)
connected to the GPIO.
Step 6: Connecting Everything Up
Once the midsection has printed you can feed the cables from each motor up and through the
small holes provided, insert the motor drivers as shown and place the battery in the section in the
middle.. Ensure you have also screwed down the midsection. The screw down the power board
with the connection points facing up. Connect power and ground to each motor controller, then
each of the controlling cables.

Step 7: Programming the ESP32 CAM

Upload the code to the board but insert your SSID name and password to the relevant sections.
Once its loaded, use the serial monitor on 115200 baud to see what IP the device will use. (This
may change if not assigned a static IP in your router however you can also check the IP on your
router by looking at your connected devices)

Code can be found on GITHUB

Step 8: Testing It Works
Before cutting up the battery connector in the next step connect the battery to the power board with
the intact cable and test the esp32 powers up.

Step 9: Adding the Power Button and Closing Up the Shell

Step 10: Controlling the Bot

Turn on the power switch, and on your PC, Mac or Phone connect to the device in your browser via
the IP address as mentioned in step 7. (Your Local IP of the bot may differ from mine). You should
see a camera feed and 4 buttons to control. On mobile the buttons can sometimes get stuck so it
often controls better on a desktop / laptop browser. That should be it, If you find your motors don't
go the right way then you may need to check your wiring and re organise it until the motors all work
correctly.

For charging the battery I havent incorporated a lipo charger into this project so you will need to
unscrew the top, disconnect the battery and connect it to a charger (usually provided with the
batteries). However it could be an upgrade point for you to incorperate yourself!
Step 11: Future Version
As you will notice in the shell just below the camera is a space big enough for a 15mm speaker and
on the midsection frame there is space for a MAX98357A to be connected. In the future I plan to
update the project to incorporate this however feel free to add this yourself! There should be just
enough pins left on the esp32 for you to add it. Just adapt the power distribution board for the
connections from the ESP32-CAM.

I plan to release a version 2 of this bot later in the year which will hopefully include the audio and
possibly even microphone capability so it could be used as a remote control security camera.