Data sheet for SINAMICS G120C

Ordering data
6SL3210-1KE22-6AP1
Figure similar

Client order no. : Item no. :

Order no. : Consignment no. :
Offer no. : Project :
Remarks :

Rated data General tech. specifications

Input Power factor λ 0.70 ... 0.85

Number of phases 3 AC Offset factor cos φ 0.95

Line voltage 380 ... 480 V +10 % -20 % Efficiency η 0.97

Line frequency 47 ... 63 Hz Sound pressure level (1m) 66 dB

Rated current (LO) 33.00 A Power loss 0.35 kW

Rated current (HO) 26.00 A Ambient conditions

Output
Cooling Air cooling using an integrated fan
Number of phases 3 AC

Rated voltage 400 V Cooling air requirement 0.018 m³/s

Rated power (LO) 11.00 kW Installation altitude 1000 m

Rated power (HO) 7.50 kW Ambient temperature

Rated current (IN) 26.00 A Operation -10 ... 40 °C (14 ... 104 °F)

Rated current (LO) 25.00 A Transport -40 ... 70 °C (-40 ... 158 °F)

Rated current (HO) 16.50 A Storage -40 ... 70 °C (-40 ... 158 °F)

Max. output current 33.00 A Relative humidity

Pulse frequency 4 kHz 95 % At 40 °C (104 °F), condensation

Max. operation and icing not permissible
Output frequency for vector control 0 ... 240 Hz

Output frequency for V/f control 0 ... 550 Hz Closed-loop control techniques
V/f linear / square-law / parameterizable Yes

V/f with flux current control (FCC) Yes

V/f ECO linear / square-law Yes

Overload capability
Sensorless vector control Yes
Low Overload (LO)
Vector control, with sensor No
150 % base load current IL for 3 s, followed by 110 % base load current IL for 57 s in a
300 s cycle time
Encoderless torque control No

High Overload (HO) Torque control, with encoder No

200 % base load current IH for 3 s, followed by 150 % base load current IH for 57 s in a
300 s cycle time Communication
Communication PROFIBUS DP

Technical data are subject to change! There may be discrepancies between calculated and rating plate values.
Generated Fri Jul 22 08:08:25 CEST 2016
Page 1 of 2
Data sheet for SINAMICS G120C

Ordering data
6SL3210-1KE22-6AP1
Figure similar

Mechanical data Connections

Degree of protection IP20 / UL open type Signal cable

Size FSC Conductor cross-section 0.15 ... 1.50 mm² (28 ... 16 AWG)

Net weight 4.40 kg Line side

Width 140.0 mm Version Plug-in screw-type terminals

Height 295.0 mm Conductor cross-section 6.00 ... 16.00 mm² (10 ... 5 AWG)

Depth 203.0 mm Motor end

Inputs / outputs Version Plug-in screw terminals

Standard digital inputs Conductor cross-section 6.00 ... 16.00 mm² (10 ... 5 AWG)

Number 6 DC link (for braking resistor)

Switching level: 0→1 11 V Version Plug-in screw terminals

Switching level: 1→0 5V Conductor cross-section 6.00 ... 16.00 mm² (10 ... 5 AWG)

Max. inrush current 15 mA PE connection On housing with M4 screw

Fail-safe digital inputs Max. motor cable length

Number 1 Shielded 50 m

Digital outputs Unshielded 100 m

Number as relay changeover contact 1

Converter losses to EN 50598-2*
Output (resistive load) DC 30 V, 1 A
Efficiency class
IE2
Number as transistor 1
Comparison with the reference converter (90% / -66.85 %
100%)
Output (resistive load) DC 30 V, 1 A

Analog / digital inputs

I
227.0 W (1.31 %) 261.0 W (1.50 %) 311.0 W (1.80 %)
Number 1 (Differential input) 100%

Analog outputs

Number 1 (Non-isolated output) 152.0 W (0.88 %) 165.0 W (0.95 %) 183.0 W (1.06 %)

50%

PTC/ KTY interface

126.0 W (0.73 %) 132 W (0.76 %)
25%
1 motor temperature sensor input, sensors that can be connected: PTC, KTY
and Thermo-Click, accuracy ±5 °C

50% 90% f
Standards
The percentage values show the losses in relation to the rated apparent power of the converter.
Compliance with standards UL, cUL, CE, C-Tick (RCM)

The diagram shows the losses for the points (as per standard EN 50598) of the relative torque
EMC Directive 2004/108/EC, Low-Voltage
CE marking generating current (I) over the relative motor stator frequency(f). The values are valid for the basic
Directive 2006/95/EC version of the converter without options/components.

*calculated values; increased by 10% according to the standard

Technical data are subject to change! There may be discrepancies between calculated and rating plate values.
Generated Fri Jul 22 08:08:25 CEST 2016
Page 2 of 2