VER 06 - B - dt.

25/8/04

INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATIONS

TESTING PROCEDURE
FOR VSP D1 OF VSP D1

INTRODUCTION : CAUTION : 1. SYSTEM SUPPLY VOLTAGE :

220 / 230 / 240 / 380 / 415 VAC K 20 %
1) Ensure that your VSP D1 is -
Thank you for selecting & purchasing MINILEC
* Not installed near any heat sources like 2. AUX. SUPPLY VOLTAGE :
make phase failure relay VSP D1.The following
burner, sunlight, electric arc etc. 110 / 220 / 230 / 240 / 380 / 415 VAC K 20%
installation instructions would guide you in
* Not subjected to abnormal vibrations.
installing your VSP D1 and making best use of it. 3. FREQUENCY :
* Installed as near to the starter as possible. 50 / (60) Hz, K 3%
VSP D1 is a phase failure relay operating on Start
2 ) 3 E sensing (L1,L2,L3) is normaly taken from
negative sequence voltage sensing principle. It 4. POWER CONSUMPTION :
outgoing terminals of motor starter. But in
offers protection against 3 VA ( max.) Is it
. following conditions, sensing should be Is Check Aux. within the Wait till
* Unbalanced voltage condition. L1 NO supply voltage specified NO supply
taken from incoming side of motor starter, . 5. OUTPUT RELAY CONTACT : See Indication
at 7 & 8 of
ON ? voltage
.

tolerance
* Phase failure condition. * Fully automatic reset starter. 1 Changeover VSP D1 limits? normalizes
* Phase sequence reversal condition. * Multi speed motor starter. YES
6. OUTPUT CONTACT RATING ( RESISTIVE ) : Start motor
Your VSP D1 is an auxiliary relay and it should be * Reversible starters. YES
5Amp., 240 VAC
used along with the motor starter only. The effective * When any other auto resetting type control
working of the electromagnetic motor starter. . switch is used in series with no volt coil of the 7. LIFE EXPECTANCY : R,Y,B phase
6
Does NO
Before installing your VSP D1 Check whether the starter. starter sequence is incorrect CONSULT
.

0.5 x 10 operations at 100% rating interchange wires

hold MINILEC
motor starter is operating perfectly by starting the of 1 & 3 of VSP D1 .
motor with the “START” push button and switching 8. UNBALANCE TRIP SETTING :
40V K 6V YES
it off by “OFF” push button. If the motor does not
“START” or “STOP” on respective operations, the R,Y,B phase sequence
9. TRIP TIME DELAY : connected to VSP D1
Tighten all terminals
in power & control
starter needs to be serviced. Do not install your ELECTRICAL CONNECTIONS 3.5 Sec. K 1.5 Sec. is correct.
wiring & at 1 & 3
VSP D1 with faulty motor starter. OF VSP D1: of VSP D1
10. RESETTING :
TRIP SETTING, TRIP DELAY AND See Fig.1 for Electrical connection Auto Reset Now remove any one
details of VSP D1. fuse link in power
. RESETTING : 11. RESET GAP : circuit for all the 3
See Fig.3 for installation of VSP D1 in the 10 - 18V phases one at a time
Is
The VSP D1 is factory set to trip the starter for phase to phase
power and control wiring diagram. 12. INDICATIONS : Check phase to phase voltage
unbalance voltage between any two phases of unbalance voltage NO
L1 : Green - Power ON across 1, 2 & 3 of VSP D1 after
Auxiliary supply voltage should be as marked removing fuse link.
less than unbalanced
40V K 6V (fixed). L2 : Red - Trip Does setting of
on the front cover plate of VSP D1. VSP D1 trip VSP D1
NO
The trip time delay is between 2 to 5 secs. The Connect the auxiliary supply wires at 7 & 8. 13. ENCLOSURE : within 2-5 secs
& L2 get
VSP D1 relay resets automaticaly when the Connect R,Y,B phases at 1,2 and 3 respectively. ABS. ON ? YES
unbalance voltage is reduced to less than 20V The R,Y,B sensing should be taken from outgoing 14. DIMENSIONS (mm) : YES
between all phases. points of motor starter in case of Direct Online Overall : 76 X 30.5 X 117.5
Mounting : 68 center to center VSP D1 will not trip Load
Starter. In case of star delta starters, it should be the motor & retest as per
MOUNTING : 15. MOUNTING : Reset the relay and restart
above procedure.
taken from outgoing terminals of main contactor.
Your VSP D1 can be Rail Mounted or Panel 35 mm Rail Mounting & Panel Mounting
The output relay contacts 13 and 14 are to be
Mounted.(See fig. 4A & 4B for mounting it on RAIL connected in series with no-volt coil of the 16. WEIGHT (gms) :
VSP D1 operation is perfect.
and releasing it from RAIL respectively). It is 320 (approx.) Install it for permanent use END
contactor.
suitable for 35mm RAIL ( for panel mounting and 17. OPERATING CONDITIONS :
0 0
drilling details see fig.2 ). TEMPERETURE : -5 C to + 60 C
HUMIDITY : Upto 95% Rh
VER 06 - B - dt.25/8/04
CORRECTION Check proof
MOUNTING DIMENSIONS 1
Fig. 2 30.5 D1 TYPE BOX
Fig. 3 INSTALLATION
4.5 x 6
DRILLING DETAILS
SLOT
x x x INSTRUCTION MANUAL
MOUNTING FOR
R DIMENSIONS.
PHASE FAILURE RELAY
Y 76

VSP D1
68
B
x x x
x x x

15.25

VSP
D1
OPEN

76

35
76
27
.5
117

30 .
117.5 5
NOTE : RELAY CONTACT SHOWN FOR UNIT IN HEALTHY CONDITION

CONNECTION DIAGRAM MOUNTING ON DIN RAIL RELEASING FROM DIN RAIL

Fig. 1

1 2 3
INDICATIONS :
1 R 7 L1 : POWER ON
13
L2 : TRIP

3 B Y
TERMINAL DETAILS :
8 14 15 1-2-3 : R-Y- B PHASE VOLTAGE
2 SENSING POINTS
7 8 9
7-8 : AUXILIARY SUPPLY VOLTAGE
AS MARKED ON THE UNIT
13 14 15 9 : DUMMY CONTACTS
14-13-15 : 1 CHANGEOVER OUTPUT
RELAY CONTACTS ( NO - C - NC )

VERSION 03
NOTES : RELAY CONTACT SHOWN IN HEALTHY CONDITION. (12/04/99 )