Scribd
Upload
5 views

Security Indicator Light Does not Blink

This document outlines the inspection procedure for the theft deterrent/keyless entry immobiliser system in Toyota vehicles, specifically addressing issues with the security indicator light not blinking. It includes steps for performing active tests using the GTS, checking harness and connectors, and verifying the transponder key ECU assembly. The document also provides troubleshooting results and actions based on the outcomes of the tests conducted.

Uploaded by

aliubedlophkhociik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
5 views

Security Indicator Light Does not Blink

This document outlines the inspection procedure for the theft deterrent/keyless entry immobiliser system in Toyota vehicles, specifically addressing issues with the security indicator light not blinking. It includes steps for performing active tests using the GTS, checking harness and connectors, and verifying the transponder key ECU assembly. The document also provides troubleshooting results and actions based on the outcomes of the tests conducted.

Uploaded by

aliubedlophkhociik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Inspection Procedure - Toyota Service Information 12/3/17, 12(29 am

Print Exit

THEFT DETERRENT / KEYLESS ENTRY IMMOBILISER SYSTEM(w/o Entry and Start System) Security
Indicator Light Does not Blink

DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
If the transponder key ECU assembly is replaced, refer to Service Bulletin.

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)

a. Connect the GTS to the DLC3.

b. Turn the ignition switch to ON.

c. Turn the GTS on.

d. Enter the following menus: Body Electrical / Immobiliser / Active Test.

e. Perform the Active Test according to the display on the GTS.


Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Theft warning indicator
Security Indicator ON/OFF -
light assembly

Body Electrical > Immobiliser > Active Test


Tester Display
Security Indicator

https://toyotamanuals.com.au/docs/hilux-service-repair-manu…RM100000000LWVU.html?PUB_TYPE=RM&MODE=3#RM100000000LWVU_04 Page 1 of 3
Inspection Procedure - Toyota Service Information 12/3/17, 12(29 am

Execute

OK:
Security indicator light can be turned on and off using the GTS.

Result:
Proceed to
OK
NG

OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT


WARNING INDICATOR LIGHT ASSEMBLY AND BODY GROUND)

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT WARNING
INDICATOR LIGHT ASSEMBLY AND BODY GROUND)

a. Disconnect the G16 transponder key ECU assembly connector.

b. Disconnect the H2 theft warning indicator light assembly connector.

c. Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Specified
Condition
Connection Condition
H2-2 (LP) -
Always Below 1 Ω
G16-8 (IND)
H2-6 (E) -
Always Below 1 Ω
Body ground
H2-2 (LP) - 10 kΩ or
Always
Body ground higher
G16-8 (IND) - 10 kΩ or
Always
Body ground higher

Result:
Proceed to
OK
NG

OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

https://toyotamanuals.com.au/docs/hilux-service-repair-manu…RM100000000LWVU.html?PUB_TYPE=RM&MODE=3#RM100000000LWVU_04 Page 2 of 3
Inspection Procedure - Toyota Service Information 12/3/17, 12(29 am

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

a. Connect the G16 transponder key ECU assembly connector.

b.

*a Front view of wire harness connector


(to Theft Warning Indicator Light Assembly)

Measure the voltage and check for pulses according to the value(s) in the table below.
Standard Voltage:
Tester Switch Specified
Connection Condition Condition
Ignition switch Pulse
H2-2 (LP) - off generation
Body ground Ignition switch
Below 1 V
ON

Result:
Proceed to
OK
NG

OK

REPLACE THEFT WARNING INDICATOR LIGHT ASSEMBLY

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT


ASSEMBLY>REMOVAL

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

© 2012 TOYOTA MOTOR CORPORATION. All Rights Reserved.

https://toyotamanuals.com.au/docs/hilux-service-repair-manu…RM100000000LWVU.html?PUB_TYPE=RM&MODE=3#RM100000000LWVU_04 Page 3 of 3

You might also like