Exprimer

EVS W/WP / EXPD P

Quick Guide

Tech. Support Div.

1
Contents Strictly Confidential

1. Introduction
- Specification
- Components
- Configuration

2. Easy Installation

2
 Strictly Confidential

1. Introduction

3
EVS W Series Specification Strictly Confidential

Model Name EVS4343W(G) EVS4343WP EVS3643W(G) EVS3643WP

a-Si TFT with IGZO TFT with a-Si TFT with IGZO TFT with
Technology
photodiode photodiode photodiode photodiode

Scintillator CsI:Tl / Gd2O2S:Tb CsI:Tl CsI:Tl / Gd2O2S:Tb CsI:Tl

Imaging area size (mm) 430 x 430 358 x 430

Pixel Matrix (Resolution) 3,072 (V) × 3,072 (H) 2,560 (V) × 3,072 (H)

Pixel Pitch(μm) 140 140

Limiting Resolution (lp/mm) > 3.6 > 3.6

77% @ 1lp/mm (TVA) 76% @ 1lp/mm (TVA)
MTF (%)
64% @ 1lp/mm (Raw) 64% @ 1lp/mm (Raw)
DQE (%) ≥ 60% @ 0.5lp/mm 60% @ 0.5lp/mm

A/D Conversion 16-bit 16-bit

Typical Dynamic Range (μGy) 70 80

Trigger Mode Lossless AED/AWC Lossless AED/AWC

Preview Image Time (sec.) ≤1 sec. (※ EWT at 0.5sec.) ≤1.0 sec. (※ EWT at 0.5 sec.)

Detector Cycle Time (sec.) ≤3.6 sec. (※ EWT at 0.5sec.) ≤3.6 sec. (※ EWT at 0.5 sec.)

Input Voltage DC +15V, 3A MAX DC +15V, 3A MAX

Power Consumption 24W (Max) 24W (Max)

Data Output/Interface Gigabit Ethernet / IEE 802.11n Gigabit Ethernet / IEE 802.11n

4
PC Requirements Strictly Confidential

Item Specification

Operating system Windows 10 64 bit SP1 (Professional Edition or higher)

CPU Intel i5-6500 or higher (or compatible CPU)

Memory 8GB or higher

Hard disk 1TB or higher

Gigabit (Detector only)

Intel® PRO 1000 Series (Gigabit LAN Card for network
interface) Min. Requirements: 1Gbps,
LAN card
Jumbo Frames: 9K
Receive Descriptors: 2K (higher than 1024)
This is not dedicated to DICOM

Monitor 23 inch, 1920 x 1080 or higher

Optional disc drive CD or DVD R/W

5
EVS A / EXPD P Series Configuration Strictly Confidential

6
EVS W/WP Series Configuration Strictly Confidential

7
 PC Configuration – IP Setting Strictly Confidential

IP address setting Network check between PC and Detector

Fixed IP

PC’s IP address
: 192.168.250.100 (Must set it up)
Detector’s IP address
: 192.168.250.135 or 136

IP address of PC must be set as the value

8
 PC Configuration – Power Save ① Strictly Confidential

LAN Card Power Save Mode PC Power Management (1)

Control Panel → Power Option → High Performance

All “Never“
Control panel → Network and Sharing center →
Network connection → Properties → Configuration → All turn-off
“allow the computer to turn off this device to save power”

9
PC Configuration – Power Save ② Strictly Confidential

PC Power Management (2)

Control Panel → Power Option → High Performance

All “Never“

10
PC Configuration – User Accounts Strictly Confidential

User Accounts

Control panel → User Accounts →

Change User Account Control Setting
“Never notify” and OK

11
PC Configuration – Firewall Setting ① Strictly Confidential

Firewall Setting (1-1)

Turn off Window Defender Firewall(Not recommended)

12
PC Configuration – Firewall Setting ② Strictly Confidential

Firewall Setting (1-2)

Add allow apps – EConsole1, E-Cali1, DRTECH_API

13
PC Configuration – Firewall Setting ③ Strictly Confidential

Firewall Setting (2)

14
PC Configuration – Firewall Setting ④ Strictly Confidential

Real-time Protection Setting(1)

1. Turn off real-time protection

2. Turn off all notification
15
 PC Configuration – Firewall Setting ⑤ Strictly Confidential

Real-time Protection Setting(2)

1. gpedit.msc > computer configuration > Administrative Templates > Windows components > Windows Defender Antivirus
2. Turn off Windows Defender Antivirus > Real-time Protection > Edit > Disable> Apply > Ok 16
 PC Configuration – Firewall Setting ⑥ Strictly Confidential

Window Defender Setting

1. gpedit.msc > computer configuration > Administrative Templates > Windows components > Windows Defender Antivirus
2. Turn off Windows Defender Antivirus > Turn off Window Defender Antivirus > Edit > Disable> Apply > Ok 17
 PC Configuration – Window Update Strictly Confidential

Window Update

1. Turn off or stop working the window update

2. Service > Window update > Right mouse > Stop 18
PC Configuration – Others(1) Strictly Confidential

Configuration for machine load balance

1. Control Panel > System > Advanced system configuration

2. Click ‘Environment Variables’ in ‘Advanced’ tab.
3. Check if there is ‘KMP_DYNAMIC_MODE’ in the ‘System variables’ list
4. If not, Click ‘New’ button to make ‘New System Variable’
* If there is the same variable already, select it and Click ‘Edit’. Change the value to ‘thread_limit’.

19
PC Configuration – GDI Object Limit Setting Strictly Confidential

Configuration for GDI object handle limit

1. Registry Editor > HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsNT\CurrentVersion\Windows

2. Double click ‘GDIProcessHandleQuotation’.
3. Select ‘Decimal’.
4. Set ‘Value data’ to 65535. 20
PC Configuration – Others(2) Strictly Confidential

Anti-Virus Setting

All are turn –off Or Exception Econsole1 S/W from Virus-scanning

21
 Strictly Confidential

2. Easy Installation
 Strictly Confidential
Easy Installation

Easy Installation SW enables fast and simple initial installation

EVS A / EXPD P-series Previous & Other Methods

LAN Cable

1) Connect Detector, Control Box and PC

2) Insert CD into PC
1) Detector connection with PC using Ethernet 3) Run the S/W installer
2) Run Easy installation S/W installer (Finish) 4) Copy map files to proper destination
5) Run SW to set the path to map

MAP files are conveniently stored within the detector for easier initial installation process

23
 Strictly Confidential
Easy Installation
Easy Installation does followings:

• Detector registration on workstation (PC)

• Downloading map files in detector (Map Inside)
• Gain calibration

Easy Installation supports following detectors:

• EVS 4343A
• EVS 4343AG
• EXPD 4343P
• EVS 4343W
• EVS 4343WG
• EVS 4343WP
• EVS 3643A
• EVS 3643AG
• EXPD 3643P
• EVS 3643W
• EVS 3643WG
• EVS 3643WP

How To Run:

• Run

• Warning! For Windows 10, you should run this program as Administrative Authority.

24
Easy Installation_(1) User Interface Strictly Confidential

① Selection: the first(stand) / second(table) / third(etc)

detector to setup.
① ⑨
② Detector’s model type, serial number, and IP address.

② This will be updated automatically after setup.

③ ③ Selection: the default exposure type.

④ ④ Selection: Folder path to download map files.

⑤ ⑤ Selection: Filename without folder path of

⑥ ⑦ downloaded map files.

If this value is ‘UNKNOWN’ or blank, then the

program set to it as serial number of connected

⑧ detector automatically.

⑥ DRTECH.ini: Open DRTECH.ini file

Upload.html: Open upload.html web page of detector.

⑦ Start to setup the detector.

⑧ Status display window.

⑨ Exit.
25
Easy Installation_(2) How To Use (1/6) Strictly Confidential

a. Check ‘1st (index 0)’ is selected.

ⓐ
b. Check and change (if needed) Exposure Type

c. Set Map folder path correctly. This can be

ⓑ different by your Acquisition Software.

ⓒ d. Set Map filename correctly. This can be different by

ⓓ your Acquisition Software.

ⓔ If the map filename is the same with serial number

of the detector, let it as ‘UNKNOWN’ or blank.

e. Click ‘Detector Setup’ button to setup.

In most case,

you may check only ⓒ Map folder and ⓓ Map filename.

26
Easy Installation_(2) How To Use (2/6) Strictly Confidential

Setup Sequence – 1. Detector registration

f. Simple warning message

This setup overwrite the legacy configuration.
Click ‘Yes’ to continue.

g. Check detector connection

Please connect the first detector ONLY.
(To avoid IP confliction).

h. Confirm connected detector

Please confirm the detector model type and the serial
number.
Click ‘Yes’ to continue.

27
Easy Installation_(2) How To Use (3/6) Strictly Confidential

Setup Sequence – 2. Map downloading

i. Automatically changed IP address

-. For dual or triple panel connection, the IP address is
changed automatically after you register the each detector.

1st 192.168.250.135 → 192.168.250.136

2nd 192.168.250.135 → 192.168.250.137
3rd 192.168.250.135 → 192.168.250.138

j. Map downloading
This step will be done automatically.
Please wait.

28
Easy Installation_(2) How To Use (4/6) Strictly Confidential

Setup Sequence – 3.Gain Calibration

Gain Calibration
Shoot X-ray to the detector if Detector is READY.
Then, Easy Installation checks x-ray does by mean
value of image.

X-ray is weak.
Mean: 99 (Recommended 25000 ~ 30000 )
X-ray is weak. Please increase x-ray and try again. Please increase x-ray and try again.

X-ray is strong.
Mean: 50000 (Recommended 25000 ~ 30000 ) Please decrease x-ray and try again.
X-ray is strong. Please decrease x-ray and try again.

X-ray is fine.
Mean: 27000 (Recommended 25000 ~ 30000 ) Please take more images with the same x-ray dose.
X-ray is Good! [1/7].

29
Easy Installation_(2) How To Use (5/6) Strictly Confidential

Setup Sequence – 3.Gain Calibration

When you get seven fine images, the gain calibration will be finished.

30
Easy Installation_(2) How To Use (6/6) Strictly Confidential

Please do workflow for ‘When using single detector’ with the first detector.
Then, select ‘2nd (index 1)’ at ⓐ in below picture, then set others like the first detector.

If you use three detectors, select ‘3rd (index 2)’ and set others for the third detector,
after the second.

31
How To Use – When using two or three detectors Strictly Confidential

Please use AP or Hub to communicate to the same LAN port at the same time.

Panel B Panel C

192.168.250.137 192.168.250.138

Wireless

PC (Workstation)
192.168.250.100

AP

192.168.250.98

32
 Strictly Confidential

3. EConsole1 Installation
Installation – Econsole1 ① Strictly Confidential

Install the Econsole1 : Run the Provided setup file.

(Users must run the file as ‘Administrator’. Right-click the file, select ‘Run as administrator’.)

34
Installation – Econsole1 ② Strictly Confidential

Install the Econsole1 : Select language and detector numbers.

Select language

Select how many detectors use

35
Installation – Econsole1 ③ Strictly Confidential

Install the Econsole1 : Select license type

1. Hardware License Protection (Dongle Key)

: Utilizes a license key embedded within a special USB device.
This device must be attached to the PC in order for Econsole1 to operate.

2. Software License Protection

: The license is provided as a serial number to be entered during installation.

36
Installation – Econsole1 ④ Strictly Confidential

Install the Econsole1 : Select model and input the serial number

1. X-ray Detector Model Selection

: Set the X-ray Detector, which will be used with Econsole1. Select the appropriate model.
2. Enter the X-ray Detector Serial Number
: Econsole1 need the calibration files and serial number.
You can confirm the serial number by file name of calibration files from Dropbox.
Copy the calibration files at C:\EConsole1\Map folder.

37
Installation – Econsole1 ⑤ Strictly Confidential

Install the Econsole1 : Select destination location

* Recommend to use the default destination location.

38
Installation – Econsole1 ⑤ Strictly Confidential

Install the Econsole1 : Input the hospital & department

39
Installation – Econsole1 ⑥ Strictly Confidential

Install the Econsole1 : Select where image files be stored

* Recommend to select to separately HDD drive.

40
Installation – Econsole1 ⑦ Strictly Confidential

Install the Econsole1 : Select start menu folder

41
Installation – Econsole1 ⑧ Strictly Confidential

Install the Econsole1 : Select additional task

42
Installation – Econsole1 ⑨ Strictly Confidential

Install the Econsole1 : Verify installation information

43
Installation – Econsole1 ⑩ Strictly Confidential

Install the Econsole1 : Additional driver installation

44
Installation – Econsole1 ⑪ Strictly Confidential

Install the Econsole1 : Complete EConsole1 installation

When Econsole1 installation is complete, 3 icons are created on the desktop.

Econsole1 : program for user
ECali1 : program for engineer
Teamviewer : remote control program 45
Installation – Econsole1 ⑫ Strictly Confidential

Setup the Econsole1 : Econsole1→ Click the configuration → Detector → Panel A

Map files should be placed at

C:\Econsole1\MAP
VD1B0101HJS.GMP
VD1B0101HJS.MAP
VD1B0101HJS.PMP

46
 Strictly Confidential

4. Ecali1 Configuration
Ecali1 Configuration ① Strictly Confidential

Installation the Ecali1

a. Right click the ‘Ecali1.exe in the installation folder (in C:\Ecali1 by default).

b. Click ‘Properties’ and select ‘Advanced’.

c. Check the ‘Run as administrator’ box, and ‘OK’.

After running ‘Ecali1’, Pop-up the error notification as blow.

It’s normal notification informing the absence of calibration files. Click ‘OK’.

48
Ecali1 Configuration ② Strictly Confidential

Setup the Ecali1: Detector Configuration

① ③
④ ① Type of Panel Model which will be added or modified.
②
⑤
EVS_2430W_GLAN

② Type of Panel added (registered)

③ Adds the Panel Model selected in ①
④ Modifies the Model of the Panel selected in ②
⑤ Deletes the most recently registered Panel.

49
Ecali1 Configuration ③ Strictly Confidential

Setup the Ecali1: Calibration files Configuration

①
②
③
④

① Configures the save path of the Pixel MAP file.

② Configures the save path of the Pixel GMP file.
③ Configures the save path of the Pixel PMP file.
④ Previous MAP file are backed up when MAP files are saved multiple times.

* The file dialogue may be opened by selecting ‘…’ on the right.

50
 Strictly Confidential

5. Wireless Option
Wireless Options ① Strictly Confidential

EVS W series have 3 types of Network Mode.

✓ Station Mode
- Default Mode.
- Detector is connected with PC through AP(Access Point).
- Detector and AP must set as same SSID.
*SSID : DRT_1 or DRT_2

✓ Detector AP Mode (5GHz)

- Using internal AP inside of Detector.
- Do not need additional AP.
- Detector is connected with PC directly.
- Wireless LAN card should support 5GHz function.
*SSID : DETECTOR_AP

(CR Mode)
✓ Detector AP Mode (CR Mode)
- Using internal AP inside of Detector.
- Do not need additional AP.
- Detector is connected with extra device like smart phone or tablet.
*SSID : DETECTOR_AP

52
Wireless Options ② Strictly Confidential

OLED screen shows the network mode status

Press for 2 seconds to change mode

Station Mode (SSID: DRT_1)

AP Blinking Mode Station Mode (SSID: DRT_2)

1 times Wired

2 times (AP_1) Station mode (DRT_1)

DETECTOR AP Mode (SSID: DETECTOR_AP)

3 times (AP_2) Station mode (DRT_2)

4 times (AP_3) Detector AP mode (DETECTOR_AP)

5 times (AP_3) CR mode (DETECTOR_AP)

CR Mode (SSID: DETECTOR_AP)
53
Wireless Configuration ① Strictly Confidential

EVS W series have 2 modes at the same time. You can set it in ECali1

1. Engineer Mode ON (Password – drt1234)

2. Configuration → Detector Tab → Detector Advanced setting

54
Wireless Configuration ② Strictly Confidential

3. Wireless → WirelessNum

55
Wireless Configuration ③ Strictly Confidential

Detector IP

SSID

WirelessNum Mode

Wired only Wired (ex. Functional cable)

AP_1 <> AP_2 Station mode (DRT_1 <-> DRT_2)

AP_1 <> Detector AP(AP_3) DETECTOR AP mode (DRT_1 <-> DETECTOR_AP)

AP_1 <> CR Mode(AP_3) CR mode (DRT_1 <-> DETECTOR_AP)

Detector AP or CR mode
Detector AP (AP_3) <> CR Mode(AP_3)
(DETECTOR_AP <-> DETECTOR_AP)

56
Wireless Configuration ④ Strictly Confidential

When you check this box, you can use AP button.

If you don’t check this box, AP button will be hold.

When you check this box, you can use AP button.

If you don’t check this box, AP button will hold.

57
 Strictly Confidential

6. AP Setting Guide
 AP Setting Guide ① Strictly Confidential

⚫ Start from default setting of NetGear. In case of changed settings from default, reset NetGear settings by pushing reset
button from back side of NetGear.

⚫ Select the “Obtain an IP address automatically” from TCP/IPv4.

59
 AP Setting Guide ② Strictly Confidential

⚫ Access the NetGear setting webpage.

⚫ Access address is http://192.168.1.1/ it takes about 10 sec to access NetGear setting webpage.
⚫ Select “No” from NetGear Wizard.

60
 AP Setting Guide ③ Strictly Confidential

⚫ Set a password “drt1234” with admin account.

⚫ Set a security question and answer(drtech) as below.
⚫ After completed admin account setting, it will be reconnected and login by ID: “admin”, Password: “drt1234”.

61
 AP Setting Guide ④ Strictly Confidential

⚫ Change Language by English then, Click “Apply” button.

62
 AP Setting Guide ⑤ Strictly Confidential

⚫ Select Region- Europe, South America, America etc. and Click “Apply” button.

63
 AP Setting Guide ⑥ Strictly Confidential

⚫ Change SSID of 5GHz Wireless AP as below.

2.4Ghz: Off

Change 5GHz SSID

1) SSID: DRT_1
2) Channel: Auto
3) Security: None

64
 AP Setting Guide ⑦ Strictly Confidential

⚫ Go to “LAN Setup” menu of Advanced setting and change IP address as below

⚫ (IP:192.168.250.98 / Subnet:255.255.255.0)
⚫ Disable “Use Router as DHCP Server”

65
 AP Setting Guide ⑧ Strictly Confidential

⚫ Change PC IP Address as below

⚫ IP:192.168.250.100 / Subnet: 255.255.255.100
⚫ Access NetGear webpage.
⚫ Check the settings(SSID, IP Address, Subnet mask, Security, Channel, 5Ghz etc)

66
 Strictly Confidential

Thank you
-End-

67