User Manual

Speed gates SBTL8000 series

Applicable Model(s): SBTL8000, SBTL8011, SBTL8022, SBTL8033, SBTL8200,
SBTL8211, SBTL8222, SBTL8233

Version: 1.0

Date: June 2019

 Contents

1. Product Introduction ............................................................................................................................................................. 1

1.1 Model number and access control ...................................................................................................................... 1

1.2 Chassis design and dimensions ............................................................................................................................. 1
1.3 The mechanical system of the speed gates .................................................................................................. 2
1.4 Electric control system ................................................................................................................................................. 2
1.5 Operation principle of the speed gates............................................................................................................ 3
1.6 System composition of the product ................................................................................................................... 4
1.7 Specifications...................................................................................................................................................................... 4

2. Installation of the Product .................................................................................................................................................. 5

2.1 Installation notes .............................................................................................................................................................. 5

2.2 Installation position of the speed gates ........................................................................................................... 5
2.3 Cables installation and fixing ................................................................................................................................... 6

3. Menus .............................................................................................................................................................................................. 9

3.1 Menu operations .............................................................................................................................................................. 9

3.2 Menus ...................................................................................................................................................................................... 9
3.3 Functions introduction of wiring and terminal .........................................................................................12

4. Troubleshooting .....................................................................................................................................................................13

5. Product Maintenance..........................................................................................................................................................14

5.1 Chassis ...................................................................................................................................................................................14

5.2 Movement ..........................................................................................................................................................................14
5.3 Power .....................................................................................................................................................................................14
1. Product Introduction
1.1 Model number and access control

Access
C3-200 and inBio 260 and 2* 2*Facedepot 7B
None
2*Wiegand reader FR1500/ID reader device
Model

SBTL8000 √

SBTL8011 √

SBTL8022 √

SBTL8033 √

SBTL8200 √

SBTL8211 √

SBTL8222 √

SBTL8233 √

Figure 1-1

1.2 Chassis design and dimensions

The SUS304 stainless steel body looks simple and clean and is anti-corrosion. The SBTL8000 series
grants legal access to the authorized persons and restricts illegal access. In case of an emergency, the
lock will release to allow fast evacuation and egress.

Below is the design and dimensions of SBTL8000:

SBTL8000 series User Manual 1

 Figure 1-2

1.3 The mechanical system of the speed gates

The mechanical system of the swing turnstile is composed of the cabinet and the core mechanism.
The cabinet is equipped with the mode indicator, the infrared sensor, and the locking system. The
core mechanism mainly consists of the motor, the chassis, the core, and the swing arm (the glass
panel).

1.4 Electric control system

The electric control system of the swing turnstile is mainly composed of the master control panel, the
infrared sensor, the mode indicator, and the loudspeaker.

Master control panel: The master control panel is the core part of the control system that receives
signals from the photoelectric switch, performs logical judgment and processing of these signals, and
issues executive commands to the mode indicator, the servo motor driver and the loudspeaker.
Infrared sensor: It detects the location of the pedestrian and plays a safe protection function.
Mode indicator: This indicator shows the current passing mode status of the channel and guides the
passenger to pass the passage orderly and safely.
Loudspeaker: The system will trigger the alarm if it detects any unauthorized entry to the lane.

2 SBTL8000 series User Manual

1.5 Operation principle of the speed gates

 When the device is connected to the power, the system will perform self-check. The device will
operate normally if no problem is detected. If a failure is detected, the system will display related
messages on the LCD display screen so that the user can have a quick knowledge of and solve
the problem.

Air switch

Figure 1-3
 When the reader detects a valid card/fingerprint, the display screen will show whether it is
successful or not. And the switch instruction signal is transmitted to the master control panel.
 After receiving the signal from the reader and the infrared sensor, the master control panel will
send valid control signals to the servo motor driver. At this time, if the system is in forbidden
passing mode, the mode indicator light will turn red, and the master control panel will not accept
signals of card swiping/fingerprint scanning.
 After the passenger passes the channel according to the opening direction of the swing arm, the
infrared sensor will keep detecting the movement of the pedestrian throughout the passage and
continue to deliver signals to the main control panel until the pedestrian passes through the
passage.
 If the pedestrian enters the passage but forgets to swipe his/her card, or if the card held by the
passenger is invalid, the system will prompt an audible alarm to warn the pedestrian to stop
passing. The alarm signal will not be cancelled until the passenger retreats from the passage. A
pedestrian can pass through the lane only after successful verification with a valid card read by
the card reader.

SBTL8000 series User Manual 3

1.6 System composition of the product

The single-passage management system is composed of two single-core speed gates. The multi-
passage management system is composed of two single-core barriers and multiple dual-core barriers.

Working modes of the system

To meet different needs, this system provides multiple working modes for users, including the normal
working mode, normally open mode, normally closed mode, and testing mode.

After supplying power to the device, the LCD screen on the control board will display a default state,
which is the current working mode.

1.7 Specifications

Dimension (mm) SBTH1000: L = 1600, W =120, H = 1022

Communication CAN Input voltage AC110~240V, 50-60Hz

Input control signal Switching signal Output voltage DC 24V

Time of 20% - 95%

0.8 Sec (adjustable) Relative humidity
opening/closing (Non-condensing)

Temperature -28℃ to 60℃ Passage rate Maximum 30/minute

Infrared sensor 10 Working environment Indoor

4 SBTL8000 series User Manual

2. Installation of the Product
2.1 Installation notes

1) It is recommended that the speed gates must be installed on a horizontal solid platform with a
height of 50mm to 100mm.
2) It is also recommended that the swing turnstile should not be used in a corrosive environment.
3) Make sure the protective ground wire of the system is reliably connected to avoid personal
injuries or other accidents.
4) The equipment shell is made of stainless steel. You may gently remove any dirt or dust on the
surface with a soft and smooth fabric. Do not scrub the surface with hard objects. Do not rinse
the device with water, otherwise there may be short circuit or damaging the equipment.
5) After installation, check if the connection is done correctly at the connecting points of the
protective ground wire, at the connector assemblies and wiring points of the circuits, as well as at
each movable part of the speed gates turnstile. Any loose nuts, screws and other fasteners should
be tightened in time to avoid speed gates turnstile failures caused by longer operations.

2.2 Installation position of the speed gates

A distance of 100mm between the speed gates turnstile and the wall needs to be reserved for ease of
opening the top cover of the machine to perform maintenance and adjustment. The reference figure
is shown below:

SBTL8000 series User Manual 5

 Figure 2-2

2.3 Cables installation and fixing

For the outlets of the concealed cables, please refer to the drawing indicating the mounting holes.
The input voltage for this swing turnstile is AC110-220V, and its master and slave are connected with
an 8-core cable (signal) and a 2-core cable (power). When installing the speed gates turnstile, the
user only needs to connect it to the corresponding ports. Note that the PVC conduits are laid 100mm
under the ground, with the height of the exposed part not exceeding 100mm. In addition, the
conduit outlet is bent to prevent the ingress of water into the conduit.

SBTL 8000 series installation holes and cabling positions are as shown in Figure 2-3a:

6 SBTL8000 series User Manual

 Figure 2-3a

Mark the anchor hole at the centre of the stand, and the edge of the chassis base on the ground
according to the size as shown in Figure 2-3a. Use a hammer drill to drill M12 screw holes, then install
the screws. Place the swing turnstile according to the size and respective installation position as
shown in the figure before installation and fixing. Connect the turnstile to the power supply and

SBTL8000 series User Manual 7

perform a power-on test. If the test is passed, tighten the screws. It is recommended to mark a
warning line on the ground, as shown in Figure 2-3b, after installing the device to remind the
pedestrian to stand behind the line when swiping the card.

Figure 2-3b

8 SBTL8000 series User Manual

3. Menus
3.1 Menu operations

 Operating instruction
1) After powered on, the LCD screen on the control board will display the default state showing the
current working mode.

2) There are 4 buttons on the control board: UP, DOWN, ENT, and ESC, as shown in Figure 3-1.

UP: to move upwards or increase the value.

DOWN: to move downwards or decrease the value.

ENT: to enter a menu setting item or confirm the current modified value.

ESC: to return to the previous menu or cancel the current operation.

3) Operation and instruction of menu

Press the ENT button and enter the password input interface. The default password is: UP, UP, DOWN,
DOWN, DOWN, DOWN. You may press the ESC button to erase the last input. After entering the
menu, press UP or DOWN to choose a menu item, then press ENT to enter the interface and adjust
such function or value.

3.2 Menus

1. Position adjustment of the swing barrier

Type: zero (default)
Left limit
Right limit

2. Passing mode
Opening mode: Two-way swipe (default)
Left free, Right swipe
Left swipe, Right free
Two-way free
Left prohibit, Right swipe

SBTL8000 series User Manual 9

 Left swipe, Right prohibit
Left prohibit, Right free
Left free, Right prohibit
Two-way prohibit

3. Opening duration (Press ‘ENT’ to modify)

After the gate is opened, it will automatically close if no one passes through within a certain time
duration. The default value is 5 seconds. The value ranges from 2 to 60.

4. Reverse intrusion
Mode: Close the door and voice alarm
Voice alarm only (default)
Turn off reverse detection

5. Trailing alarm detection

Mode: Turn off trailing detection
Voice alarm only (default)
Close the door and voice alarm

6. Opening speed
Speed value: 1~20 (default 1)

7. Closing speed
Speed value: 1~20 (default 1)

8. Swiping mode
Method: Allow the card to be swiped in the channel (default)
Do not allow card swiping in the channel

9. Reset counter
Reset: Out counter (default)
Into the counter
All

10. Gate closing delay time

Time: 0~10 (default 0)

11. Brake unlock mode

Mode: Delay unlock (default)

10 SBTL8000 series User Manual

12. Brake starting angle
Angle: 1~10 (default 3)

13. Fire alarm signal

Signal: right open
Left open (default)
Shut down

14. Volume setting

Volume: off
The value ranges from 1 to 16 (default 5).
1 is the minimum value; 16 is the maximum value.

15. Audio prompt for gate opening swift

Enable or not: No (default)
Yes

16. Infrared anti-pinch

Mode: Turn off the anti-pinch feature
Enabling anti-pinch (default)

17. Infrared anti-pinch area

Area selection: Disable during In and out of infrared (default)
All infrared zone anti-pinch

18. Memory opening

Whether to open: No (default)
Yes

19. System working mode

Mode: working mode (default)
Test mode
Restore to factory

20. Version number:

Version: V9.0.0

SBTL8000 series User Manual 11

3.3 Functions introduction of wiring and terminal

Figure 3-2

12 SBTL8000 series User Manual

4. Troubleshooting

Number Failure descriptions Analysis and solution

Check that the control panel mode

The mode indicator light does not
1 indicator wiring is correct or that the
respond or the indication is incorrect.
contact is poor.

Check the mode setting of the master and

After swiping the card, there is only a slave devices and the 8-core, 2-core
2
speed gate unlocked. connection lines. See the wiring diagram
for the specific connection circuit.

Check to see if the opening delay time is

The barrier doesn’t close when the
3 too long or whether the IR sensor is
opening delay time is ended.
covered.

When the gate is self-tested, the swing In the process of self-test, there are
4 arm is not in the normal closing obstacles, please remove the obstacles,
position! restart the self-test after power-on!

SBTL8000 series User Manual 13

5. Product Maintenance
5.1 Chassis

The chassis is made of SAE 304 stainless steel. When the device has been used for a long period, there
may be rust or stain on the surface of the chassis. Remember to regularly sand the surface along the
grain softly and carefully, then coat the surface with anti-rust oil. Avoid covering the infrared sensors.

5.2 Movement

Cut off the power supply before maintenance. Then, open the door, wipe off dust on the surface, and
lubricate the transmission mechanism. Check and tighten others connection parts.

5.3 Power

Cut off the power supply before maintenance. Check the plug connection; if anything is loose, fix it.
Do not randomly change any connection positioning. Check the external power supply insulation
regularly. Do periodic check for any kind of leakage. Check if the technical parameters of each
interface are normal. Check the service life of the electronic components.

Caution: The above-mentioned maintenance method of the speed gates, especially the movement
and the electric control maintenance, must be carried out by professional personnel. Always
remember to cut off the power supply before maintenance and repair.

14 SBTL8000 series User Manual

www.zkteco.eu

Copyright©2019 ZKTECO CO., LTD. All rights reserved.