S P E C I F I C AT I O N

Customer:
Model Name: HT043DA-V.0
SPEC NO.:
Date: 2016/10/28
Version: 02

□ Preliminary Specification
■ Final Specification

For Customer ’s Acceptance

Approved by Comment
 Record of Revision

Version Revise Date Page Content

Pre-spec.01 2016/06/24 Initial Release.

.02 2016/07/11 3 Modify the pin 32: HSYNC, pin33: VSYNC of the pin
assignment to the pin 32: NC, pin33: NC
7 Modify the timing characteristics
13 Modify the test conditions of high temperature and
humidity from 40 ℃, 90%RH to (+60) ℃, (90)%RH
16 Modify the packaging material table and the packaging
quantity
Final-spec.01 2016/08/13 1 Add the value of the backlight power consumption
1 Add the value of the panel power consumption
1 Add the value of weight
Modify the FPC connector model from
2
FH19SC-40S-0.5SH(05) to FH19SC-40S-0.5SH

8 Modify the timing characteristics

Modify the FPC connector model from
15
FH19S-40S-0.5SH(05) to FH19SC-40S-0.5SH
16 Add the value of the total weight

.02 2016/10/28 5 Modify the Note1 of the typical operation conditions

8 Modify the timing diagram

10 Modify the configuration of the FPC in the chart

Add the mechanical drawing of the electronic component

15
area in FPC
Modify the configuration of the FPC in the packaging
17
drawing
 Contents

1. General Specifications ……………………………………………………………………………...1

2. Pin Assignment ………………………………………………………………………………...2
3. Operation Specifications ………………………………………………………………………...4
3.1. Absolute Maximum Ratings ............................................................................................4
3.2. Typical operation conditions............................................................................................5
3.3 Backlight Driving Conditions...........................................................................................5
3.4. Power Sequence.............................................................................................................6
3.5. Timing Characteristics.....................................................................................................7
3.5.1. Timing Conditions ...................................................................................................7
3.5.2. Timing Diagram.......................................................................................................8
4. Optical Specifications ………………………………………………………………………………...9
5. Reliability Test Items ……………………………………………………………………………….13
6. General Precautions ……………………………………………………………………………….14
6.1. Safety.............................................................................................................................14
6.2. Handling.........................................................................................................................14
6.3. Static Electricity..............................................................................................................14
6.4. Storage ..........................................................................................................................14
6.5. Cleaning.........................................................................................................................14
7. Mechanical Drawing ……………………………………………………………………………….15
8. Package Drawing ……………………………………………………………………………….16
8.1. Packaging Material Table ...............................................................................................16
8.2. Packaging Quantity........................................................................................................16
8.3. Packaging Drawing ........................................................................................................17
No. Item Specification Remark

1 LCD size 4.3 inch(Diagonal)

2 Driver element a-Si TFT active matrix

3 Resolution 480 × 3 (RGB) × 272

4 Display mode Normally White, Transmissive

5 Dot pitch 0.066(W) × 0.198(H) mm

6 Active area 95.04(W) × 53.856(H) mm

7 Module size 105.5(W) × 67.2(H) × 2.9(D) mm Note 1

8 Surface treatment Anti-Glare

9 Color arrangement RGB-stripe

10 Interface Digital

11 Backlight Power consumption 0.792 W (Typ.)

12 Panel Power consumption 0.056 W (Typ.)

13 Weight 48g (Typ.)

Note 1: Refer to Mechanical Drawing.
2. Pin Assignment
FPC Connector is used for the module electronics interface. The recommended model
is FH19SC-40S-0.5SH manufactured by HIROSE.
Pin No. Symbol I/O Function Remark

1 VLED- P Power for LED backlight cathode

2 VLED+ P Power for LED backlight anode

3 GND P Power ground

4 VDD P Power voltage

5 R0 I Red data (LSB)

6 R1 I Red data

7 R2 I Red data

8 R3 I Red data

9 R4 I Red data

10 R5 I Red data

11 R6 I Red data

12 R7 I Red data (MSB)

13 G0 I Green data (LSB)

14 G1 I Green data

15 G2 I Green data

16 G3 I Green data

17 G4 I Green data

18 G5 I Green data

19 G6 I Green data

20 G7 I Green data (MSB)

 21 B0 I Blue data (LSB)

22 B1 I Blue data

23 B2 I Blue data

24 B3 I Blue data

25 B4 I Blue data

26 B5 I Blue data

27 B6 I Blue data

28 B7 I Blue data (MSB)

29 GND P Power ground

30 CLK I Pixel clock

31 DISP I Display on/off

32 NC - No Connection

33 NC - No Connection

34 DE I Data Enable

35 NC - No Connection

36 GND P Power ground

37 NC - No Connection

38 NC - No Connection

39 NC - No Connection

40 NC - No Connection
I: input, O: output, P: Power
3. Operation Specifications
3.1. Absolute Maximum Ratings
(Note 1)
Values
Item Symbol Unit Remark
Min. Max.

Power voltage VDD -0.5 5.0 V

Input signal voltage Logic input -0.5 5.0 V

Operation temperature TOP -20 70 ℃

Storage temperature TST -30 80 ℃

Each LED
LED Reverse Voltage VR - 1.2 V
Note 2
LED Forward Current IF - 25 mA Each LED
Note 1: The absolute maximum rating values of this product are not allowed to be
exceeded at any times. A module should be used with any of the absolute
maximum ratings exceeded, the characteristics of the module may not be
recovered, or in an extreme condition, the module may be permanently
destroyed.
Note 2: VR Conditions: Zener Diode 20mA
 3.2. Typical operation conditions

Values
Item Symbol Unit Remark
Min. Typ. Max.

Power voltage VDD 3.1 3.3 3.5 V

Current for Driver IVDD - 17 25 mA VDD = 3.3V

Input logic high voltage VIH 0.8VDD - VDD V

Note 1
Input logic low voltage VIL GND - 0.2VDD V

Note1: CLK, DE, HS, VS, R0~ R7, G0~ G7, B0~ B7.

3.3 Backlight Driving Conditions

Values
Item Symbol Unit Remark
Min. Typ. Max.

Voltage for LED Backlight VL 21.0 22 23.0 V Note 2

Current for LED Backlight IL

LED life time - 20,000 - - Hr Note 1

Note 1: The “LED life time” is defined as the module brightness decrease to 50%
original brightness that the ambient temperature is 25℃ and IL =25mA. The
LED lifetime could be decreased if operating IL is lager than 40 mA.
Note 2: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and
IL =25mA.
3.4. Power Sequence

To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
should be as the diagram below.

Symbol Specification Symbol Specification

T1 0≦T1≦10 msec T4 160 msec ≦T4

T2 0≦T2≦100 msec T5 160 msec ≦T5

T3 0≦T3≦200 msec T6 1 msec ≦T6

3.5. Timing Characteristics
3.5.1. Timing Conditions
Parallel DE mode RGB input timing table
Value
Parameter Symbol Unit
Min. Typ. Max.

CLK frequency fclk 7 9 12 MHz

DEV period time Tv 277 288 400 H

DEV display area Tvd 272 H

DEV blanking Tvb 5 16 128 H

DEH period time Th 520 525 800 CLK

DEH display area Thd 480 CLK

DEH blanking Thb 40 45 320 CLK

CLK cycle time Tclk 83 110 143 ns

Clock width of high level Tcwh 40 50 60 %

Clock width of low level Tcwl 40 50 60 %

Clock rising time trck - 9 ns

Clock falling time tfck - 9 ns

Data Setup Time tdesu 10 - - ns

Data Hold Time tdahd 10 - - ns

DE Setup Time tdesu 10 - - ns

DE Hold Time tdehd 10 - - ns

3.5.2. Timing Diagram
 4. Optical Specifications

Values
Item Symbol Condition Unit Remark
Min. Typ. Max.

θL Φ=180°(9 o’clock) 60 70 -

θR Φ=0°(3 o’clock) 60 70 -
Viewing angle Note 1
degree
(CR≥ 10)
θT Φ=90°(12 o’clock) 40 50 -

θB Φ=270°(6 o’clock) 60 70 -

TON - 10 20 msec Note 3

Response time
TOFF - 15 30 msec Note 3

Contrast ratio CR 400 500 - - Note 4

Normal
WX θ=Φ=0° 0.26 0.31 0.36 - Note 2
Color chromaticity Note 5
WY 0.28 0.33 0.38 - Note 6

Luminance L 270 280 - cd/m² Note 6

Luminance uniformity YU 70 75 - % Note 7

Test Conditions:
1. VDD=3.3V, IL=40mA (Backlight current), the ambient temperature is 25℃.
2. The test systems refer to Note 2.
Note 1: Definition of viewing angle range
Normal line
θ=Φ=0°

Φ=90°
12 o’clock direction
θR
θL
θB θT

Φ=180° Φ=0°
Active Area

Φ=270°
6 o’clock direction
Fig. 4-1 Definition of viewing angle

Note 2: Definition of optical measurement system.

The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD
screen. (Response time is measured by Photo detector TOPCON BM-7, other
items are measured by BM-5A/Field of view: 1° /Height: 500mm.)

Photo detector Normal line

θ=Φ=0°

Φ=90°
500mm 12 o’clock direction

Φ=180° Φ=0°

Active Area

Φ=270°
6 o’clock direction

Fig. 4-2 Optical measurement system setup

 Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval
between “White” state and “Black” state. Rise time (TON) is the time between
photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is
the time between photo detector output intensity changed from 10% to 90%.

White (TFT OFF) Black (TFT ON) White (TFT OFF)

Photo detector output

100%
(Relative value)

90%

10%
0%
TON TOFF
Fig. 4-3 Definition of response time

Note 4: Definition of contrast ratio

Luminance measured when LCD on the " White" state
Contrast ratio (CR) =
Luminance measured when LCD on the " Black" state
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: All input terminals LCD panel must be ground while measuring the center area
of the panel. The LED driving condition is IL=20mA .
Note 7: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every
measuring point is placed at the center of each measuring area.
B min
Luminance Uniformity (Yu) =
B max
L-------Active area length W----- Active area width

L
W/6

L/6 L/3 L/3

W/3
W

W/3

Fig. 4-4 Definition of measuring points

Bmax: The measured maximum luminance of all measurement position.

Bmin: The measured minimum luminance of all measurement position.
5. Reliability Test Items
(Note3)

Item Test Conditions Remark

High Temperature Storage Ta = 80℃ 240 hrs Note 1,Note 4

Low Temperature Storage Ta = -30℃ 240hrs Note 1,Note 4

High Temperature Operation Ts = 70℃ 240hrs Note 2,Note 4

Low Temperature Operation Ta = -20℃ 240hrs Note 1,Note 4

Operate at High Temperature
+60℃, 90%RH 240 hrs Note 4
and Humidity
-30℃/30 min ~ +80℃/30 min for a total
Thermal Shock 100 cycles, Start with cold temperature Note 4
and end with high temperature
Frequency range:10~55Hz
Stroke:1.5mm
Vibration Test Sweep:10Hz~55Hz~10Hz
2 hours for each direction of X. Y. Z.
(6 hours for total)
100G 6ms,±X, ±Y, ±Z 3 times for each
Mechanical Shock
direction
Random Vibration :
0.015G*G/Hz from 5-200HZ,
Package Vibration Test -6dB/Octave from 200-500HZ
2 hours for each direction of X. Y. Z.
(6 hours for total)
Height:60 cm
Package Drop Test
1 corner, 3 edges, 6 surfaces
± 2KV, Human Body Mode,
Electro Static Discharge
100pF/1500Ω
Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panel’s surface.
Note 3: In the standard condition, there shall be no practical problem that may affect
the display function. After the reliability test, the product only guarantees
operation, but doesn’t guarantee all the cosmetic specification.
Note 4: Before cosmetic and function tests , the product must have enough recovery
time, at least 2 hours at room temperature.
6. General Precautions
6.1. Safety

Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches
your skin or clothes, wash it off immediately by using soap and water.

6.2. Handling

1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or
to excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it
carefully to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module surface
with bare hands.
4. Keep a space so that the LCD panels do not touch other components.
5. Put cover board such as acrylic board on the surface of LCD panel to protect
panel from damages.
6. Transparent electrodes may be disconnected if you use the LCD panel under
environmental conditions where the condensation of dew occurs.
7. Do not leave module in direct sunlight to avoid malfunction of the ICs.

6.3. Static Electricity

1. Be sure to ground module before turning on power or operating module.

2. Do not apply voltage which exceeds the absolute maximum rating value.

6.4. Storage

1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or
less.
2. Do not store the module in surroundings containing organic solvent or corrosive
gas.
3. Store the module in an anti-electrostatic container or bag.

6.5. Cleaning

1. Do not wipe the polarizer with dry cloth. It might cause scratch.
2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might
permanent damage to the polarizer.
7. Mechanical Drawing

HT043DA-V.0