“SSS YAESU YESTERSTANOARD C05 LTO. san ieareeetaetes FM TRANSCEIVER o200 Waker Sweet, Cypress, CA 90620, US.A. YAESU UKLTD. Uni 12, Sun Valey Business Park. Winnall Close FT-1 900R Winchester, Hampshire, $023 OL8, UK VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 199-141 Hoi Bun Road, ‘Kwun Tong, Kowloon, Hong Kong Technical Supplement VERTEX STANDARD (AUSTRALIA) PTY., LTD. NarenoySuppens Park ni Nermany Road (©2009 VERTEXSTANDARDCO, LTD. EHODSNDIA Noting i HBB Vises, Alsat Introduction This manual provides technical information necessary for servicing the FT-1900R FM Transceiver. Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non- qualified persons to service this equipment may result in permanent damage not covered by the warranty, and may be illegal in some countries. Two PCB layout diagrams are provided for each double-sided circuit board in the Transceiver. Each side of is referred to by the type of the majority of components installed on that side (“leaded” or “chip-only”). In ‘most cases one side has only chip components, and the other has either a mixture of both chip and leaded components (trimmers, coils, electrolytic capacitors, ICs, etc.), or leaded components only. While we believe the technical information in this manual to be correct, VERTEX STANDARD assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated. Contents Specifications svomine2 Board Unit (Schematics, Layouts & Parts) Exploded View & Miscellaneous Parts w.u3 MAIN Unit Circuit Diagram . MAIN Unit Parts Layout Block Diagram MAIN Unit Parts List. Connection Diagram NTL Unit Cireuit Diagram NTL Parts Layout Cireuit Deseription eariree re Alignment... ———Specifications General Frequency Range: ‘Tx 144 - 146 MHz or 144 - 148 MHz Rx 144 - 146 MHz or 136 - 174 MHz Channel Step: 5/10/12.5/15/20/25/50/100 kHz Standard Repeater Shift #600 KHz. Frequency Stability: Better than +10 ppm [-4 °F to +140 °F (-20 °C to +60°C)] Modes of Emission: F2D/F3E Antenna Impedance: 50 Ohms, unbalanced Supply voltage: 13.8 V DC 415%, negative ground Current Consumption (typical): Rx: less than 0.7 A, less than 0.3 A (squelched) Tx: 10 A (55 W) /7 A (25 W) /5.A (10 W) /4 A (5 W) Operating Temperature Range: —4° F to +140° F (-20° C to +60° C) Case Size (WxHxD): 55” x 1.6" x57” (140 x 40x 146 mm) (w/o knobs) Weight (Approx.): 26 Ib (1.2kg) Transmitter Output Power: 55 W/25 W/10 W/5 W Modulation Type Variable Reactance Maximum Deviation: 45 KHz/42.5 kHz Spurious Radiation: Better than ~60 dB Microphone Impedance: 2000 Ohms. Receiver Circuit Type: Double Conversion Superheterodyne Its: 21.7 MHz & 450 KHz Sensitivity (for 124B SINAD): Better than 0.2 uV Selectivity (-6/-604B): 12 kHz/28 kHz IF Rejection: Better than 70 dB Image Rejection: Better than 70 dB Maximum AF Output: 3 W into 4 Ohms @10 % THD Specifications subject to change without notice or obligation. Specifications guaranteed only within Amateur band. Frequency ranges and functions will vary according to transceiver version; check with your dealer.Exploded View & Miscellaneous Parts opetz2001 CASE ASSY ‘WS NET: Sa002087 4090178, ‘SPEAKER ——— 52002118 2 pes Tez06436 2 WIRE ASSY eon ‘s8002063 CAP-SP [AAASSXO0% [MICROPHONE (MH-464) . freaot715 [OC CABLE (FT-1900R) To207s82 1094220 Fr0022815 | DC CABLE (FT- 19006) WIRE ASSY RAGOHTSI7Mt [00000151 [SPARE FUSE (15 A: FT-TO00R) [0000075 | SPARE FUSE (15 A'FT-1900E) ID6000055 | BRACKET (WMB-36) [cea2s7000 [SCREW SET 'uoss10002 [SEMS SCREW. ‘ASMSXION | 4 [zat 12002 [TAPTITE SCREW __MaXt2Ni_ [4 1U24308002 [TAPTITE SCREW NGXBNI [17 cea {U36206007 |TAPTITE SCREW MZ.6x65__|_9 151320007 |HEXA SOCKET BOLT_MSx208 | 3 Non-designated parts are available only as part of a designated assembly. 79207248, eo WIRE ASSY. Ye cNTLUNT Pioo72 RA0754500 CONNECTOR RA1105200 Rag753400 RUBBER KNOB. RAI118000 (x2 pes) KNOB (VOLISGL). CHASSIS 'RAO754400 GROUND PLATE, RA07S4300 REFLECTOR ‘RA0754600 DIFFUSER RA1105100 FRONTPANEL 'RA1118100 ENCODER KNOBNoteivadoiq 10018oe [LINA-NOT LEO LINQ—TLNO LINQ-NIvW Ge psSviq woys0uu03Receive Signal Path Incoming RF signal is from the antenna jack is de- livered to the Main Unit and passed through the low- pass filter network consisting capacitors C1213, C1236, C1239, & C1241 and coils L1017, L1018, & L1019, antenna switching diode D1020 and D1028 (both RLS135), and varactor-tuned band-pass filter consisting of capacitors C1248, C1249, C1250, C1251, C1252, & C1268, coils L1020, L1021, & L1024, and diodes D1024 and D1025 (both HVC350B), before delivery to the RF amplifier Q1045 (38K296ZQ). The amplified RF signal is passed through the another varactor-tuned band-pass filter consisting of capac- itors C1198, 1199, 1200, & 1218, coils L1012 and L1015, and diodes D1017 and D1021 (both HVC350B), then applied to the Ist mixer Q1037 (38K296ZQ) along with the first local signal from the PLL circuit. ‘The first local signal is generated between 114.3 MHz and 152.3 MHz by the VCO, which consists of Q1009 (28€5231) and varactor diode D1002 (HVC350B) according to the receiving frequency. IF and Audio Circuits ‘The 21.7 MHz first IF signal is applied to the mono- lithic crystal filters XF1001 and XF1002 which strip away unwanted mixer products, and the IF signal is applied to the first IF amplifier Q1032 (28C4400), ‘The amplified first IF signal is then delivered to the FMIF subsystem IC Q1028 (NJM2591V), which con- tains the second mixer, limiter amplifier, noise am- plifier, and FM detector. The second local signal is generated by 21.25 MHz crystal X1001, produces the 450 kHz second IF sig- nal when mixed with first IF signal within Q1028 (NUM2591V). ‘The 450 kHz second IF signal is applied to the ce- Iter CF1001 (for Narrow FM) or CF1002 (for Wide FM) which strip away unwanted mixer prod- ucts to the ceramic discriminator CD1001 which re- moves any amplitude variations in the 450 kHz IF signal before detection of speech. The detected audio from the Q1028 (NJM2591V) passes through the de-emphasis circuit consisting of resistors R1082 & R1113, and capacitors C1120 & C1122, to the audio mute gate Q1034 (28J364) rami Circuit Description ‘The audio signal passes through a band-pass filter consisting of Q1046 and Q1047 (both 25C4154), and the audio mute gate Q1039 (284347), to the audio VR which adjusts the audio sensitivity to compen- sate for audio level variations. The adjusted audio signal is delivered to the audio amplifier Q1035 (LA4425A) which provides up to 3 Watts, to the ex- ternal speaker jack or a 4-Ohm loudspeaker. Squelch Control When no carrier received, the noise signal from 21028 (NJM2591V) is amplified by Q1051 (28C4617), and is detected by D1011 and D1013 (both DA221). The resulting DC voltage passes through the SQL knob to main CPU Q2002 (HD64F2266TF13). While no carrier is received, main CPU Q2002 (HD64F2266TF13) control Q1048 (CD4094BPWR), thus, audio mute gate Q1034 (284364) and Q1039 (28J347) turns “OFF” to dis- able the audio output from the speaker. Transmit Signal Path ‘The speech signal from the microphone is amplified by Q1049 (LA2902PWR). The amplified speech sig- nal is subjected to the low-pass filter network Q1049 (LA2902PWR) to deviation controlled by Q1043 (M62364FP). ‘The adjusted speech signal from Q1043 (M62364FP) is delivered to VCO Q1009 (28C5231) which fre- quency modulates the transmitting VCO made up of D104 (HSC277), The modulated transmit signal passes through buff- er amplifier Q1010 and Q1023 (both 25C5374). The transmit signal applied to the drive amplifier 21026 (28€5226), then finally amplified by power amplifier module Q1030 (RAGOH1317M) up to 50 Watts. The APC circuit controls the Q1030 (RA6OH1317M) power amplifier’s gain ‘The 50 Watts RF signal passes through low-pass fil- ter network consisting of Capacitors C1210 and C1211 and coil L1013, antenna switch D1018 and 1019 (both XB15A709), and another low-pass fil- ter network consisting capacitors C1213, C1236, €1239, & C1241 and coils L1017, L1018, & L1019, and then deliver to the ANT jack.Circuit Description TX APC Circuit A portion of the power amplifier module output is rectified by D1022 (18$321), then delivered to APC (21038 (LM2904PWR), as a DC voltage which is pro- portional to the output level of the power amplifier module. ‘The APC Q1038 (LM2904PWR) is compared the rec- tified DC voltage from the power amplifier module and the reference voltage from the main CPU Q2002 (HD64F2266TF13), to produce a control voltage, which regulates supply voltage to the power ampli- fier module Q1030 (RA60H1317M), so as to main- tain stable output power under varying antenna loading condition. PLL A portion of the output from the VCO Q1009 (28C5231) passes through the buffer amplifier Q1010 and Q1017 (both 28C5374), then delivered to the programmable divider section of the PLL IC 1011 (MB15A01PFV1), which divided according to the frequency dividing data that is associated with the setting frequency input from the main CPU (22002 (HD64F2266TF13). It is then sent to the phase comparator section of the PLL IC Q1011 (MB15A01PFV1), ‘The 21.25 MHz frequency of the reference oscillator circuit made up of X1001 is divided by the reference frequency divider section of Q1011 (MB15A01PFV1) into 4250 or 3400 parts to become 5 KHz or 6.25 kHz comparative reference frequencies, which are uti- lized by the phase comparator section of Q1011 (MB15A01PFV1), The phase comparator section of Q1011 (MB15A01PFV1) compares the phase between the frequency-divided oscillation frequency of the VCO circuit and comparative frequency and its output is a pulse corresponding to the phase difference. This pulse is integrated by the charge pump and loop fil- ter into a control voltage (VCV) to control the oscil- lation frequency of the VCO Q1009 (28C5231),Introduction The FT-1900R is carefully aligned at the factory for the specified performance across the amateur band. Realignment should therefore not be necessary ex- cept in the event of a component failure. Only an authorized Vertex Standard representative should perform all component replacement and service, or the warranty policy may be void. ‘The following procedures cover the adjustments that are not normally required once the transceiver has left the factory. However, if damage occurs and some parts subsequently are replaced, realignment may be required. Ifa sudden problem occurs during nor- ‘mal operation, it is likely due to component failure; realignment should not be done until after the faulty ‘component has been replaced. We recommend that servicing be performed only by authorized Vertex Standard service technicians who are experienced with the circuitry and fully equipped for repair and alignment. If a fault is sus- pected, contact the dealer from whom the transceiver was purchased for instructions regarding repair. Authorized Vertex Standard service technicians re- align all circuits and make complete performance checks to ensure compliance with factory specifica- tions after replacing any faulty components. ‘Those who do undertake any of the following align- ments are cautioned to proceed at their own risk. Problems caused by unauthorized attempts at re- alignment are not covered by the warranty policy. Also, Vertex Standard reserves the right to change circuits and alignment procedures in the interest of improved performance, without notifying owners. Under no circumstances should any alignment be attempted unless the normal function and operation of the transceiver are clearly understood, the cause of the malfunction has been clearly pinpointed and any faulty components replaced, and realignment determined to be absolutely necessary. Alignment Required Test Equipment The following test equipment (and familiarity with its use) is necessary for complete realignment. Cor- rection of problems caused by misalignment result- ing from use of improper test equipment is not cov- ered under the warranty policy. While most steps do not require all of the equipment listed, the inter- actions of some adjustments may require that more complex adjustments be performed afterwards. Do not attempt to perform only a single step unless it is clearly isolated electrically from all other steps. Have all test equipment ready before beginning and, follow all of the steps in a section in the order pre~ sented. 7 RF Signal Generator with calibrated output level at 200 MHz 1 Deviation Meter (linear detector) 7 In-line Wattmeter with 5% accuracy at 200 MHz 1 50-Ohm 50-W RF Dummy Load 1 8-Ohm AF Dummy Load OF Regulated DC Power Supply adjustable from 6 to 15 VDC, 10A GF Frequency Counter: 0.2-ppm accuracy at 200 MHz © AF Signal Generator AC Voltmeter DC Voltmeter: high impedance VHF Sampling Coupler OSINAD MeterAlignment Alignment Preparation & Precautions A.50-Ohm RF load and in-line wattmeter must be connected to the antenna jack in all procedures that call for transmission; alignment is not possible with an antenna, After completing one step, read the next step to see if the same test equipment is required. If not, remove the test equipment (except dummy load and wattmeter, if connected) before proceeding. Correct alignment requires that the ambient tem- perature be the same as that of the transceiver and test equipment, and that this temperature be held constant between 68 °F ~ 86 °F (20°C ~ 30°C). When the transceiver is brought into the shop from hot or cold air, it should be allowed some time to come to room temperature before alignment, Whenever pos- sible, alignments should be made with oscillator shields and circuit boards firmly affixed in place. Also, the test equipment must be thoroughly warmed up before beginning, Note: Signal levels in dB referred to in the alignment procedure are based on OdBu = O.5pV. Test Setup Set up the test equipment as shown below for trans- ceiver alignment. Entering the Alignment Mode Alignment of the FT-1900R is performed using a front panel software-based procedure. To perform alignment of the transceiver, it must first be placed in the “Alignment Mode,” in which the adjustments will be made and then stored into memory. To center the Alignment mode: 1. Press and hold in the [MHz(SET)] key while turning the radio on. 2. Press and hold in the [PWR(®)] switch for 1/2 sec- ond to turn the radio off. 3. To enter the Alignment mode, press and hold in the [REV(DW)] and [D/MR(MW)] keys while turning the radio on. Once the radio is on, release these two key. The transceiver is now in the “Alignment Mode.” 10 PLL Reference Frequency OF Rotate the DIAL knob to set the alignment pa- rameter to “BO201 rf.” 7 Press the [D/MR(MW)] key to enable adjustment of the “PLL Reference Frequency.” 7 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the counter fre- quency reading is 148.000 MHz (#100 Hz). 17 Press the [D/MR(MW)] key. RF Front-end Tuning i Inject a 145.100 MHz signal at a level of -10 dB (with 1 kHz modulation @23.5 kHz deviation) from the RF signal generator. OF Rotate the DIAL knob to set the alignment pa- rameter to “80111 tn.” 7 Press the [D/MR(MW)] key to enable adjustment of the “RF Front-end Tuning.” GF Adjust the DIAL knob so that the maximum SINAD. 7 Press the [D/MR(MW)] key. Squelch Threshold Level Gi Inject a 145.100 MHz signal at a level of -14 dByt (with 1 kHz modulation @33.5 kHz deviation) from the RF signal generator. GI Rotate the SQL knob to the 10-0'cloc! position. Gi Rotate the DIAL knob to set the alignment pa- rameter to “BO111 tL.” 7 Press the [DIMR(MW)] key to enable adjustment of the “Squelch Threshold Level.” 1 Press the [DIMR(MW)] key three times. Gi Press the [DIMR(MW)] key. Dury Load ‘Signal Generator [ Feaweney ‘Test Eourpment SenS-meter Level (S-1) 1 Inject a 145.100 MHz signal at a level of -5 dBu (with 1 kHz modulation @:3.5 kHz deviation) from the RF signal generator. OF Rotate the DIAL knob to set the alignment pa- rameter to “B0111 81.” 1 Press the [D/MR(MW)] key to enable adjustment of the “S-meter Level (S-1).” 1 Press the [D/MR(MW)] key three times, 7 Press the [D/MR(MW)] key. S-meter Level (S-9) 1 Inject a 145.100 MHz signal at a level of +20 dBu (with 1 kHz modulation @#3.5 kHz deviation) from the RF signal generator. 17 Rotate the DIAL knob to set the alignment pa- rameter to “B0111 89.” 7 Press the [D/MR(MW)] key to enable adjustment of the "S-meter Level (5-9).” G1 Press the [D/MR(MW)] key three times, 17 Press the [D/MR(MW)] key. ‘TX Power (High) 0 Rotate the DIAL knob to set the alignment pa- rameter to “BO101 HP.” G1 Press the [DIMR(MW)] key to enable adjustment of the “TX Power (High).” 07 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the RF Power Meter reading is 50 W (#2.0W). 07 Press the [D/MR(MW)] key. TX Power (Low 3) 0 Rotate the DIAL knob to set the alignment pa- rameter to “BO101 L3.” 07 Press the [D/MR(MW)] key to enable adjustment of the “TX Power (Low 3).” 7 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the RF Power Meter reading is 25 W (#1.5 W). 7 Press the [D/MR(MW)] key. Alignment TX Power (Low 2) 1 Rotate the DIAL knob to set the alignment pa- rameter to “80101 L2.” 7 Press the [D/MR(MW)] key to enable adjustment of the “TX Power (Low 2).” Gi Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the RF Power Meter reading is 10 W (+1.0 W). 17 Press the [D/MR(MW)] key. TX Power (Low 1) Gi Rotate the DIAL knob to set the alignment pa- rameter to “80101 L1.” 1 Press the [DIMR(MW)] key to enable adjustment of the “TX Power (Low 1).” 1 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the RF Power Meter reading is 5 W (20.5 W). G Press the [D/MR(MW)] key. ‘TX Deviation 1 Inject a 1 kHz, 50 mV signal from the Audio Gen- erator. 7 Rotate the DIAL knob to set the alignment pa- rameter to “80101 dU.” 1 Press the [D/MR(MW)] key to enable adjustment of the “TX Deviation.” 7 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the Deviation Meter reading is 4.2 kHz (0.1 kHz) (EXP version: 4.5 KHz + 0.1 KHz). 7 Press the [D/MR(MW)] key. CTCSS TX Deviation GF Rotate the DIAL knob to set the alignment pa- rameter to “BO101 100.” 1 Press the [D/MR(MW)] key to enable adjustment of the “CTCSS TX Deviation.” G1 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the Deviation Meter, reading is 0.6 kHz (0.05 kHz). 7 Press the [D/MR(MW)] key. 1Alignment DCS TX Deviation 1 Rotate the DIAL knob to set the alignment pa- rameter to “BO101 dC.” 1 Press the [D/MR(MW)] key to enable adjustment of the “DCS TX Deviation.” G1 Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the Deviation Meter reading is 0.6 kHz (20.05 kHz). 1 Press the [D/MR(MW)] key. 12 Closing the Alignment mode Press the [DW(REV)] key to save the new setting and exit t normal operation. 2. Press and hold in the [PWR(@)] switch for 1/2 sec- epipetreisigs 3. Press and hold in the [MHz(SET)] key while turning the radio on.oy sunaSong qynoay, 4m NIVW240N 4n NIVW( pts) inofivy stave 4m NIVWo a a (a apis) mnohivy syavg 3 NIVINMAIN Unit Parts List REF DESCRIPTION | VALUE | VW [TOL | MFRS DESIG | VXSTOPIN | VERS. [LOT] SIDE [AVADA] ‘PCB with Components ‘C831 19006 _CE-OFF, DSTUSA (683119007 CEOFF.DSTEXP2 Printed Creu Board AAOZSROOO FROTS2A0E 1 ©7007 | CHIP TA CAP. Tour Tov “TAJATOEMOTOY K7s100072 pees 1002 | CHIPTA CaP. 10uF tov ‘TAIA106MO10Y K7100072 1/8 | 95 1003 | cHipcaP. oor |sov |e | GrMiessitHiosKao1p | K22174823 1 }B | ge ¢ 1008 | CHIPCAP. tur tov |F | GrMtasrtatoszaotD | K22105001, 1 }B | 65 © 1005 | CHIPCAP. soopr_ | sov | cH | GRMMBszctHtotuantD | K22174235, fa | Be ¢ 1006 | cHIpCAP. oootur |sov |B | GRMiesatiHtc2KAa1D | K22174821 fa | a2 C1007 | ALevecrRocaP. | saoour | 16v URICs2MHD 40129106 fa | ee ¢ 1008 | CHIPCAP. ser =| sov | cx | GraieeactHRsoczo1p | K22174201 1] A | 6 € 1009 | CHIPCAP. 150F Sov | Gi | GrwieszcrHisosaoiD | K22174215 a fa | 68 i011 | CHipcaP. coor |sov | 8 | GRMressitHic2KAoID | K22174821 fa lor C1012 | CHIPCAP. oootur |sov |B | GRMMesStiHto2KAoID | K22174821 a} a | cB 1013 | cHipcar. oootur |sov |B | GRMiessttHic2KAo1D | K22174821 fa | cB C1014 | CHIPCAP. oootur |sov |B | GRMtesstiHto2KAcID | K22174821 1 | A | 65 61015 | CHIPTA CaP. ozaur | 20v "TMCPID22eMTRF 78130069 1 }a | or ©1016 | CHIPTA CAP. ozaur | 20v “TMGPID22eMTRF 78130069 4. |A | 07 1017 | CHIPTA CAP. aur | 63V TEESVPOIS35MER Kr80800s2 a2} a | 06 C1018 | CHIPCAP. ooo |sov |B | GRMissatiHtceKaotD | «22178809 n-} A | or C1019 | CHIPGAP. oosur | 25v |B | GRanesartes73KAoID | Kz2t44811 1} A | 06 C1020 | CHIPCAP. coor |sov |6 | GRMnssarHiceKAotD | K22178809 1} A | 06 C1021 | cHipcaP. coor | sov | 6 | GRMneBSitHzeKAoD | Kz2174837 1 ]8 | as C1022 | cHIpcaP. coor |sov |B | GRMiessitHaz2Kao1D | K22174837 1 ]B | 6s 1028 | CHIPTACAP. tur 25 TEESVAIE105MBR K7e140013 +] | os 61025 | cHipcar cow | sov |e | GrwiessitHiosKaotp | K22174823 fe | as ¢ 1026 | CHIPCAP. oooz7ur |sov |8 | GRMissattHer2KAo1D | Kz2174816 1 }8 | a5 © 1027 | CHIPTACAP. tur 25 TEESVATE05MOR 76140013 1 ]B | as 1029 | cuipcaP. cow | sov |e | GrMressitHtcsKao1p | K22174823 1 }B | ge ¢ 1030 | CHIPCAP. oootur |sov |B | GRMMesstHicaKAoID | K22174821 fa |e ¢ 1031 | CHIPGAP. oootur |sov |B | GRMiesstiHtcaKAcID | K22174821 A | 83 1032 | CHIPGAP. oootur |sov | 6 | GRMresstiHto2KAo1D | Kz2174821 | A | 03 ¢ 1033 | cHipcaP. coor |sov |B | GRamessitHic2Kso1D | K22174821 fa | cs 1034 | CHipCaP. coor |sov |B | GRMiesstiHto2KAoID | K22174821 a fa | 5 1035 | cHipcaP. coor |sov |B | GRMressiiHic2Kao1D | K22174821 fa | oe € 1036 | CHIPCAP. 180 sov | ai | Grwisazctiteosaoio | K22174217 a fa | c8 ¢ 1037 | cHipcaP. 200F sov |ai | Graisezctzcouzo1n | K22174218 a fa | 68 6 1038 | CHIPCAP. Odour |sov |B | GRMiesBttHto2KAoID | K22174821 fA | 66 1039 | CHIPCAP. uF tov |F | GRMtasritatoszaotD | K22105001 fa | 08 ¢ 1040 | CHIPCAP. 15F | Sov | ck | GRMtBecIHtRSc2oID | K22174258, 1} A | 65 C1041 | CHIPCAP. oootur |sov |6 | GRMressitHtc2KAo1D | K22174821 fA | os ¢ 1042 | CHIPTA.CAP. tour tov ‘TAIAIO6MO10Y Kreto0o72 1. [A | 05 € 1043 | CHipcAP’ otur_ fev |B | GRaiesriciosKaotp | K22124805 a} A | 06 C1044 | CHIPCAP. coor |sov |B | GRMnesatiHtc2KAcID | K22174821 a} A | 05 C1045 | CHIPCAP. cootur |sov |B | GRMiesStiHto2KAoID | K22174821 1. | A | 06 C1046 | CHIP TACaP. 10uF tov ‘TAJA106MO10Y Kreto0o72 1] A | 06 € 1047 | CHIPCAP. ATF sov |ai | GRwisszctH47osaoiD | K22174227 1. | a | 07 1048 | CHIPCAP. 4ipe | Sov | Gi | GRweezcrHaTouao1D | K22174297 a} a | o7 C1049 | CHIPCAP. 4IpF sov |ai | GrwsazcrHa7osao1D | «22174227 a }a | o7 1050 | CHIPCAP. sep | Sov | GH | GRueszcrtsouaorD | 22174215, a fa | 06 €1051 | CHIPGAP. coor |sov |B | GRMesatiHtc2KAGID | Kz2174821 1 |B | a5 1052 | CHIPCAP. oozzur |sov |6 | GRMnessitHezsKAo1D | Kz2174859 1 ]B | es 1053 | CHIpcAP. oorsur |sov |B | GRMiessitHissKAo1D | K22174835 1 ]B | es 1058 | CHipCAP. ssopF | Sov | GH | GRuBazciHistuagiD | 22174299 1/8 | a6 1055 | CHIPCAP. seor =| sov |B | GRuiesstiH5e1KA01D | K22174806 +] | as € 1056 | ALevecTRO.cAP. | toour | 16v UvRICIO1MOD Kaorz9104 a} A | 85 1057 | chipcaP. otr | iev | 5 | Graisssrictoskaotp | k22124805 fa | Be € 1059 | CHIPCAP. oootur |sov | 6 | GRMiesStHto2KAoID | Kz2t74821 1/8 | 95 1060 | cHIPCAP. cootur |sov |B | GRMiessiiHicaKAo1D | K22174821 1 ]B | 95 C1061 | ALeLEcTROcAP. — | tour 16v UVRICI00MDD 40129103 fA | BS 1062 | CHiPCAP. cootur |sov |6 | GAMiesstiHtocKAcID | Kz2174821 + |B | 95 € 1063 | CHIPCAP. AIRF sov | ai | GrwisazctHa7osaoiD | K22174227 fA | 85 1054 | CHIPCAP. coor |sov |B | GRMresstiHto2KAoID | K22174821 a }a | ce ¢ 1055 | CHIPCAP. SF sov | ai | GraneszctHsRoczo1p | «22174206 fa | os ¢ 1066 | CHIPCAP. oF sov |ai | GraisezctHsRoczoip | «22174206 a} A | 65 1067 | cHIPCAP. Spr sov | ai | GrasszctHsroczo1p | «22174206 ala |e € 1068 | CHIPCAP. THF sov | oH | GrMies2crH7RODz01D | K22174208 fA |e ¢ 1069 | CHIPCAP. ATF Sov |ai | GrueszctHa7osao1D | K22174227 fa |S ¢ 1070 | CHIPCAP. soopF | Sov | cH | GRutBazctHtotsaotD | K22174235, fA |B C1071 | cHipcar. oootur |sov |B | GRMiessitHto2KAo1D | K22174821 ala ler C1072 | CHIPCAP. tof =| Sov. | GH | GReMBazcHHtoquADID | Ka2174211 fA |B 61073 | CHIPCAP. arr f6av |B | sMKtO7BUa75MAT Kz2084803 fa |S C1074 | CHIPCAP. ootur |sov |B | GRMesattHtcaKAcID | K22174821 lA |S 1076 | CHipCaP. oor |sov |B | GRMnessitHic2KAoID | K22174821 la |S C1077 | CHIPGAP. ovr |sov_|B | GawissatiH2z3KaotD | K22174899 |e jes aMAIN Unit Parts List REF | DESCRIPTION | VALUE [vw [TOL MFR'S DESIG ‘VXSTO PIN | VERS. LOT] SIDE [AYADA] ©1078 | CHIPCAP. O.015uF | 50v | 8 | GRMIBBBITHTSSKADTD | Kz2174898 +18 [es Gore | cHipcaP, ssopr | Sov. | cH | GransezcinisisaotD | Ka2174230 |B | ee 1080 | cHpcAP, s6opr_ | sov | od | GAMBE2CIHS6iJA0ID | K22174273, 1 |B | 66 C081 | cHpcaP, coor | sov |B | GrMieasiHtoaKAcID | Kz2174821 + |B |g ioe2 | ALeLEcTROcAP. | toour_ | 18v USRICIOINDD. Ke0120110, fa |e i083 | chipcaP. coor | sov |e | GRrMieasitoaKacio | K22174821 ve |i 1084 | CHIPcAP, coouF |sov |B | GRMiBseitHro2KAoID | Kz2174e21 |B |e C1085 | cHpcA, zap | ov | A | GrMBB2ctHzaoJA01D | Kz2174219 ula lor toas | cHIpcaP owe | sov |e | GrMieaarHioaKaoD | 22174823, |B | a6 4089 | CHIpcAP, osu = [tev |B | GrMieasricrosKAgTD | K22124008, tla | As 1080 | CHIPCAP, coir | sov |B | GRMieseItHTOsKAoID | Kz2174823, |B |S 1091 | CHIpcAP, s20pF | Sov. | cH | GawezcHizisaoID | Ka2174237 tla [os to82 | cHipcaP, oor | sov |B | GrMiessiirOaKAo1D | KZ2174823, + |B |os 083 | CHIPcAP, ‘zope | Sov. | GH | GawisezcrHizisaotD | Ka2174237 tla |e 1084 | cHipcaP, oosur | 25v |B | GrMieaattEd7aKAOID | K22144011 ra [os 1086 | CHIPCAP, ooaruF | 25v | 8 | GRMIBBBITEA7SKAOID | K22t44811 r la |os 1098 | CHIPcAP, ooos7ur | sov | 8 | GAMIBBBITHS72KAOID | K22174817 tla los 089 | CHIPCAP, dour | tev |B | GRMOBA73KI6PT 22124808 |B les C1099 | cHIpcaP, ooarur | 25v |B | GAMeBBITE47aKAOID | K22144811 v |B | es 1101 | CHPCAP coor |5ov | 8 | GrMiessitHToaKAoD | Kz2174809 + |B | o C1101 | CHipcaP, ooowF | sov |B | GRMIeBBITHIOaKAOID | Kz2174821 |B | 0 1102 | CHpcAP, coor |sov |S | GRMBBITHi0aKAGID | Kz2T74821 |B | 9 C1103 | cHipcee, coor | sov |S | GrMesBiHi0aKAo1D | Kz2174821 ale lis C104 | cHpcaP, ooowr | sov | 8 | GRMiessiiHio2KAcID | K22174821 le |i C1105 | CHipcAP, tgpr | Sov | cH | GramisezcinisosaoiD | Ka2174215 tla loa G08 | cHipca, ooowr |sov |B | aRMiessiiioaKacD | Kz2t74821 la le C1107 | cHpcAP, coouF |sov | 8 | GRMiBBBItHi02KAoID | Kz2t74e21 x la loo C1108 | cHpcaP, spr | Sov. | cH | GaMtsszcrtsoJAotD | Kazt7aat5 fa lo C09 | cupcaP. coor |sov |B | crMieasiiio2KaciD | Kz2174021 la lo Gato | cHpcaP, ooowr | sov |B | GrMeaBiHTo2KAoID | Kz2t74821 cle | c1ntt | cHpoap, osur | tev || GRMBBBITcTOaKAOTD | K22124805 lA | He Gin2 | cuca, oor |sov |S | GAMiessitHtosKAoD | Kz2174823, + |B | a6 Cina | cupcar, ooowr |sov |e | GRMieasrtoaKac1D | Kz2174821 va |e Citta | ceca, aie | 50v | 4 | GaMBsactHe7oJA01D | Kza174207 la |os Cats | CHIPTACAP. sour | tov ‘TAJAtOeMG 10 xk7e100072 rer C16 | cHpcee, ame | sov | oa | GrMisactHs7osao1D | K22174227 ra los Can? | cHpcee, one =| tev |B | GrMeaBricrosKaotD | K22124805, la los Cina | cHPpcAP, osur | tev |B | GRMTeaBIicrosKAoTD | K22124805, tla |oe Cans | cHpcar, oor |sov | 8 | GrmieasiHtoaKaoiD | K22174823, + |B |e 61120 | CHIPCAP, oossur | tev |R | GRMIBERIICSs3KAOID | Kz2124801 |B | a C1121 | cHpcar, ooa7ur | 25v |B | GAMIBBBITEA7IKAOID | Kz2144811 + |B | be C1122 | CHIpcAP, OozuF | 50v |B | GRMIBBBITHZ2sKAOTD | K22174859 |B | a4 C1123 | cHpcee, osu [tev | | GAMieaBiicrosKAaTD | K22124805 vB | as Citza | ALELECTROCAP. | touF | 18v REZ-16VI00MES# ka0129008 vila jaz 61125 | cHpCAP, coor |sov | 8 | GRMTBBBITHTOZKAGID | 22174821 ala ler C1126 | CHpcaP, coor | sov |S | GrMtessitHioaKAoID | Kz2t7aeat la |e C1127 | cHpceP, ooouF |sov | 8 | GRMIBBBITHIOaKAOID | Kz2174821 ala ler C128 | cHpcer, ooowr | sov |S | GrMieasiHioaKactD | K22174821 |e | re 1129 | CHIpcAP coouF |sov | 8 | GrMieseitHioaKAoID | Kz2t74821 la ler G1130 | CHipca, ame |sov |x | GrMisszctHerouaoiD | Kzztraz27 v/a |e 1131 | CHIPCAP, sapF | s0v. | G4 | GRMeezctHszouA01D | Kz2174223, la lo C1132 | CHipcaP, supe | Sov | | GramaazcrHszouaniD | Kz2174223, la |e C1133 | cHpcar, doowr |sov |B | GRMiBeaiHio2KAgID | 22174821 rla la C434 | CHipcar, ooowr | sov | 8 | GRMesBIIHTO2KAOID | Kz2tra821 cla |e 1135 | cHPpcaP, coor |sov | 8 | GrMiessitHioaKaciD | Kz2t7482t va |os C1136 | CHipcAP, ooowuF |sov | 8 | GRMiBBIHI0aKAOID | Kz2174821 ra |os C37 | cHpcar, sape|sov [oH | GrMisezctHseouaoiD | Kz2174225, va | oo C1138 | CHipcaP, aapr | 50v | ot | GrMsezciMasouzorD | K22174226, vila |os C1139 | cHpcaP, oosur | 25v |B | GRMiBaatEd7aKAOID | K22144011 v |B |os G10 | cHIpcaP, coor | sov |B | GRMiBeBiiHioaKAcID | 22174824 + |e [nt ins | CHpcAR, coor |sov |S | GAMiBaBitHi0aKAo1D | 22174821 + ]B [nt Cin2 | cHPpcAP, osur | tev |B | GAMtBBBIIcTOsKAOTD | K22124805, + |B [ns Cia | cHpcar, ooowr | sov | 8 | GAMieasiiHtoaKAo1D | Kz2174821 |B | 96 Cima | ALevecTROcA. | a7our | t8v UVRICATIMED. Ke0129108, vila | Ra Cus | cHipcee, osur | tev |B | GRMreBBrictosKAotD | K22124805 + |B | 96 iis | cHpcar, ooowr | sov | 8 | GRMigaariMtoaKanID | K22174821 |B | he Ciw7 | ALeLecTROcAP. | 220uF— | 18v WvRICZ21MED. 40129105 ula far Cina | cHipceP, ame | sov [oa | GrMsszcta7oszor | Kz217e228 ula ler C119 | CHpcAP, coor | sov |S | GRMIBBBITHIO2KAOID | 22174821 la |e 150 | CHipcae ooowr | sev |B | GRMIBaBiHtoaKAaID | K22174821 [a | ee 61151 | CHIPCAP, coor |sov |B | GRMISSBITHTO2KAOTD | K22178609 la ler C1152 | cHpcaP, ooowr | sov |B | GAMieaBiHr02KAa1D | Kz2174821 |B | es 61153 | CHIPCAP coor |sov |B | GRMIsseitHto2KAoID | K22178609 va ler C1154 | CHipcaP, ooowr | sev |B | GRMieaBiHToaKAoID | K22174821 cla | ee 6.1155 | CHIPCAP, coor | sov | 8 _| GRMISSBITHTOZKAOTD _| K22178609 vla_|r 18