Scribd
Upload
6 views4 pages

ASSET_DOC_2331294

The HLD Plastic Anchor is an economical solution for drywall applications, featuring a simple setting process and various anchor sizes (HLD 2, HLD 3, HLD 4) with specific loading data for different base materials. The datasheet provides characteristic resistance, design resistance, and recommended loads based on the type of gypsum board, hollow clay brick, and concrete. Installation guidelines include temperature ranges, drill bit specifications, and required tools for proper setup.

Uploaded by

rania
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
6 views4 pages

ASSET_DOC_2331294

The HLD Plastic Anchor is an economical solution for drywall applications, featuring a simple setting process and various anchor sizes (HLD 2, HLD 3, HLD 4) with specific loading data for different base materials. The datasheet provides characteristic resistance, design resistance, and recommended loads based on the type of gypsum board, hollow clay brick, and concrete. Installation guidelines include temperature ranges, drill bit specifications, and required tools for proper setup.

Uploaded by

rania
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

HLD

PLASTIC ANCHOR
Technical Datasheet
Update: Jan-23
HLD Plastic anchors
Economical plastic anchor for drywall
Anchor version Benefits
- Plastic undercut anchor
- Simple setting
HLD - Drywall application
(d10)

Base material

Drywall

Basic loading data

All data in this section applies to:


- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Base material as specified in the table
- Load data given in the tables is independent of load direction

Characteristic resistance
Anchor size HLD 2 HLD 3 HLD 4
Anchoring principle a)
Gypsum board
B FRk [kN] 0,4 0,4 0,4
Thickness 12,5mm
Fibre reinforced gypsum board
A FRk [kN] 0,3 - -
Thickness 12,5mm
Fibre reinforced gypsum board
A FRk [kN] - 0,6 -
Thickness 2x12,5mm
Hollow clay brick A/B FRk [kN] 0,75 0,75
Concrete ≥ C16/20 C FRk [kN] 1,25 2 2,5
a) See setting details

Design resistance
Anchor size HLD 2 HLD 3 HLD 4
Anchoring principle a)

Gypsum board
B FRd [kN] 0,11 0,11 0,11
Thickness 12,5mm
Fibre reinforced gypsum board
A FRd [kN] 0,08 - -
Thickness 12,5mm
Fibre reinforced gypsum board
A FRd [kN] - 0,17 -
Thickness 2x12,5mm
Hollow clay brick A/B FRd [kN] 0,21 0,21 -
Concrete ≥ C16/20 C FRd [kN] 0,35 0,56 0,70
a) See setting detail
Recommended loads b)
Anchor size HLD 2 HLD 3 HLD 4
Anchoring principle a)
Gypsum board
B FRec [kN] 0,08 0,08 0,08
Thickness 12,5mm
Fibre reinforced gypsum board
A FRec [kN] 0,06 - -
Thickness 12,5mm
Fibre reinforced gypsum board
A FRec [kN] - 0,12 -
Thickness 2x12,5mm
Hollow clay brick A/B FRec [kN] 0,15 0,15
Concrete ≥ C16/20 C FRec [kN] 0,25 0,4 0,5
a) See setting details
b) With overall global safety factor  = 5 to the characteristic loads and a partial safety factor of  = 1,4 to the design value.

Materials

Material quality
Part Material
Sleeve Polyamide PA 6

Setting information

Installation temperature
-10°C to + 40°C

Service temperature range


Hilti HLD universal anchor may be applied in the temperature range given below.

Base material Max. long term base Max. short term base
Temperature range
temperature material temperature material temperature
Temperature range -40 °C to +80 °C +50 °C +80 °C

Max short term base material temperature


Short-term elevated base material temperatures are those that occur over brief intervals, e.g. as a result of diurnal
cycling.
Max long term base material temperature
Long-term elevated base material temperatures are roughly constant over significant periods of time.
Setting details
Anchor size HLD 2 HLD 3 HLD 4
Nominal diameter of drill bit do [mm] 10
Depth of drill hole (only anchoring principle C) h1 ≥ [mm] 50 56 66
(anchoring principle A/B) ls [mm] 33 + tfix 40 + tfix 49 + tfix
Screw length
(anchoring principle C) ls [mm] 40 + tfix 46 + tfix 56 + tfix
(anchoring principle A/B) ds [mm] 4-5
Screw diameter
(anchoring principle C) ds [mm] 5-6
(anchoring principle A) h [mm] 4 – 12 15 – 19 24 - 28
Wall / panel thickness (anchoring principle B) h [mm] 12 – 16 19 – 25 28 - 32
(anchoring principle C) h [mm] 35 42 50

Installation equipment
Anchor size HLD 2 HLD 3 HLD 4
Rotary hammer TE 2- TE16
Other tools Screwdriver

Setting instruction

*For detailed information on installation see instruction for use given with the package of the product.
Setting instruction
1. Drill hole with drill bit 2. Install anchor

3. Install anchor 4. Drive in the screw

You might also like