Name of project :-Fatehpur-Laxmangarh Water Supply Project Under JJM

Dist.- Sikar, Pakage -2

Name of work:- Design of Village Transfer Chamber room
Design Calculation
Size of Room :-

Length of room = 2.200 m

Width of room = 1.200 m
Height room = 2.500 m
Thickness of wall = 0.230 m
Thickness of plaster = 0.020 m

0.23 m 2.2 m 0.23 m

0.23 m

2.2 m

1.2 m
1.2 m

0.23 m

Design Data Assumption:-

Thickness of Roof slab = 0.100 m

Height of plinth above Ground level = 0.30 m
Unit weight of brick masonry = 20 KN/Cum
Unit weight of RCC = 25 KN/Cum
Unit weight of CC = 24 KN/Cum
Unit weight of soil = 18 KN/Cum
Angle or repose = 30 Degree
Design Criteria as per SP 20: 1991
Soil bearing Capacity = 70 KN/Sqm

Depth of Foundation
 𝐷=𝑃/𝛾 ((1−sin⁡𝜙)/(1+sin⁡𝜙 ))^2 D = 0.86 m
Provided
depth = 0.9 m

Load Calculation
Parapet (0.23+0.02) x0x20 = 0 KN/m
Roof Load
RCC slab 0.1 mm thick 0.1x25 = 2.5 KN/Sqm
Floor finish load on terrace = 1 KN/Sqm
Live load as per IS 875 Part-II = 0.75 KN/Sqm
Total load = 4.25 KN/Sqm
Clear span of slab = 1.20 m
Effective span = 1.43 m

Roof load on wall 4.25x1.43x1.43/(4x1.43) = 1.52 KN/m

Thickness of wall including plaster 0.23+0.02 = 0.250 m
Self-load of wall up to plinth level 0.25x2.5x20 = 12.5 KN/m
Design of wall
Short wall
Length = 1.2 m
‘This portion bears additional load on account of opening on one side, which is 0.9 m in width.

Total load on wall (1.519 + 12.5 + 0) x (1.2+ 1/2) 23.83 KN

Since wall is plastered on both sides, it may be assumed to have raked joints on both sides.

Thus, effective
thickness = 0.210 m
Compressive stress at plinth level W/A = 0.079 N/Sqmm

Slenderness ratio from consideration of height (h/t)

SR= (0.3+2.5+0.1)/0.21 = 10.179
Slenderness ratio from consideration of height =

Through length of wall ‘a’ is less than 4 t that is, 92 cm, it will not be considered as a column,
because it is supported by a cross wall on one side.

m (Because opening is
Effective length l 2L = 2.4 less than 0.5H)
Therefore, SR in the direction of length = 11.43
Since length wise SR is less than that in the direction of
height.

Stress reduction factor k, for SR 7.0 (from Table 9 of

the IS Code 1987) 1.00
=
Area reduction factor k, (see
5.4.1.2) 0.7+1.5A = 1.08
Therefore, basic compressive stress of required masonry, with unity Shape modification factor

0.26/ = 0.28 N/Sqmm

 (0.93*.86)
Long
wall
Length = 2.2 m
‘This portion bears additional load on account of opening on one side, which is 1.0 m in width.
Total load on wall (1.52 + 12.5 + 0) x (2.2+ 1/2 ) 37.85 KN
Thus, effective
thickness = 0.210
Compressive stress at plinth level W/A = 0.126 N/Sqmm
Slenderness ratio from consideration of height (h/t) =
10.178
SR= (0.3+2.5+0.1)/0.21 = 57
Slenderness ratio from consideration of height =
though length of wall ‘b’ is less than 4 t that is, 92 cm, it will not be considered as a column,
because it is supported by a cross wall on one side.
(see Table 5 of the
Effective length l 2L = 4.4 m Code)
Therefore, SR in the direction of length = 20.95
Since Length wise f SR is less than that in the direction o height, former will govern the design.
Stress reduction factor k, for SR 7.0 (from Table 9 of
0.81
the IS Code 1987) =
Area reduction factor k, (see
5.4.1.2) 0.7+1.5A = 1.39
Therefore, basic compressive stress of required masonry, with unity Shape modification factor
0.26/
(0.93*0.83) = 0.20 N/Sqmm

Thus, from Table 8 we get grade of mortar for the masonry to be M2 (1:6)
Cement sand as per Table 1 IS Code 1987 it is having Compressive strength 3.0
N/mm2 after 28 days
Design of Foundation

Load on plinth level per meter length = 14.02 KN/m

Load of DPC 0.075x0.45x24 = 0.81 KN/m
Load of first offset 0.45x0.75x20 = 6.75 KN/m
Load of Second offset 0.60x0.45x20 = 5.4 KN/m
Total load transferred on
soil = 26.98 KN/Sqm
Soil bearing capacity as per SBC Report = 70 KN/Sqm
= Safe
Required width of Foundation per meter = 0.39 m
Provide width of Foundation per meter = 0.60 m
= Safe
 Design of Simply supported slab

Given data:
Shorter span (clear dimension) = 2200 mm
Longer span (clear dimension) = 1200 mm
Live load = 0.75 KN/m2
Width of wall = 230 mm
Fire resistance = 2 hours
Grade of concrete (fck) = 20 N/mm2
Grade of steel (fy) = 500 N/mm2
Load factor = 1.5
Xumax/d = 0.456
Mu limit (Qu) = 2.655
2
bd
Solution:
1.Thickness of slab:
Assume modification factor = 1.5 (% of steel is 0.2%)
Span/depth = 20
Span/depth = 30 ~ 30
Clear cover = 25 mm
Required effective depth = 73.3333 ~ 102 mm
Adopt thickness of slab is = 100 mm
Effective depth of slab (d) = 71.0 mm
2.Effective span:
Least of followig
C/C of support = 2430.0 mm
Clear span + d = 2271.0 mm
For effective span (lx) = 2271.0 mm
3.Load calculation:
Self weight of slab = 2.5 KN/m2
Floor finish = 1.0 KN/m2
Partition load = 0.0 KN/m2
Sunken filling = 0.0 KN/m2
Live load = 0.75 KN/m2
Total load = 4.25 KN/m2
Total design load (W)/m = 6.375 KN/m
4.Design moments:
Bending moment at mid span = 4.10984 KN.m
d required = √Mu/Quxb = 39.3477 mm
The slab depth is enough
5.Reinforcements:
Minimum area of steel (Astmin) = 0.12 %
mm
= 120.00 2

0.5 x
fck 4.6 x Mu
Area of steel (Ast) = (1 fck x 1000 x d2 )1000 x
fy - √1- d

mm
= 140.04 2

Us
8 mmØ
e
Required spacing = 213.00 ~ 200 mm
Area of steel mm
= 251.20 2
(Provided)
Provide 8 mmØ @ 200 mm c/c
Distribution of steel:
mm
Area of steel = 120.00 2

Us
8 mmØ
e
Required spacing = 213.00 ~ 200 mm
Provide 8 mmØ @ 200 mm c/c

6.Check for deflection:

% of steel at mid span = 0.354 %
fs value = 161.7
Modification factor = 2.000 (Ref Fig 4 IS 456-2000)
71.
Required effective depth = 56.78 < 0 mm
The slab depth is enough

7.Check for shear:

Maximum shear force at support = 7.23881 KN
Nominal shear stress (‫ﺡ‬v) = 0.10196 N/mm2
Permissible shear stress (‫ح‬c) 0.41589 N/mm2
The slab depth is enough

8.Check for crack width:

a
=
Level at which crack width is to be calculated (a') 71 mm '

Modulas of elasticity of steel (Es) = 200000 N/mm2

Long term modulas of elasticity of concrete (Ec) = 11180 N/mm2
Modular ratio (m) = 18
% of steel at mid span = 0.354 %
Neutral axis depth factor (k) = 0.298
Neutral axis depth (Xu) = 21.168 mm
mm
=
Area of steel provided (Ast) 251.20 2
 mm
= 4
Cracked moment of inertia (Icr) 14320322.09
Service load moment (M) = 2.740 KN.m/m
Service stress in steel (fst) = 170.56 N/mm2
Strain in concrete at the bottom face (ε1) = 0.0013
Mean tensile strain in concrete (εm) = 0.0008 > 0
The slab is cracked section

Distance of point from surface of bar (acr) = 104.120 mm

Crack width (wcr) = 0.086 mm < 0.2 mm
The slab depth is enough

9.Results:
Size of slab is 2200 x 1200 mm
Thickness of slab is 100 mm
Provide 8 mmØ @ 200 mm c/c (main bars)
Provide 8 mmØ @ 200 mm c/c (Distribution)

8 mmØ @ 200 mm c/c

176

8 mmØ @ 200 mm c/c

2200

96

96
176

1200
Slab thickness is 100 mm
All dimensions are in mm

Design of Simply supported slab

Given data:
Shorter span (clear dimension) = 1400 mm
Longer span (clear dimension) = 1200 mm
Live load = 0.75 KN/m2
 Width of wall = 230 mm
Fire resistance = 2 hours
Grade of concrete (fck) = 20 N/mm2
Grade of steel (fy) = 500 N/mm2
Load factor = 1.5
Xumax/d = 0.456
Mu limit (Qu) = 2.655
bd2
Solution:
1.Thickness of slab:
Assume modification factor = 1.5 (% of steel is 0.2%)
Span/depth = 20
Span/depth = 30 ~ 30
Clear cover = 25 mm
Required effective depth = 46.6667 ~ 75.7 mm
Adopt thickness of slab is = 100 mm
Effective depth of slab (d) = 71.0 mm
2.Effective span:
Least of following
C/C of support = 1630.0 mm
Clear span + d = 1471.0 mm
For effective span (lx) = 1471.0 mm
3.Load calculation:
Self-weight of slab = 2.5 KN/m2
Floor finish = 1.0 KN/m2
Partition load = 0.0 KN/m2
Sunken filling = 0.0 KN/m2
Live load = 0.75 KN/m2
Total load = 4.25 KN/m2
Total design load (W)/m = 6.375 KN/m
4.Design moments:
Bending moment at mid span = 1.72431 KN.m
d required = √Mu/Quxb = 25.4868 mm
The slab depth is enough
5.Reinforcements:
Minimum area of steel (Astmin) = 0.12 %
= 120.00 mm2

0.5 x fck 4.6 x Mu

Area of steel (Ast) = (1 fck x 1000 x d2 )1000 x
fy - √1- d
 = 120.00 mm2
Use 8 mmØ
Required spacing = 213.00 ~ 200 mm
Area of steel
= 251.20 mm2
(Provided)
Provide 8 mmØ @ 200 mm c/c
Distribution of steel:
Area of steel = 120.00 mm2
Use 8 mmØ
Required spacing = 213.00 ~ 200 mm
Provide 8 mmØ @ 200 mm c/c

6.Check for deflection:

% of steel at mid span = 0.354 %
fs value = 138.5
Modification factor = 2.000 (Ref Fig 4 IS 456-2000)
Required effective depth = 36.78 < 71.0 mm
The slab depth is enough

7.Check for shear:

Maximum shear force at support = 4.68881 KN
Nominal shear stress (‫ﺡ‬v) = 0.06604 N/mm2
Permissible shear stress (‫ح‬c) 0.41589 N/mm2
The slab depth is enough

8.Check for crack width:

a
=
Level at which crack width is to be calculated (a') 71 mm '
modules of elasticity of steel (Es) = 200000 N/mm2
Long term modulus of elasticity of concrete (Ec) = 11180 N/mm2
Modular ratio (m) = 18
% of steel at mid span = 0.354 %
Neutral axis depth factor (k) = 0.298
Neutral axis depth (Xu) = 21.168 mm
Area of steel provided (Ast) = 251.20 mm2
Cracked moment of inertia (Icr) = 14320322.09 mm4
Service load moment (M) = 1.150 KN.m/m
Service stress in steel (fst) = 71.56 N/mm2
Strain in concrete at the bottom face (ε1) = 0.0006
Mean tensile strain in concrete (εm) = 0.0000 > 0
The slab is cracked section

Distance of point from surface of bar (acr) = 104.120 mm

Crack width (wcr) = 0.004 mm < 0.2 mm
The slab depth is enough
9.Results:
Size of slab is 1400 x 1200 mm
Thickness of slab is 100 mm
Provide 8 mmØ @ 200 mm c/c (main bars)
Provide 8 mmØ @ 200 mm c/c (Distribution)

DESIGN CALCULATION
DESIGN DATA

CHAMBER DATA
Clear width of chamber = 1.20 m
Clear Lenght of chamber = 2.20 m
Number of panles in Length = 1.00 Nos
Length of pannel between wall in Long direction = 2.20 m
Number of panles in width = 1.00 Nos
Length of pannel between wall in short direction = 1.20 m
L/H in long direction = 1.07 m
L/H in short direction = 0.59
Depth of tank below GL (a) = 1.45 m
Height of wall top above GL = 0.60 m
Thickness of wall at top = 0.15 m
Thickness of wall at bottom = 0.15 m
Average thickness of wall = 0.15 m
Thickness of wall at edges = 0.15 m
Distance of taper from edge of wall = 0.00 m
SBC for design (as per given data 10.0t/sqm at 5.25m depth) = 70.00 KN/m²
Live load on roof of tank = 3.00 KN/m²
 Design Constants

Grade of concrete =M 30.00

Grade of steel =Fe 500.00 N/mm2
Permissible stress in steel ( As per Table No. 22, IS 456:2000) σ st = 230.00 N/mm2
Permissible stress in steel ( As per Table No. 4, IS 3370 Part II) σ st = 130.00 N/mm2
Compressive stress of concrete Fck = 30.00 N/mm2
Permissible compressive stress in concrete in Bending ( As per Table No. 2, IS 3370 Part II) σ cbc = 10.00 N/mm2
Permissible compressive stress in concrete in Direct ( As per Table No. 2, IS 3370 Part II) σ cc = 8.00 N/mm2
Permissible Concrete Stresses in Resistance to Cracking in direct tension ( As per Table No. σ ct = 1.50 N/mm2
1, IS 3370
Part II)
Permissible Concrete Stresses in Resistance to Cracking in bending ( As per Table No. 1, IS σ cbt = 2.00 N/mm2
3370 Part II)
 Calculation of factors

i) Factors in uncracked section m 9.33

k 0.289
j 0.904
Q 1.304

i) Factors in uncracked section m 9.33

k 0.126
j 0.958
Q 0.120
Density of soil = 18.00 KN/m³
Angle of internal friction (φ) = 30.00 °
Active earth pressure coefficient = 0.33
Earth pressure coefficient in rest condition = 0.50
Density of concrete 25.0 KN/m³
Density of water = 9.81 KN/M³
Surcharge Load of surcharge if any vehicle crossing near tank as per IRC 6 clause 214.1.1.3 = 7.20 KN/M²
Soil Properties adopted in the design:-
Settlement = 50.00 MM
K (Factor of safety = 2.5) = 3500
Spacing B/w Nodes = 0.45
K Value for node = 787.50
Load Calculation
Dead Load
Assume thickness of top slab = 0.10 m
self-weight of Slab = 2.50 KN/M²
Floor Finish Load = 1.50 KN/M²
Total load = 4.00 KN/M²
L/B ratio = 1.83
Slab design as one way Slab so Slab load Transfer only long wall
Dead Load on Per Meter Length = 5.28 KN/m
Live Load
Live Load on Top Slab = 3.00 KN/M²
Slab design as one way Slab so Slab load Transfer only long wall
Dead Load on Per Meter Length 3.96 KN/m
Earth pressure on Wall
Earth Pressure at Top of wall = 0.00 KN/m
Earth Pressure at Bottom of wall at rest condition = 13.06 KN/m
Surcharge Load of surcharge if any vehicle crossing near tank as per IRC 6 clause 214.1.1.3 = 7.20 KN/m
Water pressure on Wall
Water Pressure at Top of wall = 0.00 KN/m
water Pressure at Bottom of wall = 0.00 KN/m
DESIGN OF OUTER LONG WALL "A & B" :
Clear cover, Cmin = 50 Es = 200000
Grade of concrete = 30 b = 1000
Grade of steel = 500 σcbt = 2
Ast, required = (1-SQRT(1-((4.6*Mu)/(fck*b*d^2))))/((2/(b*d))*(fy/fck))
Design Forces Strength Criteria
Plate 42 40 54 52 52
9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5
L/C Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5
Live Live Live Live Live

SQX N/mm2 0 -0.006 0.001 -0.001 -0.001

SQY N/mm2 0.001 -0.001 0 -0.006 -0.006
MX kNm/m 0.07 -0.15 0.005 -0.038 -0.038
MY kNm/m 0.005 -0.038 0.07 -0.15 -0.15
MXY kNm/m -0.021 -0.068 -0.021 -0.068 -0.068
SX N/mm2 -0.089 -0.144 0.001 0.001 0.001
SY N/mm2 0.001 0.001 -0.089 -0.144 -0.144
SXY N/mm2 0.013 -0.064 0.013 -0.064 -0.064

MuX Tension in X D/d

(IN HORIZONTAL DIRECTION) Ast, Ast,
required provided
0.091 0 150 2.379 8 200 251.4285714
WATER FACE 88 0 200
0.218 0 150 5.704 8 200 251.4285714
EARTHFACE 88 0 200

Face pt Zone depth pt,min Check

WATER FACE 0.286 75 180 OK
EARTHFACE 0.286 75 180 OK
(IN VERTICAL DIRECTION)
Muy Tension in Y D/d Ast, Ast,
required provided
0.091 0 150 2.181 8 200 251.4285714
EARTHFACE 96 0 200
0.218 0 150 5.228 8 200 251.4285714
WATER FACE 96 0 200
Face pt Zone depth pt,min Check
EARTHFACE 0.262 75 180 OK
WATER FACE 0.262 75 180 OK
SERVICEABILITY
Plate 42 40 54 52 40
L/C 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2
Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2
Live Live Live Live Live
SQX N/mm2 0 -0.005 0.001 -0.001 -0.005
SQY N/mm2 0.001 -0.001 0 -0.005 -0.001
MX kNm/m 0.056 -0.12 0.004 -0.03 -0.12
MY kNm/m 0.004 -0.03 0.056 -0.12 -0.03
MXY kNm/m -0.017 -0.055 -0.017 -0.055 -0.055
SX N/mm2 -0.071 -0.115 0.001 0.001 -0.115
SY N/mm2 0.001 0.001 -0.071 -0.115 0.001
SXY N/mm2 0.01 -0.051 0.01 -0.051 -0.051
Limit state of serviceability (REF. APPENDIX F OF IS 3370))
Clear cover, Cmin = 50 σst = Ms/(Ast*(d-n/3))
Grade of concrete = 30 ε2 = ε1 =(fs/Es)x(h-x)/(d-x)
1.5*b*(h-x)*(a-x)/{3*
Grade of steel = 500 CRACK WIDTH = 3*acr*ξm/[1+(2*{(acr-cmin)/(h-x)}]
Es = 200000 x = αeρ*(sqrt(1+(2/(αeρ)))-1)*d
αe = 14.60593487 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)
Allowable crack width = 0.2
Plate Tension Face Depth of d T (FROM Mapplied
sec STA
42 WATER FACE 150 88 0 0.073 For MX & SX
40 EARTHFACE 150 88 0 0.175
54 WATER FACE 150 96 0 0.073 For MY & SY
52 EARTHFACE 150 96 0 0.175

Plate Bar Dia Spacing Ast

8 200
42 251.20
0 200
8 200
40 251.2
0 200
8 200
54 251.2
0 200
8 200
52 251.2
0 200
 ξ1 =(fs/Es)x(D-n)/(d-n) ξ2 = b*(D-n)*(a-n)/{3*Es*As*(d-n)}

ξm = ξ1 -ξ2 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)

Wcr = 3*acr*ξm/[1+(2*{(acr-cmin)/(D-n)}]

x ρt fst ξ1 ξ2 ξm acr Wcr Check

22.00603 0.00285 3.60263 0.000035 0.001647 -0.001612 117.648581 -0.276601 OK

22.00603 0.00285 8.63645 0.000084 0.001647 -0.001563 117.648581 -0.268226 OK

23.12486 0.00262 3.29142 0.0000287 0.001466 -0.001437 109.648581 -0.243607 OK

23.12486 0.00262 7.89039 0.000069 0.001466 -0.001397 109.648581 -0.236820 OK

DESIGN OF SHORT LONG WALL "C" :
Clear cover, Cmin = 50 Es = 200000
Grade of concrete = 30 b= 1000
Grade of steel = 500 σcbt = 2
Ast, required = (1-SQRT(1-((4.6*Mu)/(fck*b*d^2))))/((2/(b*d))*(fy/fck))
Design Forces Strength Criteria
Plate 36 55 36 55 56
9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5
Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5
L/C Live Live Live Live Live

SQX N/mm2 0.018 0.003 0.018 0.003 0.003

SQY N/mm2 -0.009 0.001 -0.009 0.001 -0.001
MX kNm/m 0.578 -0.018 0.578 -0.018 -0.018
MY kNm/m 0.162 0.035 0.162 0.035 0.035
MXY kNm/m -0.015 -0.037 -0.015 -0.037 0.037
SX N/mm2 -0.076 -0.035 -0.076 -0.035 -0.035
SY N/mm2 -0.02 0 -0.02 0 0
SXY N/mm2 -0.004 0.009 -0.004 0.009 -0.009

MuX Tension in X D/d

(IN HORIZONTAL DIRECTION) Ast, Ast,
required provided
0.593 0 150 15.545 8 200 251.4285714
WATER FACE 88 0 200
0.055 0 150 1.438 8 200 251.4285714
EARTHFACE 88 0 200

Face pt Zone depth pt,min Check

WATER FACE 0.286 75 180 OK
EARTHFACE 0.286 75 180 OK
(IN VERTICAL DIRECTION)
Muy Tension in Y D/d Ast, Ast,
required provided
0.177 0 150 4.244 8 200 251.4285714
EARTHFACE 96 0 200
0.072 0 150 1.726 8 200 251.4285714
WATER FACE 96 0 200
Face pt Zone depth pt,min Check
EARTHFACE 0.262 75 180 OK
WATER FACE 0.262 75 180 OK
SERVICEABILITY
Plate 36 55 36 55 56
10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2
L/C Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2
Live Live Live Live Live
SQX N/mm2 0.015 0.002 0.015 0.002 0.002
SQY N/mm2 -0.007 0.001 -0.007 0.001 -0.001
MX kNm/m 0.463 -0.015 0.463 -0.015 -0.015
MY kNm/m 0.13 0.028 0.13 0.028 0.028
MXY kNm/m -0.012 -0.029 -0.012 -0.029 0.029
SX N/mm2 -0.061 -0.028 -0.061 -0.028 -0.028
SY N/mm2 -0.016 0 -0.016 0 0
SXY N/mm2 -0.003 0.007 -0.003 0.007 -0.007
Limit state of serviceability (REF. APPENDIX F OF IS 3370))
Clear cover, Cmin = 50 σst = Ms/(Ast*(d-n/3))
Grade of concrete = 30 ε2 = ε1 =(fs/Es)x(h-x)/(d-x)
1.5*b*(h-x)*(a-x)/{3*
Grade of steel = 500 CRACK WIDTH = 3*acr*ξm/[1+(2*{(acr-cmin)/(h-x)}]
Es = 200000 x = αeρ*(sqrt(1+(2/(αeρ)))-1)*d
αe = 14.60593487 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)
Allowable crack width = 0.2
Plate Tension Face Depth of d T (FROM Mapplied
sec STA
36 WATER FACE 150 88 0 0.475 For MX & SX
55 EARTHFACE 150 88 0 0.044
36 WATER FACE 150 96 0 0.142 For MY & SY
55 EARTHFACE 150 96 0 0.057

Plate Bar Dia Spacing Ast

8 200
36 251.20
0 200
8 200
55 251.2
0 200
8 200
36 251.2
0 200
8 200
55 251.2
0 200
ξ1 =(fs/Es)x(D-n)/(d-n) ξ2 = b*(D-n)*(a-n)/{3*Es*As*(d-n)}

ξm = ξ1 -ξ2 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)

Wcr = 3*acr*ξm/[1+(2*{(acr-cmin)/(D-n)}]

x ρt fst ξ1 ξ2 ξm acr Wcr Check

22.00603 0.00285 23.44179 0.000227 0.001647 -0.001420 117.648581 -0.243592 OK

22.00603 0.00285 2.17145 0.000021 0.001647 -0.001626 117.648581 -0.278982 OK

23.12486 0.00262 6.40249 0.0000557 0.001466 -0.001410 109.648581 -0.239016 OK

23.12486 0.00262 2.57001 0.000022 0.001466 -0.001443 109.648581 -0.244672 OK

DESIGN OF COMMON WALL "D" :
Clear cover, Cmin = 50 Es = 200000
Grade of concrete = 30 b= 1000
Grade of steel = 500 σcbt = 2
Ast, required = (1-SQRT(1-((4.6*Mu)/(fck*b*d^2))))/((2/(b*d))*(fy/fck))
Design Forces Strength Criteria
Plate 45 44 45 44 48
9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5
L/C Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5
Live Live Live Live Live

SQX N/mm2 -0.001 -0.001 -0.001 -0.001 -0.003

SQY N/mm2 0 0.001 0 0.001 0.003
MX kNm/m 0.142 0.046 0.142 0.046 0.081
MY kNm/m -0.147 -0.251 -0.147 -0.251 -0.15
MXY kNm/m -0.056 0.039 -0.056 0.039 -0.102
SX N/mm2 0.012 -0.003 0.012 -0.003 -0.056
SY N/mm2 -0.251 -0.249 -0.251 -0.249 -0.283
SXY N/mm2 0.002 -0.022 0.002 -0.022 -0.03

MuX Tension in X D/d

(IN HORIZONTAL DIRECTION) Ast, Ast, provided
required
0.198 2.76 250 5.884 8 300 167.6190476
WATER FACE 188 0 300
0.085 0 250 1.164 8 300 167.6190476
EARTH FACE 188 0 300

Face pt Zone depth pt,min Check

WATER FACE 0.1 115 138 OK
EARTH FACE 0.1 115 138 OK
(IN VERTICAL DIRECTION)
Muy Tension in Y D/d Ast, Ast, provided
required
0.203 0 250 2.654 8 300 167.6190476
EARTH FACE 196 0 300
0.29 0 250 3.791 8 300 167.6190476
WATER FACE 196 0 300
Face pt Zone depth pt,min Check
EARTH FACE 0.095 115 138 OK
WATER FACE 0.095 115 138 OK
SERVICEABILITY
Plate 45 44 45 44 48
10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2
L/C Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2
Live Live Live Live Live
SQX N/mm2 -0.001 -0.001 -0.001 -0.001 -0.003
SQY N/mm2 0 0.001 0 0.001 0.003
MX kNm/m 0.114 0.036 0.114 0.036 0.064
MY kNm/m -0.118 -0.201 -0.118 -0.201 -0.12
MXY kNm/m -0.045 0.031 -0.045 0.031 -0.082
SX N/mm2 0.01 -0.003 0.01 -0.003 -0.045
SY N/mm2 -0.201 -0.199 -0.201 -0.199 -0.227
SXY N/mm2 0.002 -0.018 0.002 -0.018 -0.024
Limit state of serviceability (REF. APPENDIX F OF IS 3370))
Clear cover, Cmin = 50 σst = Ms/(Ast*(d-n/3))
Grade of concrete = 30 ε2 = 1.5*b*(h-x)*(a-x)/{3* ε1 =(fs/Es)x(h-x)/(d-x)
Grade of steel = 500 CRACK WIDTH = 3*acr*ξm/[1+(2*{(acr-cmin)/(h-x)}]
Es = 200000 x = αeρ*(sqrt(1+(2/(αeρ)))-1)*d
αe = 14.60593487 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)
Allowable crack width = 0.2
Plate Tension Face Depth of d T (FROM Mapplied
sec STA
45 WATER FACE 230 168 2.3 0.159 For MX & SX
44 EARTH FACE 230 168 0 0.067
45 WATER FACE 230 176 0 0.163 For MY & SY
44 EARTH FACE 230 176 0 0.232

Plate Bar Dia Spacing Ast

8 300
45 167.47
0 300
8 300
44 167.466667
0 300
8 300
45 167.466667
0 300
8 300
44 167.466667
0 300
ξ1 =(fs/Es)x(D-n)/(d-n) ξ2 = b*(D-n)*(a-n)/{3*Es*As*(d-n)}

ξm = ξ1 -ξ2 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)

Wcr = 3*acr*ξm/[1+(2*{(acr-cmin)/(D-n)}]

x ρt fst ξ1 ξ2 ξm acr Wcr Check

26.32623 0.00100 5.96291 0.000043 0.002914 -0.002871 163.423963 -0.532762 OK

26.32623 0.00100 2.51267 0.000018 0.002914 -0.002896 163.423963 -0.537363 OK

26.99847 0.00095 5.82829 0.0000397 0.002753 -0.002713 155.423963 -0.620461 OK

26.99847 0.00095 8.29549 0.000057 0.002753 -0.002696 155.423963 -0.616617 OK

E) DESIGN OF FOOTING FOR WALL:
Clear cover, Cmin = 50 Es = 200000
Grade of concrete = 30 b= 1000
Grade of steel = 500 σcbt = 2
Ast, required = (1-SQRT(1-((4.6*Mu)/(fck*b*d^2))))/((2/(b*d))*(fy/fck))

Design Forces Strength Criteria

Plate 31 72 21 70 31
9 ULC, 1.5 Dead 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5 9 ULC, 1.5
L/C + 1.5 Live Dead + 1.5 Dead + 1.5 Dead + 1.5 Dead + 1.5
Live Live Live Live
SQX N/mm2 0.16 0.033 0.16 0.048 0.16
SQY N/mm2 -0.11 -0.006 0.11 0.014 -0.11
MX kNm/m 3.94 -4.101 3.94 -3.966 3.94
MY kNm/m 1.749 0.221 1.749 0.083 1.749
MXY kNm/m -0.174 0.148 0.174 -0.291 -0.174
SX N/mm2 0.013 0.016 0.013 0.012 0.013
SY N/mm2 0.056 -0.002 0.056 0.004 0.056
SXY N/mm2 -0.022 0.004 0.022 0.002 -0.022

MuX Tension in X D/d

(IN LONGER DIRECTION) Ast, required Ast, provided
4.114 1.95 150 112.05 8 200 251.4285714
Bottom 88 0 200
4.249 2.4 150 116.252 8 200 251.4285714
Top 88 0 200

Face pt Zone depth pt,min Check

Bottom 0.286 75 180 OK
Top 0.286 75 180 OK
(IN SHORTER DIRECTION)
Muy Tension in Y D/d Ast, required Ast, provided
1.923 12.6 150 60.929 8 200 251.4285714
96 0 200
0.374 0.9 150 10.009 8 200 251.4285714
96 0 200
Face pt Zone depth pt,min Check
0 0.262 75 180 OK
0 0.262 75 180 OK
SERVICEABILITY
Plate 31 72 21 70 31
L/C 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2 10 ULC, 1.2
Dead Dead + 1.2 Dead + 1.2 Dead + 1.2 Dead + 1.2
+ 1.2 Live
SQX N/mm2 0.128 0.027 0.128 0.038 0.128
SQY N/mm2 -0.088 -0.005 0.088 0.012 -0.088
MX kNm/m 3.152 -3.281 3.152 -3.173 3.152
MY kNm/m 1.399 0.176 1.399 0.067 1.399
MXY kNm/m -0.139 0.118 0.139 -0.233 -0.139
SX N/mm2 0.011 0.013 0.011 0.009 0.011
SY N/mm2 0.044 -0.002 0.044 0.003 0.044
SXY N/mm2 -0.018 0.003 0.018 0.001 -0.018
Limit state of serviceability (REF. APPENDIX F OF IS 3370))
Clear cover, Cmin 50 σst = Ms/(Ast*(d-n/3))
=
Grade of concrete 30 ε2 = 1.5*b*(h-x)*(a-x)/{3*Es ε1 =(fs/Es)x(h-x)/(d-x)
=
Grade of steel = 500 CRACK WIDTH = 3*acr*ξm/[1+(2*{(acr-cmin)/(h-x)}]
Es = 200000 x = αeρ*(sqrt(1+(2/(αeρ)))-1)*d
αe = 14.60593487 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)
Allowable crack width = 0.2
Plate Tension Face Depth of d T (FROM Mapplied
section STAA
31 150 88 1.65 3.291 For MX & SX
72 150 88 1.95 3.399
21 150 96 6.6 1.538 For MY & SY
70 150 96 0.45 0.3

Plate Bar Dia Spacing Ast

8 200
31 251.20
0 200
8 200
72 251.2
0 200
8 200
21 251.2
0 200
8 200
70 251.2
0 200

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 15

15:11
ξ1 =(fs/Es)x(D-n)/(d-n) ξ2 = b*(D-n)*(a-n)/{3*Es*As*(d-n)}

ξm = ξ1 -ξ2 acr = SQRT((R/2)^2+(Cmin+db/2)^2)-(db/2)

Wcr = 3*acr*ξm/[1+(2*{(acr-cmin)/(D-n)}]

x ρt fst ξ1 ξ2 ξm acr Wcr Check

22.00603 0.00285 162.41456 0.001575 0.001647 -0.000072 117.648581 -0.012361 OK

22.00603 0.00285 167.74448 0.001627 0.001647 -0.000020 117.648581 -0.003492 OK

23.12486 0.00262 69.34526 0.0006036 0.001466 -0.000862 109.648581 -0.146124 OK

23.12486 0.00262 13.52638 0.000118 0.001466 -0.001348 109.648581 -0.228502 OK

Job No Sheet No Rev

1
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 2 of 15

15:11
 By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Job Information

Engineer Checked Approved

Name:
Date:
Structure Type 11-May-24
SPACE FRAME

Project ID
Project Name

Number of Nodes 74 Highest Node 74

Number of Elements 8 Highest Beam 80
Included
Numberinofthis printout are data56
Plates for: Highest Plate 72
All The Whole Structure

Number of Basic Load Cases 4

Included in this printout are results for load cases:
Number of Combination Load Cases 4

Type L/C Name

Primary 1 DL
Primary 2 LL
Primary 7 EARTH_PRESSURE_AT_BASE
Primary 8 EARTH_PRESSURE_AT_WALL
Combination 9 ULC, 1.5 Dead + 1.5 Live
Combination 10 ULC, 1.2 Dead + 1.2 Live
Combination 11 ULC, 1.5 Dead
Combination 12 ULC, 0.9 Dead

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 3 of 15

15:11
 Job No Sheet No Rev
2
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

z
x z
z
x x
y
y
z
y x
z z
y x y
z
x
z z
z x y y xx
y y
z z
x x
y
x
z
y z yy
x z
x 2
z
z y2 x
z x yx 2

x z x
y 2 y
y 2 y 2
zz y
2 x x x z z
y 2
x y 2 x
y yx z x z
2
2 y x yx 2
z x 2 z
2 z x z y 2 yy x
2 x y 2y 2
z x y z x y 2
y 2
x z 2
z y 2 z
2 x z 2 yx
y z yx
2 2
z y
2 z z yx 2 x
2
z x
x z 2 y y y 2
y z x z x z
2 2 2
z x x y y 2
2
x y x x z x z
2 2 2
y z y y
2 x z z
z x
Y x y 2 2
X 2
z x y
y 2 z
Z z y 2
2 x Load 8
z
y 2
2 z

Whole Structure Loads 0.1kN:1m 8 EARTH_PRESSURE_AT_WALL

Plates

Plate Node A Node B Node C Node D Property

9 42 39 1 15 3
10 39 41 13 1 3
11 15 1 33 36 3
12 1 13 35 33 3
14 44 40 2 19 3
15 40 43 17 2 3
16 2 17 37 34 3
18 28 31 18 4 3
19 4 18 25 22 3
20 20 4 22 26 3
21 32 28 4 20 3
24 27 29 14 3 3
25 3 14 23 21 3
26 16 3 21 24 3
27 30 27 3 16 3
31 19 2 34 38 3
33 5 45 46 47 1
34 45 1 48 46 1
35 47 46 49 7 1

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 4 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 5 of 15
15:11
 Job No Sheet No Rev
3
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Plates Cont...
Plate Node A Node B Node C Node D Property

36 46 48 3 49 1
37 7 49 50 51 1
38 49 3 52 50 1
39 51 50 53 8 1
40 50 52 4 53 1
41 11 7 51 54 1
42 54 51 8 12 1
43 10 55 56 6 2
44 55 12 8 56 2
45 6 56 57 58 2
46 56 8 53 57 2
47 58 57 59 2 2
48 57 53 4 59 2
49 5 60 61 45 1
50 60 6 58 61 1
51 45 61 62 1 1
52 61 58 2 62 1
53 9 63 60 5 1
54 63 10 6 60 1
55 9 5 47 64 1
56 64 47 7 11 1
57 36 33 48 65 3
58 65 48 27 30 3
59 33 35 66 48 3
60 48 66 29 27 3
61 29 67 68 14 3
62 67 32 20 68 3
63 14 68 69 23 3
64 68 20 26 69 3
65 38 34 59 70 3
66 70 59 28 32 3
67 34 37 71 59 3
68 59 71 31 28 3
69 13 72 73 35 3
70 72 19 38 73 3
71 41 74 72 13 3
72 74 44 19 72 3

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
7 Rect 0.15x0.15 225.000 4.22E+3 4.22E+3 7.12E+3 CONCRETE
8 Rect 0.23x0.23 529.000 23.3E+3 23.3E+3 39.4E+3 CONCRETE

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 6 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 7 of 15
15:11
 Job No Sheet No Rev
4
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Plate Thickness
Prop Node A Node B Node C Node D Material
(cm) (cm) (cm) (cm)
1 15.000 15.000 15.000 15.000 CONCRETE
2 23.000 23.000 23.000 23.000 CONCRETE
3 20.000 20.000 20.000 20.000 CONCRETE

Supports
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
1 Fixed Fixed Fixed Fixed Fixed Fixed
2 Fixed Fixed Fixed Fixed Fixed Fixed
3 Fixed Fixed Fixed Fixed Fixed Fixed
4 Fixed Fixed Fixed Fixed Fixed Fixed
13 Fixed Fixed Fixed Fixed Fixed Fixed
14 Fixed Fixed Fixed Fixed Fixed Fixed
15 Fixed Fixed Fixed Fixed Fixed Fixed
16 Fixed Fixed Fixed Fixed Fixed Fixed
17 Fixed Fixed Fixed Fixed Fixed Fixed
18 Fixed Fixed Fixed Fixed Fixed Fixed
19 Fixed Fixed Fixed Fixed Fixed Fixed
20 Fixed Fixed Fixed Fixed Fixed Fixed
21 Fixed Fixed Fixed Fixed Fixed Fixed
22 Fixed Fixed Fixed Fixed Fixed Fixed
23 Fixed Fixed Fixed Fixed Fixed Fixed
24 Fixed Fixed Fixed Fixed Fixed Fixed
25 Fixed Fixed Fixed Fixed Fixed Fixed
26 Fixed Fixed Fixed Fixed Fixed Fixed
27 Fixed Fixed Fixed Fixed Fixed Fixed
28 Fixed Fixed Fixed Fixed Fixed Fixed
29 Fixed Fixed Fixed Fixed Fixed Fixed
30 Fixed Fixed Fixed Fixed Fixed Fixed
31 Fixed Fixed Fixed Fixed Fixed Fixed
32 Fixed Fixed Fixed Fixed Fixed Fixed
33 Fixed Fixed Fixed Fixed Fixed Fixed
34 Fixed Fixed Fixed Fixed Fixed Fixed
35 Fixed Fixed Fixed Fixed Fixed Fixed
36 Fixed Fixed Fixed Fixed Fixed Fixed
37 Fixed Fixed Fixed Fixed Fixed Fixed
38 Fixed Fixed Fixed Fixed Fixed Fixed
39 Fixed Fixed Fixed Fixed Fixed Fixed
40 Fixed Fixed Fixed Fixed Fixed Fixed
41 Fixed Fixed Fixed Fixed Fixed Fixed
42 Fixed Fixed Fixed Fixed Fixed Fixed
43 Fixed Fixed Fixed Fixed Fixed Fixed
44 Fixed Fixed Fixed Fixed Fixed Fixed

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 8 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 9 of 15
15:11
 Job No Sheet No Rev
5
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Supports Cont...
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
48 Fixed Fixed Fixed Fixed Fixed Fixed
59 Fixed Fixed Fixed Fixed Fixed Fixed
65 Fixed Fixed Fixed Fixed Fixed Fixed
66 Fixed Fixed Fixed Fixed Fixed Fixed
67 Fixed Fixed Fixed Fixed Fixed Fixed
68 Fixed Fixed Fixed Fixed Fixed Fixed
69 Fixed Fixed Fixed Fixed Fixed Fixed
70 Fixed Fixed Fixed Fixed Fixed Fixed
71 Fixed Fixed Fixed Fixed Fixed Fixed
72 Fixed Fixed Fixed Fixed Fixed Fixed
73 Fixed Fixed Fixed Fixed Fixed Fixed
74 Fixed Fixed Fixed Fixed Fixed Fixed

Primary Load Cases

Number Name Type

1 DL Dead
2 LL Live
7 EARTH_PRESSURE_AT_BASE Soil
8 EARTH_PRESSURE_AT_WALL Soil

Failed Members
There is no data of this type.

Base Pressure
Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
1 1:DL 0 0.019 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.03218 0
10:ULC, 1.2 De 0 0.025744 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
2 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.074778 0
10:ULC, 1.2 De 0 0.060 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 10 of

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 11 of
15:11
 Job No Sheet No Rev
6
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
10:ULC, 1.2 De 0 0.060 0
11:ULC, 1.5 De 0 0.072 0
12:ULC, 0.9 De 0 0.043 0
3 1:DL 0 0.019 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.03218 0
10:ULC, 1.2 De 0 0.025744 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
4 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.074778 0
10:ULC, 1.2 De 0 0.060 0
11:ULC, 1.5 De 0 0.072 0
12:ULC, 0.9 De 0 0.043 0
13 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
14 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
15 1:DL 0 0.014 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.013838 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.020 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
16 1:DL 0 0.014 0
2:LL 0 0.002 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 12 of

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 13 of
15:11
 Job No Sheet No Rev
7
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.014 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.020 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
17 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.086 0
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.084 0
12:ULC, 0.9 De 0 0.050 0
18 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.086 0
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.084 0
12:ULC, 0.9 De 0 0.050 0
19 1:DL 0 0.041 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.051 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
20 1:DL 0 0.040727 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.051 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
21 1:DL 0 0.019 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.032 0
10:ULC, 1.2 De 0 0.026 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 14 of

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 15 of
15:11
 Job No Sheet No Rev
8
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
10:ULC, 1.2 De 0 0.026 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
22 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.075 0
10:ULC, 1.2 De 0 0.059807 0
11:ULC, 1.5 De 0 0.072 0
12:ULC, 0.9 De 0 0.043 0
23 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
24 1:DL 0 0.014 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.013835 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.019857 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
25 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.085866 0
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.084 0
12:ULC, 0.9 De 0 0.050 0
26 1:DL 0 0.041 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.050893 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
27 1:DL 0 0.019 0
2:LL 0 0.002 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 16 of

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 17 of
15:11
 Job No Sheet No Rev
9
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.032 0
10:ULC, 1.2 De 0 0.026 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
28 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.074772 0
10:ULC, 1.2 De 0 0.060 0
11:ULC, 1.5 De 0 0.072 0
12:ULC, 0.9 De 0 0.043 0
29 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
30 1:DL 0 0.014 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.014 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.020 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
31 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.086 0
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.084 0
12:ULC, 0.9 De 0 0.050 0
32 1:DL 0 0.041 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.051 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 18 of

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 19 of
15:11
 Job No Sheet No Rev
10
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
10:ULC, 1.2 De 0 0.051 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
33 1:DL 0 0.019 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.032 0
10:ULC, 1.2 De 0 0.026 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
34 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.074772 0
10:ULC, 1.2 De 0 0.060 0
11:ULC, 1.5 De 0 0.072 0
12:ULC, 0.9 De 0 0.043 0
35 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
36 1:DL 0 0.014 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.014 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.020 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
37 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.086 0
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.084 0
12:ULC, 0.9 De 0 0.050 0
38 1:DL 0 0.041 0
2:LL 0 0.002 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 10 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 10 of 15
15:11
 Job No Sheet No Rev
11
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.051 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
39 1:DL 0 0.019 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.032 0
10:ULC, 1.2 De 0 0.026 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
40 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.075 0
10:ULC, 1.2 De 0 0.059807 0
11:ULC, 1.5 De 0 0.072 0
12:ULC, 0.9 De 0 0.043 0
41 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
42 1:DL 0 0.014 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.013837 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.019857 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
43 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.085866 0
10:ULC, 1.2 De 0 0.069 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 11 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 11 of 15
15:11
 Job No Sheet No Rev
12
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.084 0
12:ULC, 0.9 De 0 0.050 0
44 1:DL 0 0.041 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.050893 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
48 1:DL 0 0.019 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.011 0
9:ULC, 1.5 Dea 0 0.032 0
10:ULC, 1.2 De 0 0.026 0
11:ULC, 1.5 De 0 0.029 0
12:ULC, 0.9 De 0 0.017 0
59 1:DL 0 0.048 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.008 0
9:ULC, 1.5 Dea 0 0.075 0
10:ULC, 1.2 De 0 0.060 0
11:ULC, 1.5 De 0 0.072454 0
12:ULC, 0.9 De 0 0.043 0
65 1:DL 0 0.014 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.014 0
9:ULC, 1.5 Dea 0 0.025 0
10:ULC, 1.2 De 0 0.020 0
11:ULC, 1.5 De 0 0.022 0
12:ULC, 0.9 De 0 0.013 0
66 1:DL 0 0.024 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.007 0
9:ULC, 1.5 Dea 0 0.040 0
10:ULC, 1.2 De 0 0.032 0
11:ULC, 1.5 De 0 0.037 0
12:ULC, 0.9 De 0 0.022 0
67 1:DL 0 0.033 0
2:LL 0 0.002 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 2 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 3 of 15
15:11
 Job No Sheet No Rev
13
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.002 0
9:ULC, 1.5 Dea 0 0.052 0
10:ULC, 1.2 De 0 0.041 0
11:ULC, 1.5 De 0 0.049 0
12:ULC, 0.9 De 0 0.029 0
68 1:DL 0 0.033 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.002 0
9:ULC, 1.5 Dea 0 0.052 0
10:ULC, 1.2 De 0 0.041 0
11:ULC, 1.5 De 0 0.049 0
12:ULC, 0.9 De 0 0.029 0
69 1:DL 0 0.033 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.002 0
9:ULC, 1.5 Dea 0 0.052 0
10:ULC, 1.2 De 0 0.041 0
11:ULC, 1.5 De 0 0.049 0
12:ULC, 0.9 De 0 0.029 0
70 1:DL 0 0.041 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.003 0
9:ULC, 1.5 Dea 0 0.064 0
10:ULC, 1.2 De 0 0.051 0
11:ULC, 1.5 De 0 0.061 0
12:ULC, 0.9 De 0 0.037 0
71 1:DL 0 0.056 0
2:LL 0 0.001 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 -0.013 0
9:ULC, 1.5 Dea 0 0.086 0
10:ULC, 1.2 De 0 0.069 0
11:ULC, 1.5 De 0 0.083755 0
12:ULC, 0.9 De 0 0.050253 0
72 1:DL 0 0.033 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.002 0
9:ULC, 1.5 Dea 0 0.052 0
10:ULC, 1.2 De 0 0.041 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 4 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 5 of 15
15:11
 Job No Sheet No Rev
14
Software licensed to STAAD.Pro Part
CONNECTED User: Not signed in
Job Title Ref

By

Client File INLET Date/Time 09-Dec-2024

CHAMBER.STD 14:43

Base Pressure Cont...

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
10:ULC, 1.2 De 0 0.041 0
11:ULC, 1.5 De 0 0.049 0
12:ULC, 0.9 De 0 0.029 0
73 1:DL 0 0.033 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.002 0
9:ULC, 1.5 Dea 0 0.052 0
10:ULC, 1.2 De 0 0.041 0
11:ULC, 1.5 De 0 0.049 0
12:ULC, 0.9 De 0 0.029 0
74 1:DL 0 0.033 0
2:LL 0 0.002 0
7:EARTH_PRE 0 0.0261 0
8:EARTH_PRE 0 0.002 0
9:ULC, 1.5 Dea 0 0.052 0
10:ULC, 1.2 De 0 0.041 0
11:ULC, 1.5 De 0 0.049 0
12:ULC, 0.9 De 0 0.029 0

Base Pressure Summary

Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
Max FX 1 1:DL 0 0.019 0
Min FX 1 1:DL 0 0.019 0
Max FY 31 9:ULC, 1.5 Dea 0 0.086 0
Min FY 25 8:EARTH_PRE 0 -0.013 0
Max FZ 1 1:DL 0 0.019 0
Min FZ 1 1:DL 0 0.019 0

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 6 of 15

15:11
Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 7 of 15
15:11
 Job No Sheet No Rev
15
Part
Software licensed to STAAD.Pro
CONNECTED User: Not signed in
Job Title Ref
By
Client File INLET Date/Time 09-Dec-2024
CHAMBER.STD 14:43

Statics Check Results

L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
1:DL Loads 0 -128.607 0 86.810 0 -149.447
1:DL Reactions 0 128.607 0 -86.810 0 149.447
Difference 0 -0.000 0 0.000 0 -0.000
2:LL Loads 0 -6.440 0 4.347 0 -5.119
2:LL Reactions 0 6.440 0 -4.347 0 5.119
Difference 0 -0.000 0 0.000 0 0.000
7:EARTH_PRES Loads 0 -94.273 0 63.634 0 -84.177
7:EARTH_PRES Reactions 0 94.273 0 -63.634 0 84.177
Difference 0 -0.000 0 0.000 0 -0.000
8:EARTH_PRES Loads -25.515 0 0.000 0 -17.223 22.544
8:EARTH_PRES Reactions 0 -0.000 0 -0.000 0 -22.544
Difference -25.515 -0.000 0.000 -0.000 -17.223 0.000

Print Time/Date: 09/12/2024 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 8 of 15

15:11