B.O.

CONSTRUCTION OF A MAIN DISTRIBUTION WATER TANK WITH A CAPACITY OF 1800 M³ IN QISHN CITY, AL MAHARAH GOVERNOR

IUS-AF2-UWS-QSHN-001
STRUCTURAL & ARCHITECTURAL

Unit Price(USD)
Item No. Unit Qty
Figures Figures
Description
General Note:
all work as per the specification and to the Drawings of the Engineer

1 Excavation & Backfilling for building

1.1 Excavate in any type of soil and removal of excavated soil not used for fill to disposal
Areas approved by local authorities (quantities are measured from architectural zero m3 850.00
level )
1.2 Fill with clean sand , compacted m3 70.00

2 Concrete Works
Ordinary Portland cement is to be used for all construction elements unless otherwise
indicated items
2.1 Plain concrete
2.1.1 Plain concrete under the footing thickness of 10 cm with strength 200 kg/cm2 with
m3 85.00
cement content 300 kg/m3. (using sulphate resistant cement).
2.1.2 Ditto for slopes in tank floor 10cm average m2 300.00
2.1.3 Supply and construct for roof slopes 10cm average thickness with strength 200 kg/cm2
m2 395.00
with cement content 300 kg/m3. (using sulphate resistant cement).
2.2 Reinforced Concrete
 .Reinforced concrete items include forms and excludes reinforcement - PVC water bars
are measured in waterproofing B.O.Q

Supply, casting and finishing of reinforced cement concrete (Grade f'c 4000 psi)
minimum compressive strength of 28MPa at 28 days), cement content not less than
350kg/m3 with suitable additives,steel rebar shall conform to ASTM A-615M with
minimum yield stress of 4200kg/cm2, for tank's base, foundations, columns, beams, walls
and roof. The work includes providing all required materials of high quality and approved
(Steel, cement, sand, aggregate, water, etc.). Also, the price includes supply and
installation of approved solid rubber water stop strip, providing and laying insulation
layer consist of bitumen membrane 4mm and 3coats of hot bitumen (75/25) for the
foundations of the tank, s and all necessary accessories complete as per drawings,
specifications and instructions of the Engineer

2.2.1 CONCRETE (CONT'D)

Concrete of grade (Special), 35N/mm2 with water proofing admixtures
2.2.1.1 For raft (using sulphate resistant cement) m3 335.00
2.2.1.2 For walls m3 295.00
2.2.1.3 For columns, beams and ceiling m3 200.00
2.4 Supply and install of PVC waterstop 24cm width for construction joints
m 165.00

3 Damp proofing & Waterproofing Insulation

Rates cover all specified layers
3.1 Supply and construct non toxic Epoxy paint of water tanks to inside wall and floor of the
tank in three layers. The price includes all necessaries for the completion of the works,
according to the specifications, drawings and instructions of the Engineer.
3.1.1 Floors m2 400.00
3.1.2 walls m2
730.00
3.1.3 Internal ceiling m2 520.00
3.2 External waterproofing consisting of primer 2 layers of torch applied membrane , 4mm
thick
3.2.1 Below foundations including 3cm top cement mortar m2 540.00
3.2.2 For walls including protective boards m2
185.00
 3.3 Ditto one layer for roof
3.3.1 Vertical m2 35.00
3.3.2 Horizontal including 3cm top cement mortar m2 395.00
3.4 Galvanized steel flashing m 80.00
3.5 Crystaline waterproofing for water tank m2 705.00

4 Thermal Insulation
4.1 Thermal insulation of extruded polystyrene boards 5cm thick m2 395.00
 5 Floors
5.1 Supply and construct of the Cement tiles 200 x 200 x 20mm. include sand fill, mortar,
pointing and finishes as required the price includes all necessaries for the completion of m2 395.00
the works, according to the specifications, drawings and instructions of the Engineer.
5.2 Skirting
5.2.1 Cement skirting 10mm height m 80.00
6 Plaster
Supply and construct plastering works with plasticizing admixtures for internal and
external surfaces with mortar (1:3). The price includes all necessaries for the completion
of the works, according to the specifications, drawings and instructions of the Engineer

6.1 Cement plaster for external surfaces including reveals. m2 510.00

7 Paint
7.1 Acrylic paint for external surfaces, resistant to ultraviolet rays. m2 510.00

8 Miscellaneous
8.1 Supply and install electrostatically coated aluminium ladder fixed with grout No 2.00
9 Side protection pavement:
Supply and construction of side protection pavement around the new ground water tank
1800m3 of cement tiles (25x25x2.5)cm of high quality. The work and price include
excavation works, supply and installing concrete curbs (50x35x15), backfilling
constructed in layers with watering and compacting , 10 cm plain concrete with 10cm M.L 99.00
sound stone fractions layer,Stone buildings surmounted by concrete curbs, curing with
water properly for no less than seven days, and doing all it takes to finish the work
according to the specification, technical rules, and the engineer's instructions.

10 Supply and installation galvanized steel Ladder with Safety Cages of 76 cm width and
different heights as per drawings with protection cage on the tank frame from outside.
The price includes all necessaries for the completion of the works according to the L.S 1.00
specifications, drawings and instructions of the Engineer.
11 Safety Rails
Supply and install galvanized steel safety railing to the reservoir roof with height of 1.1
meter, and all necessary bolts and fastenings for connecting to the concrete wall. The M.L 90.00
price includes all necessaries for the completion of the works according to the
specifications, drawings and instructions of the Engineer.

12 Steel hopper cover.

Supply and installation of roof Access lockable hopper HD cover 80x80 cm. work
includes providing all fittings and materials required( tube, handles, lock, support arm, No 2.00
ect.), skilled labor, and doing all it takes and needs to finish the work according to the
technical rules, drawings and the engineer's instructions.

13 Geotechnical Investigation Works at Tank Area

"Scope of Work:
• This work consists of subsoil investigation for Tank Area which includes the drilling of
boreholes manually, coring and carrying out field and laboratory test.
• Works shall be carried out in accordance with ASTM STANDARDS (AMERICAN) for
Soils for Civil Engineering Purposes""." M.L 20.00
Carrying out geotechnical soil investigation work in overburden comprising all type of
soil and drilling bore holes manually. The work including providing & supply of wooden
core boxes for samples, logging of all bore holes and also includes preparation of reports,
conducting of various field & laboratory tests as indicated in specification :

14 Supply, installation, and maintenance of project signboard(1.6m x 1.4m and 1.2m from
ground) as per drawing, material similar to specified large sign support. The following
information will be written in Arabic and English Languages as shown in attached No 2.00
drawings, and any other information instructed by the Employer/Engineer.

Grand Total
 B.O.Q

A CAPACITY OF 1800 M³ IN QISHN CITY, AL MAHARAH GOVERNORATE

Total Price (USD)

 B.O.Q

CONSTRUCTION OF A MAIN DISTRIBUTION WATER TANK WITH A CAPACITY OF 1800 M³ IN QISHN CITY, AL

IUS-AF2-UWS-QSHN-001
PLUMBING WORKS

Item No.

PLUMBING WORKS

1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14

3.15

4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.1

6
7

8
Grand Total To Construction Works
 B.O.Q

CONSTRUCTION OF A MAIN DISTRIBUTION WATER TANK WITH A CAPACITY OF 1800 M³ IN QISHN CITY, AL MAHARAH GOV

IUS-AF2-UWS-QSHN-001
PLUMBING WORKS

Unit
Description

PLUMBING WORKS

Supply and Installation of Ductile Iron flange Pipe and Fittings for storeg tank
Supply, erection, testing and delivery in good working condition according to technical specification and
drawings of the following equipment:
OUTLET TO DISTRIBUTION NO.1
DN 300 Stainless Steel STRAINER BASKET. No
DN 300 DI Pipe, PN 16, K9 Double Flanged Pipe with puddle flange L= 1.4m No
DN 300 Butterfly Valves with a Resilient Seat, PN 16, operated by Lever. No
DN 300 Dismantling piece DI, Flanged, PN 16, Includes Gaskets and Bolts No
DN 300 Double flange pipe piece Length L =2.30m No
DN 300 DI, PN 16, Double Flanged Bend 90 deg.including all nessery the rainforce concret thrust block. No
DN 300 DI Pipe, PN 16, K9 Double flange pipe piece Length L =3 m PN 16 No
DN 300 DI Pipe, PN 16, K9 Double flange pipe piece Length L =1.7 m PN 16 No
DN 300 DI Pipe, PN 16, K9 Double flange pipe piece Length L =1.3 m PN 16 No
DN 300 Blank Flange No
OUTLET TO DISTRIBUTION NO.2
DN 400 Stainless Steel STRAINER BASKET No
DN 400 DI Pipe, PN 16, K9 Double Flanged Pipe with puddle flange L = 1.40M No
Double Flanged Reducer DN400/300 DI Pipe, PN 16, K9 No
DN 300 Butterfly Valves,Resilient Seat, PN 16, Lever Operated, No
Flange Adaptor DN 300 mm No
DN 300 DI Pipe, PN 16, K9 Flanged spigot pipe Length L = 90cm No
DN 300 DI, PN 16, Double Flanged Bend 90 deg.including all nessery the rainforce concret thrust block. No
Double Flanged Reducer DN300/200 DI Pipe, PN 16, K9 No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =1.90m No
Electromagnetic Flow Meter DN 200 No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =90cm No
DN 200 Butterfly Valves with a Resilient Seat, PN 16, operated by Lever. No
DN 200 Dismantling piece DI, Flanged, PN 16, Includes Gaskets and Bolts No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =1.20m No
Double Flanged Reducer DN300/200 DI Pipe, PN 16, K9 No
DN 300 Flanged socket No
DN 400mm OVER FLOW & DN 200mm Washout
DN 200 flanged Bell mouth DI, PN 16. No
DN 200 DI Pipe, PN 16, K9 Double Flanged Pipe with puddle flange L = 1.90M No
DN 200 Gate Valves with a Rising Stem, PN 16. No
DN 200 DI, PN 16, Double Flanged Bend 90 deg. No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =1.93m No
Double Flanged Reducer DN400/200 No
DN 400 flanged Bell mouth No
DN 400 DI, PN 16, Double Flanged Bend 90 deg.including all nessery the rainforce concret thrust block. No
DN 400 DI Pipe, PN 16, K9 Double Flanged Pipe with puddle flange Length L = 1.80M No
DN 400 Double flange pipe piece Length L =1.89m No
All flanged Tee DN400/400/400 No
DN 400 DI Pipe, PN 16, K9 Flanged spigot pipe Length L = 2m No
DN 400 Flanged Socket No
DN 400 Flap Valve No

Supply and Implementation of chamber and Pipes uPVC, DN 315 mm to wadi as shown on the standard
drawings, including excavation, backfilling, restore the existing surface to original status or as necessary,
L.S
this item covers all materials, labor, and equipment required for the connection, along with all necessary
measures to ensure compliance with specifications, drawings, and the Engineer’s instructions.

INLET No.1
DN 250 DI, PN 16, Double Flanged Bend 90 deg. including all nessery the rainforce concret thrust block. No
DN 250 DI Pipe, PN 16, K9 Double Flanged Pipe with puddle flange Length L = 1.10M No
DN 250 DI Pipe, PN 16, K9 Double flange pipe piece Length L =4.60m No
Double Flanged Reducer DN250/200 DI Pipe, PN 16, K9 No
DN 200 Altitude Valve PN 16 with Pilot-Controlled, Stainless-Steel Trim No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =75cm No
DN 200 Gate Valves PN 16 with Non-Rising Stem, No
DN 250 DI Pipe, PN 16, K9 Flanged spigot pipe Length L = 2m No
DN 250 floating valve No
DN 250 DI Pipe, PN 16, K9 Double flange pipe piece Length L =3.80m No
INLET No.2
DN 200 DI, PN 16, Double Flanged Bend 90 deg. including all nessery the rainforce concret thrust block. No
DN 200 DI Pipe, PN 16, K9 Double Flanged Pipe with puddle flange Length L = 1.10M No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =4.78m No
Double Flanged Reducer DN 200/150 DI Pipe, PN 16, K9 No
DN 150 Altitude Valve PN 16 with Pilot-Controlled, Stainless-Steel Trim No
DN 150 DI Pipe, PN 16, K9 Double flange pipe piece Length L =1.11m No
DN 150 Gate Valves PN 16 with Non-Rising Stem, No
DN 200 DI Pipe, PN 16, K9 Flanged spigot pipe Length L = 2m No
DN 200 floating valve No
DN 200 DI Pipe, PN 16, K9 Double flange pipe piece Length L =3.80m No
Supply and install a mechanical coupling or transition fitting to connect the existing INLET HDPE PN16
pipe to the new INLET ductile iron pipes. as shown on the standard drawings, including excavation,
backfilling, restore the existing surface to original status or as necessary,This item covers all materials,
labor, and equipment required for the connection using mechanical joint (MJ) fittings. Perform pressure
testing and inspection to confirm the integrity and leak-free operation of the connection. The scope of work L.S
and pricing includes the supply and installation of the INLET 1 & 2 pipeline and its connection to the
service room in the RCC water tank, along with all necessary measures to ensure compliance with
specifications, drawings, and the Engineer’s instructions.
Provide, install, and connect the existing outlet galvanized pipe line to the new ductile iron pipe PN 16, K9
(DI outlet). as shown on the standard drawings, including excavation, backfilling, restore the existing
surface to original status or as necessary,This item covers all materials, labor, and equipment needed for the
connection using suitable fittings. Perform pressure testing and inspection to verify the integrity and leak-
free functionality of the connection. The scope of work and pricing includes the supply and installation of L.S
the outlet pipeline and its connection to the service room in the RCC water tank. The price incorporates all
necessary tasks to complete the work in line with specifications, drawings, and the Engineer’s directives.

Supply and Implementation of valve chamber as shown on the standard drawings, including excavation, backfillinNo
Grand Total To Construction Works
N CITY, AL MAHARAH GOVERNORATE

Unit Price(USD)
Qty Total Price (USD)
Figures Figures

1
1
1
1
1
1
1
1
1
1

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

1
1
1
2
1
1
1
2
1
2
1
1
1
1

3
1
1
1
2
1
1
1
1
1

3
1
1
2
1
1
1
1
1
1

1
1