Experiment-1

Aim: Study of different types of Network cables and Practically implement the cross-wired
cable and straight through cable using clamping tool.

Apparatus (Components): RJ-45 connector, Climping Tool, Twisted pair Cable

Procedure: To do these practical following steps should be done:

1. Start by stripping off about 2 inches of the plastic jacket off the end of the cable. Be very
careful at this point, as to not nick or cut into the wires, which are inside. Doing so could alter
the characteristics of your cable, or even worse render is useless. Check the wires, one more time
for nicks or cuts. If there are any, just whack the whole end off, and start over.

2. Spread the wires apart, but be sure to hold onto the base of the jacket with your other hand.
You do not want the wires to become untwisted down inside the jacket. Category 5 cable must
only have 1/2 of an inch of 'untwisted' wire at the end; otherwise it will be 'out of spec'. At this
point, you obviously have ALOT more than 1/2 of an inch of un-twisted wire.

3. You have 2 end jacks, which must be installed on your cable. If you are using a pre-made
cable, with one of the ends whacked off, you only have one end to install - the crossed over end.
Below are two diagrams, which show how you need to arrange the cables for each type of cable
end. Decide at this point which end you are making and examine the associated picture below.

Diagram shows you how to prepare Cross wired connection

Diagram shows you how to prepare straight through wired connection
 Experiment - 2
Aim: Study of following Network Devices in Detail
• Repeater
• Hub
• Switch
• Bridge
• Router
• Gate Way

Apparatus (Software): No software or hardware needed.

Procedure: Following should be done to understand this practical.

1. Repeater:Functioning at Physical Layer.Arepeater is an electronic device that receives a

signal and retransmits it at a higher level and/or higher power, or onto the other side of an
obstruction, so that the signal can cover longer distances. Repeater have two ports ,so cannot be
use to connect for more than two devices

2. Hub: An Ethernet hub, active hub, network hub, repeater hub, hub or concentrator
is a device for connecting multiple twisted pair or fiber optic Ethernet devices together and
making them act as a single network segment. Hubs work at the physical layer (layer 1) of the
OSI model. The device is a form of multiport repeater. Repeater hubs also participate in collision
detection, forwarding a jam signal to all ports if it detects a collision.

3. Switch:Anetwork switch or switching hub is a computer networking device that connects

network segments.The term commonly refers to a network bridge that processes and routes data
at the data link layer (layer 2) of the OSI model. Switches that additionally process data at the
network layer (layer 3 and above) are often referred to as Layer 3 switches or multilayer
switches.

4. Bridge: A network bridge connects multiple network segments at the data link layer (Layer
2) of the OSI model. In Ethernet networks, the term bridge formally means a device that behaves
according to the IEEE 802.1D standard. A bridge and switch are very much alike; a switch being
a bridge with numerous ports. Switch or Layer 2 switch is often used interchangeably with
bridge .Bridges can analyze incoming data packets to determine if the bridge is able to send the
given packet to another segment of the network.

5. Router: A router is an electronic device that interconnects two or more computer networks,
and selectively interchanges packets of data between them. Each data packet contains address
information that a router can use to determine if the source and destination are on the same
network, or if the data packet must be transferred from one network to another. Where multiple
routers are used in a large collection of interconnected networks, the routers exchange
information about target system addresses, so that each router can build up a table showing the
preferred paths between any two systems on the interconnected networks.

6. Gate Way: In a communications network, a network node equipped for interfacing with
another network that uses different protocols.
• A gateway may contain devices such as protocol translators, impedance matching
devices, rate converters, fault isolators, or signal translators as necessary to provide
system interoperability. It also requires the establishment of mutually acceptable
administrative procedures between both networks.
• A protocol translation/mapping gateway interconnects networks with different network
protocol technologies by performing the required protocol conversions.
 Experiment - 3
Aim: Study of network IP

• Classification of IP address
• Sub netting
• Super netting

Apparatus (Software): NA

Procedure: Following is required to be study under this practical.

• Classification of IP address

As show in figure we teach how the ip addresses are classified and when they are used.

Class Address Range Supports

Class A 1.0.0.1 to 126.255.255.254 Supports 16 million hosts on each of 127 networks.
Class B 128.1.0.1 to 191.255.255.254 Supports 65,000 hosts on each of 16,000 networks.
Class C 192.0.1.1 to 223.255.254.254 Supports 254 hosts on each of 2 million networks.
Class D 224.0.0.0 to 239.255.255.255 Reserved for multicast groups.
Class E 240.0.0.0 to 254.255.255.254 Reserved.

• Sub netting
Why we Develop sub netting and How to calculate subnet mask and how to identify subnet address.

• Super netting
Why we develop super netting and How to calculate supernet mask and how to identify supernet
address.
 Experiment-4
Aim: Connect the computers in Local Area Network.

Procedure: On the host computer

On the host computer, follow these steps to share the Internet connection:
1. Log on to the host computer as Administrator or as Owner.
2. Click Start, and then click Control Panel.
3. Click Network and Internet Connections.
4. Click Network Connections.
5. Right-click the connection that you use to connect to the Internet. For example, if you
connect to the Internet by using a modem, right-click the connection that you want under Dial-up
/ other network available.
6. Click Properties.
7. Click the Advanced tab.

8. Under Internet Connection Sharing, select the Allow other network users to connect
through this computer's Internet connection check box.

9. If you are sharing a dial-up Internet connection, select the Establish a dial-up connection
whenever a computer on my network attempts to access the Internet check box if you
want to permit your computer to automatically connect to the Internet.

10. Click OK. You receive the following message:

When Internet Connection Sharing is enabled, your LAN adapter will be set to use IP address
192.168.0. 1. Your computer may lose connectivity with other computers on your network. If
these other computers have static IP addresses, it is a good idea to set them to obtain their IP
addresses automatically. Are you sure you want to enable Internet Connection Sharing?

11. Click Yes.

The connection to the Internet is shared to other computers on the local area network (LAN).

The network adapter that is connected to the LAN is configured with a static IP address of
192.168.0. 1 and a subnet mask of 255.255.255.0

On the client computer

To connect to the Internet by using the shared connection, you must confirm the LAN adapter IP
configuration, and then configure the client computer. To confirm the LAN adapter IP
configuration, follow these steps:

1. Log on to the client computer as Administrator or as Owner.

2. Click Start, and then click Control Panel.
3. Click Network and Internet Connections.
4. Click Network Connections.
5. Right-click Local Area Connection and then click Properties.
6. Click the General tab, click Internet Protocol (TCP/IP) in the connection uses the following
items list, and then click Properties.

7. In the Internet Protocol (TCP/IP) Properties dialog box, click Obtain an IP address
automatically (if it is not already selected), and then click OK.

Note: You can also assign a unique static IP address in the range of 192.168.0.2 to
254. For example, you can assign the following static IP address, subnet mask, and default gateway:

8. IP Address 192.168.31.202
9. Subnet mask 255.255.255.0
10. Default gateway 192.168.31.1

11. In the Local Area Connection Properties dialog box, click OK.

12. Quit Control Panel.

 Experiment-5
Aim: Study of basic network command and Network configuration commands.

Apparatus (Software): Command Prompt And Packet Tracer.

Procedure: To do this EXPERIMENT- follows these steps:

In this EXPERIMENT- students have to understand basic networking commands e.g ping,
tracert etc.

All commands related to Network configuration which includes how to switch to privilege mode
and normal mode and how to configure router interface and how to save this configuration to
flash memory or permanent memory.

This commands includes

• Configuring the Router commands

• General Commands to configure network
• Privileged Mode commands of a router
• Router Processes & Statistics
• IP Commands
• Other IP Commands e.g. show ip route etc.

ping:
ping(8) sends an ICMP ECHO_REQUEST packet to the specified host. If the host responds, you
get an ICMP packet back. Sound strange? Well, you can “ping” an IP address to see if a machine
is alive. If there is no response, you know something is wrong.
Traceroute:

Tracert is a command which can show you the path a packet of information takes from your
computer to one you specify. It will list all the routers it passes through until it reaches its
destination, or fails to and is discarded. In addition to this, it will tell you how long each 'hop'
from router to router takes.
nslookup:

Displays information from Domain Name System (DNS) name servers.

NOTE :If you write the command as above it shows as default your pc's server name firstly.

pathping:

A better version of tracert that gives you statics about packet lost and latency.

Getting Help

In any command mode, you can get a list of available commands by entering a question mark (?).

Router>?
To obtain a list of commands that begin with a particular character sequence, type in those
haracters followed immediately by the question mark (?).

Router#co?
configure connect copy
To list keywords or arguments, enter a question mark in place of a keyword or argument.
Include a space before the question mark.

Router#configure ?

memory Configure from NV memory network Configure from a TFTP network host terminal
Configure from the terminal
You can also abbreviate commands and keywords by entering just enough characters to make
the command unique from other commands. For example, you can abbreviate the show
command to sh.

Configuration Files

Any time you make changes to the router configuration, you must save the changes to memory
because if you do not they will be lost if there is a system reload or power outage. There are two
types of configuration files: the running (current operating) configuration and the startup
configuration.
Use the following privileged mode commands to work with configuration files.
 Experiment-6

Performing an Initial Switch Configuration

Topology Diagram

Objectives
 Perform an initial configuration of a Cisco Catalyst 2960 switch.

Background / Preparation
In this activity, you will configure these settings on the customer Cisco Catalyst 2960 switch:
 Host name
 Console password
 vty password
 Privileged EXEC mode password
 Privileged EXEC mode secret
 IP address on VLAN1 interface
 Default gateway
Note: Not all commands are graded by Packet Tracer.

Step 1: Configure the switch host name.

a. From the Customer PC, use a console cable and terminal emulation software to connect to the console
of the customer Cisco Catalyst 2960 switch.
b. Set the host name on the switch to CustomerSwitch using these commands.

Switch>enable
Switch#configure terminal
 Switch(config)#hostname CustomerSwitch

Step 2: Configure the privileged mode password and secret.

a. From global configuration mode, configure the password as cisco.

CustomerSwitch(config)#enable password cisco

b. From global configuration mode, configure the secret as cisco123.

CustomerSwitch(config)#enable secret cisco123

Step 3: Configure the console password.

a. From global configuration mode, switch to configuration mode to configure the console line.
CustomerSwitch(config)#line console 0

b. From line configuration mode, set the password to cisco and require the password to be entered at
login.

CustomerSwitch(config-line)#password cisco
CustomerSwitch(config-line)#login
CustomerSwitch(config-line)#exit

Step 4: Configure the vty password.

a. From global configuration mode, switch to the configuration mode for the vty lines 0 through 15.

CustomerSwitch(config)#line vty 0 15

b. From line configuration mode, set the password to cisco and require the password to be entered at
login.

CustomerSwitch(config-line)#password cisco
CustomerSwitch(config-line)#login
CustomerSwitch(config-line)#exit

Step 5: Configure an IP address on interface VLAN1.

From global configuration mode, switch to interface configuration mode for VLAN1, and assign the IP address
192.168.1.5 with the subnet mask of 255.255.255.0.

CustomerSwitch(config)#interface vlan 1
CustomerSwitch(config-if)#ip address 192.168.1.5 255.255.255.0
CustomerSwitch(config-if)#no shutdown
CustomerSwitch(config-if)#exit

Step 6: Configure the default gateway.

a. From global configuration mode, assign the default gateway to 192.168.1.1.

CustomerSwitch(config)#ip default-gateway 192.168.1.1

 b. Click the Check Results button at the bottom of this instruction window to check your work.

Step 7: Verify the configuration.

The Customer Switch should now be able to ping the ISP Server at 209.165.201.10. The first one or two pings
may fail while ARP converges.

CustomerSwitch(config)#end
CustomerSwitch#ping 209.165.201.10

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 209.165.201.10, timeout is 2 seconds:
..!!!
Success rate is 60 percent (3/5), round-trip min/avg/max = 181/189/197 ms

CustomerSwitch#

Reflection
a. What is the significance of assigning the IP address to the VLAN1 interface instead of any of the Fast
Ethernet interfaces?

b. What command is necessary to enforce password authentication on the console and vty lines?

c. How many gigabit ports are available on the Cisco Catalyst 2960 switch that you used in the activity?
 Experiment-7

Performing an Initial Router Configuration

Topology Diagram

Objectives
 Configure the router host name.
 Configure passwords.
 Configure banner messages.
 Verify the router configuration.

Background / Preparation
In this activity, you will use the Cisco IOS CLI to apply an initial configuration to a router, including host
name, passwords, a message-of-the-day (MOTD) banner, and other basic settings.
Note: Some of the steps are not graded by Packet Tracer.

Step 1: Configure the router host name.

a. On Customer PC, use the terminal emulation software to connect to the console of the customer Cisco
1841 ISR.
Set the host name on the router to CustomerRouter by using these commands.

Router>enable
Router#configure terminal
Router(config)#hostname CustomerRouter

Step 2: Configure the privileged mode and secret passwords.

a. In global configuration mode, set the password to cisco.
 CustomerRouter(config)#enable password cisco

Set an encrypted privileged password to cisco123 using the secret command.

CustomerRouter(config)#enable secret cisco123

Step 3: Configure the console password.

a. In global configuration mode, switch to line configuration mode to specify the console line.

CustomerRouter(config)#line console 0

Set the password to cisco123, require that the password be entered at login, and then exit line configuration mode.

CustomerRouter(config-line)#password cisco123
CustomerRouter(config-line)#login
CustomerRouter(config-line)#exit
CustomerRouter(config)#

Step 4: Configure the vty password to allow Telnet access to the router.
a. In global configuration mode, switch to line configuration mode to specify the vty
lines.

CustomerRouter(config)#line vty 0 4

Set the password to cisco123, require that the password be entered at login, exit line configuration mode, and then
exit the configuration session.

CustomerRouter(config-line)#password cisco123
CustomerRouter(config-line)#login
CustomerRouter(config-line)#exit
CustomerRouter(config)#

Step 5: Configure password encryption, a MOTD banner, and turn off domain server lookup.
a. Currently, the line passwords and the enable password are shown in clear text when you show the
running configuration. Verify this now by entering the show running-config command.

To avoid the security risk of someone looking over your shoulder and reading the passwords, encrypt
all clear text passwords.

CustomerRouter(config)#service password-encryption

Use the show running-config command again to verify that the passwords are encrypted.
To provide a warning when someone attempts to log in to the router, configure a MOTD banner.

CustomerRouter(config)#banner motd $Authorized Access Only!$

Test the banner and passwords. Log out of the router by typing the exit command twice. The banner displays before
the prompt for a password. Enter the password to log back into the router.
You may have noticed that when you enter a command incorrectly at the user or privileged EXEC prompt, the router
pauses while trying to locate an IP address for the mistyped word you entered. For example, this output shows what
happens when the enable command is mistyped.

CustomerRouter>emable
Translating "emable"...domain server (255.255.255.255)

To prevent this from happening, use the following command to stop all DNS lookups from the router
CLI.

CustomerRouter(config)#no ip domain-lookup

Save the running configuration to the startup configuration.

CustomerRouter(config)#end
CustomerRouter#copy run start

Step 6: Verify the configuration.

a. Log out of your terminal session with the Cisco 1841 customer router.
b. Log in to the Cisco 1841 Customer Router. Enter the console password when prompted.
c. Navigate to privileged EXEC mode. Enter the privileged EXEC password when prompted.
d. Click the Check Results button at the bottom of this instruction window to check your work.

Reflection
Which Cisco IOS CLI commands did you use most?

How can you make the customer router passwords more secure?