1.

Load cases
Name Description Action type Load group Direction Master load
case
Spec Load type
LC1 Self weight Permanent LG1 -Z
Self weight
LC2 Postojan tovar Permanent LG1
Standard
LC3 Sneg Variable LG2 None
Snow Static
3DWind1 0, + CPE, + CPI Variable LG3 None
Static wind Static
3DWind2 0, + CPE, - CPI Variable LG3 None
Static wind Static
3DWind3 0, - CPE, + CPI Variable LG3 None
Static wind Static
3DWind4 0, - CPE, - CPI Variable LG3 None
Static wind Static
3DWind5 90, + CPE, + CPI Variable LG3 None
Static wind Static
3DWind6 90, + CPE, - CPI Variable LG3 None
Static wind Static
3DWind7 90, - CPE, + CPI Variable LG3 None
Static wind Static
3DWind8 90, - CPE, - CPI Variable LG3 None
Static wind Static
3DWind9 180, + CPE, + CPI Variable LG3 None
Static wind Static
3DWind10 180, + CPE, - CPI Variable LG3 None
Static wind Static
3DWind11 180, - CPE, + CPI Variable LG3 None
Static wind Static
3DWind12 180, - CPE, - CPI Variable LG3 None
Static wind Static
3DWind13 270, + CPE, + CPI Variable LG3 None
Static wind Static
3DWind14 270, + CPE, - CPI Variable LG3 None
Static wind Static
3DWind15 270, - CPE, + CPI Variable LG3 None
Static wind Static
3DWind16 270, - CPE, - CPI Variable LG3 None
Static wind Static

2. Stability combinations
Name Load cases Coeff.
[-]
S1 LC1 - Self weight 1.35
LC2 - Postojan tovar 1.35
LC3 - Sneg 1.50
3DWind14 - 270, + CPE, - CPI 0.90
S1/1 - 1.70
S1/2 - 6.04
S1/3 - 18.86
S1/4 - 20.63
S1/5 - 23.41
S1/6 - 27.08
S1/7 - 28.15
S1/8 - 28.16
S1/9 - 28.54
S1/10 - 28.54
S1/11 - 28.96
S1/12 - 28.96
S1/13 - 29.71
S1/14 - 29.72
S1/15 - 30.53
S1/16 - 30.53
S1/17 - 30.80
S1/18 - 31.37
S1/19 - 31.38
S1/20 - 32.09
S1/21 - 32.09
S1/22 - 32.74
S1/23 - 32.74
S1/24 - 33.05
S1/25 - 33.05
S1/26 - 34.53
 Name Load cases Coeff.
[-]
S1/27 - 36.12
S1/28 - 37.70
S1/29 - 40.79
S1/30 - 41.44
S1/31 - 41.87
S1/32 - 41.88
S1/33 - 46.30
S1/34 - 49.55
S1/35 - 49.55
S1/36 - 53.36
S1/37 - 55.54
S1/38 - 69.86
S1/39 - 87.88
S1/40 - 93.96
S1/41 - 128.13
S1/42 - 128.13
S1/43 - 128.24
S1/44 - 131.50
S1/45 - 131.50
S1/46 - 132.10
S1/47 - 132.11
S1/48 - 133.90
S1/49 - 133.90
S1/50 - 136.08

Utotal [mm]
1010.9

1000.0

800.0

600.0

400.0

200.0

0.0

Z
Y
X

3. Wind data
Name Type Roof type Roof overhangs Swap outer surface Load direction Region Zones +Cpe -Cpe underside Cpe
WD1 Wall ✗ 0 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 A -1.2000 -1.2000
4 B -0.8000 -0.8000
90 1 D 0.7000 0.7000
2 D 0.7000 0.7000
180 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
Name Type Roof type Roof overhangs Swap outer surface Load direction Region Zones +Cpe -Cpe underside Cpe
3 A -1.2000 -1.2000
4 B -0.8000 -0.8000
270 1 E -0.3000 -0.3000
2 E -0.3000 -0.3000
WD2 Wall ✗ 0 1 E -0.3667 -0.3667
90 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 C -0.5000 -0.5000
180 1 D 0.7333 0.7333
270 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 C -0.5000 -0.5000
WD3 Wall ✗ 0 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 A -1.2000 -1.2000
4 B -0.8000 -0.8000
90 1 E -0.3000 -0.3000
2 E -0.3000 -0.3000
180 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 A -1.2000 -1.2000
4 B -0.8000 -0.8000
270 1 D 0.7000 0.7000
2 D 0.7000 0.7000
WD4 Wall ✗ 0 1 D 0.7333 0.7333
90 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 C -0.5000 -0.5000
180 1 E -0.3667 -0.3667
270 1 A -1.2000 -1.2000
2 B -0.8000 -0.8000
3 C -0.5000 -0.5000
WD5 Roof Flat ✗ ✗ 0 1 H -0.7000 -0.7000
2 I 0.2000 -0.2000
90 1 F2 -1.8000 -1.8000
2 G -1.2000 -1.2000
3 H -0.7000 -0.7000
4 I 0.2000 -0.2000
180 1 F1 -1.8000 -1.8000
2 F2 -1.8000 -1.8000
3 G -1.2000 -1.2000
4 H -0.7000 -0.7000
270 1 F1 -1.8000 -1.8000
2 G -1.2000 -1.2000
3 H -0.7000 -0.7000
4 I 0.2000 -0.2000
WD6 Roof Flat ✗ ✗ 0 1 F1 -1.8000 -1.8000
2 F2 -1.8000 -1.8000
3 G -1.2000 -1.2000
4 H -0.7000 -0.7000
90 1 F1 -1.8000 -1.8000
2 G -1.2000 -1.2000
3 H -0.7000 -0.7000
4 I 0.2000 -0.2000
180 1 H -0.7000 -0.7000
2 I 0.2000 -0.2000
270 1 F2 -1.8000 -1.8000
2 G -1.2000 -1.2000
3 H -0.7000 -0.7000
4 I 0.2000 -0.2000

4. Surface load
Name Dir Type Coeff Value Load case System Loc
[kN/m2]
SF5 Z Force -0.55 LC2 - Postojan tovar GCS Length
SF6 Z Force -0.55 LC2 - Postojan tovar GCS Length
SF7 Z Force -0.55 LC2 - Postojan tovar GCS Length
SF8 Z Force -0.55 LC2 - Postojan tovar GCS Length
SF9 Z Force -0.55 LC2 - Postojan tovar GCS Length
SF10 Z Force -0.55 LC2 - Postojan tovar GCS Length
SF11 Z Snow -1.000 -0.66 LC3 - Sneg GCS Projection
SF12 Z Snow -1.000 -0.66 LC3 - Sneg GCS Projection
5. 1D internal forces
Linear calculation
Combination: ULS-Set B (auto)
Coordinate system: Principal
Extreme 1D: Global
Selection: All
Name dx Case N Vy Vz Mx My Mz
[m] [kN] [kN] [kN] [kNm] [kNm] [kNm]
B5 0.000 ULS-Set B -172.95 1.84 -34.34 0.00 0.00 0.00
(auto)/1
B9 0.000 ULS-Set B 34.04 0.16 -4.03 -0.04 8.73 -1.00
(auto)/2
B1 8.000 ULS-Set B 5.13 -36.74 -1.75 0.00 32.12 -9.18
(auto)/2
B140 8.000 ULS-Set B 5.13 36.74 -1.75 0.00 32.12 9.18
(auto)/2
B7 8.016 ULS-Set B -36.21 0.58 -109.65 0.12 -254.25 0.12
(auto)/1
B21 0.000 ULS-Set B -134.95 -3.08 42.88 0.00 0.00 0.00
(auto)/3
B4 6.412+ ULS-Set B -13.39 -0.78 -42.54 -1.06 -32.86 1.25
(auto)/4
B3 6.412+ ULS-Set B -13.39 0.78 -42.54 1.06 -32.86 -1.25
(auto)/4
B7 8.016 ULS-Set B -40.09 0.08 -107.82 -0.13 -271.52 0.43
(auto)/5
B6 8.000 ULS-Set B -121.53 -0.12 33.05 0.00 271.28 -0.97
(auto)/6
B140 4.000- ULS-Set B -55.36 0.79 -0.11 0.00 11.08 -64.28
(auto)/7
B1 4.000- ULS-Set B -55.36 -0.79 -0.11 0.00 11.08 64.28
(auto)/7
Name Combination key
ULS-Set B (auto)/1 1.35*LC1 + 1.35*LC2 + 1.50*LC3 + 0.90*3DWind14
ULS-Set B (auto)/2 LC1 + LC2 + 1.50*3DWind1
ULS-Set B (auto)/3 1.35*LC1 + 1.35*LC2 + 1.05*LC3 + 1.50*3DWind5
ULS-Set B (auto)/4 1.35*LC1 + 1.35*LC2 + 1.05*LC3 + 1.50*3DWind14
ULS-Set B (auto)/5 1.35*LC1 + 1.35*LC2 + 1.50*LC3 + 0.90*3DWind10
ULS-Set B (auto)/6 1.35*LC1 + 1.35*LC2 + 1.50*LC3 + 0.90*3DWind2
ULS-Set B (auto)/7 1.35*LC1 + 1.35*LC2 + 1.05*LC3 + 1.50*3DWind3

6. 1D deformations
Linear calculation
Combination: SLS-Char (auto)
Coordinate system: Global
Extreme 1D: Global
Selection: All
Deformations
Name dx Case ux uy uz φx φy φz Utotal
[m] [mm] [mm] [mm] [mrad] [mrad] [mrad] [mm]
B65 7.500 SLS-Char -24.3 0.0 -0.2 0.0 -0.1 0.0 24.3
(auto)/1
B66 7.500 SLS-Char 24.3 0.0 -0.2 0.0 0.1 0.0 24.3
(auto)/2
B140 8.000 SLS-Char -0.5 -69.8 -0.1 3.1 1.0 0.5 69.8
(auto)/3
B1 8.000 SLS-Char -0.5 69.8 -0.1 -3.1 1.0 -0.5 69.8
(auto)/4
B14 3.500 SLS-Char 0.0 -41.4 -40.2 0.7 0.0 0.0 57.7
(auto)/5
B9 4.500 SLS-Char -1.1 69.5 4.2 0.1 1.3 0.1 69.7
(auto)/6
B1 0.000 SLS-Char 0.0 0.0 0.0 -14.2 -0.5 -0.5 0.0
(auto)/7
B140 0.000 SLS-Char 0.0 0.0 0.0 14.2 -0.5 0.5 0.0
(auto)/8
B8 5.344 SLS-Char 1.1 -41.5 -13.7 2.1 -5.5 0.0 43.7
(auto)/5
B7 5.344 SLS-Char -1.1 -41.5 -13.7 2.1 5.5 0.0 43.7
(auto)/5
B10 3.500 SLS-Char 17.7 -0.3 -0.3 -0.7 1.4 -1.6 17.7
(auto)/9
B16 3.500 SLS-Char -17.7 -0.3 -0.3 -0.7 -1.4 1.6 17.7
(auto)/10
B44 3.000- SLS-Char 0.0 69.4 -35.3 0.1 0.0 0.0 77.8
Name dx Case ux uy uz φx φy φz Utotal
[m] [mm] [mm] [mm] [mrad] [mrad] [mrad] [mm]
(auto)/11
Name Combination key
SLS-Char (auto)/1 LC1 + LC2 + 0.70*LC3 + 3DWind12
SLS-Char (auto)/2 LC1 + LC2 + 0.70*LC3 + 3DWind4
SLS-Char (auto)/3 LC1 + LC2 + 0.70*LC3 + 3DWind16
SLS-Char (auto)/4 LC1 + LC2 + 0.70*LC3 + 3DWind8
SLS-Char (auto)/5 LC1 + LC2 + LC3 + 0.60*3DWind14
SLS-Char (auto)/6 LC1 + LC2 + 3DWind6
SLS-Char (auto)/7 LC1 + LC2 + 3DWind8
SLS-Char (auto)/8 LC1 + LC2 + 3DWind16
SLS-Char (auto)/9 LC1 + LC2 + 3DWind3
SLS-Char (auto)/10 LC1 + LC2 + 3DWind11
SLS-Char (auto)/11 LC1 + LC2 + 0.70*LC3 + 3DWind6

7. Analysis model

Z
Y
X
8. LC2 / Tot. value

Z
Y
X
9. LC3 / Tot. value

Z
Y
X
10. 3DWind1 / Tot. value

Z
Y
X

11. 3DWind2 / Tot. value

Z
Y
X
12. 3DWind3 / Tot. value

Z
Y
X

13. 3DWind4 / Tot. value

Z
Y
X
14. 3DWind5 / Tot. value

Z
Y
X

15. 3DWind6 / Tot. value

Z
Y
X
16. 3DWind7 / Tot. value

Z
Y
X

17. 3DWind8 / Tot. value

Z
Y
X
18. 3DWind9 / Tot. value

Z
Y
X

19. 3DWind10 / Tot. value

Z
Y
X
20. 3DWind11 / Tot. value

Z
Y
X

21. 3DWind12 / Tot. value

Z
Y
X
22. 3DWind13 / Tot. value

Z
Y
X

23. 3DWind14 / Tot. value

Z
Y
X
24. 3DWind15 / Tot. value

Z
Y
X

25. 3DWind16 / Tot. value

Z
Y
X
26. 1D internal forces; M_y

Z
Y
X

27. 1D internal forces; V_z

Z
Y
X
28. 1D internal forces; N

Z
Y
X

29. 1D internal forces; M_z

Z
Y
X
30. EC-EN 1993 Steel check ULS
Linear calculation
Combination: ULS-Set B (auto)
Coordinate system: Principal
Extreme 1D: Global
Selection: All
Filter: Cross-section = CS6 - IPE500
EN 1993-1-1 Code Check
National annex: Standard EN
Member B127 1.603 / 8.016 m IPE500 S 235 ULS-Set B (auto) 0.56 -
Combination key
ULS-Set B (auto) / 1.35*LC1 + 1.35*LC2 + 1.50*LC3 +
0.90*3DWind10
Partial safety factors
γM0 for resistance of cross-sections 1.00
γM1 for resistance to instability 1.00
γM2 for resistance of net sections 1.25
Material
Yield strength fy 235.0 MPa
Ultimate strength fu 360.0 MPa
Fabrication Rolled
...::SECTION CHECK::...
The critical check is on position 1.603 m
Internal forces Calculated Unit
NEd -35.51 kN
Vy,Ed 1.63 kN
Vz,Ed -9.02 kN
TEd -0.05 kNm
My,Ed 173.84 kNm
Mz,Ed 0.74 kNm
Classification for cross-section design
Classification according to EN 1993-1-1 article 5.5.2
Classification of Internal and Outstand parts according to EN 1993-1-1 Table 5.2 Sheet 1 & 2
Id Type c t σ1 σ2 Ψ kσ α c/t Class 1 Class 2 Class 3 Class
[mm] [mm] [kN/m2] [kN/m2] [-] [-] [-] [-] Limit Limit Limit
[-] [-] [-]
1 SO 74 16 -8.510e+04 -8.765e+04
3 SO 74 16 -8.329e+04 -8.074e+04
4 I 426 10 -7.374e+04 7.988e+04 -0.9 0.5 41.8 68.3 79.0 114.2 1
5 SO 74 16 9.124e+04 9.379e+04 1.0 0.4 1.0 4.6 9.0 10.0 13.8 1
7 SO 74 16 8.944e+04 8.689e+04 1.0 0.4 1.0 4.6 9.0 10.0 13.9 1
Note: The Classification limits have been set according to Semi-Comp+.
The cross-section is classified as Class 1
Compression check
According to EN 1993-1-1 article 6.2.4 and formula (6.9)

Bending moment check for My

According to EN 1993-1-1 article 6.2.5 and formula (6.12),(6.13)

Bending moment check for Mz

According to EN 1993-1-1 article 6.2.5 and formula (6.12),(6.13)

Shear check for Vy

According to EN 1993-1-1 article 6.2.6 and formula (6.17)
Shear check for Vz
According to EN 1993-1-1 article 6.2.6 and formula (6.17)

Torsion check
According to EN 1993-1-1 article 6.2.7 and formula (6.23)

Note: The unity check for torsion is lower than the limit value of 0.05. Therefore torsion is considered as
insignificant and is ignored in the combined checks.
Combined bending, axial force and shear force check
According to EN 1993-1-1 article 6.2.9.1 and formula (6.41)

Note: Since the shear forces are less than half the plastic shear resistances their effect on the moment
resistances is neglected.
Note: Since the axial force satisfies both criteria (6.33) and (6.34) of EN 1993-1-1 article 6.2.9.1(4)
its effect on the moment resistance about the y-y axis is neglected.
Note: Since the axial force satisfies criteria (6.35) of EN 1993-1-1 article 6.2.9.1(4) its effect on the moment
resistance about the z-z axis is neglected.
The member satisfies the section check.
...::STABILITY CHECK::...
Classification for member buckling design
Decisive position for stability classification: 8.016 m
Classification according to EN 1993-1-1 article 5.5.2
Classification of Internal and Outstand parts according to EN 1993-1-1 Table 5.2 Sheet 1 & 2
Id Type c t σ1 σ2 Ψ kσ α c/t Class 1 Class 2 Class 3 Class
[mm] [mm] [kN/m2] [kN/m2] [-] [-] [-] [-] Limit Limit Limit
[-] [-] [-]
1 SO 74 16 1.403e+05 1.418e+05 1.0 0.4 1.0 4.6 9.0 10.0 13.8 1
3 SO 74 16 1.392e+05 1.377e+05 1.0 0.4 1.0 4.6 9.0 10.0 13.8 1
4 I 426 10 1.234e+05 -1.165e+05 -0.9 0.5 41.8 67.8 78.6 116.7 1
5 SO 74 16 -1.334e+05 -1.349e+05
7 SO 74 16 -1.323e+05 -1.308e+05
Note: The Classification limits have been set according to Semi-Comp+.
The cross-section is classified as Class 1
Flexural Buckling check
According to EN 1993-1-1 article 6.3.1.1 and formula (6.46)
Torsional(-Flexural) Buckling check
According to EN 1993-1-1 article 6.3.1.1 and formula (6.46)
Note: For this I-section the Torsional(-Flexural) buckling resistance is higher than the resistance
for Flexural buckling. Therefore Torsional(-Flexural) buckling is not printed on the output.
Lateral Torsional Buckling check
According to EN 1993-1-1 article 6.3.2.1 & 6.3.2.3 and formula (6.54)

Note: The slenderness or bending moment is such that Lateral Torsional Buckling effects
may be ignored according to EN 1993-1-1 article 6.3.2.2(4).
Note: C parameters are determined according to ECCS 119 2006 / Galea 2002.
Bending and axial compression check
According to EN 1993-1-1 article 6.3.3 and formula (6.61),(6.62)
Maximum moment My,Ed is derived from beam B127 position 8.016 m.
Maximum moment Mz,Ed is derived from beam B127 position 0.000 m.
Shear Buckling check
According to EN 1993-1-5 article 5 & 7.1 and formula (5.10) & (7.1)

Note: The web slenderness is such that Shear Buckling effects may be ignored
according to EN 1993-1-5 article 5.1(2).
The member satisfies the stability check.

31. EC-EN 1993 Steel check ULS

Linear calculation
Combination: ULS-Set B (auto)
Coordinate system: Principal
Extreme 1D: Global
Selection: All
Filter: Cross-section = CS7 - HEA450
EN 1993-1-1 Code Check
National annex: Standard EN
Member B126 0.000 / 8.000 m HEA450 S 235 ULS-Set B (auto) 0.51 -
Combination key
ULS-Set B (auto) / 1.35*LC1 + 1.35*LC2 + 1.05*LC3 +
1.50*3DWind6
Partial safety factors
γM0 for resistance of cross-sections 1.00
γM1 for resistance to instability 1.00
γM2 for resistance of net sections 1.25
Material
Yield strength fy 235.0 MPa
Ultimate strength fu 360.0 MPa
Fabrication Rolled
...::SECTION CHECK::...
The critical check is on position 0.000 m
Internal forces Calculated Unit
NEd -166.54 kN
Vy,Ed -3.10 kN
Vz,Ed 34.39 kN
TEd 0.00 kNm
My,Ed 0.00 kNm
Mz,Ed 0.00 kNm
Classification for cross-section design
Classification according to EN 1993-1-1 article 5.5.2
Classification of Internal and Outstand parts according to EN 1993-1-1 Table 5.2 Sheet 1 & 2
Id Type c t σ1 σ2 Ψ kσ α c/t Class 1 Class 2 Class 3 Class
[mm] [mm] [kN/m2] [kN/m2] [-] [-] [-] [-] Limit Limit Limit
[-] [-] [-]
1 SO 117 21 9.353e+03 9.353e+03 1.0 0.4 1.0 5.6 9.0 10.0 14.0 1
3 SO 117 21 9.353e+03 9.353e+03 1.0 0.4 1.0 5.6 9.0 10.0 14.0 1
4 I 344 12 9.353e+03 9.353e+03 1.0 1.0 29.9 28.0 34.0 38.0 2
5 SO 117 21 9.353e+03 9.353e+03 1.0 0.4 1.0 5.6 9.0 10.0 14.0 1
7 SO 117 21 9.353e+03 9.353e+03 1.0 0.4 1.0 5.6 9.0 10.0 14.0 1
Note: The Classification limits have been set according to Semi-Comp+.
The cross-section is classified as Class 2
Compression check
According to EN 1993-1-1 article 6.2.4 and formula (6.9)

Shear check for Vy

According to EN 1993-1-1 article 6.2.6 and formula (6.17)

Shear check for Vz

According to EN 1993-1-1 article 6.2.6 and formula (6.17)

The member satisfies the section check.

...::STABILITY CHECK::...
Classification for member buckling design
Decisive position for stability classification: 0.500 m
Classification according to EN 1993-1-1 article 5.5.2
Classification of Internal and Outstand parts according to EN 1993-1-1 Table 5.2 Sheet 1 & 2
Id Type c t σ1 σ2 Ψ kσ α c/t Class 1 Class 2 Class 3 Class
[mm] [mm] [kN/m2] [kN/m2] [-] [-] [-] [-] Limit Limit Limit
[-] [-] [-]
1 SO 117 21 4.104e+03 6.021e+03 0.7 0.5 1.0 5.6 9.0 10.0 14.2 1
3 SO 117 21 3.033e+03 1.115e+03 0.4 0.8 1.0 5.6 9.0 10.0 19.0 1
4 I 344 12 4.572e+03 1.378e+04 0.3 1.0 29.9 28.0 34.0 49.5 2
5 SO 117 21 1.425e+04 1.233e+04 0.9 0.5 1.0 5.6 9.0 10.0 14.5 1
7 SO 117 21 1.532e+04 1.724e+04 0.9 0.4 1.0 5.6 9.0 10.0 13.9 1
Note: The Classification limits have been set according to Semi-Comp+.
The cross-section is classified as Class 2
Flexural Buckling check
According to EN 1993-1-1 article 6.3.1.1 and formula (6.46)
Torsional(-Flexural) Buckling check
According to EN 1993-1-1 article 6.3.1.1 and formula (6.46)
Note: For this I-section the Torsional(-Flexural) buckling resistance is higher than the resistance
for Flexural buckling. Therefore Torsional(-Flexural) buckling is not printed on the output.
Bending and axial compression check
According to EN 1993-1-1 article 6.3.3 and formula (6.61),(6.62)
Maximum moment My,Ed is derived from beam B126 position 8.000 m.
Maximum moment Mz,Ed is derived from beam B126 position 8.000 m.
Shear Buckling check
According to EN 1993-1-5 article 5 & 7.1 and formula (5.10) & (7.1)

Note: The web slenderness is such that Shear Buckling effects may be ignored
according to EN 1993-1-5 article 5.1(2).
The member satisfies the stability check.

32. EC-EN 1993 Steel Check SLS

Linear calculation
Combination: SLS-Char (auto)
Coordinate system: Principal
Extreme 1D: Global
Selection: All
Filter: Cross-section = CS6 - IPE500
Deformation u_z
Name dx Case Cross-section uz,tot uz,var Lim. uz,tot Lim. Check Check Camber Camber Check uz
[m] [mm] [mm] [mm] uz,var uz,tot uz,var dx uz uz,max [-]
[mm] [-] [-] [mm] [mm]
B7 0.000 SLS-Char CS6 - IPE500 -32.1 -16.8 80.2 44.5 0.40 0.38 - - 0.40
(auto)/1
B67 7.214+ SLS-Char CS6 - IPE500 0.2 1.7 80.2 44.5 0.00 0.04 - - 0.04
(auto)/2
Name Combination key
SLS-Char (auto)/1 LC1 + LC2 + LC3 + 0.60*3DWind14
SLS-Char (auto)/2 LC1 + LC2 + 3DWind11
33. EC-EN 1993 Steel check ULS; Overall check

Z
Y
X
34. EC-EN 1993 Steel check ULS; Overall check

Z
Y
X
35. 1D deformations; u_z

Z
Y
X