0% found this document useful (0 votes)
8 views9 pages

W43023

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
8 views9 pages

W43023

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

WAFER WIN W43023

4-Channel BTL Motor Driver for CD-ROM

Features Description
˙W43023 is a 4 channel driver for optical disc The W43023 is a 4-channel BTL driver IC for
motor driver. Dual channel current feedback driving the motors and actuators in products
type drivers are built in, in addition to dual such as CD-ROM/DVD-ROM/DVD-Player
channel motor driver. drives. Two of the channels use current feedback
˙Separating Vcc into Pre-power of sled motor, to minimize the current phase shift caused by the
Power of loading motor and Power of actuator, influence of load inductance.
can make batter power efficiency, by low Applications
supply voltage drive. CD-ROM drives, DVD drives, DVD-ROM
˙Stand-by mode built in. drives.
˙Thermal shutdown circuit on chip.

Block Diagram

* All specs and applications shown above subject to change without prior notice.

Page 1 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

Pin Descriptions
Pin No. Pin name Function
1 VINFC Focus drive input
2 CFCerr1 For connection of capacitor for the error amp filter
3 CFCerr2 For connection of capacitor for the error amp filter
4 VINSL + Op-amp input (+) for the sled driver
5 VINSL - Op-amp input (-) for the sled driver
6 VOSL Op-amp output for the sled driver
7 VNFFC Focus driver feedback pin
8 Vcc Vcc
9 PVcc1 Power Vcc for sled driver block
10 PGND Ground for Sled driver block
11 VOSL - sled driver output (-)
12 VOSL + sled driver output (+)
13 VOFC - Focus driver output (-)
14 VOFC + Focus driver output (+)
15 VOTK + Tracking driver output (+)
16 VOTK - Tracking driver output (-)
17 VOLD + Loading driver output (+)
18 VOLD - Loading driver output (-)
19 PGND Ground for Actuator driver block
20 VNFTK Tracking driver feedback pin
21 PVcc2 Power Vcc for Actuator driver block
22 GND Ground
23 VINTK Loading driver input
24 CTKerr2 For connection of capacitor for the error amp filter
25 CTKerr1 For connection of capacitor for the error amp filter
26 VINTK Tracking driver input
27 BIAS Bias input
28 MUTE Mute control
Notes: The indicated polarities for the output pins are for when all inputs are (+).
The output H bridge supply pins are PVcc1 for the loading channel, PVcc2 for the focus, tracking
channels, and Vcc for the pre-block and sled channel. Always ensure that Vcc≧PVcc1,2.
PinOut

W43023

* All specs and applications shown above subject to change without prior notice.

Page 2 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

Absolute maximum ratings (Ta = 25oC)


Parameter Symbol Limits unit
Power supply voltage VCC、PVcc1,2 13.5 V
Power dissipation Pd 1.7* W
o
Operating temperature Topr -35~+85 C
o
Storage temperature Tstg -55~+150 C
﹡Reduce by 13.6 mW for each increase in Ta of 1oC over 25oC.
When mounted on a 70mm × 70mm × 1.6 mm glass epoxy board.

Recommended operating conditions (Ta = 25oC)


Parameter Symbol Limits unit
Power supply voltage Vcc 4.5~13.2 V
PVcc1 4.5~Vcc V
PVcc2 4.5~Vcc V

Electrical characteristics
(unless otherwise noted, Ta = 25oC, VCC = PVCC1 =12V, PVCC2 =5V, VBIAS=2.5V, RL1= RL2=8Ω, RL3= RL4=15Ω)
Parameter Symbol Min. Typ. Max. Unit Conditions
Quiescent current ICC - 18 27 mA
Stand-by quiescent current IST - - 0.5 mA
Voltage for Stand-by ON VSTON 0 - 0.5 V
Voltage for Stand-by OFF VSTOFF 2.0 - - V
<Actuator driver>
Output offset current IO1,2 -6 - 6 mA
Maximum output amplitude VO1,2 3.6 4.0 - V VIN = VBIAS ± 1.5V
Trans conductance Gm 1.3 1.5 1.7 A/V VIN = VBIAS ± 0.2V
<Sled motor driver/Pre OP-amp>
Common mode input range VICM -0.3 - 11.0 V VBIAS =6 V
VICM -0.3 - 4.0 V Vcc=PVcc1=5V
Input bias current IBOP - 30 300 nA
Low level output voltage VOLOP - 0.1 0.3 V
Output source current ISO 0.3 0.5 - mA
Output sink current ISI 1 - - mA
<Sled motor driver>
Output offset voltage VOFFSL -100 0 100 mV
Maximum output voltage VO3 7.5 9.0 - V VIN = VBIAS ± 1.5V
Closed loop voltage gain GVSL 18.0 20.0 22.0 dB VIN = VBIAS ± 0.2V
<Loading motor driver>
Output offset voltage VOFFLD -50 0 50 mV
Maximum output voltage VO4-1 7.5 9.0 - V VIN = VBIAS ± 1.5V
Maximum output voltage VO4-2 3.6 4.0 - V VIN = VBIAS ± 1.5V
Vcc=PVcc1=5V
Closed loop voltage gain GVLD 13.5 15.5 17.5 dB VIN = BIAS ± 0.2V
Gain error by polarity ΔGVLD 0 1 2 dB VIN = BIAS ± 0.2V
*This product is not designed for protection against radioactive rays.

* All specs and applications shown above subject to change without prior notice.

Page 3 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

Typical Curve

* All specs and applications shown above subject to change without prior notice.

Page 4 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

* All specs and applications shown above subject to change without prior notice.

Page 5 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

* All specs and applications shown above subject to change without prior notice.

Page 6 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

Test Circuit

W43023

W43023

* All specs and applications shown above subject to change without prior notice.

Page 7 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

Application example

W43023

W43023

* All specs and applications shown above subject to change without prior notice.

Page 8 of 9 Rev 1.0 Sep. 13,2005


WAFER WIN W43023
4-Channel BTL Motor Driver for CD-ROM

Operation notes
(1) Thermal-shut-down circuit built in. In case (approximatelv 0.1μF).
IC chip temperature rise to 175 ℃ (typ.), (5) Heat dissipation fins are attached to the GND
thermal-shut-down circuit operates and on the inside of the package. Make sure to
output current muted. Next time IC chip connect these to the external GND.
temperature falls below 150 ℃ (typ.), the
driver blocks start. < Supplement >
(2) In case stand-by-pin voltage under 0.5V or Current-feedback driver
opened, quiescent current is muted. stand-by- Trans conductance (output current/input voltage)
pin voltage should be over 2.0V for normal is show as follows.
application.
(3) Bias-pin (pin 27) should be pulled up more 1
than 1.2V. In case bias-pin voltage is pulled gm = ( A/V )
Rd + RWIRE
down under 0.9V (typ.), output current is RWIRE = 0.15Ω (± 0.05Ω) Au wire
muted.
(4) Insert the by-pass capacitor between Vcc-pin
and GND-pin of IC as possible as near

Package Outlines (units:mm): HSOP-28

* All specs and applications shown above subject to change without prior notice.

Page 9 of 9 Rev 1.0 Sep. 13,2005

You might also like