8M0165094
8M0165094
Manual
Operation
Installation
Maintenance
8M0165094 1019 eng
© 2019 Mercury Marine 15/20 EFI FourStroke
eng
Welcome
You have selected one of the finest marine power packages available. It
incorporates numerous design features to ensure operating ease and durability.
With proper care and maintenance, you will enjoy using this product for many
boating seasons. To ensure maximum performance and carefree use, we ask
that you thoroughly read this manual.
The Operation and Maintenance Manual contains specific instructions for using
and maintaining your product. Keep this manual with the product for ready
reference whenever you are on the water.
Thank you for purchasing one of our products. We sincerely hope your boating
will be pleasant.
Mercury Marine, Fond du Lac, Wisconsin, U.S.A.
Name / function:
Christopher D. Drees, President,
Mercury Marine
Notice
Throughout this publication and on your power package, safety alerts labeled
! WARNING
Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
! CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
eng i
Additional alerts provide information that requires special attention:
NOTICE
Indicates a situation which, if not avoided, could result in engine or major
component failure.
IMPORTANT: The operator (driver) is responsible for the correct and safe
operation of the boat, the equipment aboard, and the safety of all occupants
aboard. We strongly recommend that the operator read this Operation and
Maintenance Manual and thoroughly understand the operational instructions for
the power package and all related accessories before the boat is used.
California Proposition 65
WARNING: This product can expose you to chemicals including
gasoline engine exhaust, which is known to the State of
California to cause cancer and birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Descriptions and specifications contained herein were in effect at the time this
was approved for printing. Mercury Marine, whose policies are based on
continuous improvement, reserves the right to discontinue models at any time
or to change specifications or designs without notice and without incurring
obligation.
Warranty Message
The product you have purchased comes with a Mercury Marine Limited
Warranty. The terms of the warranty are set forth in the Warranty Manual,
which can be accessed any time on the Mercury Marine website, at http://
www.mercurymarine.com/warranty‑manual. The Warranty Manual contains a
description of what is covered, what is not covered, the duration of coverage,
how to best obtain warranty coverage, important disclaimers, limitations,
and waivers, and other related information. Please review this important
information.
ii eng
Mercury Marine products are designed and manufactured to comply with our
own high quality standards, applicable industry standards and regulations, and
certain emissions regulations. At Mercury Marine every engine is operated and
tested before it is boxed for shipment to make sure that the product is ready for
use. In addition, certain Mercury Marine products are tested in a controlled and
monitored environment, for up to 10 hours of engine run time, in order to verify
and make a record of compliance with applicable standards and regulations. All
Mercury Marine product, sold as new, receives the applicable limited warranty
coverage, whether the engine participated in one of the test programs
described above or not.
Identification Records
The serial numbers are the manufacturer’s keys to numerous engineering
details that apply to your Mercury Marine power package. When contacting
Mercury Marine about service, always specify model and serial numbers.
Please record the following applicable information:
Outboard
Engine Model and Horsepower
Engine Serial Number
Gear Ratio
Propeller Number Pitch Diameter
eng iii
eng iv
General Information
Boater's Responsibilities..................................................................................... 1
High‑Speed and High‑Performance Boat Operation.......................................... 1
Outboard Remote Control Models ..................................................................... 1
Remote Steering Notice...................................................................................... 2
Lanyard Stop Switch........................................................................................... 2
Protecting People in the Water........................................................................... 4
Passenger Safety Message ‑ Pontoon Boats and Deck Boats........................... 5
Wave and Wake Jumping................................................................................... 6
Impact with Underwater Hazards........................................................................ 7
Exhaust Emissions............................................................................................. 9
Safe Boating Recommendations...................................................................... 11
Recording Serial Number ................................................................................ 14
Model Year Production Code............................................................................ 14
Specifications—15, 20 HP................................................................................ 15
Conditions Affecting Performance.................................................................... 17
Installation
Transporting
eng v
Fuel and Oil
Fuel Requirements........................................................................................... 44
Low Permeation Fuel Hose Requirement ........................................................ 45
EPA Pressurized Portable Fuel Tank Requirements........................................ 45
Fuel Demand Valve (FDV) Requirement.......................................................... 45
Mercury Marine's Pressurized Portable Fuel Tank........................................... 46
Filling Fuel Tank............................................................................................... 47
Engine Oil Recommendations.......................................................................... 47
Checking Engine Oil......................................................................................... 48
Operation
vi eng
Maintenance
Storage
Troubleshooting
Starter Motor Will Not Crank the Engine (Electric Start Models) ................... 124
Engine Will Not Start....................................................................................... 124
Engine Runs Erratically.................................................................................. 124
Performance Loss........................................................................................... 125
Battery Will Not Hold Charge.......................................................................... 125
eng vii
Maintenance Log
viii eng
GENERAL INFORMATION
Boater's Responsibilities
The operator (driver) is responsible for the correct and safe operation of the
boat and the safety of its occupants and general public. It is strongly
recommended that each operator read and understand this entire manual
before operating the outboard.
Be sure that at least one additional person onboard is instructed in the basics
of starting and operating the outboard and boat handling in case the driver is
unable to operate the boat.
! WARNING
Starting the engine with the drive in gear can cause serious injury or death.
Never operate a boat that does not have a neutral‑safety‑protection device.
63103
eng 1
GENERAL INFORMATION
Remote Steering Notice
The steering link rod that connects the steering cable to the engine must be
fastened utilizing self‑locking nuts. These self‑locking nuts must never be
replaced with common nonlocking nuts; they will work loose and vibrate off,
allowing the link rod to disengage from the steering cable.
! WARNING
Improper fasteners or improper installation procedures can result in
loosening or disengagement of the steering link rod. This can cause a
sudden, unexpected loss of boat control, resulting in serious injury or death
due to occupants being thrown within or out of the boat. Always use required
components and follow instructions and torque procedures.
63290
Self-locking nuts
2 eng
GENERAL INFORMATION
The lanyard cord is usually 122–152 cm (4–5 feet) in length when stretched out,
with an element on one end made to be inserted into the switch and a clip on
the other end for attaching to the operator's PFD or wrist. The lanyard is coiled
to make its at‑rest condition as short as possible to minimize the likelihood of
lanyard entanglement with nearby objects. Its stretched‑out length is made to
minimize the likelihood of accidental activation should the operator choose to
move around in an area close to the normal operator's position. If it is desired
to have a shorter lanyard, wrap the lanyard around the operator's wrist or leg,
or tie a knot in the lanyard.
64164
Read the following Safety Information before proceeding.
Important Safety Information: The purpose of a lanyard stop switch is to stop
the engine when the operator moves far enough away from the operator's
position to activate the switch. This would occur if the operator accidentally falls
overboard or moves within the boat a sufficient distance from the operator's
position. Falling overboard and accidental ejections are more likely to occur in
certain types of boats such as low sided inflatables, bass boats, high
performance boats, and light, sensitive handling fishing boats operated by a
hand tiller. Falling overboard and accidental ejections are also likely to occur as
a result of poor operating practices such as sitting on the back of the seat or
gunwale at planing speeds, standing at planing speeds, sitting on elevated
fishing boat decks, operating at planing speeds in shallow or obstacle infested
waters, releasing your grip on a steering wheel or tiller handle that is pulling in
one direction, drinking alcohol or consuming drugs, or daring high speed boat
maneuvers.
While activation of the lanyard stop switch will stop the engine immediately, a
boat will continue to coast for some distance depending upon the velocity and
degree of any turn at shut down. However, the boat will not complete a full
circle. While the boat is coasting, it can cause injury to anyone in the boat's
path as seriously as the boat would when under power.
We strongly recommend that other occupants be instructed on proper starting
and operating procedures should they be required to operate the engine in an
emergency (if the operator is accidentally ejected).
eng 3
GENERAL INFORMATION
! WARNING
If the operator falls out of the boat, stop the engine immediately to reduce the
possibility of serious injury or death from being struck by the boat. Always
properly connect the operator to the stop switch using a lanyard.
! WARNING
Avoid serious injury or death from deceleration forces resulting from
accidental or unintended stop switch activation. The boat operator should
never leave the operator's station without first disconnecting the stop switch
lanyard from the operator.
21604
4 eng
GENERAL INFORMATION
Always slow down and exercise extreme caution any time you are boating in an
area where there might be people in the water.
Whenever a boat is moving (coasting) and the outboard gear shift is in neutral
position, there is sufficient force by the water on the propeller to cause the
propeller to rotate. This neutral propeller rotation can cause serious injury.
WHILE THE BOAT IS STATIONARY
! WARNING
A spinning propeller, a moving boat, or any solid device attached to the boat
can cause serious injury or death to swimmers. Stop the engine immediately
whenever anyone in the water is near your boat.
Shift the outboard into neutral and shut off the engine before allowing people to
swim or be in the water near your boat.
26782
eng 5
GENERAL INFORMATION
! WARNING
Sitting or standing in an area of the boat not designed for passengers at
speeds above idle can cause serious injury or death. Stay back from the front
end of deck boats or raised platforms and remain seated while the boat is in
motion.
26783
26784
The primary concern is the boat changing direction while in the midst of the
jump. In such case, the landing may cause the boat to veer violently in a new
direction. Such a sharp change in direction can cause occupants to be thrown
out of their seats, or out of the boat.
6 eng
GENERAL INFORMATION
! WARNING
Wave or wake jumping can cause serious injury or death from occupants
being thrown within or out of the boat. Avoid wave or wake jumping whenever
possible.
There is another less common hazardous result from allowing your boat to
launch off a wave or wake. If the bow of your boat pitches down far enough
while airborne, upon water contact it may penetrate under the water surface
and submarine for an instant. This will bring the boat to a nearly instantaneous
stop and can send the occupants flying forward. The boat may also steer
sharply to one side.
26785
eng 7
GENERAL INFORMATION
! WARNING
Avoid serious injury or death from all or part of an outboard or drive unit
coming into the boat after striking a floating or underwater object. When
operating in waters where objects may be at the surface or just under the
surface of the water, reduce your speed and keep a vigilant lookout.
Examples of objects that can cause engine damage are dredging pipes,
bridge supports, wing dams, trees, stumps, and rocks.
! WARNING
Operating a boat or engine with impact damage can result in product
damage, serious injury, or death. If the vessel experiences any form of
impact, have an authorized Mercury Marine dealer inspect and repair the
vessel or power package.
8 eng
GENERAL INFORMATION
Models with Clamp Screws:
Some outboards come with transom bracket clamp screws. The use of clamp
bracket screws alone is insufficient to properly and safely secure the outboard
to the transom. Proper installation of the outboard includes bolting the engine to
the boat through the transom. Refer to Engine Installation ‑ Installing
Outboard for more complete installation information.
! WARNING
Failure to correctly fasten the outboard could result in the outboard propelling
off the boat transom resulting in property damage, serious injury, or death.
Before operation, the outboard must be correctly installed with the required
mounting hardware.
This product must be secured to the transom with the required mounting
hardware. If the outboard strikes an underwater object, the required mounting
hardware prevents the outboard from propelling off the transom. A decal on the
swivel bracket reminds the installer of the potential hazard.
WARNING
52375
Exhaust Emissions
BE ALERT TO CARBON MONOXIDE POISONING
Carbon monoxide (CO) is a deadly gas that is present in the exhaust fumes of
all internal combustion engines, including the engines that propel boats, and
the generators that power boat accessories. By itself, CO is odorless, colorless,
and tasteless, but if you can smell or taste engine exhaust, you are inhaling
CO.
Early symptoms of carbon monoxide poisoning, which are similar to the
symptoms of seasickness and intoxication, include headache, dizziness,
drowsiness, and nausea.
eng 9
GENERAL INFORMATION
! WARNING
Inhaling engine exhaust gases can result in carbon monoxide poisoning,
which can lead to unconsciousness, brain damage, or death. Avoid exposure
to carbon monoxide.
Stay clear from exhaust areas when engine is running. Keep the boat
well‑ventilated while at rest or underway.
co co
co co
co co
41127
POOR VENTILATION
Under certain running and/or wind conditions, permanently enclosed or canvas
enclosed cabins or cockpits with insufficient ventilation may draw in carbon
monoxide. Install one or more carbon monoxide detectors in your boat.
Although the occurrence is rare, on a very calm day, swimmers and
passengers in an open area of a stationary boat that contains, or is near, a
running engine may be exposed to a hazardous level of carbon monoxide.
10 eng
GENERAL INFORMATION
1. Examples of poor ventilation while the boat is stationary:
a
b
21626
a b
21628
a - Operating the boat with the trim angle of the bow too high
b - Operating the boat with no forward hatches open (station wagon effect)
eng 11
GENERAL INFORMATION
Tools necessary for minor repairs
Anchor and extra anchor line
Manual bilge pump and extra drain plugs
Drinking water
Radio
Paddle or oar
Spare propeller, thrust hubs, and an appropriate wrench
First aid kit and instructions
Waterproof storage containers
Spare operating equipment, batteries, bulbs, and fuses
Compass and map or chart of the area
Personal flotation device (one per person onboard)
Watch for signs of weather change and avoid foul weather and rough‑sea
boating.
Tell someone where you are going and when you expect to return.
Passenger boarding.
• Stop the engine whenever passengers are boarding, unloading, or are
near the back (stern) of the boat. Shifting the drive unit into neutral is not
sufficient.
Use personal flotation devices.
• Federal law requires that there be a U.S. Coast Guard‑approved life
jacket (personal flotation device), correctly sized and readily accessible
for every person onboard, plus a throwable cushion or ring. We strongly
advise that everyone wear a life jacket at all times while in the boat.
Prepare other boat operators.
• Instruct at least one person onboard in the basics of starting and
operating the engine and boat handling in case the driver becomes
disabled or falls overboard.
Do not overload your boat.
• Most boats are rated and certified for maximum load (weight) capacities
(refer to your boat's capacity plate). Know your boat's operating and
loading limitations. Know if your boat will float if it is full of water. When in
doubt, contact your authorized Mercury Marine dealer or the boat
manufacturer.
Ensure that everyone in the boat is properly seated.
12 eng
GENERAL INFORMATION
• Do not allow anyone to sit or ride on any part of the boat that was not
intended for such use. This includes the backs of seats, gunwales,
transom, bow, decks, raised fishing seats, and any rotating fishing seat.
Passengers should not sit or ride anywhere that sudden unexpected
acceleration, sudden stopping, unexpected loss of boat control, or sudden
boat movement could cause a person to be thrown overboard or into the
boat. Ensure that all passengers have a proper seat and are in it before
any boat movement.
Never operate a boat while under the influence of alcohol or drugs. It is
the law.
• Alcohol or drugs can impair your judgment and greatly reduce your ability
to react quickly.
Know your boating area and avoid hazardous locations.
Be alert.
• The operator of the boat is responsible by law to maintain a proper
lookout by sight and hearing. The operator must have an unobstructed
view particularly to the front. No passengers, load, or fishing seats should
block the operator's view when the boat is above idle or planing transition
speed. Watch out for others, the water, and your wake.
Never drive your boat directly behind a water‑skier.
• Your boat traveling at 40 km/h (25 mph) will overtake a fallen skier who is
61 m (200 ft) in front of you in five seconds.
Watch fallen skiers.
• When using your boat for waterskiing or similar activities, always keep a
fallen or down skier on the operator's side of the boat while returning to
attend to the skier. The operator should always have the down skier in
sight and never back up to the skier or anyone in the water.
Report accidents.
• Boat operators are required by law to file a boating accident report with
their state boating law enforcement agency when their boat is involved in
certain boating accidents. A boating accident must be reported if 1) there
is loss of life or probable loss of life, 2) there is personal injury requiring
medical treatment beyond first aid, 3) there is damage to boats or other
property where the damage value exceeds $500.00, or 4) there is
complete loss of the boat. Seek further assistance from local law
enforcement.
eng 13
GENERAL INFORMATION
Recording Serial Number
It is important to record this number for future reference. The serial number is
located on the outboard as shown.
Model Number
XXXXXXX b
a Serial Number
XXXXX XX
XXXX XXX
HP XXX KW XXX
LB XXX KG XXX
Mercury Marine
Brunswick Corp.
c
d Made in Japan XX
70063
a- Serial number
b- Model designation
c- Year manufactured
d- Certified Europe Insignia (as applicable)
XXXXXXX
Serial Number
XXXXX XX
XXXX XXX
HP XXX KW XXX
LB XXX KG XXX
Mercury Marine
Brunswick Corp.
Made in Japan BX
14 eng
GENERAL INFORMATION
Model Year Manufactured Code
Alpha Production Code A B C D E F G H K X
Corresponding Number 1 2 3 4 5 6 7 8 9 0
Examples:
• BX = 2020
• HK = 2089
• AG = 2017
Specifications—15, 20 HP
Attributes Specification
11.0 kW (15 hp)
Power rating
14.7 kW (20 hp)
MH 46.7 kg (103 lbs)
MRC 44 kg (97 lbs)
MLH 48.5 kg (107 lbs)
EH 50.3 kg (111 lbs)
ELH 51.7 kg (114 lbs)
E 47.6 kg (105 lbs)
Weight
EL 49 kg (108 lbs)
EPT 52.6 kg (116 lbs)
ELPT 53.9 kg (119 lbs)
ELHPT 57.6 kg (127 lbs)
ProKicker–EXLHPT 58.9 kg (130 lbs)
ProKicker–EXLPT 55.3 kg (122 lbs)
Not in gear 900–1000 RPM
Engine idle speed
In gear 900–1000 RPM
Recommended RPM 15/20 hp model 5700–6200 RPM
range at WOT 15/20 JCI 5400–6100 RPM
61.0 mm x 57.0 mm
Bore x stroke
(2.402 in. x 2.244 in.)
Compression ratio 10.0:1
Starting system Manual/electric
Starter fuse 15 A, mini ATC
Computer controlled CDI
Ignition type
(capacitor discharge ignition)
Voltage regulator fuse 20 A, mini ATC
Spark plug NGK DCPR6E
eng 15
GENERAL INFORMATION
Attributes Specification
Spark plug gap 0.9 mm (0.035 in.)
Ignition timing at idle 6° BTDC
Ignition timing at WOT 28° BTDC
All models except
6500 RPM
RPM overspeed JCI
JCI models only 6300 RPM
ECM RPM limiter (Guardian) 2800 RPM
Over temperature 85 °C (185 °F)
Low oil pressure 26.3 kPa (3.8 psi)
Water pressure at idle 9 kPa (1.3 psi)
Water pressure at WOT 59 kPa (8.5 psi)
All temperatures FC‑W® 10W‑30
Oil type Alternate viscosity
FC‑W® 25W‑40
above 4 °C (40 °F)
Oil capacity 1.0 L (1.1 U.S. qt)
Alternator type Single phase
Alternator output at 900 RPM 4.6 A
Alternator output at 5000 RPM 11.5 A
Computer controlled
Fuel system sequential multiport electronic
fuel injection
Automotive unleaded
Fuel type (regular)
E10 maximum blend
Mechanical (low‑pressure)
Fuel pump type
Electric (high‑pressure)
Gear ratio 2.15:1
Gearcase capacity 460 ml (15.6 fl oz)
Premium Gear Lubricant or
Gear lubricant type
GL5 SAE 80W‑90 Weight
Dog type (forward–neutral–
Clutch
reverse)
Power Trim and Steering
Fluid or
Power tilt fluid
Automatic Transmission Fluid
(ATF) (Type Dexron III)
Power trim –4° to 71°
Trim/tilt range
Manual –4° to 76°
16 eng
GENERAL INFORMATION
Attributes Specification
Short 38 cm (15 in.)
Transom height Long 51 cm (20 in.)
Extra long 63.5 cm (25 in.)
Above 0 °C (32 °F) 465 MCA, 350 CCA
Battery requirements
Below 0 °C (32 °F) 800 MCA, 650 CCA
Sound at drivers ear (ICOMIA 39‑94) dBA 84.5
Tiller handle vibration (ICOMIA 38‑94) m/s² 2.58
eng 17
GENERAL INFORMATION
The engine‑rated horsepower is a direct relation to the engine's RPM. An
engine with too large of a propeller will have a further loss of horsepower and
subsequent decrease in boat speed. This secondary loss of RPM and boat
speed can be regained by switching to a smaller pitch propeller that allows the
engine to run at recommended RPM.
For boaters to realize optimum engine performance under changing weather
conditions, it is essential the engine has the proper propeller to allow it to
operate at, or near, the top end of the recommended maximum RPM range at
wide‑open throttle with a normal boat load. Not only does this allow the engine
to develop full power, but equally important, the engine will be operating in an
RPM range that discourages damaging detonation. This enhances overall
reliability and durability of the engine.
BOTTOM OF BOAT
For maximum speed, a boat bottom should be nearly a flat plane where it
contacts the water and particularly straight and smooth in fore and aft direction.
• Hook: Exists when bottom is concave in fore and aft direction when
viewed from the side. When boat is planing, hook causes more lift on
bottom near transom and allows bow to drop, thus greatly increasing
wetted surface and reducing boat speed. Hook frequently is caused by
supporting boat too far ahead of transom while hauling on a trailer or
during storage.
• Rocker: The reverse of hook and much less common. Rocker exists if
bottom is convex in fore and aft direction when viewed from the side, and
boat has strong tendency to porpoise.
• Surface roughness: Moss, barnacles, etc., on boat or corrosion of
outboard's gear housing increase skin friction and cause speed loss.
Clean surfaces when necessary.
18 eng
GENERAL INFORMATION
WATER ABSORPTION
It is imperative that all through‑the‑hull fasteners be coated with a quality
marine sealer at time of installation. Water intrusion into the transom core
and/or inner hull will result in additional boat weight (reduced boat
performance), hull decay, and eventual structural failure.
CAVITATION
Cavitation occurs when water flow cannot follow the contour of a fast‑moving
underwater object, such as a gear housing or a propeller. Cavitation increases
propeller speed while reducing boat speed. Cavitation can seriously erode the
surface of the gear housing or the propeller. Common causes of cavitation are:
• Weeds or other debris snagged on the propeller
• Bent propeller blade
• Raised burrs or sharp edges on the propeller
DETONATION
Detonation in a 4‑cycle engine resembles the pinging heard in an automobile
engine. It can be otherwise described as a tin‑like rattling or plinking sound.
Detonation is the explosion of the unburned fuel/air charge after the spark plug
has fired. Detonation creates severe shock waves in the engine. These shock
waves often find or create a weakness: the dome of a piston, cylinder head or
gasket, piston rings or piston ring lands, piston pin, and roller bearings.
A few of the most common causes of detonation in a marine 4‑cycle application
are as follows:
• Over‑advanced ignition timing
• Use of low octane gasoline
• Propeller pitch too high: engine RPM below recommended maximum
range
• Lean fuel mixture at, or near, wide‑open throttle
eng 19
GENERAL INFORMATION
• Spark plugs: heat range too hot, incorrect reach, cross‑firing
• Deteriorated or inadequate engine cooling system
• Combustion chamber deposits: result in higher compression ratio
Detonation usually can be prevented if:
• The engine is correctly set up
• Regular maintenance is scheduled
PROPELLER SELECTION
IMPORTANT: The engines covered in this manual are equipped with an RPM
rev‑limiter that is set to an upper RPM limit. This limit, which is slightly above
the normal operating range of the engine, helps prevent damage from
excessive engine RPM. Once the RPM returns to the recommended operating
RPM range, normal engine operation resumes.
The boat manufacturer and the selling dealer are responsible for equipping the
power package with the correct propeller. Refer to Mercury Marine's web page
https://www.mercurymarine.com/en/us/propellers/selector/#/step‑one.
Select a propeller that will allow the engine power package to operate at or
near the top end of the recommended WOT operating RPM range with a
normal load.
If full‑throttle operation is below the recommended range, the propeller must be
changed to prevent loss of performance and possible engine damage. On the
other hand, operating an engine above the recommended operating RPM
range will cause higher than normal wear and damage.
After initial propeller selection, the following common problems may require that
the propeller be changed to a lower pitch.
• Warmer weather and greater humidity cause a loss of RPM.
• Operating in a higher elevation causes a loss of RPM.
• Operating with a dirty boat bottom causes a loss of RPM.
• Operating with increased load (additional passengers, pulling skiers)
causes a loss of RPM.
For better acceleration, such as is needed for waterskiing, use the next lower
pitch propeller. When not pulling skiers, do not operate at full throttle when
using the lower pitch propeller.
20 eng
INSTALLATION
Boat Horsepower Capacity
! WARNING
Exceeding the boat's maximum horsepower rating can cause serious injury
or death. Overpowering the boat can affect boat control and flotation
characteristics or break the transom. Do not install an engine that exceeds
the boat's maximum power rating.
Do not overpower or overload your boat. Most boats will carry a required
capacity plate indicating the maximum acceptable power and load as
determined by the manufacturer following certain federal guidelines. If in doubt,
contact your dealer or the boat manufacturer.
The remote control connected to the outboard must be equipped with a start in
neutral only protection device. This prevents the engine from starting in gear.
eng 21
INSTALLATION
Low Permeation Fuel Hose Requirement
Required for outboards manufactured for sale, sold, or offered for sale in the
United States.
• The Environmental Protection Agency (EPA) requires that any outboard
manufactured after January 1, 2009, must use low permeation fuel hose
for the primary fuel hose connecting the fuel tank to the outboard.
• Low permeation hose is USCG Type B1‑15 or Type A1‑15, defined as not
exceeding 15 g/m²/24 h with CE 10 fuel at 23 °C as specified in SAE J
1527 ‑ marine fuel hose.
62883
Installing Outboard
BOAT TRANSOM HEIGHT REQUIREMENT
Measure the transom height of your boat. The boat bottom should be aligned or
be within 25 mm (1 in.) above the anti‑ventilation plate of the outboard.
a a - Anti‑ventilation plate
27151
22 eng
INSTALLATION
INSTALLING OUTBOARD ON TRANSOM
! WARNING
Failure to correctly fasten the outboard could result in the outboard propelling
off the boat transom resulting in property damage, serious injury, or death.
Before operation, the outboard must be correctly installed with the required
mounting hardware.
This product must be secured to the transom with the required mounting
hardware. If the outboard strikes an underwater object, the required mounting
hardware prevents the outboard from propelling off the transom. A decal on the
swivel bracket reminds the installer of the potential hazard.
WARNING
52375
27005
28501
eng 23
INSTALLATION
3. To prevent a loss of the outboard, secure the outboard to the transom
with the supplied mounting hardware. Use a 7.9 mm (5/16 in.) drill bit to
bore the holes into the transom. Use the transom bracket mounting holes
for the alignment guide. Secure the bolts with flat washers and locknuts.
Apply marine waterproofing sealer in the holes and around the bolts to
make the installation water tight. Tighten the bolts to the specified torque.
c a c
b b
a
63143
63141
28722
Tube Ref
Description Where Used Part No.
No.
24 eng
INSTALLATION
4. Thread the steering cable seal onto the end of the tilt tube.
b
63262
! WARNING
Improper fasteners or improper installation procedures can result in
loosening or disengagement of the steering link rod. This can cause a
sudden, unexpected loss of boat control, resulting in serious injury or death
due to occupants being thrown within or out of the boat. Always use required
components and follow instructions and torque procedures.
Assemble the steering link rod to the steering cable with a flat washer and
nylon insert locknut. Tighten the locknut until it seats, then back nut off 1/4 turn.
eng 25
INSTALLATION
Assemble the steering link rod to the engine with bolt, locknut, spacer, and flat
washers. Tighten the locknut to the specified torque.
b d
e
c
b b
a
f
63289
a- Bolt
b- Flat washer
c- Spacer
d- Nylon insert locknut
e- Steering bracket
f- Nylon insert locknut ‑ tighten until it seats, then back off 1/4 turn
26 eng
INSTALLATION
3. Loosen, but do not remove the screw that secures the cowl latch to the
driveshaft housing covers.
63041
4. Loosen the seven screws that secure the starboard driveshaft cover, and
remove the cover.
63039
Installation
Install the starboard cover after the shift and throttle cables are installed.
1. Position the starboard cover on the driveshaft housing and secure it with
seven screws.
2. Tighten the seven starboard‑side screws and the cowl latch screw to the
specified torque.
eng 27
INSTALLATION
Description Nm lb‑in. lb‑ft
Driveshaft housing cover and cowl
6 53 –
latch screws (11)
3. Attach the cowl seal.
4. Position the top cowl and secure it with the cowl latch.
6098
28 eng
INSTALLATION
4. Adjust the cable barrel so the center mark on the cable is aligned with the
end guide when the cable barrel is placed in the barrel receptacle.
b
d
c
63123
a- Bow‑tie retainer
b- Flat washer
c- Shift cable
d- Cable barrel
eng 29
INSTALLATION
1. Verify the throttle actuator timing mark is aligned with the timing mark on
the bracket. Adjust the throttle link if necessary to achieve proper
alignment.
b
c
63126
2. Locate the center point of the slack or lost motion that exists in the throttle
cable as follows:
a. Move the remote control handle from neutral into forward and advance
the handle to full speed position. Slowly return the handle back to
neutral. Place a mark (a) on the cable next to the end guide.
b. Move the remote control handle from neutral into reverse and advance
the handle to full speed position. Slowly return the handle back to
neutral. Place a mark (b) on the cable next to the end guide.
30 eng
INSTALLATION
c. Make a center mark (c), midway between marks (a and b). Align the
end guide with this center mark when installing the cable onto the
engine.
6098
3. Attach the throttle cable end guide to the throttle lever with a washer and
bow‑tie retainer.
4. Adjust the cable barrel so the installed throttle cable will maintain
alignment.
5. Position the throttle cable into the barrel receptacle.
a c d
b 63129
a- Bow‑tie retainer
b- Flat washer
c- Throttle cable
d- Cable barrel
eng 31
INSTALLATION
6. Install the cable barrel retainer and secure with the screw. Tighten the
screw to the specified torque.
63131
63133
32 eng
INSTALLATION
2. Install the egress grommet.
a- Throttle cable
b- Shift cable
c- Battery cables
d- 14‑pin harness
a
b c d
63135
3. Install the starboard driveshaft housing cover. Carefully align the egress
grommet while installing the driveshaft housing cover. Be certain to
tighten all screws to the specified torque.
63136
eng 33
INSTALLATION
3. Loosen the nuts securing the throttle cables to the bracket.
a
b
64613
4. Remove the top cable from the bracket and the throttle drum.
a
64614
a - Throttle drum
b - Bracket
34 eng
INSTALLATION
5. Remove the lower cable from the throttle drum and bracket.
64615
Lower cable
6. Install the cable with the flag onto the throttle drum lower guide and
bracket.
7. Install the cable without the flag onto the throttle drum top guide and
bracket.
64616
eng 35
INSTALLATION
8. Rotate the throttle grip so the idle alignment mark is to the left of the idle
alignment mark on the tiller handle.
64617
9. Push on the top cable threaded end while observing the tiller handle idle
alignment marks. When the marks are aligned, thread the nut that is on
the right side up to the bracket. Thread the nut on the left side up to the
bracket finger‑tight.
64618
36 eng
INSTALLATION
10. Push on the lower cable threaded end while observing the throttle drum.
When the throttle drum moves, the cable is too tight. Apply less tension
and thread the lower cable nut that is on the right side up to the bracket.
Thread the nut on the left side up to the bracket finger‑tight.
b
64619
11. Rotate the throttle grip to wide‑open throttle (WOT) and release the grip.
The marks should be aligned. If they are not aligned, rotate the grip to
align the marks. There should be no resistance when turning the grip to
align the marks.
12. Tighten the top cable nuts. Ensure the position of the cable does not
change on the bracket.
eng 37
INSTALLATION
13. Verify the throttle drum idle stop is contacting the idle stop on the bracket
when the idle marks on the tiller handle and grip are aligned.
a b
64620
14. Rotate the throttle grip to WOT and back to idle several times. The idle
marks must be aligned and the throttle drum idle stop must be contacting
the idle stop on the bracket.
15. Rotate the throttle grip to the WOT position and observe the throttle drum.
The throttle drum WOT stop should contact the stop on the bracket. If
necessary, thread the nut on the right side of the lower cable more toward
the bracket. Tighten the nuts on the lower cable.
38 eng
INSTALLATION
IMPORTANT: There should be a slight amount of cable slack on the upper
cable when the throttle is at WOT.
64623
16. Rotate the throttle grip to WOT and back to idle several times, checking to
ensure the throttle drum stop is contacting the bracket stop.
17. After the cables are adjusted correctly, apply 2‑4‑C with PTFE onto the
exposed cables, including the cable barrel and throttle drum guide.
Tube Ref
Description Where Used Part No.
No.
18. Align the cowl egress grommet, install the driveshaft housing cover, and
secure the cowl with the screws. Tighten the screws to the specified
torque. Refer to Driveshaft Housing Cover Removal and Installation.
eng 39
INSTALLATION
Battery Connections
CONNECTING OUTBOARD BATTERY CABLES
First, connect the red battery cable to the (+) positive battery terminal and then
connect the black battery cable to the (–) negative battery terminal.
DISCONNECTING OUTBOARD BATTERY CABLES
First, disconnect the black battery cable from the (–) negative terminal and then
disconnect the red battery cable from the (+) positive terminal.
27158
40 eng
TRANSPORTING
Aquatic Invasive Species (AIS)
STOP AQUATIC HITCHHIKERS!™
Be A Good Steward. Clean. Drain. Dry.
68805
For additional information, visit StopAquaticHitchhikers.org.
AIS and their spread can detrimentally impact the boating experience and the
future of the boating lifestyle. Reducing the spread of AIS has led to significant
national efforts to inspect boats moving between water bodies or across state
and federal boundaries and could lead to delayed or denied access if AIS are
suspected or found on board.
AIS include plant life such as Eurasian watermilfoil and water hyacinth, and
animals such as spiny water flea, quagga, and zebra mussels. AIS may vary in
size from microscopic, to easily visible to the naked eye, and can live in
residual water or mud. These species damage ecosystems and negatively
impact fishing by depleting natural food resources, altering the water
environment, and changing the structure of the ecosystem.
The impact of AIS has already resulted in the limiting of boating access to
many waterways throughout North America, the closure of public boat ramps,
and the reduction of availability for fishing and boating across the United
States. Many federal, state, and local agencies have enacted laws and
regulations for inspections, permits, launch availability, and water access for
vessels entering public waterways.
Boats and associated equipment are major contributors to the spread of AIS.
Boats that have come into contact with AIS can become a means of
transportation through attachment and entrapment.
You should be aware that water passes in and out of the space under the lower
cowls on your engine during normal operation of the boat. When flushing and
cleaning your boat to control the spread of AIS, pay attention to this space by
directing flushing water into the spaces under the lower cowl. The engine
cooling system can be flushed by operating the engine with the appropriate
flushing attachment and introducing heated water to the engine.
For more information about the control of AIS in your area, please contact your
area wildlife conservation office or local governmental natural resources office.
eng 41
TRANSPORTING
3. Carry, transport, or store the outboard in an upright position, horizontal
with the front of the engine facing up (tiller handle facing up), or on the
port side.
63254
Upright position
• The port side lower cowl has two bumpers to help reduce damage to
the cowl when the engine is stored in the laying down position. Storing
the engine on the port side will prevent oil from draining out of the
crankcase into the cylinders or crankcase ventilation system. There
are bumpers on the aft side of the cowl also.
63255
Trailering Boat/Outboard
Trailer your boat with the outboard tilted down in a vertical operating position.
42 eng
TRANSPORTING
If additional ground clearance is required, the outboard should be tilted up
using an accessory outboard support device. Refer to your local dealer for
recommendations. Additional clearance may be required for railroad crossings,
driveways, and trailer bouncing.
32176
IMPORTANT: Do not rely on the power tilt system or the tilt support lever to
maintain proper ground clearance for trailering. The outboard tilt support lever
is not intended to support the outboard for trailering.
Shift the outboard into reverse gear. This prevents the propeller from spinning.
eng 43
FUEL AND OIL
Fuel Requirements
IMPORTANT: Use of improper gasoline can damage your engine. Engine
damage resulting from the use of improper gasoline is considered misuse
of the engine and will not be covered under the limited warranty.
FUEL RATINGS
Mercury outboard engines will operate satisfactorily with any major brand of
unleaded gasoline that meets the following specifications:
USA and Canada ‑ A posted pump octane rating of 87 (R+M)/2, minimum, for
most models. Premium gasoline 91 (R+M)/2 octane is also acceptable for most
models. Do not use leaded gasoline.
Outside USA and Canada ‑ A posted pump octane rating of 91 RON,
minimum, for most models. Premium gasoline (95 RON) is also acceptable for
all models. Do not use leaded gasoline.
USING REFORMULATED (OXYGENATED) GASOLINE (USA ONLY)
Reformulated gasoline is required in certain areas of the USA and is
acceptable for use in your Mercury Marine engine. The only oxygenate
currently in use in the USA is alcohol (ethanol, methanol, or butanol).
GASOLINE CONTAINING ALCOHOL
Bu16 Butanol Fuel Blends
Fuel blends of up to 16.1% butanol (Bu16) that meet the published Mercury
Marine fuel rating requirements are an acceptable substitute for unleaded
gasoline. Contact your boat manufacturer for specific recommendations on
your boat's fuel system components (fuel tanks, fuel lines, and fittings).
Methanol and Ethanol Fuel Blends
IMPORTANT: The fuel system components on your Mercury Marine engine will
withstand up to 10% alcohol (methanol or ethanol) content in the gasoline. Your
boat's fuel system may not be capable of withstanding the same percentage of
alcohol. Contact your boat manufacturer for specific recommendations on your
boat's fuel system components (fuel tanks, fuel lines, and fittings).
Be aware that gasoline containing methanol or ethanol may cause increased:
• Corrosion of metal parts
• Deterioration of rubber or plastic parts
• Fuel permeation through the rubber fuel lines
• Likelihood of phase separation (water and alcohol separating from the
gasoline in the fuel tank)
44 eng
FUEL AND OIL
! WARNING
Fuel leakage is a fire or explosion hazard, which can cause serious injury or
death. Periodically inspect all fuel system components for leaks, softening,
hardening, swelling, or corrosion, particularly after storage. Any sign of
leakage or deterioration requires replacement before further engine
operation.
eng 45
FUEL AND OIL
The fuel demand valve has a manual release. The manual release can be used
(pushed in) to open (bypass) the valve in case of a fuel blockage in the valve.
b a - Fuel cap
a b - Manual vent screw
c - Tab lock
c
46290
IMPORTANT: Contents may be under pressure. Rotate the fuel cap 1/4 turn to
relieve pressure before opening.
46 eng
FUEL AND OIL
1. Open the manual vent screw on top of the fuel cap.
2. Turn the fuel cap until it contacts the tab lock.
3. Press down on the tab lock. Rotate the fuel cap 1/4 turn to relieve the
pressure.
4. Press down on the tab lock again and remove the cap.
DIRECTIONS FOR USING THE PRESSURIZED PORTABLE FUEL TANK
1. When installing the fuel tank cap, turn the cap to the right until you hear a
click. This signals that the fuel cap is fully seated. A built‑in device
prevents overtightening.
2. Open the manual vent screw on top of the cap for operation and cap
removal. Close the manual vent screw for transportation.
3. For fuel hoses that have quick disconnects, disconnect the fuel line from
the engine or fuel tank when not in use.
4. Follow Filling Fuel Tank instructions for fueling.
Fill the fuel tanks outdoors away from heat, sparks, and open flames.
Remove the portable fuel tanks from the boat to fill them.
Always stop the engine before filling the tanks.
Do not completely fill the fuel tanks. Leave approximately 10% of the tank
volume unfilled. Fuel will expand in volume as its temperature rises and can
leak under pressure if the tank is completely filled.
PORTABLE FUEL TANK PLACEMENT IN THE BOAT
Place the fuel tank in the boat so the vent is higher than the fuel level under
normal boat operating conditions.
eng 47
FUEL AND OIL
IMPORTANT: The use of nondetergent oils, multiviscosity oils (other than
Mercury or Quicksilver NMMA FC‑W certified oil or a major brand NMMA FC‑W
certified oil), synthetic oils, low quality or oils that contain solid additives are not
recommended.
Specifications
Engine Oil
+120 +49
25W-40
+100 +38
10W-30 +80 +27
+60 +16
+40 +4
+20 -7
0 -18
F C
48 eng
FUEL AND OIL
IMPORTANT: Do not try to fill the oil level to the top of the operating range
(upper hole). Oil level is correct as long as it appears in the operating range
between the upper and lower hole.
62881
5. If the oil level is below the operating range (lower hole), remove the oil fill
cap and add approximately 200 ml (7 fl oz) of specified outboard motor
oil. Allow a few minutes for the added oil to drain to the oil sump and
check the dipstick. Repeat the process until oil level is in the operating
range between the upper and lower holes. Do not try to fill to the upper
end of the operation range (upper hole).
NOTE: Under certain conditions, the operating temperature of 4‑stroke
outboard engines may not get hot enough to evaporate the normal fuel and
moisture that accumulate in the crankcase. These conditions include operating
at idle for long periods, repeated short trips, slow speed or quick stop‑and‑go
operation, and operating in cooler climates. This additional fuel and moisture
that collects in the crankcase eventually ends up in the oil sump and will add
to the total volume of oil that appears on the dipstick reading. This increase in
oil volume is known as oil dilution. Outboard engines can typically handle large
amounts of oil dilution without causing durability problems. However, to ensure
extended life of the outboard engine, Mercury recommends that the oil and
filter be changed regularly following the oil change interval and using the
recommended oil quality. It is further recommended that if your outboard is
operated frequently in the conditions described above, that more frequent oil
change intervals be considered.
6. Push the dipstick back in all the way.
7. Install the oil fill cap hand‑tight.
eng 49
FUEL AND OIL
8. Install top cowl.
50 eng
FEATURES AND CONTROLS
Tiller Handle Features
• A decal on the tiller handle is a quick reference guide for starting a cold or
hot engine.
• Throttle grip friction knob ‑ Turn the friction knob to set and maintain the
throttle at desired speed. Turn the knob clockwise to increase the friction
or turn the knob counterclockwise to decrease the friction.
b
a
c
63078
• Shift lever ‑ The outboard has three gear shift positions to provide
operation: forward (F), neutral (N), and reverse (R).
N
F R
63077
eng 51
FEATURES AND CONTROLS
• Tiller handle adjustment knob ‑ Turn the adjustment knob to raise or lower
the tiller handle in its operating position.
a b
63082
63908
63909
• Tiller handle yaw ‑ The tiller handle yaw allows the operator to change the
angle of the handle up to 18° left or right of center. Each increment
demarcation is 6°.
a. Remove the rubber boot covering the clamp screw nut.
52 eng
FEATURES AND CONTROLS
b. Loosen the 15 mm nut so it is almost completely off.
63258
c. Loosen the 6 mm Allen socket head pivot screw.
63259
eng 53
FEATURES AND CONTROLS
d. Lift the clamp with your fingers and rotate the tiller handle to the
desired angle.
b a - Clamp
a b - Clamp screw nut
c - Center demarcation
63260
e. Tighten the clamp screw nut to the specified torque and install the
rubber boot.
54 eng
FEATURES AND CONTROLS
NOTE: A spare lanyard stop switch clip is stored on the tiller handle.
c
63083
63084
eng 55
FEATURES AND CONTROLS
• Throttle grip ‑ Controls the engine speed. Align the throttle grip with the
idle mark on the tiller handle when starting or shifting into or out of gear.
Twist the throttle grip to increase the engine speed.
63086
• Power tilt switch (if equipped) ‑ Tiller handle models equipped with power
tilt have a switch located on the underside of the tiller handle. Press the
switch to raise (UP) or lower (DN) the engine.
63906
• Electric start button (electric start models) ‑ Press the button to start the
engine, if equipped.
56 eng
FEATURES AND CONTROLS
• Warning light ‑ Warns the operator when the engine has low oil pressure,
over temperature, exceeding the RPM limit, or sensor faults. Refer to
Warning System in this section.
a
b
63085
a - Warning light
b - Electric start button (electric start models)
a
a
c
c d c
58240
a- Tilt switch
b- Ignition key switch—OFF, ON, START
c- Throttle only button
d- Lanyard stop switch
• Tilt switch ‑ Used to trim the drive during operation or raise the drive for
trailering, launching, beaching, or shallow water operation.
eng 57
FEATURES AND CONTROLS
• Throttle only button ‑ The throttle only button allows throttle
advancement without shifting the engine. The throttle only button
disengages the shifting mechanism from the control handle. The throttle
only button can be pressed and held in only when the remote control
handle is in the neutral position. While holding the throttle only button in,
move the throttle handle forward to assist in starting the engine.
• Lanyard stop switch (if equipped) ‑ The purpose of a lanyard stop
switch is to shut down the engine when the operator moves far enough
away from the operator's position to activate the switch. A lanyard stop
switch can be installed as an accessory, generally on the dashboard or
side adjacent to the operator's position.
• Control handle ‑ Operation of the shift and throttle is controlled by the
movement of the control handle. Push the control handle forward from
neutral with a quick firm motion to the first detent for forward gear.
Continue pushing forward to increase speed. Pull the control handle back
from neutral with a quick firm motion to the first detent for reverse gear.
Continue pulling back to increase speed.
IMPORTANT: Forcing the shift mechanism while the engine is not operating
can result in product damage.
GEAR SHIFTING
IMPORTANT: Observe the following:
• Never shift the outboard into or out of gear unless the engine speed
is at idle. Shifting at higher than engine idle speed could cause
damage to the gearcase.
• Do not shift the outboard into reverse when the forward motion of
the boat is greater than a no wake speed. Shifting into reverse at
higher boat speeds could cause the engine to stall, and in some
situations, this could cause water to be drawn into the cylinders,
resulting in severe engine damage.
• Do not shift the outboard into reverse when the engine is not
running. Damage to the shift linkage could occur.
• Your power package has three gear shift positions to provide operation:
forward (F), neutral (N), and reverse (R).
• When shifting, always stop at the neutral position and allow the engine
speed to return to idle.
• Always shift into gear with a quick motion.
58 eng
FEATURES AND CONTROLS
• After shifting into gear, advance the lever further to increase speed.
N
F R
58239
General Features
• Steering friction adjustment (if equipped) ‑ Adjust this lever to achieve the
desired steering friction (drag) on the tiller handle. Move the lever to the
starboard to increase the friction, or move the lever to the port to
decrease the friction. A quick reference decal is located on the transom
clamp.
! WARNING
Insufficient friction adjustment can cause serious injury or death due to loss
of boat control. When setting the friction adjustment, maintain sufficient
steering friction to prevent the outboard from steering into a full turn if the
tiller handle or steering wheel is released.
c d
63097
eng 59
FEATURES AND CONTROLS
• Cooling water intake ‑ The outboard water intake for cooling the engine is
located on both sides of the gear housing. If overheating is encountered,
this area should be inspected first for debris blocking the intake.
63098
• Water pump indicator ‑ Water spray from this location indicates the water
pump is pumping cooling water up to the engine. If there is no water
spray, inspect the water intake on the gear housing.
62870
60 eng
FEATURES AND CONTROLS
• Tilt pin ‑ Set the vertical operating angle on the outboard. Refer to Setting
the Operation Angle of the Outboard.
63093
15920
eng 61
FEATURES AND CONTROLS
4. Take hold of the top cowl grip and tilt the outboard all the way up until it
locks in place.
32150
62 eng
FEATURES AND CONTROLS
5. To release the outboard out of shallow water drive, position the tilt lever to
the locked tilt release position. Slightly lift up the outboard, and gently
lower it down.
32151
eng 63
FEATURES AND CONTROLS
Arrange passengers and load in the boat so the weight is distributed evenly.
c
15927
Consider the following lists carefully when adjusting the operating angle of your
outboard.
Adjusting the outboard close to the boat transom can:
• Lower the bow
• Result in quicker planing off, especially with a heavy load or a stern heavy
boat
• Generally improve the ride in choppy water
• Increase steering torque or pull to the right (with the normal right‑hand
rotation propeller)
• In excess, can lower the bow of some boats to a point where they begin to
plow with their bow in the water while on plane. This can result in an
unexpected turn in either direction (called bow steering or oversteering) if
any turn is attempted, or if a significant wave is encountered.
Adjusting the outboard away from the boat transom can:
• Lift the bow out of the water
• Generally increase top speed
• Increase clearance over submerged objects or a shallow bottom
• Increase steering torque or pull to the left at a normal installation height
(with the normal right‑hand rotation propeller)
64 eng
FEATURES AND CONTROLS
• In excess, can cause boat porpoising (bouncing) or propeller ventilation
a
c
b
63100
63906
eng 65
FEATURES AND CONTROLS
TILTING THE OUTBOARD TO FULL UP POSITION
To tilt the outboard, shut off the engine and press the tilt switch to the up
position. The outboard will tilt up until the switch is released or it reaches its
maximum tilt position.
1. Engage the tilt support lever by rotating the lever down.
2. Lower the outboard to rest on the tilt support lever.
3. Disengage the tilt support lever by slightly tilting up the outboard and
releasing the tilt support bracket. Lower the outboard.
31919
! WARNING
Avoid injury or death from loss of steering control. ProKicker centering straps
prevent the outboard from turning when tilted up. If using a steering tie bar to
a second outboard, disconnect the steering tie bar to allow steering of the
second outboard before operating the boat.
a
32201
66 eng
FEATURES AND CONTROLS
SHALLOW WATER OPERATION
When operating your boat in shallow water, the outboard can be tilted up to a
higher tilt angle. Reduce engine speed to idle for tilting. Operate the outboard
at slow speed while tilted up for shallow water operation. Keep the cooling
water intake holes submerged in the water and continue to check for water
discharge from the water pump indicator.
32193
31967
eng 67
FEATURES AND CONTROLS
The adjustment of the tilt‑in stop pins will set the vertical operating angle of
your outboard. Proper adjustment allows the boat to run stable, achieve
optimum performance, and minimize steering effort.
32192
NOTE: Refer to the following lists when adjusting the operating angle of your
outboard.
The tilt‑in stop pins should be adjusted so the outboard is positioned to run
perpendicular to the water when the boat is running at full speed. This allows
the boat to be driven parallel to the water.
Arrange passengers and load in the boat so the weight is distributed evenly.
c
64201
68 eng
FEATURES AND CONTROLS
Consider the following lists carefully when adjusting the operating angle of your
outboard.
Adjusting the outboard close to the boat transom can:
• Lower the bow
• Result in quicker planing off, especially with a heavy load or a stern heavy
boat
• Generally improve the ride in choppy water
• Increase steering torque or pull to the right (with the normal right‑hand
rotation propeller)
• In excess, can lower the bow of some boats to a point where they begin to
plow with their bow in the water while on plane. This can result in an
unexpected turn in either direction (called bow steering or oversteering) if
any turn is attempted, or if a significant wave is encountered.
Adjusting the outboard away from the boat transom can:
• Lift the bow out of the water
• Generally increase top speed
• Increase clearance over submerged objects or a shallow bottom
• Increase steering torque or pull to the left at a normal installation height
(with the normal right‑hand rotation propeller)
• In excess, can cause boat porpoising (bouncing) or propeller ventilation
Warning System
WARNING HORN LOCATION
A warning horn is located near the front of the engine, under the cowl. On
remote control models, an additional warning horn is located inside the remote
control or connected to the ignition key switch.
62873
eng 69
FEATURES AND CONTROLS
WARNING SYSTEM OPERATION
The warning horn will emit either a continuous beep or intermittent short beeps
and engine speed will be limited. This will alert the operator and help identify
the following listed situations.
20 HP Warning System Operation
Warning
Function Warning Horn Description RPM Limit
Lamp
Start up One second System test None
Engine
Overheat
Continuous for overheat
On
Low oil six seconds Low oil
pressure pressure
2800
Six flashes
Six beeps repeats Engine sensor
Sensor error
no repeats every five fault
minutes
Engine
Engine speed misfire
Overspeed * None
too high may be
noticed
Warning
Function Warning Horn Description RPM Limit
Lamp
Start up One second System test None
Engine
Overheat
Continuous for overheat
On
Low oil six seconds Low oil
pressure pressure 2800
Six flashes
Six beeps Engine sensor
Sensor error repeats every
no repeats fault
five minutes
Engine
Engine speed misfire
Overspeed * None
too high may be
noticed
Six flashes
Six beeps Restrictor
Restrictor repeats every 2800
no repeats missing
five minutes
70 eng
FEATURES AND CONTROLS
* Refer to the Specifications table for RPM limits.
ENGINE OVERHEAT
If the engine overheats, immediately reduce throttle speed to idle. Shift the
outboard into neutral and check for a steady stream of water coming out of the
water pump indicator hole.
62870
eng 71
FEATURES AND CONTROLS
• Tilting the outboard out beyond a vertical position
• Cavitation of the propeller due to rough water or obstruction in the boat
hull
When the engine overspeed limiter is activated, the engine timing will be
momentarily reduced to decrease the engine speed. Excessive overspeed will
result in the momentary removal of ignition to prevent operation above the RPM
limit. Refer to General Information ‑ Specifications.
72 eng
OPERATION
Prestarting Check List
• Operator knows safe navigation, boating, and operating procedures.
• An approved personal flotation device of suitable size for each person
aboard and readily accessible (it is the law).
• A ring type life buoy or buoyant cushion designed to be thrown to a
person in the water.
• Know your boat's maximum load capacity. Look at the boat capacity plate.
• Fuel supply OK.
• Arrange passengers and load in the boat so the weight is distributed
evenly and everyone is seated in a proper seat.
• Tell someone where you are going and when you expect to return.
• It is illegal to operate a boat while under the influence of alcohol or drugs.
• Know the waters and area you will be boating; tides, currents, sand bars,
rocks, and other hazards.
• Make inspection checks listed in Maintenance ‑ Inspection and
Maintenance Schedule.
eng 73
OPERATION
Operating Outboard as an Auxiliary Engine
If the outboard is used as an auxiliary engine, stop the engine and tilt the
outboard out of the water when using the main power source.
IMPORTANT: The outboard must be restrained from bouncing while operating
the boat using the main power source. Bouncing can damage the outboard and
boat transom.
Prestarting Instructions
1. Connect the remote fuel line to the outboard. Ensure the connector is
snapped into place.
63102
74 eng
OPERATION
2. Check the engine oil level.
62881
NOTICE
Without sufficient cooling water, the engine, the water pump, and other
components will overheat and suffer damage. Provide a sufficient supply of
water to the water inlets during operation.
3. Make sure the cooling water intake is submerged.
26837
eng 75
OPERATION
4. Tiller handle models with manual or electric start, have a quick reference
decal on the tiller handle that shows the sequence for starting the engine.
Use this quick reference for cold or hot starting.
b
a
c
63078
76 eng
OPERATION
1. Open the fuel tank vent screw on the manual venting type tanks.
b a - Fuel cap
a b - Manual vent screw
c - Tab lock
c
46290
2. Position the fuel line primer bulb so the arrow on the side of the bulb is
pointing up. Squeeze the fuel line primer bulb several times until it feels
firm.
IMPORTANT: To prevent engine flooding, do not squeeze the primer bulb
after the engine has warmed up.
27348
3. Insert the lanyard clip into the stop switch. This is the RUN position.
c
63083
eng 77
OPERATION
4. Verify the shift handle is in the neutral (N) position.
N
F R
63077
63086
6. Manual starting models ‑ Pull the starter rope slowly until you feel the
starter engage, then pull rapidly to crank the engine. Allow rope to return
slowly. Repeat until the engine starts.
IMPORTANT: Outboards with battery charging capabilities must not be
operated with battery cables disconnected from the battery. Damage to the
charging system may result.
31954
7. Electric starting models ‑ Push the starter button and crank the engine.
Release button when the engine starts. Do not operate the starter motor
continuously for longer than ten seconds at a time. If the engine fails to
start, wait 30 seconds and try again.
78 eng
OPERATION
8. Flooded engine ‑ If the engine will not start, advance the throttle grip
slightly and attempt to start the engine. After the engine has started,
immediately reduce the throttle speed to idle.
9. Verify the warning light turns off.
NOTE: The warning light will remain illuminated for up to five seconds after the
outboard starts. If the light should stay on, refer to Features and Controls ‑
Warning System.
62873
10. Check for a steady stream of water flowing out of the water pump
indicator.
62870
IMPORTANT: If no water is coming out of the water pump indicator, stop the
engine and check the cooling water intake for obstruction. No obstruction may
indicate a water pump failure or blockage in the cooling system. These
conditions will cause the engine to overheat. Have the outboard checked by
your dealer. Operating the engine while overheated will cause serious engine
damage.
WARMING UP ENGINE
Before beginning operation, allow the engine to warm up at idling speed for
three minutes.
eng 79
OPERATION
1. Open the fuel tank vent screw on the manual venting type tanks.
b a - Fuel cap
a b - Manual vent screw
c - Tab lock
c
46290
2. Position the fuel line primer bulb so the arrow on the side of the bulb is
pointing up. Squeeze the fuel line primer bulb several times until it feels
firm.
27348
3. Set the lanyard stop switch to the RUN position. Refer to General
Information ‑ Lanyard Stop Switch.
19791
80 eng
OPERATION
4. Verify the remote control handle is in the neutral position.
63103
19804
62873
eng 81
OPERATION
7. Check for a steady stream of water flowing out of the water pump
indicator.
62870
IMPORTANT: If no water is coming out of the water pump indicator, stop the
engine and check the cooling water intake for obstruction. No obstruction may
indicate a water pump failure or blockage in the cooling system. These
conditions will cause the engine to overheat. Have the outboard checked by
your dealer. Operating the engine while overheated will cause serious engine
damage.
WARMING UP ENGINE
Before beginning operation, allow the engine to warm up at idling speed for
three minutes.
Gear Shifting
IMPORTANT: Observe the following:
• Never shift the outboard into or out of gear unless the engine speed
is at idle. Shifting at higher than engine idle speed could cause
damage to the gearcase.
• Do not shift the outboard into reverse when the forward motion of
the boat is greater than a no wake speed. Shifting into reverse at
higher boat speeds could cause the engine to stall, and in some
situations, this could cause water to be drawn into the cylinders,
resulting in severe engine damage.
• Do not shift the outboard into reverse when the engine is not
running. Damage to the shift linkage could occur.
82 eng
OPERATION
• Tiller handle models ‑ Your outboard has three gear shift positions to
provide operation: forward (F), neutral (N), and reverse (R). When
shifting, always stop at the neutral position and allow the engine speed to
return to idle.
N
F R
63077
• Remote control models ‑ Your outboard has three gear shift positions to
provide operation: forward (F), neutral (N), and reverse (R). When
shifting, always stop at the neutral position and allow the engine speed to
return to idle.
N
F R
58239
eng 83
OPERATION
Stopping the Engine
1. Remote control models ‑ Reduce the engine speed and shift the
outboard to the neutral position. Turn the ignition key to the "OFF"
position.
OFF
ON
START
26843
2. Tiller handle models ‑ Reduce the engine speed and shift the outboard
to the neutral position. Push in the engine stop button.
26776
84 eng
OPERATION
Emergency Starting Procedure
If the starter system fails, use the tools provided with the engine to remove the
recoil assembly to start the engine. Read the following procedure before
attempting to remove the recoil assembly.
! WARNING
The neutral‑speed‑protection device is inoperative when starting the engine
with the emergency starter rope. Set the engine speed at idle and the gear
shift in neutral to prevent the outboard from starting in gear.
1. Remove four short screws and washers securing the recoil assembly to
the engine.
63117
2. Pull the neutral interlock cable to disengage the neutral interlock cable
from the recoil housing.
eng 85
OPERATION
3. Lift the neutral interlock cable up and remove the neutral interlock cable
tension spring from the recoil housing.
a
b
63118
4. Remove one long and one medium length screw and washers securing
the air box to the engine.
c
b
63119
a - Long screw
b - Medium screw
c - Neutral interlock cable
86 eng
OPERATION
IMPORTANT: If the air box is rotated too far, or disengages from the throttle
body, a hose attached to the air box (hidden in the following illustration) could
disengage. This hose must be restored to its original location. If this hose is
not restored to its original location, the engine will not operate properly.
a
63120
6. Carefully remove the recoil starter assembly.
7. Install the medium length screw to retain the air box. Tighten the screw
securely.
63146
! WARNING
High voltage is present when starting or operating the engine. Do not touch
any ignition component, wiring, or spark plug lead when starting or
operating the engine.
eng 87
OPERATION
! WARNING
The exposed moving flywheel can cause serious injury. Keep your hands,
hair, clothing, tools, and other objects away from engine when starting or
running the engine. Do not attempt to reinstall the rewind starter or top cowl
when engine is running.
11. Place the starter rope knot into the flywheel notch and wind the rope
clockwise around the flywheel.
63121
88 eng
MAINTENANCE
Cleaning Care Recommendations
OUTBOARD CARE
To keep your outboard in the best operating condition, it is important that your
outboard receive the periodic inspections and maintenance listed in the
Inspection and Maintenance Schedule. We urge you to keep it maintained
properly to ensure the safety of you and your passengers, and retain its
dependability.
Record maintenance performed in the Maintenance Log at the back of this
book. Save all maintenance work orders and receipts.
Selecting Replacement Parts For Your Outboard
We recommend using original Mercury Precision or Quicksilver replacement
parts and Genuine Lubricants.
CLEANING GAUGES
IMPORTANT: Never use high‑pressure water to clean gauges.
Routine cleaning of the gauges is recommended to prevent a buildup of salt
and other environmental debris. Crystalized salt can scratch the gauge display
lens when using a dry or damp cloth. Ensure that the cloth has a sufficient
amount of fresh water to dissolve and remove salt or mineral deposits. Do not
apply aggressive pressure on the display lens while cleaning.
When water marks cannot be removed with a damp cloth, mix a 50/50 solution
of warm water and isopropyl alcohol to clean the display lens. Do not use
acetone, mineral spirits, turpentine type solvents, or ammonia based cleaning
products. The use of strong solvents or detergents may damage the coating,
the plastics, or the rubber keys on the gauges. If the gauge has a sun cover
available, it is recommended that the cover be installed when the unit is not in
use to prevent UV damage to the plastic bezels and rubber keys.
eng 89
MAINTENANCE
Routine cleaning of the remote control external surfaces is recommended to
prevent a buildup of salt and other environmental debris. Use a cloth towel
which has a sufficient amount of fresh water to dissolve and remove salt or
mineral deposits.
When water marks cannot be removed with a damp cloth, mix a 50/50 solution
of warm water and isopropyl alcohol to clean the remote control. Do not use
acetone, mineral spirits, turpentine type solvents, or ammonia based cleaning
products. The use of strong solvents or detergents may damage the coating,
the plastics, or the rubber components on the remote control.
90 eng
MAINTENANCE
EMISSION CERTIFICATION LABEL
An emission certification label, showing emission levels and engine
specifications directly related to emissions, is placed on the engine at the time
of manufacture.
E M I S SI ON CON T R O L
I N F O R MAT I O N M F I 2 0 x x a - Regulated emission
THIS ENGINE CONFORMS TO 2017
limit for the engine
CALIFORNIA AND U.S. EPA family
REGULATIONS FOR SPARK IGNITION
MARINE ENGINES. REFER TO
h b - Idle speed
OWNERS MANUAL FOR MAINTENANCE c - US EPA engine family
a JAN SPECIFICATIONS AND ADJUSTMENTS. JUL name
EPA/CA HC+NOx FEL: xx.x g/kWh d - Engine horsepower
b FEB
EPA CO FEL: xxx g/kWh
AUG
OWNER RESPONSIBILITY
The owner/operator is required to have routine engine maintenance performed
to maintain emission levels within prescribed certification standards.
The owner/operator is not to modify the engine in any manner that would alter
the horsepower or allow emission levels to exceed their predetermined factory
specifications.
eng 91
MAINTENANCE
AFTER EACH USE
• Flush the outboard cooling system with fresh water if operating in salt or
polluted water. Refer to Flushing the Cooling System.
• Wash off all salt deposits and flush out the exhaust outlet of the propeller
and gearcase with fresh water if operating in saltwater.
• If operating in saltwater, inspect the powerhead and powerhead
components for salt buildup. Refer to Cleaning Care
Recommendations.
EVERY 100 HOURS OF USE OR ONCE YEARLY, WHICHEVER
OCCURS FIRST
• Change engine oil and replace the oil filter. The oil should be changed
more often when the engine is operated under adverse conditions, such
as extended trolling. Refer to Engine Oil.
• Change the gear lubricant. Refer to Gearcase lubricant.
• Check water‑separating fuel filter for contaminants. Replace filter if
required. Refer to Fuel System.
• Remove the propeller and lubricate the propeller shaft. Refer to Propeller
Replacement.
• Check corrosion control anodes. Check more frequently when used in
saltwater. Refer to Corrosion Control Anodes and Continuity Wire.
• Drain and replace gearcase lubricant. Refer to Gearcase Lubricant.
• Inspect battery. Refer to Battery Inspection.
• Saltwater usage: Remove and inspect spark plugs for corrosion and
replace as necessary. Apply Anti‑Seize Compound only onto the threads
of spark plug prior to installation. Refer to Spark Plug Inspection and
Replacement.
Tube Ref
Description Where Used Part No.
No.
Anti-Seize
81 Spark plug threads 92-898101389
Compound
Tube Ref
Description Where Used Part No.
No.
Quickleen Engine &
Fuel System Fuel tank 8M0047931
Cleaner
• Check cowl seals to ensure seals are intact and not damaged.
• Check that the idle relief muffler is in place, if equipped.
• Inspect the thermostat visually for corrosion or a broken spring. Verify the
thermostat closes completely at room temperature—dealer service.
92 eng
MAINTENANCE
• Check the outboard mounting fasteners that secure the outboard to the
boat transom. Tighten the fasteners to the specified torque—dealer
service.
• Check tightness of bolts, nuts, and other fasteners—dealer service.
• Check for loose hose clamps and rubber boots on the air intake assembly
—dealer service.
• Lubricate the driveshaft splines—dealer item
EVERY 300 HOURS OF USE OR THREE YEARS
• Lubricate the throttle and shift cable with oil—tiller handle models.
• Verify the throttle and shift cables are properly adjusted.
• Check the power trim fluid. Refer to Checking Power Tilt Fluid.
• Lubricate all lubrication points. Lubricate more frequently when used in
saltwater. Refer to Lubrication Points.
• Replace the spark plugs. Refer to Spark Plug Inspection and
Replacement.
• Check the remote control cable adjustment, if applicable—dealer service.
• Inspect the timing belt—dealer service.
• Lubricate the splines on the upper driveshaft—dealer service.
• Check the wiring and connectors—dealer service.
• Replace the water pump impeller—dealer service.1.
BEFORE PERIODS OF STORAGE
• Refer to Storage section.
Flush the internal water passages of the outboard with fresh water after each
use in salt, polluted, or muddy water. This will help prevent a buildup of
deposits from clogging the internal water passages.
IMPORTANT: The engine must be run during flushing in order to open the
thermostat and circulate water through the water passages.
1. Remove the propeller. Refer to Propeller Replacement.
1. Replace the water pump impeller more often if overheating occurs or reduced water pressure is noted.
eng 93
MAINTENANCE
2. Remove the plug from the flush fitting, and attach a water hose. Turn on
the water to half of the maximum flow.
62842
Flush fitting
3. Start the engine and run it at idle speed in neutral shift position.
IMPORTANT: Do not run the engine above idle while flushing.
4. Check for a steady stream of water flowing out of the water pump
indicator hole. Continue flushing the outboard for 3–5 minutes, carefully
monitoring the water supply at all times.
5. Stop the engine, turn off the water, and remove the water hose.
6. Install the plug into the flush fitting.
7. Install the propeller.
94 eng
MAINTENANCE
2. Lift up the rear of the cowl and push it toward the front of the engine to
clear the front hook.
63227
INSTALLATION
1. Engage the front hook and position the cowl over the engine.
2. Lock the rear latch.
Battery Inspection
The battery should be inspected at periodic intervals to ensure proper engine
starting capability.
IMPORTANT: Read the safety and maintenance instructions which accompany
your battery.
1. Turn off the engine before servicing the battery.
2. Ensure the battery is secure against movement.
3. Battery cable terminals should be clean, tight, and correctly installed.
Positive to positive and negative to negative.
4. Ensure the battery is equipped with a nonconductive shield to prevent
accidental shorting of battery terminals.
Exterior Care
Your outboard is protected with a durable baked enamel finish. Clean and wax
often using marine cleaners and waxes.
eng 95
MAINTENANCE
Fuel System
FUEL SYSTEM PRECAUTIONS
! WARNING
Fuel is flammable and explosive. Ensure that the key switch is off and the
lanyard is positioned so that the engine cannot start. Do not smoke or allow
sources of spark or open flame in the area while servicing. Keep the work
area well ventilated and avoid prolonged exposure to vapors. Always check
for leaks before attempting to start the engine, and wipe up any spilled fuel
immediately.
Before servicing any part of the fuel system, stop the engine and disconnect
the battery. Drain the fuel system completely. Use an approved container to
collect and store fuel. Wipe up any spillage immediately. Material used to
contain spillage must be disposed of in an approved receptacle. Any fuel
system service must be performed in a well ventilated area. Inspect any
completed service work for sign of fuel leakage.
96 eng
MAINTENANCE
3. Pull the filter assembly—including the rubber mount—off of the mounting
bracket on the engine, and swing the assembly over the edge of the
engine cowl.
63109
4. Loosen the threaded drain fitting approximately 2.5 turns and empty the
filter bowl's contents into an approved container. To protect the
environment, immediately clean up spilled fluids and dispose of according
to local laws and regulations.
NOTE: A drain hose can be temporarily installed onto the center drain port of
the drain fitting to assist emptying the contents into an approved container.
63110
Drain fitting
5. If installed, remove the drain hose and tighten the threaded drain fitting
securely.
6. Install the filter assembly onto the mounting bracket.
eng 97
MAINTENANCE
FUEL FILTER REPLACEMENT
Filter Removal
1. Pull the filter assembly—including the rubber mount—off of the mounting
bracket on the engine, and swing the assembly over the edge of the
engine cowl.
63109
a - Filter housing
a b - Rubber mount
c - Sight bowl
b
63111
4. Pull the filter element off the filter housing.
98 eng
MAINTENANCE
IMPORTANT: The filter is secured and sealed to the filter housing with an
O‑ring. The O‑ring may remain on the filter housing. The O‑ring should be
removed before installing the fuel filter.
63112
Fuel filter
Filter Installation
d e
a b c
63113
eng 99
MAINTENANCE
1. Install the fuel filter O‑ring seal into the fuel filter. Verify the O‑ring does
not have any folds or kinks.
63114
63115
4. Install the sight bowl O‑ring seal onto the sight bowl and place the red ring
into the sight bowl.
5. Install the sight bowl onto the filter housing hand‑tight.
100 eng
MAINTENANCE
6. Verify the rubber mount is properly aligned with the filter housing and
install the rubber mount.
63116
Propeller Replacement
! WARNING
Rotating propellers can cause serious injury or death. Never operate the boat
out of the water with a propeller installed. Before installing or removing a
propeller, place the drive unit in neutral and engage the lanyard stop switch
to prevent the engine from starting. Place a block of wood between the
propeller blade and the anti‑ventilation plate.
1. Remove the spark plug leads to prevent the engine from starting.
26899
eng 101
MAINTENANCE
2. Shift the outboard into neutral (N).
N
F R
63077
63103
3. Straighten the cotter pin and pull it out using a pair of pliers.
4. Place a block of wood between the gearcase and the propeller to prevent
rotation and remove the propeller nut.
102 eng
MAINTENANCE
5. Pull the propeller straight off of the shaft. If the propeller is seized to the
shaft and cannot be removed, have the propeller removed by an
authorized dealer.
b
d
c
31926
a- Cotter pin
b- Nut
c- Rear thrust washer
d- Front thrust hub
IMPORTANT: To prevent the propeller hub from corroding and seizing to the
propeller shaft (especially in saltwater), always apply the recommended
lubricant to the entire propeller shaft at the recommended maintenance
intervals and also each time the propeller is removed.
6. Apply Extreme Grease or 2‑4‑C with PTFE to the propeller shaft.
31927
Tube Ref
Description Where Used Part No.
No.
7. Install the front thrust hub onto the shaft so that the larger diameter end is
facing the propeller.
eng 103
MAINTENANCE
8. Install the propeller, rear thrust washer, and propeller nut onto the shaft.
9. Place a block of wood between the gearcase and the propeller to prevent
rotation and tighten the propeller nut to the specified torque.
NOTE: If the propeller nut doesn't align with the propeller shaft hole after
tightening, tighten the nut further to align with the hole.
10. Align the propeller nut with the propeller shaft hole. Insert a new cotter pin
in the hole and bend the ends.
b
d
c
31926
a- Cotter pin
b- Propeller nut
c- Rear thrust washer
d- Front thrust hub ‑ Larger diameter end toward propeller
104 eng
MAINTENANCE
The voltage regulator circuit and the electric starting circuit are protected from
overload by 20‑amp and 15‑amp ATC fuses, respectively. If a fuse opens, try to
locate and correct the cause of the overload. If the cause is not found, the fuse
may open again.
a
20 b
20
c
15 d
15
62955
To access the 15‑amp fuse, remove the fuse block from the pocket on the ECM
rubber mount. Then remove the cap from the fuse block.
Remove the fuse and examine the silver colored band inside the fuse. If band
is broken, replace the fuse. Replace the fuse with a new fuse of the same
rating.
28619
eng 105
MAINTENANCE
Spark Plug Inspection and Replacement
! WARNING
Damaged spark plug boots may emit sparks that can ignite fuel vapors under
the engine cowl, resulting in serious injury or death from a fire or explosion.
To avoid damaging the spark plug boots, do not use any sharp object or
metal tool to remove the spark plug boots.
1. Remove the spark plug boots. Twist the rubber boots slightly and pull off.
26899
2. Remove the spark plugs to inspect. Replace the spark plug if electrode is
worn or the insulator is rough, cracked, broken, blistered, or fouled.
26946
26947
Spark Plug
Spark plug gap 0.9 mm (0.035 in.)
4. Before installing the spark plugs, clean off any dirt on the spark plug
seats. Install plugs finger‑tight and then tighten 1/4 turn, or tighten to the
specified torque.
106 eng
MAINTENANCE
Timing Belt Inspection
Inspect the timing belt. Replace the belt if any of the following conditions are
found:
• Cracks in the back of the belt or in the base of the belt teeth
• Excessive wear at the roots of the cogs
• Rubber portion swollen by oil
• Belt surfaces roughened
• Signs of wear on edges or outer surfaces of belt
62878
Engine Oil
OIL CHANGE KITS
Mercury Marine offers convenient oil change kits for several outboard models
ranging from 15 hp to 150 hp. These kits contain a new filter, oil, and any
additional parts required for a complete oil change. The kits are available in
both Mercury Marine and Quicksilver brands. Refer to the following chart for
details.
eng 107
MAINTENANCE
Models Mercury P/N Quicksilver P/N
150 hp 8M0107512 8M0107513
69221
62880
Oil filter
108 eng
MAINTENANCE
2. Remove the top cowl and remove the oil filter drain hose from it's storage
location on the front of the engine.
64178
3. Tilt the engine up and lock the outboard in the full tilt position. Allow a few
minutes for the oil in the filter to drain into the engine.
4. Route the oil filter drain hose into an approved container.
b
a
64179
eng 109
MAINTENANCE
5. Remove the oil filter by turning the filter counterclockwise. If necessary,
carefully move wires temporarily out of the way, to gain clearance for the
oil filter wrench.
6. Wipe up any spilled oil.
7. Clean the mounting base. Apply a film of clean oil to the filter gasket. Do
not use grease. Install the new filter. When the gasket contacts the base,
tighten the filter an additional 3/4 to 1 turn.
8. If any components were moved or removed to gain access to the oil filter,
restore them to their original positions or install them accordingly.
63034 4537
110 eng
MAINTENANCE
FILLING THE CRANKCASE WITH OIL
IMPORTANT: Do not try to fill the oil level to the top of the operating range
(upper hole). The oil level is correct as long as it appears in the operating range
between the upper and lower hole.
1. Position the outboard in a level operating position.
2. Remove the oil fill cap and add the recommended oil to the midpoint of
the oil level operating range. Adding approximately 1.0 liter
(1.1 U.S. quart) of oil to an empty crankcase will bring the oil level to the
midpoint of the oil level range. Reinstall the oil fill cap.
62881
3. With cooling water properly supplied, idle the engine for five minutes and
check for leaks. Stop the engine and check the oil level on the dipstick.
Add oil if necessary.
eng 111
MAINTENANCE
• One anode is mounted on the starboard side of the midsection, just above
the anti‑ventilation plate. A screw and nut secure the anode to the
midsection.
62958
112 eng
MAINTENANCE
• One anode is located on the bottom of the lower engine mount. A screw
secures it and two continuity wires to the mount.
d
c
e
b
a
62942
a- Anode
b- Screw
c- Continuity wire (from swivel bracket to lower mount)
d- Lubrication fitting
e- Continuity wire (from lower mount to driveshaft housing)
eng 113
MAINTENANCE
• Two anodes are located near the bottom of the transom brackets. On
power tilt models, the anodes are on the inside area of the brackets. On
manual tilt models, the anodes are secured to the rear of the brackets.
The anodes on both models are secured to the brackets with screws.
62960
62959
114 eng
MAINTENANCE
Lubrication Points
1. Lubricate the following with 2‑4‑C with PTFE or Extreme Grease.
Tube Ref
Description Where Used Part No.
No.
Swivel bracket, transom clamp screws,
Extreme Grease tilt tube, propeller shaft, steering cable 8M0071842
grease
Swivel bracket, transom clamp screws,
95 2-4-C with PTFE tilt tube, throttle/shift cables, steering 92-802859A 1
cable grease fitting
63095
eng 115
MAINTENANCE
• Transom clamp screws lubrication fittings.
b
b
63285
b
c 63286
! WARNING
Incorrect cable lubrication can cause hydraulic lock, leading to serious
injury or death from loss of boat control. Completely retract the end of the
steering cable before applying lubricant.
2. Lubricate the following with lightweight oil.
116 eng
MAINTENANCE
• Steering link rod pivot points ‑ Lubricate points.
63287
Tube Ref
Description Where Used Part No.
No.
31927
Gearcase Lubricant
DRAINING AND INSPECTING GEAR HOUSING LUBRICANT
! WARNING
Rotating propellers can cause serious injury or death. Never operate the boat
out of the water with a propeller installed. Before installing or removing a
propeller, place the drive unit in neutral and engage the lanyard stop switch
to prevent the engine from starting. Place a block of wood between the
propeller blade and the anti‑ventilation plate.
eng 117
MAINTENANCE
1. Position a clean drain pan under the gear housing and remove the fill and
vent screws with gaskets from the gear housing.
a - Vent screw
b - Fill screw
a
64165
2. Inspect the gear lubricant for metal particles. Presence of a small amount
of fine metal particles resembling powder indicates normal wear.
Presence of larger particles or a large quantity of fine particles indicates a
need for gear housing disassembly and component inspection.
3. Note the color of the gear lubricant. White or cream color indicates the
presence of water in the lubricant. Check the drain pan for water
separation from the lubricant. Presence of water in the gear lubricant
indicates the need for disassembly and inspection of oil seals, seal
surfaces, O‑rings, and gear housing components. Pressure check the
gearcase prior to disassembly.
NOTE: When draining the gearcase for the first time, lubricant may appear
cream colored due to the mixing of assembly lubricant and gear lubricant. This
is not an indication of water intrusion. If, during subsequent draining of the
gearcase, lubricant appears cream colored or milky, water may be present.
The gearcase should be disassembled and all gaskets, seals, and O‑rings
replaced. Inspect all components for water damage.
NOTE: Gear lubricant drained from a recently run gearcase will be a light
chocolate brown in color due to agitation/aeration. Oil that is stabilized will be
a clear yellow brown in color.
GEARCASE LUBRICANT CAPACITY
Approximately 460 ml (15.6 fl oz).
118 eng
MAINTENANCE
FILLING THE GEARCASE
1. Place the outboard in a vertical operating position or in the full tilt position.
2. Remove the vent plug from the vent hole.
3. Place the lubricant tube into the fill hole and add lubricant until it appears
at the vent hole.
62882
31919
eng 119
MAINTENANCE
2. Remove the fill cap and check the fluid level. The fluid level should be
even with the bottom of the fill hole. Add Mercury or Quicksilver Power
Trim and Steering Fluid. If not available, use automotive automatic
transmission fluid (ATF).
a - Fill cap
31920
Submerged Outboard
A submerged outboard will require service within a few hours by an authorized
dealer once the outboard is recovered from the water. This immediate attention
by a servicing dealer is necessary once the engine is exposed to the
atmosphere to minimize internal corrosion damage to the engine.
120 eng
STORAGE
Storage Preparation
The major consideration in preparing your outboard for storage is to protect it
from rust, corrosion, and damage caused by freezing of trapped water.
The following storage procedures should be followed to prepare your outboard
for out‑of‑season storage or prolonged storage (two months or longer).
NOTICE
Without sufficient cooling water, the engine, the water pump, and other
components will overheat and suffer damage. Provide a sufficient supply of
water to the water inlets during operation.
FUEL SYSTEM
IMPORTANT: Gasoline containing alcohol (ethanol or methanol) can cause a
formation of acid during storage and can damage the fuel system. If the
gasoline being used contains alcohol, it is advisable to drain as much of the
remaining gasoline as possible from the fuel tank, remote fuel line, and engine
fuel system.
Fill the fuel tank and engine fuel system with treated (stabilized) fuel to help
prevent formation of varnish and gum. Proceed with the following instructions.
• Portable fuel tank—Pour the required amount of gasoline stabilizer (follow
the instructions on container) into the fuel tank. Tip the fuel tank back and
forth to mix the stabilizer with the fuel.
• Permanently installed fuel tank—Pour the required amount of gasoline
stabilizer (follow the instructions on container) into a separate container
and mix with approximately 1 Liter (1 US qt) of gasoline. Pour this mixture
into the fuel tank.
• Remove the fuel filter sight bowl and empty its contents into a suitable
container. Refer to Section 6 ‑ Fuel System for removal and installation
of the filter. Add 3 cc (1/2 tsp) of Quickstor Fuel Stabilizer into the fuel
filter sight bowl and install.
Tube Ref
Description Where Used Part No.
No.
Quickstor Fuel
124 Fuel filter sight bowl 92-8M0047932
Stabilizer
eng 121
STORAGE
• Spray Quicksilver or Mercury Precision Lubricants Corrosion Guard on
external metal surfaces (except corrosion control anodes).
Tube Ref
Description Where Used Part No.
No.
Gearcase
• Drain and refill the gearcase lubricant (refer to Gearcase Lubricant).
• Store the outboard in an upright position, horizontal with the front of the
engine facing up (tiller handle facing up), or on the port side.
63254
Upright position
122 eng
STORAGE
• The port side lower cowl has two bumpers to help reduce damage to the
cowl when the engine is stored in the laying down position. Storing the
engine on the port side will prevent oil from draining out of the crankcase
into the cylinders or crankcase ventilation system. There are bumpers on
the aft side of the top cowl also.
63255
Battery Storage
• Follow the battery manufacturer's instructions for storage and charging.
• Remove the battery from the boat and check water level. Charge if
necessary.
• Store the battery in a cool, dry place.
• Periodically check the water level and charge the battery during storage.
eng 123
TROUBLESHOOTING
Starter Motor Will Not Crank the Engine (Electric Start Models)
POSSIBLE CAUSES
• Blown 15‑amp fuse in the starting circuit. Refer to Maintenance section.
NOTE: Reverse battery connection will blow the 15‑amp fuse.
• Outboard is not shifted to neutral position.
• Weak battery or battery connections are loose or corroded.
• Ignition key switch/start button failure.
• Wiring or electrical connection faulty.
• Starter motor or starter solenoid failure.
124 eng
TROUBLESHOOTING
• Fuel pump failure.
• Ignition system component failure.
Performance Loss
POSSIBLE CAUSES
• Low oil pressure. Check the oil level.
• Warning system activated.
• Throttle not fully open.
• Damaged or improper size propeller.
• Incorrect throttle linkage setup.
• Boat overloaded or load improperly distributed.
• Excessive water in bilge.
• Boat bottom is dirty or damaged.
eng 125
OWNER SERVICE ASSISTANCE
Service Assistance
LOCAL REPAIR SERVICE
If you need service for your Mercury‑outboard‑powered boat, take it to your
authorized dealer. Only authorized dealers specialize in Mercury products and
have factory‑trained mechanics, special tools and equipment, and genuine
Quicksilver parts and accessories to properly service your engine.
NOTE: Quicksilver parts and accessories are engineered and built by Mercury
Marine specifically for your power package.
SERVICE AWAY FROM HOME
If you are away from your local dealer and the need arises for service, contact
the nearest authorized dealer. If, for any reason, you cannot obtain service,
contact the nearest Regional Service Center. Outside the United States and
Canada, contact the nearest Marine Power International Service Center.
STOLEN POWER PACKAGE
If your power package is stolen, immediately advise the local authorities and
Mercury Marine of the model and serial numbers and to whom the recovery is
to be reported. This information is maintained in a database at Mercury Marine
to aid authorities and dealers in the recovery of stolen power packages.
ATTENTION REQUIRED AFTER SUBMERSION
1. Before recovery, contact an authorized Mercury dealer.
2. After recovery, immediate service by an authorized Mercury dealer is
required to reduce the possibility of serious engine damage.
REPLACEMENT SERVICE PARTS
! WARNING
Avoid fire or explosion hazard. Electrical, ignition, and fuel system
components on Mercury Marine products comply with federal and
international standards to minimize risk of fire or explosion. Do not use
replacement electrical or fuel system components that do not comply with
these standards. When servicing the electrical and fuel systems, properly
install and tighten all components.
Marine engines are expected to operate at or near full throttle for most of their
lives. They are also expected to operate in both fresh and saltwater
environments. These conditions require numerous special parts.
PARTS AND ACCESSORIES INQUIRIES
Direct any inquiries concerning genuine Mercury Precision Parts® or
Quicksilver Marine Parts and Accessories® to a local authorized dealer.
Dealers have the proper systems to order parts and accessories, if they are not
in stock. Engine model and serial number are required to order correct parts.
126 eng
OWNER SERVICE ASSISTANCE
RESOLVING A PROBLEM
Satisfaction with your Mercury product is important to your dealer and to us. If
you ever have a problem, question or concern about your power package,
contact your dealer or any authorized Mercury dealership. If you need
additional assistance:
1. Talk with the dealership's sales manager or service manager.
2. If your question, concern, or problem cannot be resolved by your
dealership, please contact the Mercury Marine Service Office for
assistance. Mercury Marine will work with you and your dealership to
resolve all problems.
The following information will be needed by the Customer Service:
• Your name and address
• Your daytime telephone number
• The model and serial numbers of your power package
• The name and address of your dealership
• The nature of the problem
CONTACT INFORMATION FOR MERCURY MARINE CUSTOMER
SERVICE
For assistance, call, fax, or write to the geographic office in your area. Please
include your daytime telephone number with mail and fax correspondence.
Australia, Pacific
Telephone +61 3 9791 5822 Brunswick Asia Pacific Group
41–71 Bessemer Drive
Fax +61 3 9706 7228 Dandenong South, Victoria 3175
Australia
eng 127
OWNER SERVICE ASSISTANCE
Mexico, Central America, South America, Caribbean
Telephone +1 954 744 3500 Mercury Marine
11650 Interchange Circle North
Fax +1 954 744 3535 Miramar, FL 33025
U.S.A.
Ordering Literature
Before ordering literature, have the following information about your power
package available:
Mercury Marine
Telephone Fax Mail
Mercury Marine
(920) 929‑5110 (920) 929‑4894 Attn: Publications Department
(USA only) (USA only) P.O. Box 1939
Fond du Lac, WI 54936-1939
Mercury Marine
Submit the following Attn: Publications Department
order form with payment W6250 Pioneer Road
to: P.O. Box 1939
Fond du Lac, WI 54936-1939
Ship To: (Copy this form and print or type–This is your shipping label)
Name
Address
City, State, Province
ZIP or postal code
Country
128 eng
OWNER SERVICE ASSISTANCE
Quantity Item Stock Number Price Total
. .
. .
. .
. .
. .
Total Due .
eng 129
MAINTENANCE LOG
Maintenance Log
Record all maintenance performed on your outboard here. Be sure to save all
work orders and receipts.
130 eng