LASER AND ITS APPLICATIONS

Popular Science & Technology Series

Laser and its Applications
01 . Introduction
No other scientific discovery of the 20th century has been demonstrated with so many
exciting applications as the laser acronym for (Light Amplification by Stimulated
Emission of Radiation). The basic concepts of laser were first given by an American
scientist, Charles Hard Townes, and two Soviet scientists, Alexander Mikhailovich
Prokhorov and Nikolai Gennediyevich Basov who shared the coveted Nobel Prize
(1964). However, TH Maiman of the Hughes Research Laboratory, California, was the
first scientist who experimentally demonstrated laser by flashing light through a ruby
crystal, in 1960.

Laser is a powerful source of light having extraordinary properties which are not found in
the normal light sources like tungsten lamps, mercury lamps, etc. The unique property of
laser is that its light waves travel very long distances with every little divergence. In the
case of a conventional e source of light, the light is emitted in a jumble of e separate
waves that cancel each other at random (Fig. 1.1a) and hence can travel very short
distances only. An analogy can be made with a situation where a large number of pebbles
are thrown into a pool at the same time. Each pebble generates a wave of its own. Since
the pebbles are thrown at random, the waves generated by all the pebbles cancel each
other and as a result, they travel a very short distance only. On the other hand, if the
pebbles are thrown into a pool one by one at the same place and also at constant intervals
of time, the waves thus generated strengthen each other and travel long distances. In this
case, the waves are said to travel coherently. In laser, the light waves are exactly in step
with each other and thus have a fixed phase relationship (Fig. 1.1b).

It is this coherency that makes all the difference to make the laser light so narrow, so
powerful and so easy to focus on a given object. The light with such qualities is not found
in nature.

A high degree of directionality ordinary n, its beam would have fanned out to such an ext.

01
 Another remarkable feature of laser is the concentration of its energy to extremely high
intensities, the intensity remaining almost constant over long distances because of low
divergence. If a laser beam with a power of a few megawatts (106 W) is focused by a lens
at a spot with a diameter of 1/1000th of a centimeter, the beam intensity increases to a
few hundred billion watts per sq. cm. This concentrated energy is so intense that it easily
ionizes the atmospheric air to create sparks (Fig. 1.2). With the beam focused from a high
power laser, even the hardest material like "diamond can be melted in a fraction of a
second.

These unique characteristics of laser have made it an important tool in various

applications. The initial notable application of laser was made c on the lunar ranging
experiment of the Apollo II Mission of 1969 when an array of retroreflectors was
mounted on the surface of the moon and pulses from a ruby laser were sent from the
earth. The reflected beams were received by suitable detectors and by measuring the time
taken by the pulses in going from the earth to the moon and back, the distance of the
moon from the earth was calculated to an accuracy of 15 cm.

After the first demonstration of laser in 1960, new applications of lasers in the various
field are announced almost every day. Laser finds applications In the fields of
communication,

02
Industry, medicine, military operations, scientific research, etc. Besides, the laser has
already brought great benefits in surgery, photography, holography, engineering, and data
storage. Though it is not possible to illustrate all the laser applications reported so far in
this small book, the more important ones are covered in the Chapters on Laser Applications.

03
1. How Laser Works
1.1 Laser Action & Quantum Theory

Laser action is based on well-established principles of quantum theory. Albert Einstein,

the greatest modern physicist, enunciated that an excited atom or a molecule, when
stimulated by an electromagnetic wave (i.e., light), would emit photons (packets of light)
having the same wavelength as that of the impinging electromagnetic wave. Charles
Townes was the first person who took advantage of this stimulated emission process as
an amplifier by conceiving and fabricating the first maser (an acronym for Microwave
Amplification by Stimulated Emission of Radiation). The first maser was produced in
ammonia vapor at a wavelength of 1.25 cm. Extending the maser principle to optical
wavelengths, Townes along with Arthur Leonard Schawlow developed the concept of
using a laser amplifier and an optical mirror cavity to provide the multiple reflections
necessary for rapid growth of light signal into an intense visible beam.

1.1.1 Principle of Laser Action

Every atom, according to the quantum theory, can have energies only in certain discrete
states or energy levels. Normally, the atoms are in the lowest energy state or ground state.
When light from a powerful source like a flash lamp or a mercury arc falls on a
substance, the atoms in the ground state can be excited to go to one of the higher levels.
This process is called absorption. After staying in that

same excited state in the same phase, This process, emission, The laser is thus analogous
to a spring that is wound up and cocked, It needs a key to release it, In this p emitted.

04
1.1.2 Amplification & Population Inversion

When favorable conditions are created for the stimulated emission, more an more atoms
are forced to give up photons thereby initiating a chain reaction and releasing vast
amount of energy, This results in rapid build up of energy of emitting one particular
wavelength (monochromatic light), traveling coherently in a precise, fixed direction. This
process is called amplification by stimulated emission.

The number of atoms in any level at a given time is called the population of that level.
Normally, when the material is not excited externally, the population of the lower level or
ground state is greater than that of the upper level. When the population of the upper
level exceeds that of the lower level, which is a reversal of the normal occupancy, the
process is called population inversion. This situation is essential for a laser action. For
any stimulated emission, It is necessary that the upper energy level or met stable state
should have a long lifetime, i.e., the atoms should pause at the met stable state for more
time than at the lower level. Thus, for laser action, the pumping mechanism (exciting with
an external source) should be from a such, as to maintain a higher population of atoms in
the upper energy level relative to that in the lower level.

1.1.3 Designing a Laser

A laser generally requires three components for its operation: (a) an active medium in the
form of a laser rod, with energy levels that can be selectively populated; (b) a pumping
process to produce population inversion between some of these energy levels; and (c) a
resonant cavity containing the active medium which serves to store the emitted radiation
and provides feedback to maintain the coherence of the radiation (Fig. 2.2).

05
The main problem in designing a laser is to produce a sufficiently high population of
atoms in the excited state. For this, many ingenious ways fully all have been evolved. The
most common method of center excitation is by sending an intense beam of light from a
flash lamp or a continuous source of light through the material in the form of a cylindrical
rod or a container tube with a suitable gas. Only those materials which can be pumped to
achieve population inversion, are used to give laser radiation. The existence of states
whose mean life times are relatively long so as to help pile up considerable energy in the
excited levels, is necessary. Long life time of a level and the sharpness of the spectrum
lines usually go together, and so, the materials that can be best used to give laser radiation
are crystals with sharp lines, and gases at low pressure.

An important aspect of the laser operation involves the design of a resonator cavity to
maximize the process of stimulated emission. Two carefully aligned mirrors, one having
more than 99 percent reflectivity and the other having less reflectivity, are placed at either
end of the cavity containing the laser rod and the flash lamp. The stimulated radiation
multiplies by bouncing back and forth many times between the two mirrors and passing
through the laser medium. And, when it exceeds a certain limit, the laser light comes out
citation in the form of a narrow pencil beam through the semi-transparent mirror.

Different types of lasers operate in different xenon f parts of the electromagnetic

spectrum- some in the visible region, some in the infrared region, and others in the
ultraviolet region. Some lasers produce continuous light beams while others give pulses
of light (of less than millisecond duration). Basically, there are two types of lasers-the
continuous wave (CW) laser and the pulsed beam allow laser. In the CW laser, the light is
emitted as a, steady continuous beam, generally, with less intensity. Gas lasers belong to
this category. On the other hand, the pulsed lasers produce powerful bursts of light of
short duration. Crystals, glass and liquid types of lasers belong to this category. Normally
the solid state lasers operate intermittently, mainly due to the large amount of heat
developed In the crystal.

06
1.1.4 Increasing the Laser Power

The power of an ordinary pulsed laser can be Increased rare eThe greater the length of the
laser rod, the higher the energy generated. This, in turn, requires hundreds of joules in
milliseconds for excitation,- using a flash lamp-like xenon discharge tube.

In an ordinary laser system, the laser rod is kept between the reflecting mirrors, with the
xenon flash tube providing the energy for pumping; the stored energy is released in short
intervals into bursts of a laser beam. In Q-switching, lasers pro- the amount of energy
stored is much more, which is achieved by interposing a fast acting shutter in duration).
between one end of the laser rod and the partially reflecting mirror (Fig. 2.3). The shutter
does not allow the laser radiation to be released for a predetermined time. After sufficient
energy is stored in the energy level, the shutter is opened for a very short interval of about
a nanosecond (one-billionth of a second) and all the stored energy is released as one giant
pulse. This technique can be compared to a river dam where the lifting of a sluice gate
releases water in a gush.

There are several ways of blocking and unblocking the optical paths between the mirrors.
Different types of Q-switches like rotating prism, polarizing device, and dye solutions are
employed. The tremendous energy released in this way can pierce through not only thick
metallic plates but also the hardest material like diamond.

1.1.5 Inversion Mechanisms

Population inversion, which gives rise to laser action, is brought about in different media
by various mechanisms. In gases, metal vapors, and plasmas, the inversion is brought out
by applying a voltage drop across the elongated gain of amplifier lengths of the order of
25 to 100 cm. Typical pressures for gas lasers range from and above.

In liquids, most of the excited states decay so rapidly due to collisions n an upper laser
level and to achieve significant gain. Fluorescent dyes are the best liquid media for lasers;
their excited energy levels are populated either by flash lamps or by lasers.

07
In solid state lasers, population inversions are brought out by implanting impurities
(which give the laser action) within a. host material, such as a crystal or a glass and then
exciting them with a suitable light. The impurity concentration is usually in the range of
0.01-3.0 per cent. In most of the solid state lasers, the impurities are in the form of ions in
which the energy states are shielded from the surrounding atoms so that the energy levels
are narrow. A flash lamp is used to excite the ions to a large number of upper energy levels.
The excited ions decay quickly to the met stable upper level where they stay for a
considerable time (of the order of milliseconds) before terminating at the lower energy
level, leading to the stimulated mission no flash radiation. Inversions in semiconductors
are produced when a p-n junction is created by joining two slightly different semi-
conducting materials, viz., n- and p-type materials (similar to a transistor). Then-type
materials have an excess of electrons whereas the p-type materials have an excess of
holes (missing electrons). When they are joined, excess electrons of the n-type materials
are pulled over into the p-region causing the electrons and holes in those regions to
recombine and emit radiation. If an external electric field is applied in an appropriate
direction, by applying a voltage across the junction, more electrons and holes can be
pulled together causing them to recombine and emit more radiation producing inversion

1.1.6 Laser Beam Properties

The use of a laser for various applications depends upon the beam properties of laser,
such as direction, divergence, and wavelength or frequency characteristics, which can be
adjusted by the laser components. The features affecting the beam properties of laser
include the size of the gain medium, location, separation and reflectivity of the mirrors of
the optical cavity, and presence of losses in the beam path within the cavity. Some of
these features determine the unique properties of the laser beam, referred to as laser
modes. The laser modes are wavelike properties relating to the oscillating character of the
beam as the beam passes back and forth through the transverse modes which give rise to
a complex frequency and spatial structure within the beam which otherwise appears as si.

08

2. Lasers -Their Types & Characteristics

 The first laser action was demonstrated in a ruby crystal by Maiman, in 1960. Since then,
a large number of materials in various media have been found to give laser action at
wavelengths in the visible, ultraviolet, and infrared regions. These include various gases,
solids, liquid, glasses, plastics, semiconductors, and dyes. In addition to the ruby crystal,
many other crystals doped (introduced as an impurity) with rare earth ions have light
been found to give extremely good laser output The crystals are grown in specially
designed furnaces with the desired compositions and then cut and polished into
cylindrical laser rods

with the faces optically flat and parallel to each other. The numerous types and designs of
lasers are steadily increasing and can be broadly classified according to their production
techniques. The broad categories are:

(i) Optically Pumped Solid-State Lasers

(ii) Liquid (Dye) Lasers
(iii) Gas Lasers
(iv) Semiconductor Lasers
(v) Free Electron Lasers
(vi) X-ray Lasers, and (vii) Chemical Lasers

2.1 Optically Pumped Solid-State Lasers

2.1.1 Ruby Laser

Ruby laser is historically the first one to be discovered;

It gives laser radiation on a pulsed length (1 nm = 10 -9
m). It consists of a ruby rod xenon flash tube, a suitable
cavity to reflect the light from the flash tube to the ruby
rod, and a high-voltage power supply to give electrical
energy to the flash tube. Maiman's laser set-up is
shown in Fig. 3.1.
During his experiment, Maiman found that the ideal
composition for the ruby crystal is five atoms of chromium for every ten thousand atoms
of aluminum, i.e., a concentration of 0.05 percent. The ruby rod used was 4 cm long and
1/2 cm in diameter and the ends were ground to a high degree of flatness and parallelism.
One end was silvered making it a mirror (almost 100 percent reflective) to reflect all the
rays of light striking it. The other end of the rod was partially silvered; the laser beam
was emitted through that end. The ruby rod was surrounded by a helical xenon flash lamp
and both of them were held inside a cylindrical cavity, coated with a

09
10

10
10 cylindrical cavity onto the ruby rod, thereby exciting the chromium atoms which were
responsible for the laser action

The ruby laser is a three-Level system (Fig. 3.2)

since only three energy levels are involved in
the process of stimulated emission. The
depopulation of the ground state for population
inversion is achieved by exciting the atoms of the
ruby crystal with intense light from a xenon
flash lamp. Thus the atoms are excited from the
ground state (level 1) to an upper state (level 3)
by means of absorption. From the energy level
3, the atoms are transferred to energy level 2
without emitting radiation (non-radiative
transfer). The energy level 2 is called met stable
level since the atoms stay at this level for a longer
interval of time. Finally, the atoms return to the
ground state from the met stable level through the
process of stimulated emission giving rise to an
intense laser light at 6943A. The laser beam
comes out in the form of a pulse of very short
duration (about a millisecond). The continuous
wave operation of the system is very difficult to
achieve. Only 1 to 2 per cent of the input is
utilized to obtain the laser action. The rest is
dissipated as heat and is therefore wasted. In Q-
switched mode, the power up to 500 MW has
been achieved. Since this laser requires consider
able input energy to give laser action, it is now
being used only for limited applications in the
areas of holography, high speed photography,
etc.

2.1.2 Rare Earth Ion Lasers

A large number of lasers have been discovered using the rare earth ions doped in suitable
crystal lattices or glasses as the active elements.
These lasers are based on a system in which four
energy levels are involved to produce stimulated
emission. The laser action takes place between
the met stable level and a lower energy level
which is slightly above the ground state
(Fig.3.3). Due to this advantageous situation,
population inversion is achieved easily. Of
the 14 rare

11
 earth elements used, triply-ionized neodymium has been found to hp the
most
important. Absorption bands suitable for optical pumping are relatively abundant. Strong
laser emission is obtained in the near-infrared region at 1.06 micrometer 1wavelength
with continuous power of over 1000 Wand with -pulsed power as high as several MW (1
MW = 10 W). The most prominent among the neodymium lasers are ND: YAG
(Neodymium Yttrium. Aluminium-Garnet) and Nd: Glass (Neodymium in Glass) lasers.

2.1.3 Nd: YAG Lasers.

YAG is formed from a mixed oxide system having a composition of Y 3Al5OI2. Using the
Czochralski method, the crystal is grown in a specially designed furnace. Dipping a
rotating seed into a crucible of molten material and withdrawing it at a constant speed.
Iridium crucible is used because of the high melting point of YAG (1910-1970°C). The
optimum concentration of neodymium in YAK is about one percent.

The YAG crystal growth difficulties limit the size of the laser rods to approximately 1 cm
in diameter. However, the YAG host has the advantage of having a relatively high
thermal conductivity to dissipate the heat generated, thus allowing these crystals to be
operated at high repetition rates of the order of many pulses per second. With a
continuous source of excitation like a tungsten lamp or krypton arc lamp, a continuous
laser output of about 1 kW power could be obtained.

Due to these excellent properties, Nd: YAG laser is extensively used in many industrial
applications like the drilling of holes in solid objects, welding of metals and alloys, etc,
and also in medical applications like eye surgery, treatment of cancer, etc.

2.1.4 Nd: Glass Lasers

Nd: glass is an important laser material for high-energy applications. It affords

considerable flexibility in size and shape and can be obtained in large homogeneous
pieces. Glass is a compound of oxides; non-metal oxides, such as silicon dioxide,
phosphorus pentoxide, and boron oxide are its main constituents. It is possible to obtain a
large variety of properties due to the existence of different metal oxides, which alter the
structure in various ways. These components as well as the laser activators are mixed and
heated to melt in a furnace when the required laser glass is formed.

The major disadvantage of glass is that it produces inhomogeneously broadened lines

which are wider than those found in crystals. This raises the threshold, as a larger
Inversion is required for the same gain. Another disadvantage of glass is its pulsed mode,
which are used in the military and material processing applications. Glass lasers with
amplifier chains are capable of producing very high energy and are therefore used in laser

12
Another type of neodymium laser is the GSGG: Cr3:Nd3+ laser. It uses a crystal of
gadolinium-scandium-gallium garnet, co-doped with chromium and neodymium ions.
Since chromium has good absorption bands in the visible region, the pumping efficiency
is increased; and due to efficient energy transfer from chromium to neodymium, the CW
laser action is achieved much more easily than in Nd: YAG or Nd:Cr: YAG lasers

2.1.5 Tunable Solid-State lasers

In these four-level solid-state lasers, laser transitions of the transition metal ions like Cr3+,
Ti3+, and Ne3+, are employed that terminate on excited vibration levels of the ion in the
host lattice. As with the ruby (Al2O3) laser, the alexandrite (BeAl2O4) laser employs Cr3+
ion, and the laser transition can terminate on a variety of final vibration states, giving
laser radiation at several wavelengths in a given spectral range. At the other (output) end,
a diffraction grating is operated to obtain the laser radiation at the desired wavelengths.
Thus, the alexandrite laser is tunable from 700 to 818 nm, i.e., in the extreme red region
and has pulsed output energies similar to those in the ruby laser, The titanium sapphire
(Ti:Al2O3) laser, with titanium as the active ion in the host lattice of the sapphire, has a
broader tunability (from 600 nm to beyond 1, 1 µm (i.e. infrared region). It has operated
continuously at power levels up to 1 7 Wand has given laser pulses of a few hundred mill
joules.

2.1.6 Liquid (Dye) lasers

Liquid lasers are similar to solid-state lasers in that they consist of a host material (in this
case a solvent such as alcohol} in which the laser (dye} molecules (such as rhodamines
or coumarins) are dissolved at a concentration of one part in ten thousand. Dyes exhibit a
very high degree of fluorescence, i.e., when the dye is exposed to ultraviolet light, it
glows with characteristic color depending on the nature of the material. Different dyes
have different emission spectra or colors. As a result, dye lasers cover a broad
wavelength range from the ultraviolet at 320 nm to the infrared at about 1500 nm, A
unique property of dye lasers is the broad emission spectrum (typically 30-60 nm) over
which the gain occurs. When this broad gain spectrum is combined with a diffraction
grating or a prism as the cavity mirrors, the dye laser output can be a very narrow
frequency beam (10 GHz or smaller). Frequency tuning over even larger ranges is
accomplished by inserting different dyes into the laser cavity.

13
Dye lasers are available either in pulses (up to 50-100 MJ) or as continuous output (upto
a few watts) in systems that are pumped by either flash lamps or other lasers, such as
frequency-doubled or tripled YAG lasers or argon ion lasers. Since the dye degrades
slightly during the excitation process, most of the dye lasers are arranged to have the dye
circulated from a much larger reservoir. A typical dye laser set-up is shown in Fig.3.4.

The dye lasers are used mostly for applications where tunability of the laser frequency is
required either for selecting a specific frequency that is not available from one of the
solid-state or lasers or for studying the properties of a material when the laser frequency
is varied over a wide range. Therefore, the dye laser becomes an important tool for
spectroscopy, photochemistry, pollution monitoring, Isotope separation, etc. Another
important application of dye lasers is for producing ultra-short optical pulses by a
technique known as mode-locking. In this process, the longitudinal modes of a dye laser
(as many as 10,000) are made to oscillate together (in one phase) causing the individual
pulses as short as 50 femtoseconds (5 x 10-14 s) to emerge from the laser. These short
pulses find application in studying very fast processes in solids and liquids and perhaps
also in optical communication. The dye lasers are less expensive than the solid-state
lasers and are relatively easy to maintain for regular operation.

2.1.7 Gas Lasers

The gas lasers have a gas or a mixture of gases as their light-amplifying substance.
Helium-neon, argon ion, and carbon dioxide lasers are the most widely used gas lasers.
Javan, Bennett, and Herriott succeeded in demonstrating the first gas laser towards the
end of 1960-a a few months after Maiman discovered the ruby laser. They used a helium-
neon mixture (90 percent helium and 10 percent neon) as the active material. In most
cases, the gas is contained in a glass or quartz tube about 25-100 cm long and the gas
molecules are excited.d in an electric glow This energy is provided by applying a high
voltage between electrodes located w.gaseous- medium to accelerate the electrons to the
14

14
2.1.8 Helium-Neon Laser

The helium-neon laser is the most widely used of all lasers mainly because it is much
cheaper than the solid-state lasers and yields highly coherent radiation required for many
applications. In this system (Fig. 3.5), an electrical discharge is given in helium contained
in a discharge tube at a pressure of about 1 torr with an admixture of neon at about 0.1
torrs. The discharge excites the helium atoms to their first excited level above their
ground state. Since the neon atoms also have an excited level very nearly equal to that of,
the helium atoms, the excited energy of the helium atoms is transferred to the neon atoms
by resonance transfer due to collisions between them. These excited states decay
radiatively to lower energy neon states giving rise to continuous laser emission in the red
region at 632.8 nm with output power in the range of milliwatts (10-3 W). The helium-
neon laser is also capable of giving laser radiation at a few more wavelengths invisible
and infrared regions. This laser is used in surveying, engineering construction,
supermarket checkout scanners, printers, holography and many other such applications.

2.1.9 Argon and Krypton Ion Lasers Carbon Dioxide Laser

The carbon dioxide laser was discovered in 1963-64 by CKN Patel, a brilliant Indian
scientist working at the Bell Laboratories, USA. It is undoubtedly a very important laser
because of its high efficiency and high power capacity. It gives laser radiation at a 10.6-
micron wavelength in the infrared region. It is a molecular gas discharge with the laser
action taking place between two vibrational levels of the carbon dioxide gas.It can be
operated in both continuous and pulsed.

15
Because of the heat generated due to continuous excitation, the power available from this
laser is limited to about 75 W per meter of tube length. To overcome this difficulty, the
gas is made to flow at high velocity through the discharge region, which carries away the
heat generated rapidly. Such fast-flow carbon dioxide lasers are now commercially
available, giving up to kW continuous power. In a pulsed mode, the pressure of the laser
gas can be increased to 1 atm or even higher. Because of the higher density of molecules,
it becomes possible to obtain very high power from the laser, but in short pulses only.
Such lasers can give a peak power of a few megawatts in a laser pulse of about a
nanosecond duration.

The carbon dioxide laser is used for a wide variety of applications, including eye and
tissue surgery, welding, cutting and heat treatment of materials, laser fusion, and beam
weapons. Rocks and granites crumble into pieces with a 1.2 kW carbon dioxide laser.
One day, such a laser may be used to drill underground tunnels.

2.1.10 Excimer Laser

The excimer lasers are pulsed gas lasers that use a mixture of a rare gas and a halogen as
the active medium. Excimers are molecules that exist only in the excited state; the
population of the ground state of the molecule is always zero As a result it is relatively
easy to obtain population inversion and get high. Efficiency. , The excimer lasers operate
primarily In the ultraviolet region in mixtures of rare gases (argon, krypton, or xenon)
with halide molecules chlorine or fluorine). These include argon fluoride laser at 193 nm,
krypton fluoride laser at 248 nm, xenon chloride laser at 308 nm, and xenon fluoride laser
at 351 nm. A schematic diagram of t h e excimer laser is shown in Fig. 3.6.

16
The excimer lasers typically produce short pulses of peak power of 10-20 MW with
repetition rates of up to 1000 pulses per second. These lasers are very efficient ( up to 50
percent) and provide useful energy in the wavelength regions where other types of
powerful lasers are not available. The laser gas is mixed With helium gas so that the
mixture has a pressure of about 2-4 atm. Excitation occurs by electron dissociation and
ionization of the gas molecule to produce argon, krypton, or xenon ions. These ions react
With the halide molecules pulling off one of the atoms of that molecule to create an
excited diatomic molecule, also called The excimer molecule. The excimer lasers are
widely used for laser surgery, drilling of holes in metallic objects, pumping of dye lasers,
and lithography.

2.1.11 Semiconductor lasers

The semiconductor or diode lasers are the smallest of all known lasers; they have a size of
a fraction of a millimeter. The laser consists of a semiconducting crystal, such as gallium
arsenide, lead selenide, etc, with parallel faces at the ends to serve as partially reflective
mirrors. The entire laser package is very small and can be incorporated into an integrated
circuit board if required.

A semiconductor, as the name implies, is halfway between a conductor and an insulator

(non-metal), so far as its electrical conductivity is concerned. The semiconducting
materials containing gallium and arsenic compounds have been found to generate infrared
rays when the current is passed through them. This implies that these semiconductors
convert electrical energy into photons. But, these were ordinary incoherent light rays and
were not produced by the laser action, However, when the gallium arsenide crystal is
through it, the laser action does take place. Many semiconductors serve as laser materials
and they have been made to 'lase' under the stimulation of electricity instead of light
which is used for the other solid--

material is made to have an excess of electrons, which, the material can be made to have.

17
The semiconductor laser consists of a tiny block (about one square millimeter in area) of
gallium arsenide (Fig. 3.7). When the p- and n-type layers are formed in an intimate contact,
the interface becomes a p-n junction. When direct current is applied across the block, the
electrons move ii across the junction region from the n-type material to the p-type
material, having a n excess of holes. In this process of dropping of the electrons
into the holes, recombination takes place leading to the emission of radiation. The
photons traveling through the junction region stimulate more electrons during the
transition, releasing more photons in the process. The laser action takes place along the
line of the junction. Due to the polished ends of the block, the stimulated emission grows
enormously and a beam of coherent light is emitted from one of the two ends. With a
gallium arsenide laser, a continuous beam of a few militates power is easily obtained.

The semiconducting lasers are also called junction lasers or junction diode lasers because
they produce laser energy at the junction of two types of impurities in a semiconductor.
They are also called injection lasers because electrons are injected into the junction
region.

The technology of semiconductor lasers has obtained output in the range of tens of
milliwatts. and with operating wavelengths, lasers have been

In weight with compact units and requiring little auxiliary, they have found a large
market as reading devices for compact disc players.

18
2.1.12 Free-Electron Lasers

Free-electron lasers, discovered recently, are significantly different from any other type
of laser in that laser radiation is not obtained by discreet transitions in atoms or molecules
of a material. Instead, a high-energy beam of electrons (of the order of one million
electron volts (meV)) is directed to pass through a spatially varying magnetic field that
causes the electrons to oscillate back and forth in a direction transverse to the direction of
their beam, at a frequency related to the energy of the electron beam.

This oscillation causes the electrons to radiate at the oscillation frequency and to
stimulate other electrons also to oscillate and radiate at the same frequency, in phase with
the original oscillating electrons thereby producing an intense beam of light emerging
from one end of the device. Mirrors can be placed at the ends of the magnetic region to
feed the optical beam back through the amplifier to stimulate more radiation and cause
the beam to grow. The frequency is tunable by variation of electron energy and the laser
radiation can be generated at any wavelength from the ultraviolet to infrared regions.

A great advantage of the free-electron laser is that a high average output power of the
range of a few kilowatts can be obtained in the continuous mode. Although still more of a
laboratory curiosity, it shows good promise of high energy applications especially in the
medical field.

2.1.13 X-Ray Lasers

In contrast to teasers operating in the visible and infrared regions, x-ray lasers pose a
considerable challenge to present-day technology. In the x-ray region, i.e., below a few
nanometers (10-9m) wavelengths, the stimulated emission from the medium. For these
reasons, the x-ray lasers use a subsidiary laser or a short and intense laser pulses have
produced laser emissions at 15.5 NM. Current research involves efforts to improve the
very low efficiency of X-ray lasers as well as to develop new potential X-ray

19
Chemical Lasers

In the search of alternative methods to the convention excitation of materials With light
sources, scientists have found that the Intense light produced by reactive chemicals can
be used for laser excitation. A chemical laser produces a high energy beam from the
energy released in the reaction of two or more chemicals. It converts the free energy
produced by a chemical reaction into a specific excitation of some product species Such
chemical reactions can be brought about with the aid of gamma rays, electrons, photons
etc. Flames can also be used as a source of excitation to Initiate teaser action. Explosive
gas mixture, which may also be used to excite laser radiation in the gas itself, is another
pumping source.

Chemical laser is potentially a very efficient compact device. In a typical chemical laser,
nitrogen is heated by an electric arc and mixed with sulphur hexafluoride. The heated
mixture is then forced through a set of nozzles and hydrogen is injected into the exhaust.
Lasing takes place when the exhaust passes between two mirrors

The laser emission was obtained in the infrared region with the help of the energy
produced by the reaction of hydrogen and chlorine. The hydrogen fluoride laser is another
very powerful chemical laser which produces laser radiation at wavelengths from 2.6-3.5
µm. A mixture of hydrogen and fluorine is used in this laser. When the fluorine molecule
is dissociated optically or by discharge or by electron beam pumping, a chain of chemical
reactions takes place reducing the vibrationally-excited hydrogen fluoride molecule.
Since there are no hydrogen fluoride molecules in the lower state in the beginning, the
population inversion is easily achieved and the laser action takes place. The deuterium
fluoride laser is another important chemical laser. Its working is similar to that of the
hydrogen fluoride laser. It produces laser radiation in the region 3.5-4.1 µm.

20
04 Laser Application I: Defense
2.2 Laser Range Finder

To knock down an enemy tank, it is necessary to range it very accurate!y. Because of its
high intensity and very low divergence even after travelling quite a few kilometres, laser
is ideally suited for this purpose. The laser range finders using neodymium and carbon
dioxide lasers have become a standard item for artillery and tanks. These laser range
finders are light weight and have higher reliability and superior range accuracy as
compared to the conventional range finders.

The laser range finder works on the principle of a radar. It makes use of the characteristic
properties of the laser beam, namely, monochromaticity, high intensity, coherency, and
directionality. A collimated pulse of the laser beam is directed towards a target and the
reflected 1ight from the target is received by an optical system and detected. The time
taken by the laser beam for the to and fro travel from the transmitter to the target is
measured. When half of the time thus recorded is multiplied by the velocity of light, the
product gives the range, i.e., the distance of the target.

The laser range finder is superior to microwave radar as the former provides better
collimation or directivity which makes high angular resolution possible. Also, it has the
advantage of greater radiant brightness and the fact that this brightness is highly
directional even after travelling long distances, the size of the emitting system is greatly
reduced. The high monochromaticity permits the use of optical band pass filter in the
receiver circuit to discriminate between the signal and the stray light noise.

21
A typical laser range finder can be functionally divided into four parts: (i) transmitter, (ii)
receiver, (iii) display and readout, and (iv) sighting telescope. An earlier version of a laser
range finder is schematically shown in Fig. 4.1. The transmitter uses a Q-switched Nd:YAG
laser which sends out single, collimated and short pulse of laser radiation to the target. A
scattering wire grid directs a small sample of light from the transmitter pulse on to the
photodetector, which after amplification is fed to the counter. This sample of light starts
the counter. The reflected pulse, received by the telescope, is passed through an
interference filter to eliminate any extraneous radiation. It is then focused on to another
photodetector. The resulting signal is then fed to the counter. A digital system converts the
time interval into distance. The range, thus determined by the counter, is displayed in the
readout. The lighting telescope permits the operator to read the range while looking at the
target

Special circuits have been used to eliminate Spurious signals with the help of range
gating and to make the use of laser range finder Possible under all weather conditions for
which the targets can be seen visually through the sighting telescope. The modern
versions of the laser range finders Use either high repetition pulsed Nd:YAG laser or
carbon dioxide laser with range gating system. In ranging a target about 10 km away
using these systems, an accuracy within 5 m is easily obtained. The laser range finders of
medium range (up to 10 km) are used in several Defence areas, including

• Tank laser range finder for artillery, an armoured vehicle, or a truck.

• pulses. With this, it is possible to which transmit and receive audio/visual
communications, or pinpoint targets with a hand-held laser, even from unsteady
around by the rolling seas. There are no separate tripods, unwieldly power
packs,

22
2.3 Underwater Laser

Lasers can also be used as a source of underwater transmission. For this purpose, a laser
giving radiation in the blue-green region is most suitable as the transmission in this
region is maximum for sea water. The attenuation in underwater transmission is due to (i)
absorption by materials in water, (ii) scattering by suspended particles, and (iii) variation
in optical density along the light path. The blue-green lasers have assumed much
importance in the systems related to naval applications.

At present, the submarines have to rely on a sonar to find the enemy crafts and to avoid
the underwater objects. This has serious limitations. The whales, dolphins and other
marine life give false signals. A typical sonar cannot give a well-defined picture because
the sonar beam is broadened or scattered by sea water. A difference in the saltiness of
water can cause the sonar beam to bend and make the target appear where it is not.
Another problem of using sonar is that it gives away to the enemy the position of the ship
from which it is transmitted.

Lasers can be used efficiently for ranging and detection

23
of underwater objects. For this purpose, a frequency doubled Nd:YAG laser or an argon
ion gas laser or a Raman shifted xenon chloride laser is used. A schematic diagram
of an
.underwater ranging and viewing system is shown in Fig. 4.2. It consists of the laser
transmitter which sends high power laser pulses of about 10 ns duration to the target at
the rate of 30 to 50 per second through a beam splitter and a diffuser small amount of the
laser light reflected by the beam splitter is made to fall on the photodiode the ranging and
display circuit to start the time interval counter. The reflected light from the target is
collected by telescopic optics after stray radiation is eliminated by an interference filter.
A range gating circuit helps to avoid unwanted echoes The reflected pulse from the target
is intensified by the image intensifier and the output is fed to image orthicon, which gives
the display of the object. In this way, both the range and the image of the target are
obtained. With high power release of several megawatts power, underwater ranging is
possible up to 500 m in clear water.

Lasers can also be used for communication between submarines ensuring absolute
privacy and in guidance systems for torpedoes and other unmanned underwater vehicles.
Recent underwater laser communication has been established via satellite, i.e., from gr

24
2.4 Laser-Guided Anti-Tank Missile (ATM)

A missile can be guided and controlled by an infrared beam emitted from a laser, with
extremely small divergence. This can be achieved in four ways:

(i) The laser beam is used to illuminate the target tank; the anti-tank missile (ATM)
then homes on to the target,as the latter has .become a source of back-scattered
radiation.
(ii) The laser beam is used to provide guidance instructions to the missile, i.e., it
provides the command link.
(iii) The missile rides the laser beam which is kept pointing along the collision course to
the target.
(iv) The missile itself carries a laser scanner and seeker for active homing on to the target

In the first case, the laser target designator is a pulsed Nd:YAG laser. The laser beam is so
modulated that the receiver, a four quadrant detector in the missile, is able to calculate
any divergence of the missile trajectory from the beam axis and correct the deviation by
altering the fins of the missile. The guidance unit consists of both optical and electronic
equipment. This enables the gunner to aim the infrared guidance beam for firing the
missiles.

The system in which the missile is a beam rider designed to ride the laser pointing in the
direction of the target, is more attractive. n missile can carry four detectors at the wing
tips looking towards the rear of the missile. The detectors determine the central axis of
the laser beam and keep the flight path of the missile along it. The wavelength of the laser
should be such that is the least absorbed by the plume of the sustainer motor. Thus in a
laser designator, the laser by virtue of its narrow beam illuminates a chosen target. A
receiver in a bomb or a missile seeks the target illuminated from the scattered laser
radiation and homes on to it. In the Vietnam war an in the recent Iraqi war, the Americans
used laser guided missiles with pinpoint accuracy to destroy the enemy targets.

2.5 Laser Radar (Lidar)

When the laser beam is used for a radar application, it is called lidar. The details,
which could not be achieved earlier with microwave radars, can now be obtained with
lidar.
Besides, the laser beam can be focused with lenses an mirrors easily whereas microwaves
need huge antenna for focusing. As a beacon or a radar, the advantages of utilising small
antenna and components are obvious. With a lidar, the dimension and the distance of the
target can be obtained with higher accuracy, which is not possible wit! the conventional
microwave radar. The lasers used in lidars are of carbon dioxide, Q-switched
neodymium,
25
The great advantage of the use of carbon dioxide lasers for radar application is their
capacity to produce high power output with requisite The spectral purity. The coherent
carbon dioxide laser tips radar functions essentia1 like a coherent microwave radar except
for the fact that the carbon dioxide laser beam has a frequency of a few thousand times
more than that of the X-band radar and at it a sharp beam width of a few microradians.
The high frequency of the carbon dioxide laser also produces high Doppler shift even
from slow-moving targets. The fine beam width and high Doppler the shift give the
carbon dioxide laser an unparalleled imaging capability. This radar system is used for and
measuring radial velocities to track low-flying aircraft and slow-moving objects. Since
the laser beam is very much attenuated by rain, fog, or snow, the lidar can perform well
only in good weather conditions.

2.6 Ring Laser Gyroscope

The ring laser gyroscope is an extremely useful instrument for sensing and measuring
very small angles of rotation of the moving objects. It has now replaced the mechanical
gyroscopes used in most of the aircraft (both civil and military) he and also in long range
guided missiles. The main advantages of the ring laser gyroscope are: (I) non-existence of
moving parts, (ii) high g capability, and (iii) higher reliability as compared to the
mechanical gyroscope. In addition, the laser gyroscope is capable of wide dynamic range
and rapid reaction time, the characteristics required for missile guidance.

26
The ring laser gyroscope basically consist of a ring cavity around which two laser light
beams travel in opposite directions. The operation of the ring laser gyroscopes is based on
the so called Sagnac effect by which rotation of an object is sensed by an interferometric
technique. A schematic diagram of the ring laser gyroscope.

In a triangular cavity of a quartz block, laser beam is split into two light beams with the
help of suitable mirrors. These two light beam travel in opposite directions in the same
path of the cavity, one in the clockwise and the other in the anti-clockwise direction. The
two light beams then pass through a beam splitter and a beam combiner, behind which a
readout detector is placed. If the cavity which is acting as an interferometer is stationary,
the two light beams travel the same distance in the opposite directions without any path
difference and hence no interference takes place. However, if the block is rotated
clockwise about an axis through the centre and perpendicular to the plane of the
interferometer, the beam travelling in the clockwise direction travels a path length
slightly more than the beam travelling in the anti-clockwise direction. When these two
light beams recombine at the beam combining prism, interference takes place due to the
path difference; the interference fringes displaced in the field of view are proportional to the
amount of rotation of the block. The laser gyroscope uses a helium-neon gas laser to
generate monochromatic radiation in the two directions inside the triangular quartz block.
Two photodetectors sense the direction and the rate of rotation. The output is proportional
to the input. angle. The whole system is a single plane, rate integrating gyroscope and is
capable of measuring rotation rates of the order of 1/10,000 degree/hour.

The main use of the ring laser gyroscope is for inertial navigation. It is being used in
inertial guidance of aircraft, ships, and missiles; flight control; and gun-fire pointing.
Both Honeywell and a Litton Industries, USA, the manufacturers of the ring laser
gyroscopes, have introduced them in the Boeing 757 and 767 and Airbus A 310, now in
production. These gyroscopes are ideally suitable for the various guided missile applicat

27
2.7 Air Reconnaissance

Lasers can be used as a secretive illuminators for aerial reconnaissance during night with
high precision. Earlier it was done using a camera, equipped with either magnetic flares
or powerful strobe lights with their cumbersome power supplies. For this purpose, a
helium- neon laser or a gallium arsenide semiconductor laser is used. Two properties of
the laser, namely, its narrow beam and its radiance or brilliance are of importance in this
particular application.

The block diagram of the laser camera is shown in Fig. 4.4. One of the beams passes
downwards through a six-sided prism scanner towards the earth. The prism scans through
a selected angle at right angles to the direction of the flight of the aircraft. The other beam
passes through a Pockels cell modulator. On emerging from the modulator, the beam
strikes the prism scanner and is then reflected towards and recorded on the film.

The laser beams reflected from the target area are picked up by a Schmidt lens, which
images the light on to a photodetector. The video output of the photodetector,
corresponding to the reflectivity of the observed terrain, drives the modulator. Thus, the
returned beam modulates the original beam. The pictures thus obtained are comparable in
resolution with those taken under daylight conditions. Thus, the enemy targets can be
photographed at night under high secrecy during the flight of the aircraft. The laser
camera system was tested successfully by the United States Air Force Tactical Air
Reconnaissance Centre.

2.8 Communications

A very useful and interesting application of laser is in the field of communications,

which takes advantage of its wide bandwidth and narrow beam rtant. The infrared region
is pref

28
 A particular aspect of laser transmission, which makes it preferable to the ordinary radio
waves for military purposes is the strict secrecy provided by the narrow beam width.
Since no unwanted reception outside the narrow bundles of rays is possible, a high degree
of secrecy can be maintained between two points, and thus, an interception-proof
communication network can be realised. Besides, laser communication system is immune
from jamming and from interference by spurious radio noise.

The optical laser has a great potential for use in long distance communication. Since the
capacity of a communication channel is proportional to the frequency band width, at
optical frequencies, the information carrying capacity is many times more than that is
possible at lower frequencies. This and the fact that the laser is a generator of highly
coherent beams which are powerful and sharply directed, make it ideally suited for
communications.

In this regard, microwave technique offers direct competition to the laser as it has been
perfected already to a high degree. Moreover, the optical frequency waves suffer a
considerable disadvantage in case of atmospheric transmission since they are attenuated
considerably by snow fog, and rain. Therefore, the laser communication through the
atmospheric medium is effective only in clear weather conditions, with no obstacles
interrupting the beam between the transmitting and the receiving stations.

Figure 4.5 shows the principle behind the long distance communication system, which
involves multiplexing the simultaneous transmission of different messages over the same

29
pathway. For example, a channel for transmitting an individual human voice requires a
frequency band extending from 2000 to 4000 cycles per second. For modulation of the
signal without the addition of any noise, the carrier wave should be of a very narrow
spectral width. This single frequency carrier wave is then successively modulated by a
large number of voice signals to create a new composite single wave. With the help of
special electrical networks, several broad communication bands are combined for
simultaneous transmission over a single intensity pathway. On the other side of the line, a
similar network separates the single signal into its component broad bands which are
demodulated into individual telephone calls.

Thus considerable economy and efficiency in communication is achieved through

multiplexing process. Since an individual communication channel requires the same
bandwidth regardless of the region of the spectrum in which it is located, it is quite
obvious from the above that the visible and near-infrared laser frequencies, which are
about 1,000,000 times the frequency of the millimetre waves, offer great economy for
communication.

For communication purposes, the laser beam is modulated by the signal. At the receiving
station, the modulated beam is demodulated (detected) to separate the required signal
from the laser beam (carrier). The output current, which varies with the intensity of the
signal, is amplified and then fed to the speaker.

Most of the optical modulators devised so far are based on the variations in the refractive
index of the substance used according to the signal wave. The continuous laser output
from a laser passes through a polarisation modulator (KDP crystal) as shown in Fig. 4.6.
Ring electrodes are placed on the crystal and an electric field proportional to the signal
wave is applied to the crystal, parallel to the axis. Due to the change in refractive index of
the crystal, which follows the electric signal, there is change in polarisation of the light
beam. As a result of this, the intensity of the light coming out of the analyser also
changes, according to the signal.

The laser beam from a semiconductor laser can be directly modulated by varying the
85009000 Å (one Å= lxl0-8 cm). This being the spectral region of the gallium arsenide
lasers, the silicon photodiodes can be used as sensitive detectors in that region.

Demodulation by optical heterodyne detection is done by superposing on the incoming

incident signal, a beam of light from an unmodulated laser called a local oscillator and.
When this is fed to an audio speaker, the input signal of the communication is
reproduced

30
Laser communication through open atmosphere is possible only when there is line of
sight between the transmitter and the receiver and that too in good weather conditions. To
circumvent these difficulties, laser communication through the medium of optical fibre
has been achieved in recent years. This aspect has been treated in Chapter V.

2.9 Anti-Missile Defence System (Star Wars)

In an antimissile defence system, laser is used to dispose the energy of warhead, not by
vaporising or melting it, but by partially damaging the missile, say by drilling a hole.
Tremendous energy is required to completely burn the missile, which is not practicable. If
a guided vane of a missile is fractured, several vibrations will be developed in the air
frame thereby disintegrating major sensitive portion of the missile.

Two types of anti-missile defence systems have been visualised. One such system, laser
kill system is completely earthbound (Fig. 4.9). Here, an early warning microwave radar
gives a rough position of the approaching missile. Then a lidar aligned to the target by the
tracking radar gives the precise position of the missile. This data is fed on to another high
intensity laser beam which actually does the killing. To exploit the laser's killing
capability, a high speed servo system and a complex focusing system are essential.

31
The other anti-missile defence system is the orbiting space station, equipped with
detecting, tracking and killing laser devices. An infrared homing system on the laser
weapon is used to close on an enemy vehicle and then fire a high energy laser beam.
Firing by laser weapons would not change the positional or altitude stability of the space
station. It is predicted that the lasers would ultimately make inter-continental ballistic
missiles (ICBM's) obsolete.

There are, however, many limitations in the utilisation of laser in its anti-missile role. The
power required is very prohibitive and as a result huge power stations are required for the
operation. At present, huge power of more than 100 kW in the continuous mode is being
obtained from the gas dynamic carbon dioxide lasers and some other chemical lasers,
developed in the US and Russia. This amount of laser power is sufficient to destroy an
enemy vehicle or a missile.

The SDI or Star Wars is the US programme aimed at defending itself and its allies against
the ICBM strikes through space. The concept of strategic defence is concentrated at a
three- layered defence system in which the enemy missile can be destroyed in the boost,
or the mid-course, or terminal phase. Each layer of defence employs several alternatives
of weapon systems. Laser is one such important system.

2.10 Laser Proximity Fuze

The proximity fuze, developed in the US using a solid-state laser, detonates the missile
warhead when it comes within the range of its target. The higher manoeuvrability of the
missile is expected to improve its performance a great deal in close in aerial combat. It is
also claimed that the proximity fuze and the warhead will enable the missile to destroy
its

32
2.11 Laser Beacon

The present infrared light sources, being used as ground beacons to identify the ground
points, are inefficient and not much reliable. Using a lensless diode array, a laser beacon
can made multi-directional. The laser beacons are light in weight, efficient and have long
life. Another advantage is that the pulses can be used ground beacons so that the
airdropping of supplies can be done at the given locations efficiently

2.12 Weapon Firing Simulator

If we take into account the cost of ammunition and large land that is required to fire it,
basic training of the tank gunners is very expensive. A simulator technique, which does
not sacrifice the acquisition of the basic skills during trials, has been developed in which
the main weapon has been replaced by a laser. The technique is known as the weapon
firing simulator.

The simulator, installed in the machine gun mount of the vehicle, produces a single burst
intense red light when the firing circuit of main weapon is activated. On seeing this bright
spot of light, which is visible momentarily in optical system of the vehicle, the trainee is
able to lay his gun sights accurately to track the targets. It also enables one to check the
accuracy and proficiency of the crew in operating the vehicle's main weapons system.

33
 04 LaserApplicationsII: Civil
Since a laser beam can be controlled and located much more precisely than an arc or a
flame, the intense heat generated by its absorption in various materials is used for high
precision welding, drilling, and micromachining. No distortion is caused in the material
welded by laser because it produces minimum shrinkage. Traditional welding has its
limitations; certain materials cannot be welded by the conventional means. Laser
technology has enabled reliable welding of gold with silicon and germanium, aluminium
with nickel, tantalum with copper and several other metals used in electronic equipment.
With laser, it even possible to join metallic and non-metallic material.

Introduction of microcircuits into electronic equipment and thin film technology

necessitated reliable spot welding like microwelding used in microelectronic circuits and
watch parts. In such cases where heat-affected zone is minimum and welds of microsize
are required, spot welding of high quality can be achieved by lasers without causing any
damage to the delicate metals and ceramics being welded. Successful laser welding of
high strength alloy steels, carbon-rimmed steel, tin-plated mild steel, etc has been
achieved 2-5 kW continuous wave carbon dioxide laser.

2.13 Laser Drilling

Laser drilling of metals is based on a face-heating phenomenon. The absorbed intensity is

transformed into heat within the penetration depth of laser radiation. And when the
illuminated spot on the surface reaches boiling temperature, material removal starts due
the processes of vaporisation and melt expulsion. Laser enables drilling of a diamond die
in a few minutes as against 20 hours taken by conventional methods. There is no wastage
in the process and the saving in terms of the cost of diamond dust helps in recovering the
financial outlay on such a drilling system.

34
Laser light energy is primarily applied in effecting
microopenings in rubies and diamonds. Without heating the
entire machined unit, now possible to drill filament canals in
refractory materials. Laser drilling of holes in a diamond
takes 2 to 3 minute as against 2 to 3 days taken by
conventional drilling. A laser installation in Russia drills
holes with diameters and depths from 0.005 to 0.8 mm and
depths from 1 to 3 mm, respectively, in diamonds of any
size and shape.
The plus point about laser drilling is that it does not cause any
damage to the diamond or any other processed material. A
typical hole drilled in a ruby disc is shown in Fig: 5.1.

For laser drilling, usually pulsed carbon dioxide, Nd:YAG or alexandrite laser is used.
Special operations like drilling of holes with diameter less than 0.5 mm using
conventional techniques are difficult. However, the pulsed laser microdrilling is quite
successful for such operations, both for metals and non-metals. The Nd:YAG laser emits
at 1.06 µm and the alexandrite laser is tuned at 755 nm. For some metals, the alexandrite
laser consistently gives a cleaner entrance hole with more roundness and finer edges than
is obtained with Nd:YAG laser. The superior performance of alexandrite laser is due to its
shorter wavelength and continuous spiking of its output. The absorption of most materials
increases with shorter wavelengths, giving alexandrite laser an edge over the Nd:YAG or
laser in many material processing applications.

2.14 Laser Micromachining

In the recent years, lasers have also found applications in the field of microelectronics
where the laser beam interacts directly with circuit boards and semiconductor chips
containing memory and logic circuits. Such laser processing applications have made
possible due to development of lasers with increasing stability, high repetition rates,
wavelengths well into ultraviolet region, and short pulse durations. These features make it
possible to heat discrete micrometer-sized regions reliably and repeatedly to very high
temperatures. When applied to local regions of a silicon chip, laser heating can occur
without producing damage to neighbouring material or adjacent circuitry. Laser
machining is capable of forming tiny electronic circuit patterns directly on to ceramic
substrates in one step. The process makes use of a laser assisted by a computer so that it
is programmed to describe type of circuit pattern to be machined.

2.15 Laser Cutting

s, sapphire, and ferrite. In most cases, continuous cutting is carried out with assist gases
like oxygen, carbon dioxide, or air, which produces both mechanical and chemical action
intensifying the thermal effects. This gas-assisted cutting is cutting is the cutting of steels

35
Use of laser cutters in the garment industry, a new and very useful application of the
lasers, has been introduced recently in the developed countries. With the aid of
computers, lasers can cut clothing many times faster than the tailors using old techniques.
It is now possible to slice the through several layers of thick cloth accurately and in a
short time using a laser cutter. The laser system also consists of a computer, programmed
with cutting instructions and patterns for various to garments. The laser beam, focused on
the material cuts through the fabric, leaving impeccably he smooth edges.

2.16 Laser Hardening

The principle of laser hardening is the irradiation of material surface for a short time.
Heat is conducted into a metal causing quick heating of a thin layer. During the heating
period, a high temperature gradient is built up in the surface zone followed by a rapid
self- quenching by the cool sub-surface material. The complete hardening d cycle takes
about 1 to 2 s. The conventional surface hardening processes, such as flame hardening or
induction hardening, often cause a amount of distortion so that the work I becomes waste
or there are high additional costs.

Medium and high carbon plain steels more than 0.3 per cent carbon are generally well
suited to laser hardening. Their maximum hardness is a function of their carbon content.
mount of alloying elements, such as chromium manganese or molybdenum increases the
hardenability. The advantage of laser hardening of steels is the possible substitution for
expensive alloy steels. With the development of new techniques, lasers are now also
being used to harden several other industrial products.

Normally for hardening a track width few millimeters, an output of more than 1 kW from
the laser is considered desirable. Recent many laboratories engaged in laser application
and research work all over the world, multi watt lasers have been installed. For heat
treatment and hardening, usually a continuous wave beam from a carbon dioxide laser is
used. To avoid accidents, safety precautions like use of laser goggles are essential.

36
2.17 Metrology

With its high degree of coherence monochromaticity, laser is ideally suited in

metrologythe science and system of measurements for measuring lengths, velocities and
optical

characteristics of various media. An accurate method of measuring distances is in terms

wavelength of light. A conventional technique uses an instrument called interferometer
for optical measurements (surface flatness, parallelism of mirrors, variation of refractive
index, etc).

Using a helium-neon gas laser as the light source in the interferometer, the highest
accuracies are possible in the various optical measurements. In fact, the international
standard of length, i.e., one meter is calibrated with the help of a frequency-stabilised
laser. In the Apollo II mission, American astronomers aimed laser beam on the moon and
determined the distance of the moon from the earth to an accuracy within one fool This
type of refinement in optical measurements will enable scientists to measure precisely the
factors like lunar orbit motion, lunar radius, and fluctuations in the earth's rotation rate.
Ultimately, it will be possible to say definitely, whether the continents on the earth are
drifting and if so to what extent.With the help of a laser altimeter, the precise height of an
aircraft at a given time and also the rates of its ascent and descent can be determined
with high accuracy.

The ordinary altimeter depends on air-pressure changes for its readings and thus is not
dependable at low-flying levels. The radio altimeter (a radar which reflects radio
microwaves received from the ground) has limited accuracy for short distances. Laser
altimeter, working on the principle of laser range finder, sends short laser pulses towards
the ground from the aircraft and the reflected pulses are detected. Time taken by the laser
pulses to travel to ground and back is measured and expressed in terms of height. The
device has been used to measure heights up : 3000 m from an aircraft with an accuracy of
1 m Cloud altitude meter with a laser is being used to find the range of the cloud
accurately. It also works on the principle of a range finder. The light pulse from a laser is
sent upwards in the air and the time taken for the pulse to hit the cloud and its detection
after reflection, gives the distance of the cloud. The range has to be determined in both
clear and bad weather conditions like haze or fog. Since the cloud particles have size of
about a micron, the scattered intensity would be more for visible wavelengths. Hence,
ruby laser emitting powerful red pulses is highly suitable for this purpose. With this
system, it possible to determine the height of the clouds up to 10 km with an accuracy of
±5 m.
37
2.18 Laser for Surveying

A breakthrough in surveying has been achieved by teams to map about 5 per cent more
terrain in a given time while improving the accuracy to within 1 cm in 10 km.
optical axis, the beam guides the machines used for levelling the concrete facing of the
airfields, checking the verticality of the framework of tall buildings, sinking mines, and
cutting tunnels from two ends and joining them without tilt.

In Moscow, a laser centring device was used to control the vertical axis during the
construction of a TV tower with a precision of 6 mm. In the US, a hard rock boring machine
has cut a tunnel, 6.5 m in diameter and 2 1/4 km long, without deviating from its planned
course more than 1.58 cm in any direction. This feat was accomplished with the help of
the laser beam.

Laser direction finders are widely used in coal mines. In view of the high rate of
digging in coal mining, the biggest difficulty is to maintain accurately the given
direction, which is achieved using a highly directional laser beam.Similarly,
geodolite is used for the detection and measurement of the deformation of large
dams and bridges.

38
5.8 Optical Fibre Communication

The communication using light as signal carrier and optical fibres as a transmission
medium is termed optical fibre communication. Since the the first commercial installation
of a fibre optic system in 1977, the applications of optical fibre communication have
increased enormously. Today, every major long distance telecommunication company is
spending millions of dollars on optical fibre communication systems. In a optical fibre
communication system, voice, or data are converted into a coded pulse of light using a
suitable light source. This stream is carried by optical fibres to a regenerating or receiving
station. At the final receiving station, the light pulses are converted into electrical signals,
decoded, and then converted into the form of original information.

In future, fibre optics is going to be the choice for many communications applications.
The biggest advantage of a light wave system is its tremendous information carrying
capacity. There are already systems that can carry several thousand simultaneous
conversations over a optical fibres, thinner than human hair. In addition to this extremely
high capacity, the light guide cables are light weight, immune to electromagnetic interfer.

Optical fibres used in communication waveguides made of transparent dielectrics whose

function is to guide light over long distances. An optical fibre consists of an inner
cylinder of glass called the core, surrounded by a cylindrical shell of glass of lower
refractive index, called the cladding.

39
Optical fibres may be classified in terms of the refractive index profile of the core and
whether one mode (single mode fibre) or many modes (multimode fibre) are propagating
in the fibre. If the core, which is typically made of a high-silica-content glass, has a
uniform refractive index, it is called a step-index fibre. If the core has a non-uniform
refractive index that gradually decreases from the centre towards the core-clad interface,
the fibre is called a graded-index fibre. The cladding surrounding the core has a uniform
refractive index that is slightly lower than the refractive index of the core region. If the
core diameter is very much reduced so that only one ray can pass through the fibre, it is
called a monomode step- index fibre (or single mode fibre). Figure 5.2 shows a block
diagram of an optical fibre communication system.

The basic purpose of an electrical receiver is to detect the received light incident on it and
to convert it into an electrical signal containing the information impressed on the light at
the transmitter end. An optical receiver consists of a photodetector and an associated
amplifier along with necessary filtering and processing. The amplifier converts this
current into a usable signal without introducing noise to distort the signal. In the usual
fibre optic communication systems, the photodetector used is either a semiconductor pin
or avalanche photodiode (APD).

5.9 Applications of Optical Fibre Communications

Due to the unique advantages of the optical fibre communications, namely, the
tremendous information carrying capacity, freedom from electromagnetic interference,
light weight of fibres, longer distance between repeaters, and freedom from signal
leakage and crosstalk, this new technology is finding immense applications in the of
telecommunications. Already, the telecommunications market for optical fibres has
exploded in several developed countries, like USA, UK, France, Denmark, Germany,
Japan, etc. The need for greater circuit capacity coupled with the problem of congested
duct space led to the initial applications of optical fibre communication for the interoffice
trunk in the big cities. Today, the biggest market for optical fibre is the long distance
communication. Japan has already completed its long distance routes using single mode
fibres. In the US, thousands of kilometres of optical cables are being installed by giant
companies, like AT&T, GTE, BELL, etc. Submarine optical fibre cable across the Atlantic
Ocean are operational for the last few years.

40
A system with an AlGaAs laser for 850 nm wavelength and a graded-index multimode
fibre is applied to intra-city networks with bit rates of 32- 140 Mb/s and with
transmission spans shorter than 10 km. For distances more than 10 km, a system with in
GaAsP laser operating at 1 300 nm wavelength and with a graded-index multimode or
single mode fibre is preferred in inter-city networks with bit rates higher than 100 Mb/s.
When more telecommunication channels are required in a metropolis, the optical fibre
telecommunication system is quite effective because the special fibre cables which give
more bandwidth can easily replace the existing metal-wire cables in the duct Majority of
the present companies use single mode fibres that operate at 1300 nm wavelength with
future upgradability to 1500 nm where the attenuation loss will be the least. Already,
commercial systems have been installed with bit rates as high as 565 Mb/s which is
equivalent to 7680 two-way conversation over a pair of fibres. Since fibres have very
high capacity and can transmit voice, data and video, efforts are underway to install fibres
into individual houses, with universal information system. Systems are already in use that
provide continuing interactive service smoke and heat detectors to automatically alert fire
alarms, police alarms and medical alert alarms to summon aid. There is also a potential
for completely automating all the control needs of household.

Networks using optical fibres to transmit voice, video and data within a building or
within industrial complexes and university campuses have been offered by several
vendors. These systems are called local area networks and they cal improve
communication inside a high- use area, reduce the bulk of the copper cables, and
eliminate congestion in computer rooms.

Optical fibre communications are also( being used for industrial applications, such as
process control in nuclear, petrochemical, chemical and food industries and numerical
control in for internal links that require very high data rates of the order of gigabits per
second (Gb/s). Auxiliary equipment require lower data rates and hence can be hand and
error-free operation; because their transmission is unaffected by the

electromagnetic noise. They will be used in greater volume as inter- and intra-computer

41
Optical fibres are also very useful in Defence applications. Fibres can be used for data
links in aircraft with tremendous reduction in weight and increased information capacity.
Such aircraft include surveillance and attack aircraft and strategic air command bombers.
Similar applications exist for inter- and intra-ship communications, submarine mobile
command centres, ship-to-satellite communication links and all types of missile guidance
systems. All the above types of applications exist today, making the military applications
a large market for fibre optics communications.

Another interesting application is for sensors. In general, a sensor system consists of an

electronic control module, sensor head and fibre optic cable. The sensor head senses
pressure, temperature, velocity and reaction and converts it into a change in the optical
signal which is then analysed to measure the desired change by the electronic control
unit.

Lasers have great potential in TV and the cinema. Instead of microwaves as the carrier,
laser beam can be used for the transmission of television programmes through optical
fibre cables. Since the channel capacity is very high, many TV programmes can be
accommodated in a single laser beam.

5.10 Data Storage

The storage of higher density of data is possible by using optical techniques. The storage
medium is generally a thin film of metal whose optical properties change when it is
illuminated with a powerful write laser. The less powerful read laser reads the change in
optical property as the required information. Since laser beam can be focused on the spots
smaller than one micro diameter, it takes less than one square micro record one bit of
information, i.e., 100 million per square cm. Laser video and compact disc! examples of
such data storage media in the entertainment market. The magnetic data storage vices like
the present day video cassettes in market cannot have such high density data age.
However, the main drawback of optical storage is that it is not erasable; such eras optical
discs are expected to come into the market within a few years.

5.11 Holography

Another important application of laser beam is the production of true three-dimensional

pictures in space without the use of lens. The record of' this three-dimensional image of
the object on a film is called a to be recorded, so that sl1itably reflected from the object.
The refer. beam and the reflected beam are made to with each other to form an
interference patter the photographic plate.

42
To get a high quality hologram, radiation of in high coherence is required. Generally, the
helium-neon gas laser which gives highly coherent and Its I continuous output beam, is
used for this purpose. re Sometimes, high power pulses from a solid-state laser like ruby
laser, are also used. The exposure time, in the case of continuous gas lasers may be from
several seconds to a few minutes whereas a giant pulsed laser requires only a few
nanoseconds. The holograms are recorded on special le photographic plates with good
resolution. The plate is developed and fixed in the usual way.

There is a kind of magic about the hologram. With naked eye, it does not give any picture
of the object but only an exposed negative with grayish random patterns on the surface.
When it is positioned in its holder and viewed in a monochromatic light beam, such as
that produced by laser, the random patterns are transformed into le a sharp and detailed
three- dimensional image of b- the object. The image looks like a solid object hanging in
space in three dimensions; the viewer may change the angle of view by moving his head
from side to side or up and down.

Holography is being used for non-destructive testing, holographic information storage,

display devices and pattern matching procedures for 'a such tasks as credit card and
identity card verification. Holographic methods can also be used for is secret
communication of information by recording e the holograms of secret documents, maps
and objects, and restructuring the images only at the receiver end. Interference
holography can be used to measure accurately how structures deform under the effect of
mechanical stress or thermal gradient.

43
Standard holograms may be used in industrial production processes to check high
precision components with regard to their shape dimensional accuracy. First, a hologram
is from a masterpiece according to the method shown in Fig. 5.4. The reconstructed
image ( hologram serves as a kind of reference. The to be inspected (the deviations of
which are checked), is placed at the spot where the master was earlier placed. If the
specimen is now exposed in the same way as the master and watched through the
developed hologram, small deviations of shape with reference to the original are
indicated by interference lines on the specimen. a study of the sensitivity of the
interference method (any deformations of the laser light result in an Interference line),
even the mistakes within the component ( e.g. cracks, cavities, etc) are indicated in the
interference link patterns.

Some day, holographic technique may even be used for target recognition from air to
ground and we may eventually have holographic movies and television, giving better
appreciation of the objects projected to the viewers.

5.12 Medical Applications of Lasers

Lasers are extensively used in medicine and surgery. The first practical application was in
eye surgery, where laser was used to weld detached retina and photocoagulate the blood
vessels that grow into the region in front of the retina, thereby blocking vision.
The laser beam easily passes through transparent portions of the eye, including Cornea
and lens to the region of its intended use where its energy is absorbed for treatment.
Retina is a sensitive membrane inside the eyeball. Its detachment from the surrounding
choroid coat initiates due to a hole in the retina caused by an injury or degenerative
changes during the old age. This makes the thick fluid vitreous humour seep and fill itself
between the retina and chord oat. The pressure between the retina and choroid coating
damages the retina which Soon gets detached from the optic nerve at the back of the to
cause blindness.

Before the invention of laser, this delicate operation was done by irradiation of the eye
with a xenon arc lamp or even by focusing the sunlight on to the choroid coat. This
method involved exposure time to concentrate sufficient he the site of the detached retina.
The process cumbersome, painful and relatively slow. Be the patient had to be
anaesthesised to prevail eye from moving. Using a high energy pulsed laser, like
Nd:YAG, the intense laser light focused as a tiny spot at the detached retina 'welding' it to
the underlying choroid coat of the also be used to burn out small tumours on the surface
of the eye and also those in the vessels of the eye. It is being used to treat coma, cataract,

44
The laser cane which is a boon for blind persoi1S operates on the principle of a radar.
Two lasers within the cane provide pulses of infrared light which are reflected from
points, a short distance in front of the cane. Each reflected beam returns to a photocell
inside the cane. The two photocells activate pins in the handle. When the path is smooth,
the two pins vibrate steadily. Any hole or other obstacle scatters the light from at- least
one of the lasers and stops the vibrations, thus warning the user. The device operates on
four small batteries which last up to ten hours. It allows a blind person to scan the area
ahead of him and have an idea of the object's shape, distance and dimensions by
variations in pitch and intensity of the tone it emits

Lasers are increasingly being used for the treatment of many different types of cancer. A
laser is less damaging than x-ray therapy and surgery; and in many cases, it is quite
effective. The use of lasers to remove certain forms of cancerous growth in the body has
heralded an era of knifeless and bloodless surgery. It is very effective in curing the
diseases of gynaecology, ear, nose, throat, tongue, palate, and cheeks. It is curative in
most early cancers, and in late cancers, it is useful in reducing the tumours to facilitate
surgery.

Photodynamic therapy (POT), a new exciting form of cancer treatment, combines laser
with light-sensitive dye, hematoporphyrin derivative (HPD). This substance, derived
from the cow's blood, travels throughout the body of the patient and settles in the
malignant tissues. A red light from argon pumped dye laser, focused on the area activates
HPD, and the energized substance releases a highly reactive chemical that destroys the
cancer cells. Reports indicate that POT is 80 to 90 per cent successful in causing total or
neartotal regression of tumours, even after all other forms of therapy have failed. It is
highly selective for a diseased tissue, leaving healthy cells relatively untouched.

At some medical centres in the US,searchers have used laser to treat colonic and other
types of gastrointestinal cancer. Using endoscope, the laser energy is used to destroy
neoplastic tissue while preserving bowel wall integrity. In some cases, rectal polyps were
removed using the CW argon laser, delivered with a power of 4-5 W.

45
With the development of optical fibres lasers are being used for heart surgery. A common
problem with the arteries is the build up of plaque on their interior walls. The plaque,
consisting fatty material, calcium, etc, blocks the coronary. arteries reducing the blood
flow through the This results in Angina pectoris, a condition that afflicts millions of
people worldwide. If the coronary artery is partially blocked, the situation can sometimes
be improved by using a method called angioplasty. When substantial blockage of the
coronary artery is observed, a laser beam se through the optical fibre could be used to
vapourise the plaque, opening a clear channel for smooth flow of blood. This method is
called laser angioplasty or vascular recanalisation. Usually argon-ion, Nd:YAG, and
carbon dioxide lasers al used for this purpose.

Another important use of the fibre-optic laser catheter is in the treatment of bleeding
ulcers. The laser light can photocoagulate blood, thereby causing the cession of bleeding.
For this purpose among the three important lasers(carbon dioxide, Nd:YAG and
argonion), the Nd:YAG laser is preferred because it penetrates deep into the tissue and its
effects are not localised at the surface. Using a laser endoscope, small tumours in the
urinary bladder are destroyed. Similarly, Nd:YAG and dye lasers are also used to rapidly
heat and shatter urinary stones in the kidney

Laser can also be used for dental treatment Laser beam is useful for charring tooth decay
through a painless process called laser glazing. The beam from a high repetition pulsed
laser can be focused on dark decayed areas of teeth cavities to destroy the infection in the
affected areas in a fraction of a second.
3. Laser Applications III :Miscellaneous

3.1 Laser Printing

For the last few years, there has been tremendous increase in the use of computers as an
aid to the management, processing and dissemination of information. The use of
computers in generating bank statements, insurance, telephone and electricity bills as well
as publicity brochures advertising mass-produced goods are typical examples of this
development. The peripheral device required by the computer for all these applications is
the printer. Today, use of computers in large data processing installations places very
high demand on printers as regards its speed, character flexibility, and print quality. The
conventional impact printers can no longer meet these demands because of their limited
speed and character flexibility. In the new generation printers, printing method is based
on the principle of electrophotography. Since the light source in such printers is a laser,
these devices are called laser printers.

47
Figure 6.1 is a schematic diagram of a laser printer. A photoconductor drum (1) at the
centre rotates at a constant angular speed. Its surface is treated with a photoconductive
coating material like hydrogenated amorphous silicon. In the dark, this photoconductor
has a very high electrical resistance which drops when the coating is exposed to light.
The surface of the photoconductor drum is electrically charged by means of the charge
corotron (2) and the charged layer is then rotated past the write exposure station (3). Only
those locations on the drum surface at which the Information to be printed is to appear are
exposed. Two exposure facilities transmitting current computer data and the information
to be repeated on each print page (company letterhead, tables, bill forms) are available ( 4
). As a result of exposure, the surface charge flows to ground inside the drum leaving a
latent electrostatic charge pattern. The developer station (5) contains an electrostatically
charged toner. The paper transport (6) moves the paper up to the drum and to the transfer
station (7). The paper and toner charges are of opposite polarity so that the toner is
attracted by the paper and adheres to it. The photoconducting drum is discharged in the
discharge station
(9) and the process is repeated.

High-performance laser printers offer three important advantages:

High printing speed, about 10,000 lines per minute at six lines per inch, which
(i) . makes it possible to print over four million characters in one minute.
Very high degree of flexibility as regards character generation. Today, the laser
printers have character sets of several hundred different characters. Since the print
(ii)
characters are stored electronically, the only consideration limiting the number of
characters available in the printer. is the cost I of the necessary memory space.
(iii) Excellent print quality.

3.2 Seismography

In its seismographic application, i.e., detection of earthquakes and underground nuclear

blasts, the instruments using lasers are ten times more accurate than the conventional
devices. This laser application is based on the principle of Doppler shift in the frequency
of the light scattered from a moving substance. The scattered beam is mixed with the part
of the. incident beam in a detector and the beat frequency is determined, which gives the
measure of the movement of the earth's crust.

3.3 High-Speed Photography

The intense laser light also finds application in high-speed photography for recording
extremely fast or transient phenomena like the bullet shot by a gun, armour penetration

48
from Q-switched lasers, capable of exposing up to 9,000 frames per second. Ultrashort
pulses can be used to study ultrafast phenomena and processes, such as recombination of
electron-hole pairs or excitons in semiconductors.

3.4 Scientific Research

Lasers have opened new fields of investigation in science and technology. It has given
physics a versatile tool for the study of interaction of light and matter. The powerful
beam of laser has become an important tool for spectroscopic analysis. A laser system,
known as microprobe, is used for exciting emission from solid samples for
spectrographic analysis.

In 1928, Prof. CV Raman discovered a new phenomenon, known as Raman Effect. by

which molecular structures of different substances can be investigated by passing
monochromatic light through them. He found that when light passes through a transparent
substance, it is scattered and emerges with a change of frequency caused due to the
vibration of molecules in the substance. This produces additional lines (known as Raman
lines) in the scattered light spectrum. The discovery of laser is a great boon for recording
the Raman spectra. The use of lasers has enabled recording of Raman lines within
seconds, which otherwise would require long exposure times of or few hours using
ordinary light sources. The analysis of Raman lines gives the fundamental properties of
the substances.

Similarly, lasers can also be used for analysing liquids. A laser beam, when passed
through a liquid, gives several colours (wavelengths) and the process is called
fluorescence. The study of the fluorescence spectra thus obtained gives the properties of
the liquids.

Lasers offer attractive possibilities in terms of the exploration of molecular structure and
determination of nature of chemical reactions. A laser beam can initiate and hasten a
chemical reaction. Since different reactions require different wavelengths of light, a
'tunable' laser (i.e., a source whose wavelength can be altered as in radio tuning) is of
immense help to a chemist. Tunable lasers, particularly dye lasers, now cover the entire
visible spectrum and have revolutionised optical spectroscopy. In photochemistry, lasers
with short duration pulses are highly useful for inducing and monitoring ultrafast
chemical reactions more efficiently than by any conventional method.

Laser also finds application in biological research. Using laser techniques, biological
studies have been carried out in enzymes, proteins, cellular components and isolated
cells, microorganisms, tissue culture, isolated physiological systems individual organs,
etc. Using a ruby laser coupled with a microscope, single cells have been irradiated with
laser beams focused on to a spot of the order of one micron to destroy individual chro

It is also possible to produce laser beams as narrow as the diameter of a protein molecule
and use it to alter genetic properties of living organisms.

49
3.5 Environmental Studies

The constituent gases and vapours in the atmosphere can be detected and measured with
lasers by means of at least three selective mechanisms. These are: ( 1) selective
absorption of laser light which spectrally matches the natural absorption characteristics of
the molecule, (2) resonance or fluorescence scattering of laser light, and (3) Raman
scattering.

The absorption lines of water vapour in the atmosphere are very close to the emission
wavelength of ruby lasers. By tuning the wavelength of a ruby lidar, one can observe the
change in backscatter caused by absorption within the water vapour lines. With the
availability of tunable dye lasers, it is easier to take advantage of resonance scattering
which helps to identify the constituents of the atmosphere. In recent years, the laser
techniques have been well established for the purpose of environmental monitoring,
cloud height detection, and urban pollution studies.

3.6 Nuclear Fusion

Thermonuclear fusion is the process by which huge energy is produced in the sun and
.stars. It is the process by which nuclei of light elements such as deuterium (an isotope of
hydrogen) are fused (or joined) together to produce heavier elements like helium. In this
reaction, a large quantity of energy and neutrons are released.

For thermonuclear fusion to take place, a temperature of about one million degrees
centigrade is required. Today, this is achieved by the implosion of the atoms of the
material by a focused high energy laser beam. Thermonuclear re. action has several
advantages over the fission process. Firstly, the immense energy comes from a very small
quantity of material. Secondly, the supply of fusion fuel is virtually inexhaustible as
deuterium can be extracted cheaply from the world's oceans. Thirdly, there is no problem
of atmospheric pollution. It will be simpler and easier to make a hydrogen bomb which
will be 'clean', i.e.,its explosion will be free from the lingering effects of radioactive
fallout.

cause turbulent hot air to rise. The laser beam, normally steady, is refracted by the
temperature gradients in the hot gases and is displaced from its usual position on a
photocell. The deflection can be made to trigger an alarm. Results have indicated that the
laser beam system is at least as fast as the most sensitive fire detection systems in use

6.8 Intrusion Alarm

A gallium arsenide diode laser can be used to set up an invisible fence to protect an area.
An infrared laser beam (in combination with an optical detector) can seal a path, an area
or
50
a volume against infiltrators. When the invisible beam is interrupted by an intruder trying
to approach the protected area, it sets off a remote alarm. The laser alarm has many
advantages over the conventional electric alarm. The infrared beam, being invisible,
cannot be spotted by the intruder. The narrowness of the beam minimised false alarms by
the passage of birds, small animals and objects floating in the air.

4. Status of Laser Development in India

The research and development work in the field of lasers started in our country 28 years
back on a very small scale at a few research laboratories of the Defence Research &
Development Organisation, Bhabha Atomic Research Centre, National Physical
Laboratory, IIT, Kanpur, and IISc, Bangalore. Later, a number of research laboratories
and teaching institutions also entered into this area. A Study Group on Lasers, constituted
in 1971 by .DRDO, and INSA Laser Committee constituted under the Chairmanship of
Prof. P Venkateswarlu in 1976 (the author was a member of the two committees) made
detailed studies to assess the status of R&D work on laser at both international and
national levels and gave suitable recommendations for development of lasers and laser
systems in the country. In 1988, Dr DD Bhawalkar, Director, Centre for Advanced
Technology (CAT), Indore, gave a status report on lasers to the Science Advisory Council
to the Prime Minister. Very briefly the current status of the laser work in the country is
outlined below:

4.1 Ruby, Nd:YAG and Nd:Glass Lasers

Laser rods of ruby, Nd:glass, flash lamps and hard coated laser mirrors, have been
developed indigenously at the Defence Science Centre (DSC), Delhi, and the solid sate
lasers giving peak power output of a few megawatts have been developed for Defence
applications. BARC has also developed these lasers with mainly imported components,
Laser range finders with Nd:YAG or Nd:glass as the active element have been developed
at Instruments Research Development Establishment(IRDE), Dehradun and DSC. CAT,
is developing a high power Nd:glass laser for atomic energy application,

4.2 Helium-Neon Laser

Helium-Neon lasers of low power output (2- 5 mW) with lifetimes of a few thousand
hours have been developed at IISc, NPL, and Bharat Electronics Ltd., Bangalore. The
technology has been transferred by NPL to M/s Laser Instruments, New Delhi and by
BARC, Bombay

51
to ECIL, Hyderabad. they started production of these lasers commercially about 20 years
back but stopped production since their is far from satisfactory. BEL also made an
attempt about 10 years back and stopped production due to lack of sufficient technology

4.3 Carbon Dioxide Laser

Carbon dioxide lasers giving an output power in the range 10-100 W have been
developed at BARC IIT, Kanpur, IRDE and DSC, Central Electronics Ltd. (CEL) and
Jyoti Ltd. have started commercial production of these lasers around 1975 but have
stopped production by 1982. CAT has developed transverse carbon dioxide laser with 3.5
kW power.

4.4 Semiconductor Laser

BARC and Solid State Physics Laboratory (SPL), Delhi have developed low power
gallium-arsenide lasers with a view to use them for applications in communication and
ranging. BARC demonstrated communication over 20 Km distance using laser. Further
work is necessary to develop these lasers with heterostructures and to improve their
efficiency.

4.5 Materials

Basic laser materials like ruby, Nd:phosphate glass and lithium niobate are being
developed at DSC for Defence applications, Central Glass and Ceramics Research
Institute, Calcutta(CGCRI), has also developed good quality Nd:silicate glass for
commercial applications. The development of gallium-arsenide and Nd:YAG crystals is
under process at SPL. Several establishments and institutes like DSC, IRDE, IISc, NPL,
BARC, IIT, Kanpur and BEL have established optical workshops including coating
facilities to fabricate laser components. Good experience has been gained to fabricate
laser rods and hard coated laser morrors at DSC

4.6 Fibre-Optic Communication

In 1980, a panel on Optical Fibre Communication System constituted by the Electronics

Commission recommended the introduction of optical fibre communication in India.
With this in view, CGCRI took up an R&D project on indigenous development of optical

52
setting up of R&D and manufacturing facilities of optical fibres and cables at HCL through
collaborative arrangement. It was decided to manufacture at HCL the multimode graded
index fibre with' 3 to 5 db/km loss and bandwidth up to 100 MHz. Similarly, the
production of optical fibre has been started at OPTEL, Bhopal with foreign collaboration.
In 1983, a

Committee on Optical Fibres and Cables (COFC) was constituted by the Ministry of
Communication to finalise the technical specifications for optical fibres and cables required
not only for communications, but also for Defence and other sectors.

The Department of Communications has Successfully installed the optical fibre cable and
an 8 Mb system to provide junctions between two exchanges in the Pune Telephone
system. TRC has taken up a design of an indigenous 34 Mb .system to be installed
between Thana and Powai in the Bombay Telephone system. Efforts are on1e way to
introduce optical fibre communication several trunk routes in the country. Facilities for 93
characterisation of optical fibres have been set up at HCL and IIT, Delhi.

53
4.7 Need to Develop Laser Technology in India

There are large gaps in the development of laser technology and its production between
our country and other developed countries. Efforts in this area have been so limited in our
country that they are not even equal to the efforts made at one major institution in the
USA. Not a single reliable laser system is commercially available in the country. Though
some institutions in our country have fabricated some experimental lasers on a laboratory
scale, reliable operation of these lasers has still been a problem. As an outcome of status
report of SAC to PM, a National laser Programme has been started recently.

Advantages of lasers for various applications in our country are well known and laser
research has been recognised as one of the frontier areas to be developed in the 8th Five
Year Plan. It is high time for our country to intensify the R&D efforts in the identified
areas with time bound pro- Grammies and start the production of lasers for mass
applications.

54