Cambridge (CIE) O Level Your notes

Physics
4.4 Practical Electricity
Contents
Electrical Safety
Electrical Energy
Electrical Power

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 1
 Electrical Safety
Your notes
Uses of Elelctricity
Electricity is used in most aspects of modern day living
As a result, the demand for electricity as a global society is immense
Some common uses of electricity are:
Heating
Such as plug-in heaters, electric ovens and hobs, even gas boilers use
electricity to power them
Lighting
Such as street lights, shop signs, ceiling and wall lighting, and plug-in lamps
Battery charging
For devices such as mobile phones, tablets and laptops
Powering motors
Motors are used in machines like washing machines, tumble dryers & hair dryers
Electronic systems
Such as TVs and games consoles

Electrical Hazards
Mains electricity is potentially lethal – potential differences as small as 50 volts can pose
a serious hazard to individuals

Risk of Electrocution Hazzard Symbol

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 2
 Your notes

The risk of electrocution is indicated by hazard signs but other risks which would not be
signposted are listed below

Common hazards include:

Damaged Insulation – If someone touches an exposed piece of wire, they could be
subjected to a lethal shock
Overheating of cables – Passing too much current through too small a wire (or
leaving a long length of wire tightly coiled) can lead to the wire overheating. This
could cause a fire or melt the insulations, exposing live wires
Damp conditions – If moisture comes into contact with live wires, the moisture
could conduct electricity either causing a short circuit within a device (which could
cause a fire) or posing an electrocution risk
Excess current from overloading of plugs, extension leads, single and multiple
sockets when using a mains supply - If plugs or sockets become overloaded due
to plugging in too many components the heat created can cause fires

Overloaded Extension Lead

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 3
 Your notes

Overloading extension cables can lead to overheating and in some cases, fires

Mains Circuits
Mains Electricity
Mains electricity is the electricity generated by power stations and transported around
the country through the National Grid
Everyone connects to the mains when plugging in an appliance such as a phone
charger or kettle
Mains electricity is an alternating current (a.c.) supply
In the UK, the domestic electricity supply has a frequency of 50 Hz and a potential
difference of about 230 V
A frequency of 50 Hz means the direction of the current changes back and forth 50
times every second
Mains electricity, being an alternating current, does not have positive and negative sides
to the power source
The equivalent to positive and negative are called live and neutral and these form
either end of the electrical circuit

Three-pin Plug & Earth Connection

UK Plug Socket & Plug

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 4
 Your notes

The plug socket and inside of a three-pin plug showing the three wires and their
connections. The live and neutral wires deliver the electricity to the device. The Earth wire
is for safety
In order to protect the user or the device, there are several safety features built into
domestic appliances, including:
Double insulation
Earthing
Fuses
Circuit breakers

Insulation & Double Insulation

The conducting part of a wire is usually made of copper or some other metal
If this comes into contact with a person, this poses a risk of electrocution

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 5
 For this reason, wires are covered with an insulating material, such as rubber
Insulated Wires
Your notes

The conducting part of a wire is covered in an insulating material for safety

Some appliances do not have metal cases and so there is no risk of them becoming
electrified
Such appliances are said to be double insulated, as they have two layers of insulation:
Insulation around the wires themselves
A non-metallic case that acts as a second layer of insulation
Double insulated appliances do not require an earth wire or have been designed so that
the earth wire cannot touch the metal casing

Earthing
Many electrical appliances have metal cases
This poses a potential safety hazard:
If a live wire (inside the appliance) came into contact with the case, the case would
become electrified and anyone who touched it would risk being electrocuted
The earth wire is an additional safety wire that can reduce this risk
If this happens:
The earth wire provides a low resistance path to the earth

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 6
 It causes a surge of current in the earth wire and hence also in the live wire
The high current through the fuse causes it to melt and break Your notes
This cuts off the supply of electricity to the appliance, making it safe
Fuses & Trip Switches
A fuse is a safety device designed to cut off the flow of electricity to an appliance if the
current becomes too large (due to a fault or a surge)

Circuit Symbol for a Fuse

The circuit symbol for a fuse - take care not to confuse this with a resistor. The wire runs
straight through the rectangle representing the fuse wire
Fuses usually consist of a glass cylinder which contains a thin metal wire.
If the current in the wire becomes too large:
The wire heats up and melts
This causes the wire to break, breaking the circuit and stopping the current
A trip switch, found in the Consumer Box (where the electricity enters the building) does
the same job as a fuse
When the current is too high the switch 'trips' (automatically flicks to the off position)
This stops current flowing in that circuit

Choosing Which Fuse to Use

Fuses come in a variety of sizes (typically 3A, 5A and 13A) - in order to select the right
fuse for the job, you need to know how much current an appliance needs
If you know the power of the appliance (along with mains voltage), the current can be
calculated using the equation:

power
current = potential difference
P
I =V
The fuse should always have a current rating that is higher than the current needed by the
appliance, without being too high - always choose the next size up

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 7
Example:
Suppose an appliance uses 3.1 amps Your notes
A 3 amp use would be too small - the fuse would blow as soon as the appliance was
switched on
A 13 amp fuse would be too large - it would allow an extra 10 amps to pass through
the appliance before it finally blew
A 5 amp fuse would be an appropriate choice, as it is the next size up

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 8
 Electrical Energy
Your notes
Electrical Energy Equation
Everyday appliances transfer energy from the mains supply to the appliance
For example, a heater will transfer energy electrically to the thermal store of the
heating element
The amount of energy an appliance transfers depends on:
The time the appliance is switched on for
The power of the appliance
A 1 kW iron uses the same amount of energy in 1 hour as a 2 kW iron would use in 30
minutes
A 100 W heater uses the same amount of energy in 30 hours as a 3000 W heater does in 1
hour

Calculating Electrical Energy

To calculate electrical energy use the equation

E = VIt
Where:
E = energy (joules, J)
V = voltage (volts, V)
I = current (amps, A)
t = time (seconds, s)

Examiner Tips and Tricks

Remember that kilo (k) means 1000, so 1 kW = 1000 W

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 9
 Electrical Power
Your notes
Electrical Power Equation
In mechanics, power P is defined as the rate of doing work
The potential difference is the work done per unit charge
Current is the rate of flow of charge
Therefore, the electrical power is defined as the rate of change of work done:

E W
P = t
= t
Where:
P = power in watts (W)
E = energy in joules (J)
t = time in seconds (s)
W = work done in (J)
The work done is the energy transferred so the power is the energy transferred per
second in an electrical component
The power dissipated (produced) by an electrical device can also be written as

P = IV
Where:
P = power in watts (W)
I = current in amps (A)
V = potential difference in volts (V)
Using Ohm's Law V = IR to rearrange for either V or I and substituting into the power
equation, means power can be written in terms of resistance R

P = I2R
V2
P = R
Where:
P = power in watts (W)
I = current in amps (A)
R = resistance in ohms (Ω)

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 10
 V = potential difference in volts (V)
This means for a given resistor if the current or voltage doubles the power will be four
times as great. Your notes
Which equation to use will depend on whether the value of current or voltage has
been given in the question
Rearranging the energy and power equation, the energy can be written as:

E = VIt
Where:
E = energy transferred in joules (J)
V = potential difference in volts (V)
I = current in amps (A)
t = time in seconds (s)

Worked Example
Two lamps are connected in series to a 150 V power supply.

Which statement most accurately describes what happens?

A. Both lamps light normally
B. The 15 V lamp blows
C. Only the 41 W lamp lights
D. Both lamps light at less than their normal brightness
Answer: A
Calculate the current needed for both lamps to operate

P = IV

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 11
 P
I =V
Your notes
For the 41 W lamp:
41
I = 135 = 0 . 3 A
For the 4.5 W lamp
4.5
I = 15
= 0.3 A
For both lamps to operate at their normal brightness, a current of 0.3 A is required
Since the lamps are connected in series, the same current would flow through
both
Therefore, the lamps will light at their normal brightness
This is option A

Examiner Tips and Tricks

You can use the mnemonic “Twinkle Twinkle Little Star, Power equals I squared R” to
remember whether to multiply or divide by resistance in the power equations.
When doing calculations involving electrical power, remember the unit is Watts W,
therefore, you should always make sure that the time is in seconds

Measuring Energy Usage

The Kilowatt Hour (kWh)
Energy usage in homes and businesses is calculated and compared using the kilowatt
hour
The kilowatt hour is defined as:
A unit of energy equivalent to one kilowatt of power expended for one hour

Appliances are given power ratings, which tell consumers:

The amount of energy transferred (by electrical work) to the device every second

Power Rating for a Kettle

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 12
 Your notes

This kettle uses between 2500 and 3000 W of electrical energy

This energy is commonly measured in kilowatt-hour (kW h), which is then used to
calculate the cost of energy used

Calculating with kWh

The kilowatt hour can also be defined using an equation:

E = Pt
Where
E = energy (kWh)
P = power (kW)
t = time (h)
This equation is unusual because S.I. unit are not used, both energy and power
are × 103, and time is in hours, not seconds
Since the usual unit of energy is joules (J), this is the 1 W in 1 s
Therefore:

1 kW h = 1000 W × 3600 s = 3 . 6 × 106 J

Since 1 kW = 1000 W and 1 h = 3600 s

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 13
To convert between Joules and kW h:
kW h × 3 . 6 × 106 = J
( )

Your notes
J ÷ 3 . 6 × 106 = kW h
( )

The kW h is a large unit of energy, and mostly used for energy in homes, businesses,
factories and so on

Worked Example
A cooker transfers 1.2 × 109 J of electrical energy to heat up a meal.
Calculate the cost of cooking the meal if 1 kW h costs 14.2p
Answer:
Step 1: Convert from J to kW h

( 1.2 × 109 ÷ 3 . 6 × 106 = 333 . 333 kW h

) ( )

Step 2: Calculate the price

= 14. 2 p
1 kW h
333 . 333 × 14. 2 = 4733 p = £ 47. 33

© 2025 Save My Exams, Ltd. Get more and ace your exams at savemyexams.com 14