Scribd
Upload
0 views

asychronous counter

The document provides an overview of the IC 7476, a dual JK flip-flop with active low inputs, operating voltage range, and temperature specifications. It includes a truth table and outlines a practical experiment to design and test a 3-bit binary asynchronous counter using the IC. The procedure, results, and precautions for the experiment are also detailed.

Uploaded by

benedictgakono
Copyright
© © All Rights Reserved
Available Formats
Download as PDF or read online on Scribd
0 views

asychronous counter

The document provides an overview of the IC 7476, a dual JK flip-flop with active low inputs, operating voltage range, and temperature specifications. It includes a truth table and outlines a practical experiment to design and test a 3-bit binary asynchronous counter using the IC. The procedure, results, and precautions for the experiment are also detailed.

Uploaded by

benedictgakono
Copyright
© © All Rights Reserved
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 3
IC 7476 Pinout Diagram The IC 7476 commonly known as IC 74LS76 is a dual JK flip IC with Set and Clear Input. The Clock, Clear inputs are active low inputs. During the High-Low Clock Transition, input data is transferred to the output. It is also a 16 pin IC. The IC 7476 can be operated from 4.75 to 5.25V and 0 to +70 degrees centigrade temperature. It works with standard TTL voltage and provides a very fast switching speed. IC 7476 truth table The truth table of IC 7476 is given below H-High logic level, X-Either LOW or HIGH logic level, L-LOW logic level, 1-Positive going transition of the clock IC 7476 Truth Table = Department of Electrical Engineering Government College of Engineering, Keonjhar EXPERIM \T: 8 STUDY OF COUNTERS, 1. STUDY OF ASYNCHRONOUS COUNTER AIM: - To design and test 3-bit binary asynchronous counter using flip-flop IC 7476. APPARATUS REQUIRED: - SLNO. | COMPONENT [ SPECIFICATION QUANTITY [- 1 TK Flip Flop | IC 7376 i 2 | BREAD BOARD. { = i 3___| RESISTOR | 2202 1 [7 “4 BATTERY { OV 1 5__ [LED I = 1 I 6 __| CONNECTING WIRE 1 = AS PER REQUIREMENT THEORY: - A counter in which each flip-flop is triggered by the output goes to previous flip-flop. As all the flip-flops do not change state simultaneously spike occur at the output. To 2void this, srobe pulse is required. Because of the propagation delay the operating speed of esynch counter is low. Asynchronous counters are easy and simple to construct. Design: MOD-8 UP COUNTER 3-bit asynchronous up counter Department of Electrical Engineering Government College of Engineering, Keonjhar 58 3-bit Asynchronous up counter Glock [Qe Qo Qa 0 0 0 0 T 0 0 r 2 0 T 0 3 0 r T 4 T 0 0 5 aes 0 1 6 T 1 0 7 1 1 7 8 0 0 0 PROCEDURE: - 1. Connect the circuit as shown in figure. 2. Apply Vcc & ground signal to the IC. 3. Apply various input data to the logic circuit. 4. Observe the input & output according to the truth table. RESULT: - The 3-bit binary asynchronous counter using flip-flop IC 7476 is verified. PRECAUTIONS: - 1. Make the connections according to the IC pin diagram. 2. The connections should be tight. 3. The Voc and ground should be applied carefully at the specified pin only. 4. Switch off supply after completing the experiment. Department of Electrical Engineering Government College of Engineering, Keonjhar 59

You might also like