IOT LAB Program Manual

(Model No: IOT Kit-IES., Rev: 1)

Program Manual

TECH&SALES SUPPORT
Email: [email protected]
Mob No: +91 9840838264
Web: www.ielecsystems.com
Exp:8 To implement LED Blink and LED Pattern With Arduino.
a) LED Blinking.
Connection Details For LED Blinking
LED’S Arduino Uno
LED1 13
LED2 12
LED3 11
LED4 10
Program:
void setup() {
pinMode(13,OUTPUT);
pinMode(12,OUTPUT);
pinMode(11,OUTPUT);
pinMode(10,OUTPUT);
}
void loop() {
digitalWrite(13,HIGH);
digitalWrite(12,HIGH);
digitalWrite(11,HIGH);
digitalWrite(10,HIGH);
delay(1000);
digitalWrite(13,LOW);
digitalWrite(12,LOW);
digitalWrite(11,LOW);
digitalWrite(10,LOW);
delay(1000);
}
Exp:8 To implement LED Blink and LED Pattern With Arduino.
b) LED Pattern.
Connection Details For LED Pattern
LED’S Arduino Uno
LED1 13
LED2 12
LED3 11
LED4 10
LED5 9
LED6 8
LED7 7
LED8 6
LED9 5
LED10 4
LED11 3
LED12 2
Program
#define delay50 100
int sw1 = A4;
int sw2 = A5;
int myled[] = {2, 3, 4, 5, 6, 7, 8, 9,10,11,12,13};
int num_of_leds;
void setup() {
num_of_leds = sizeof(myled) / sizeof(int);
for (int i = 0; i < num_of_leds; i++) {
pinMode(myled[i], OUTPUT);
pinMode(sw1, INPUT);
pinMode(sw2, INPUT);

}
}
void loop() {
if((digitalRead(sw1)==LOW)&(digitalRead(sw2)==LOW))
{
ledonn();
 delay(1000);
ledoff();
delay(1000);
}
else if((digitalRead(sw1)==LOW)&(digitalRead(sw2)==HIGH))
{
pattern1();
}
else if((digitalRead(sw1)==HIGH)&(digitalRead(sw2)==LOW))
{
pattern2();
}
else if((digitalRead(sw1)==HIGH)&(digitalRead(sw2)==HIGH))
{
pattern3();
}
}
//TURN ON ALL LEDs
void ledonn() {
for (int i = 0; i < num_of_leds; i++) {
digitalWrite(myled[i], HIGH);
}
}
//TURN OFF ALL LEDs
void ledoff() {
for (int i = 0; i < num_of_leds; i++) {
digitalWrite(myled[i], LOW);
}
}
//LEFT TO RIGHT
void pattern1() {
for (int i = 0; i < num_of_leds; i++) {
digitalWrite(myled[i], HIGH);
delay(delay50);
digitalWrite(myled[i], LOW);
}
}
//RIGHT TO LEFT
void pattern2() {
for (int i = num_of_leds; i > 0; i--) {
digitalWrite(myled[i - 1], HIGH);
delay(delay50);
digitalWrite(myled[i - 1], LOW);
}
}
//ALTERNATE LEDs
void pattern3() {
for (int i = 0; i < num_of_leds; i = i + 2) {
digitalWrite(myled[i], HIGH);
digitalWrite(myled[i + 1], LOW);
}
delay(delay50);
for (int i = 0; i < num_of_leds; i = i + 2) {
digitalWrite(myled[i], LOW);
digitalWrite(myled[i + 1], HIGH);
}
delay(delay50);
}
Exp:9 To implement LED Pattern with Push Button Control With Arduino
Connection Details For LED and Push Button Switch
LED’S & SWITCH Arduino Uno
LED1 13
LED2 12
LED3 11
LED4 10
LED5 9
LED6 8
LED7 7
LED8 6
LED9 5
LED10 4
LED11 3
LED12 2
SW1 A4
SW2 A5

Program:
#define delay50 100
int sw1 = A4;
int sw2 = A5;
int myled[] = {2, 3, 4, 5, 6, 7, 8, 9,10,11,12,13};
int num_of_leds;
void setup() {
num_of_leds = sizeof(myled) / sizeof(int);
for (int i = 0; i < num_of_leds; i++) {
pinMode(myled[i], OUTPUT);
pinMode(sw1, INPUT);
pinMode(sw2, INPUT);
}
}
void loop() {
if((digitalRead(sw1)==LOW)&(digitalRead(sw2)==LOW))
{
ledonn();
 delay(1000);
ledoff();
delay(1000);
}
else if((digitalRead(sw1)==LOW)&(digitalRead(sw2)==HIGH))
{
pattern1();
}
else if((digitalRead(sw1)==HIGH)&(digitalRead(sw2)==LOW))
{
pattern2();
}
else if((digitalRead(sw1)==HIGH)&(digitalRead(sw2)==HIGH))
{
pattern3();
}
}
//TURN ON ALL LEDs
void ledonn() {
for (int i = 0; i < num_of_leds; i++) {
digitalWrite(myled[i], HIGH);
}
}
//TURN OFF ALL LEDs
void ledoff() {
for (int i = 0; i < num_of_leds; i++) {
digitalWrite(myled[i], LOW);
}
}
//LEFT TO RIGHT
void pattern1() {
for (int i = 0; i < num_of_leds; i++) {
digitalWrite(myled[i], HIGH);
delay(delay50);
digitalWrite(myled[i], LOW);
}
}
//RIGHT TO LEFT
void pattern2() {
for (int i = num_of_leds; i > 0; i--) {
digitalWrite(myled[i - 1], HIGH);
delay(delay50);
digitalWrite(myled[i - 1], LOW);
}
}
//ALTERNATE LEDs
void pattern3() {
for (int i = 0; i < num_of_leds; i = i + 2) {
digitalWrite(myled[i], HIGH);
digitalWrite(myled[i + 1], LOW);
}
delay(delay50);
for (int i = 0; i < num_of_leds; i = i + 2) {
digitalWrite(myled[i], LOW);
digitalWrite(myled[i + 1], HIGH);
}
delay(delay50);
}
 Exp:10 To display “Hello World “ in LCD 16X2 Display With Arduino
Connection Details For 16X2 LCD
16X2 LCD Arduino Uno
RS(Register Select) 7
EN(Enable) 6
D4 Dataline4 5
D5 Dataline5 4
D6 Dataline6 3
D7 Dataline7 2

Program:
#include <LiquidCrystal.h>
LiquidCrystal lcd (7, 6, 5, 4, 3, 2); // Define LCD Pin Connection 7 ~ RS , 6 ~ EN, 5 ~ D4,
4~ D5, 3 ~ D6, 2 ~ D7
void setup()
{
lcd.begin(16,2); //Configure LCD as 16x2
}
void loop()
{
lcd.setCursor(1,0);
lcd.print("Hello World");
}
Exp:11 To implement the Servo Motor Control with Arduino

Connection Details For Servo Motor

Servo Motor Arduino Uno
Servo Motor (Yellow) 5
Servo Motor (Brown) Ground
Servo Motor (RED) +5V

Program:
#include<Servo.h>
Servo Myservo;
int pos;
void setup()
{
Myservo.attach(5);
}

void loop()
{
for(pos=0;pos<=180;pos++)
{
Myservo.write(pos);
delay(15);
}
delay(1000);
for(pos=180;pos>=0;pos--)
{
Myservo.write(pos);
delay(15);
}
delay(1000);
}
Exp:12 To implement and monitor the LM35 Temperature Sensor and
Ultrasonic Distance Measurement With Arduino

a) LM35 Temperature Sensor.

Connection Details For LM35
LM35 Arduino Uno
1 +5V
2 A0
3 GND
Program:
void setup()
{
Serial.begin(9600);
}
void loop()
{
float vout =analogRead(A0); // Analog O/P Read
vout = (vout * 500)/1023; // Celsius Conversion Calculation
Serial.print("Room Temperature:");
Serial.print(vout);
Serial.println("In Celsius");
delay(1000);
}
b) Ultrasonic Sensor.
Connection Details For Ultrasonic Sensor
Ultrasonic Sensor Arduino Uno
Vcc +5V
Trig A1
Echo A2
Gnd Gnd
Program:

#include <NewPing.h>
#define TRIGGER_PIN A1
#define ECHO_PIN A2
#define MAX_DISTANCE 250
boolean goesForward = false;
NewPing sonar(TRIGGER_PIN, ECHO_PIN, MAX_DISTANCE);
void setup()
{ Serial.begin(9600);
}
void loop()
{
delay(1000);
Serial.print("Ping: ");
Serial.print(sonar.ping_cm());
Serial.println("cm");
}
int readPing()
{
delay(70);
int cm = sonar.ping_cm();
if (cm==0){ cm=250; }
return cm; }
Exp:13 To implement the IR Sensor Analog Input With Arduino

Connection Details For IR Sensor

IR Sensor Arduino Uno
IR Analog Output A3
GND GND
VCC +5V

Program:
void setup()
{
Serial.begin(9600);
}

void loop()
{
float vout =analogRead(A3); // Analog O/P Read
vout = (5*(vout/1023));
Serial.print(vout);
Serial.println("Volt");
delay(1000);
}
Exp:14 Using ThinkSpeak Cloud Reading Temperature Sensor Monitoring
with NodeMCU.
LM35 Temperature Sensor.
Connection Details For LM35
LM35 Arduino Uno
1 +5V
2 Node MCU A0
3 GND
Program:
#include <ESP8266WiFi.h>
String apiKey = "74085BCYRZG0G9YJ"; // Enter your Write API key from ThingSpeak
const char *ssid = "IElec Systems"; // replace with your wifi ssid and wpa2 key
const char *pass = "9840838264"; //Wifi Password
const char* server = "api.thingspeak.com";
WiFiClient client;
void setup()
{
Serial.begin(115200);
delay(10);
Serial.println("Connecting to ");
Serial.println(ssid);
WiFi.begin(ssid, pass);
while (WiFi.status() != WL_CONNECTED)
{
delay(500);
Serial.print(".");
}
Serial.println("");
Serial.println("WiFi connected");
}
void loop()
{
 float vout = analogRead(A0);
vout = (vout/1023)*3300;
vout = vout/10;
Serial.print(vout);
if (client.connect(server,80)) // "184.106.153.149" or api.thingspeak.com
{ String postStr = apiKey;
postStr +="&field1=";
postStr += String(vout);
postStr += "\r\n";

client.print("POST /update HTTP/1.1\n");

client.print("Host: api.thingspeak.com\n");
client.print("Connection: close\n");
client.print("X-THINGSPEAKAPIKEY: "+apiKey+"\n");
client.print("Content-Type: application/x-www-form-urlencoded\n");
client.print("Content-Length: ");
client.print(postStr.length());
client.print("\n\n");
client.print(postStr);

Serial.print("Temperature: ");
Serial.print(vout);
Serial.println("Send to Thingspeak.");
}
client.stop();
Serial.println("Waiting...");
delay(1000);// thingspeak needs minimum 15 sec delay between updates
}