www.6comgiga.

com

10GBASE-ZR XFP 1550nm 80km Transceiver

P/N:6C-XFP-ZR

Features
 XFP MSA Compliant

 data rate from 9.95 Gbps to 11.1Gbps

 No Reference Clock required

 Cold Start up Wavelength Compliance

 EML transmitter and APD receiver

 link length up to 80km

 Low Power Dissipation 3.5W Maximum

 -5ºC to 70ºC Operating Case Temperature

 Diagnostic Performance Monitoring of module temperature, supply Voltages,

 laser bias current, transmit optical power, receive optical power

 RoHS compliant and lead free

Applications
 SONET OC-192&SDH STM 64

 10G Ethernet

 80 km 10G Fiber Channel

[email protected] Rev 3.0 1/5

 www.6comgiga.com

I. Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Supply Voltage 1 Vcc3 -0.5 4.0 V
Supply Voltage 2 Vcc5 -0.5 6.0 V
Supply Voltage 3 Vcc2 2
Storage Temperature Tst -40 85 ºC
Case Operating Top -5 70 ºC
Optical Input Received APD-IN - -8 dBm

II. Operating Conditions

Parameter Symbol Min Typical Max Unit
Supply Voltage 1 Vcc3 3.13 3.3 3.47 V
Supply current 1 Icc3 750 mA
Supply Voltage 2 Vcc5 4.75 5 5.25 V
Supply current 2 Icc5 500 mA
Supply Voltage 3 Vcc2 1.71 1.8 1.89 V
Supply current 3 Icc2 750 mA
Operating Case temperature Tca -5 - 70 ºC
Module Power Dissipation Pm - 3.5 W

III. Transmitter Specifications – Optical

Parameter Symbol Min Typical Max Unit
Data Rate Multirate Mra 9.95 - 11.1 Gbps
Center Wavelength λc 1550 pm
Optical Transmit Power Po 0 - +4 dBm
Optical Transmit Power PTX_DISABLE - - -30 dBm
Extinction Ratio ER 8.2 - dB
Channel Spacing ∆f - 100 - GHz
Jitter Generation TJP-P - - 0.1 UI
Spectral Width (-20dB) Dl20 - 0.1 0.3 nm
Side Mode Suppression SMSR 30 - - dB
Dispersion DP 2 dB
Eye Mask Compliant with ITU-T G.691 STM-64 eye mask

IV. Transmitter Specifications – Electrical

Parameter Symbol Min Typical Max Unit
Input differential Rim - 100 - Ω
Differential data Input VtxDIFF 120 - 850 mV
Transmit Disable Voltage VD 2.0 - Vcc3+0.3 V
Transmit Enable Voltage Ven 0 - +0.8 V
Transmit Disable Assert Vn - - 10 us

[email protected] Rev 3.0 2/5

 www.6comgiga.com

V. Receiver Specifications – Optical

Parameter Symbol Min Typical Max Unit
Data Rate Multirate Mra 9.95 - 11.1 Gbps
Receiver Sensitivity Rsens9 - - -24 dBm
Receiver Sensitivity Rsens10 - - -23 dBm
Maximum Input Power RX-overload - - -7 dBm
Input Operating λ 1528 - 1564 nm
Reflectance Rrx - - -27 dB
Loss of Signal Asserted -37 - - dBm
LOS De-Asserted - - -27 dBm
LOS Hysteresis 0.5 - - dB

VI. Receiver Specifications – Electrical

Parameter Symbol Min Typical Max Unit
Differential Output Vout P-P 350 - 850 mV
Rise/Fall Time Tr / Tf 24 - - ps
Loss of Signal – VOH 2 - Vcc3+0.3- V
Loss of Signal – VOL 0 - +0.4 V

VII. Low Speed Electrical Signal Timings

Parameter Symbol Min Typical Max Unit
TX Disable, VIH 2.0 Vcc3+0.3 V
Power_Down/RST VIL -0.3 0.8 V
Interrupt, Mod_NR, VOH Vdd3-0.5 Vdd3+0.3 V
Rx_Los VOL 0 0.4 V
VIH Vdd3*0.7 Vdd3+0.5 V
SCL,SDA(IN)
VIL -0.3 Vdd3*0.3 V
VOH Vdd3-0.5 Vdd3+0.3 V
SCL,SDA(OUT)
VOL 0 0.4 V
I2C clock rate t_reset - 400 KHz
Leakage current IL - - 100 uA

[email protected] Rev 3.0 3/5

 www.6comgiga.com

VIII. Pin Definitions

IX. Pin Descriptions

Pin Logic Symbol Name/Description Ref.
1 GND Module Ground 1
2 VEE5 Optional –5.2 Power Supply – Not required
Module De-select; When held low allows the module
3 LVTTL-I Mod-Desel
to , respond to 2-wire serial interface commands
Interrupt (bar); Indicates presence of an important
4 LVTTL-O Interrupt condition which can be read over the serial 2-wire 2
interface
Transmitter Disable; Transmitter laser source turned
5 LVTTL-I TX_DIS
off
6 VCC5 +5 Power Supply
7 GND Module Ground 1
8 VCC3 +3.3V Power Supply
9 VCC3 +3.3V Power Supply
10 LVTTL-I SCL Serial 2-wire interface clock 2
LVTTL-
11 SDA Serial 2-wire interface data line 2
I/O
Module Absent; Indicates module is not present.
12 LVTTL-O Mod_Abs 2
Grounded in the module.
13 LVTTL-O Mod_NR Module Not Ready; 2
14 LVTTL-O RX_LOS Receiver Loss of Signal indicator 2
15 GND Module Ground 1
16 GND Module Ground 1
17 CML-O RD- Receiver inverted data output
18 CML-O RD+ Receiver non-inverted data output
19 GND Module Ground 1

[email protected] Rev 3.0 4/5

 www.6comgiga.com

20 VCC2 +1.8V Power Supply

Power Down; When high, places the module in the
21 low power stand-by mode and on the falling edge of
P_Down initiates a module reset
LVTTL-I P_Down/RST
Reset; The falling edge initiates a complete reset of
the module including the 2-wire serial interface,
equivalent to a power cycle.
22 VCC2 +1.8V Power Supply
23 GND Module Ground 1
Reference Clock non-inverted input, AC coupled on
24 PECL-I RefCLK+ 3
the host board – Not required
Reference Clock inverted input, AC coupled on the
25 PECL-I RefCLK- 3
host board – Not required
26 GND Module Ground 1
27 GND Module Ground 1
28 CML-I TD- Transmitter inverted data input
29 CML-I TD+ Transmitter non-inverted data input
30 GND Module Ground 1
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector; should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.
3. A Reference Clock input is not required.

X. Ordering information
Part Number Product Description
6C-XFP-ZR XFP 10Gbps 1550nm SMF 80km DDM LC connector -5℃ ~ +70℃

[email protected] Rev 3.0 5/5