97-09 English version 2/25/00 8:55 AM Page 16

S P E C I F I C A T I O N S

ENGINE 450G 550G 650G

Type................................................John Deere 4045T with altitude- John Deere 4045T with altitude- John Deere 4045T with altitude-
compensating turbocharger; compensating turbocharger compensating turbocharger
John Deere 4045D naturally
aspirated (direct drive only)
Rated power ...................................70 SAE net hp (52 kW) / 73 SAE 80 SAE net hp (59.5 kW) / 83 SAE 90 SAE net hp (67.5 kW);
gross hp (54.5 kW) @ 2,100 rpm gross hp (62 kW) @ 2,100 rpm 650G DD – 95 SAE gross hp (71 kW);
650G TC – 99 SAE gross hp (74 kW)
@ 2,100 rpm
Drawbar..........................................51 hp (38 kW) 58 hp (43 kW) 66 hp (49 kW)
Cylinders ........................................4 4 4
Displacement .................................276 cu. in. (4.524 L) 276 cu. in. (4.524 L) 276 cu. in. (4.524 L)
Fuel consumption, typical .............1.5 to 2.3 gal./hr. (4.9 to 8.7 L/h) 1.6 to 2.4 gal./hr. (6.1 to 9.1 L/h) 1.8 to 2.8 gal./hr. (6.8 to 10.6 L/h)
Maximum net torque.....................228 lb.-ft. (309 Nm) @ 1,300 rpm 260 lb.-ft. (353 Nm) @ 1,300 rpm 293 lb.-ft. (397 Nm) @ 1,300 rpm
Lubrication.....................................pressure system with full-flow spin- pressure system with full-flow spin- pressure system with full-flow spin-
on filter and oil-to-water cooler on filter and oil-to-water cooler on filter and oil-to-water cooler
Air cleaner ......................................dual stage dry type with safety dual stage dry type with safety dual stage dry type with safety
element, precleaner, and under- element, precleaner, and under- element, precleaner, and under-
hood restriction indicator hood restriction indicator hood restriction indicator
Electrical system.............................12 volt with 65-amp alternator 12 volt with 65-amp alternator 12 volt with 65-amp alternator
Cooling fan ....................................blower blower blower
TRANSMISSION full power shift, Dura-Shift with torque converter or direct drive; change gears easily using the engine decelerator
and power shift
450G TC 450G DD 550G TC 550G DD 650G TC 650G DD
mph (km/h) mph (km/h) mph (km/h) mph (km/h) mph (km/h) mph (km/h)
Maximum travel speeds
1st Forward ...............................2.30 (3.70) 1.45 (2.33) 2.31 (3.72) 1.54 (2.48) 2.28 (3.67) 1.51 (2.43)
2nd Forward .............................3.31 (5.33) 2.41 (3.88) 3.32 (5.34) 2.58 (4.15) 3.28 (5.28) 2.53 (4.07)
3rd Forward ..............................4.11 (6.61) 3.29 (5.29) 4.09 (6.58) 3.28 (5.28) 4.09 (6.58) 3.34 (5.38)
4th Forward ..............................5.91 (9.51) 5.51 (8.87) 5.88 (9.46) 5.49 (8.84) 5.87 (9.45) 5.59 (9.00)
1st Reverse ................................2.50 (4.02) 1.60 (2.57) 2.50 (4.02) 1.70 (2.74) 2.46 (3.96) 1.67 (2.69)
2nd Reverse...............................3.58 (5.76) 2.67 (4.30) 3.59 (5.78) 2.85 (4.59) 3.54 (5.70) 2.80 (4.51)
3rd Reverse................................4.47 (7.19) 3.63 (5.84) 4.36 (7.02) 3.62 (5.83) 4.30 (6.92) 3.70 (5.95)
4th Reverse ...............................5.93 (9.54) 6.09 (9.80) 5.86 (9.43) 6.06 (9.75) 5.80 (9.33) 6.19 (9.96)
FINAL DRIVES large heavy-duty final drive assemblies attach directly to the transverse case and are isolated from the track
frame to keep final drives from being adversely affected by shock loads; 450G is single reduction, 550G and
650G are double
STEERING/BRAKES oil-cooled and modulated steering system; multiple wet-disk steering clutches and wet-band steering brakes are
pressure lubricated and located at the rear of the machine for easy servicing
AUTOMATIC PARK BRAKE exclusive safety feature engages whenever the engine stops, preventing machine operation, which eliminates
brake damage
HYDRAULIC SYSTEM
System ............................................open center open center open center
Pressure, main relief.......................2,750 psi (18 961 kPa) 2,750 psi (18 961 kPa) 2,750 psi (18 961 kPa)
Pump ..............................................gear gear gear
Flow................................................17 gpm (64 L/min.) @ 2,100 rpm 17 gpm (64 L/min.) @ 2,100 rpm 17 gpm (64 L/min.) @ 2,100 rpm
Filter, return oil..............................10 micron 10 micron 10 micron
Control...........................................T-bar three function T-bar three function T-bar three function
Cylinders ........................................heat-treated, chrome-plated, heat-treated, chrome-plated, heat-treated, chrome-plated,
polished cylinder rods with hard- polished cylinder rods with hard- polished cylinder rods with hard-
ened steel (replaceable bushings) ened steel (replaceable bushings) ened steel (replaceable bushings)
pivot pins pivot pins pivot pins
UNDERCARRIAGE John Deere Dura-TraxTM features large deep-heat-treated components; pins and bushings are sealed for life;
rollers and idlers are permanently sealed and lubricated; full-length track frame covers reduce material buildup
and ease cleaning
Chain
Standard....................................sealed sealed sealed
Optional....................................sealed and lubricated sealed and lubricated sealed and lubricated
Pitch..........................................6.29 in. (159.8 mm) 6.29 in. (159.8 mm) 6.73 in. (171.1 mm)

16
97-09 English version 2/25/00 8:55 AM Page 17

S P E C I F I C A T I O N S

UNDERCARRIAGE (continued) 450G 550G 650G

STANDARD TRACK
Grouser .....................................16 in. (406 mm) closed center not available 18 in. (457 mm) closed center
single bar single bar
Ground contact area.................2,432 sq. in. (15 690 cm2) 3,082 sq. in. (19 884 cm2)
Ground pressure
Torque converter.................6.55 psi (45.2 kPa) 6.01 psi (41.4 kPa)
Direct drive..........................6.47 psi (44.6 kPa) 5.94 psi (41.0 kPa)
Overall width over track...........73 in. (1854 mm) 79 in. (2007 mm)
Track shoes, each side ..............37 38
Length of track on ground .......76 in. (1930 mm) 85.6 in. (2174 mm)
Track gauge...............................57 in. (1450 mm) 61 in. (1550 mm)
Track rollers ..............................5 6
Adjustment ...............................hydraulic with hinged dirt cover hydraulic with hinged dirt cover
LONG TRACK
Grouser .....................................16 in. (406 mm) closed center 18 in. (457 mm) closed center not available
single bar single bar
Ground contact area.................2,733 sq. in. (17 632 cm2) 2,732 sq. in. (19 834 cm2)
Ground pressure
Torque converter.................6.04 psi (41.7 kPa) 6.47 psi (44.7 kPa)
Direct drive..........................5.97 psi (41.1 kPa) 6.4 psi (44.1 kPa)
Overall width over track...........73 in. (1854 mm) 79 in. (2007 mm)
Track shoes, each side ..............40 40
Length of track on ground .......85 in. (2160 mm) 85.4 in. (2169 mm)
Track gauge...............................57 in. (1450 mm) 61 in. (1550 mm)
Track rollers ..............................6 6
Adjustment ...............................hydraulic with hinged dirt cover hydraulic with hinged dirt cover
LOW GROUND PRESSURE
Grouser .....................................24 in. (610 mm) closed center 24 in. (610 mm) closed center 24 in. (610 mm) closed center
single bar single bar single bar
Ground contact area.................4,099 sq. in. (26 445 cm2) 4,099 sq. in. (26 447 cm2) 4,109 sq. in. (26 510 cm2)
Ground pressure
Torque converter.................4.25 psi (29.3 kPa) 4.52 psi (31.2 kPa) 4.70 psi (32.4 kPa)
Direct drive..........................4.20 psi (29.0 kPa) 4.47 psi (30.8 kPa) 4.65 psi (32.1 kPa)

Grouser ...................................................................................................................................................................26 in. (660 mm) closed center

single bar
Ground contact area ..............................................................................................................................................4,451 sq. in. (28 717 cm2)
Ground pressure
Torque converter ..............................................................................................................................................4.45 psi (30.7 kPa)
Direct drive .......................................................................................................................................................4.41 psi (30.4 kPa)

Overall width over track...........93 in. (2362 mm) 93 in. (2362 mm) 93 in. (2362 mm)
Track shoes, each side ..............40 40 38
Length of track on ground .......85 in. (2160 mm) 85.4 in. (2169 mm) 85.6 in. (2174 mm)
Track gauge...............................69 in. (1750 mm) 69 in. (1750 mm) 69 in. (1750 mm)
Track rollers ..............................6 6 6
Adjustment ...............................hydraulic with hinged dirt cover hydraulic with hinged dirt cover hydraulic with hinged dirt cover
CAPACITIES (U.S.)
Fuel tank with lockable cap ...........41 gal. (155.2 L) 41 gal. (155.2 L) 41 gal. (155.2 L)
Cooling system with coolant
recovery tank ............................18 qt. (17.0 L) 18 qt. (17.0 L) 18 qt. (17.0 L)
Engine oil including spin-on filter ....9 qt. (8.5 L) 13 qt. (12.3 L) 13 qt. (12.3 L)
Transmission system including
spin-on filter in filter center
Torque converter ......................27 gal. (102 L) 27 gal. (102 L) 27 gal. (102 L)
Direct drive ...............................27 gal. (102 L) 27 gal. (102 L) 27 gal. (102 L)
Final drive (each) ...........................7 qt. (6.6 L) 10 qt. (9.5 L) 10 qt. (9.5 L)
Hydraulic reservoir.........................10 gal. (37.8 L) 10 gal. (37.8 L) 10 gal. (37.8 L)
Hydraulic system including
vertical spin-on filter in
filter center ...............................14.6 gal. (55.3 L) 14.6 gal. (55.3 L) 15 gal. (56.8 L)
All capacities are for torque converter unless otherwise noted. All power train and hydraulic systems allow 45-degree maximum fore-aft, side-to-side
operation without modification.

17
97-09 English version 2/25/00 8:55 AM Page 18

S P E C I F I C A T I O N S / D I M E N S I O N S

OPERATING WEIGHTS 450G 550G 650G

With standard equipment With standard equipment With standard equipment
450G TC 450G DD 550G TC 550G DD 650G TC 650G DD
lb. (kg) lb. (kg) lb. (kg) lb. (kg) lb. (kg) lb. (kg)
Standard track ................................15,932 (7243) 15,732 (7152) not available not available 18,510 (8414) 18,310 (8323)
Wide track ......................................16,888 (7677) 16,688 (7586) not available not available not available not available
Long track ......................................16,510 (7505) 16,310 (7415) 17,683 (8038) 17,483 (7947) not available not available
Low ground pressure (LGP) ...........17,432 (7924) 17,232 (7833) 18,530 (8423) 18,330 (8332) 19,322 (8783) 19,122 (8692)
DIMENSIONS
A Overall height with ROPS
and cab...............................108 in. (2740 mm) 109 in. (2770 mm) 110 in. (2794 mm)
Overall height with low-
profile ROPS.......................103.3 in. (2624 mm) 104.3 in. (2649 mm) 105.3 in. (2675 mm)
B Overall length
Standard and wide tracks .....154.2 in. (3917 mm) 160 in. (4070 mm) 160 in. (4070 mm)
B' Overall length
Long and low ground
pressure tracks ..............156.5 in. (3975 mm) 160 in. (4070 mm) 160 in. (4070 mm)
C Blade lift height.......................32.1 in. (815 mm) 34.1 in. (866 mm) 35.7 in. (906 mm)
D Digging depth .........................19.9 in. (504 mm) 18.1 in. (460 mm) 16.5 in. (420 mm)
E Blade cutting edge angle,
two position adjustable .....50 or 55 degrees 50 or 55 degrees 50 or 55 degrees
G-SERIES BLADE SPECS
STANDARD BLADE
F Width ......................................97 in. (2464 mm) 105 in. (2667 mm) 105 in. (2667 mm)
G Height......................................32.6 in. (827 mm) 33.3 in. (847 mm) 35.4 in. (898 mm)
SAE capacity ............................2.0 cu. yd. (1.5 m3) 2.3 cu. yd. (1.7 m3) 2.5 cu. yd. (1.9 m3)
H Blade angle ..............................25 degrees 25 degrees 25 degrees
I Angled width...........................87.8 in. (2230 mm) 95.1 in. (2415 mm) 95.1 in. (2415 mm)
J Tilt ...........................................13.0 in. (330 mm) 14.1 in. (357 mm) 13.5 in. (343 mm)
NARROW BLADE (Will not cover standard track footprint when fully angled.)
F Width ......................................91 in. (2311 mm) 97 in. (2464 mm) 97 in. (2464 mm)
G Height......................................32.6 in. (827 mm) 32.6 in. (827 mm) 32.6 in. (827 mm)
SAE capacity ............................1.9 cu. yd. (1.4 m3) 2.0 cu. yd. (1.5 m3) 2.0 cu. yd. (1.5 m3)
H Blade angle ..............................25 degrees 25 degrees 25 degrees
I Angled width...........................82.4 in. (2093 mm) 87.8 in. (2230 mm) 87.8 in. (2230 mm)
J Tilt ...........................................12.2 in. (309 mm) 13.0 in. (330 mm) 12.5 in. (317 mm)
WIDE BLADES
F Width ......................................115 in. (2921 mm) 115 in. (2921 mm) 115 in. (2921 mm)
G Height......................................32.6 in. (827 mm) 32.6 in. (827 mm) 32.6 in. (827 mm)
SAE capacity ............................2.3 cu. yd. (1.8 m3) 2.3 cu. yd. (1.8 m3) 2.3 cu. yd. (1.8 m3)
H Blade angle ..............................23 degrees 23 degrees 23 degrees
I Angled width...........................105.7 in. (2686 mm) 105.7 in. (2686 mm) 105.7 in. (2686 mm)
J Tilt ...........................................15.4 in. (391 mm) 15.4 in. (391 mm) 14.8 in. (376 mm)

F Width ......................................121 in. (3073 mm) 121 in. (3073 mm) 121 in. (3073 mm)
G Height......................................32.6 in. (827 mm) 32.6 in. (827 mm) 32.6 in. (827 mm)
SAE capacity ............................2.5 cu. yd. (1.9 m3) 2.5 cu. yd. (1.9 m3) 2.5 cu. yd. (1.9 m3)
H Blade angle ..............................23 degrees 23 degrees 23 degrees
I Angled width...........................111.3 in. (2827 mm) 111.3 in. (2827 mm) 111.3 in. (2827 mm)
J Tilt ...........................................16.2 in. (411 mm) 16.2 in. (411 mm) 15.6 in. (396 mm)

F Width ....................................................................................................................................................................128 in. (3250 mm)

G Height ...................................................................................................................................................................32.6 in. (827 mm)
SAE capacity ..........................................................................................................................................................2.6 cu. yd. (2.0 m3)
H Blade angle ............................................................................................................................................................23 degrees
I Angled width ........................................................................................................................................................117.8 in. (2992 mm)
J Tilt .........................................................................................................................................................................16.6 in. (421 mm)

18
97-09 English version 2/25/00 8:55 AM Page 19

D I M E N S I O N S / S P E C I F I C A T I O N S

14.25 in. (362 mm)

Ground Clearance
G C
Ground Line E
J

12 in. (305 mm) D

Concrete Level F
6 in. (152 mm) Rigid Drawbar
1.9 in. (49 mm) 11.5 in. (292 mm) Extended Drawbar
single grouser height
B

B'

Unit illustrated above is equipped with extended drawbar.

H H

FORESTRY APPLICATION available limb risers and screens for the rollover protective structure, John Deere-built 4000 Winch for versatile
skidding and clearing operations
K 4000 Winch length .................28.1 in. (713 mm)
DRAWBAR PULL
Crawler speed vs ground pull ................usable pull will depend on traction and weight of tractor
160 160 160

450G 550G 650G

32 TORQUE CONVERTER 32 TORQUE CONVERTER
32 TORQUE CONVERTER
140 140 140
DIRECT DRIVE DIRECT DRIVE DIRECT DRIVE

28 28 28
120 120 120

24 24 24

100 100 100

20 20 20
DRAWBAR PULL x 1000 N (lb.)
DRAWBAR PULL x 1000 N (lb.)
DRAWBAR PULL x 1000 N (lb.)

80 80 80

16 16 16

60 60 60

12 12 12

40 40 40
8 8 8

20 20 20
4 4 4
lb.
lb.
lb.

N
N
N

km/h 0 1 2 3 4 5 6 7 8 9 km/h 0 1 2 3 4 5 6 7 8 9 km/h 0 1 2 3 4 5 6 7 8 9

mph 0 1 2 3 4 5 6 mph 0 1 2 3 4 5 6 mph 0 1 2 3 4 5 6
SPEED SPEED SPEED

19
97-09 English version 2/25/00 8:55 AM Page 20

A D D I T I O N A L E Q U I P M E N T

450G 550G 650G 450G 550G 650G 450G 550G 650G

ENGINE Rubber track pads* ■ ■ ■ Non-suspension vinyl seat ■ ■ ■
Coolant recovery tank ● ● ● Sealed and lubricated chain ■ ■ ■ Adjustable armrests, backrest, and
Enclosed safety fan guard ● ● ● LIGHTS
fore-aft – Conforms to SAE J899
Conforms to SAE J1308 Radio, AM/FM weather band ■ ■ ■
Two front driving/working and one rear
Engine coolant –34°F (–37°C) ● ● ● ROPS protection, low profile ■ ■ ■
working halogen, 33,000 candlepower
Natural aspiration (direct drive only) ● (375 737 lux each) ■ ■ ■
Door screens* / Front screens* / Limb
Oil-to-water engine oil cooler ● ● ● risers* – Arched or point-to-point
Quick release fuel filter ● ● ● OPERATOR’S STATION with overhead exhaust* / Rear screen /
Trash-resistant six-fin radiator ● ● ● Built-in Operator’s Manual storage Side screens
Underhood muffler with vertical compartment and manual ● ● ● ROPS protection, standard height ■ ■ ■
exhaust stack ● ● ● Decelerator ● ● ● Door screens* / Front screens* / Limb
Spark arrester: Deluxe suspension vinyl seat ● ● ● risers* – Arched or point-to-point
Torque converter ● ● ● Adjustable armrests, thigh support, with overhead exhaust* / Rear screen /
Direct drive* ■ ● ● backrest, height/weight, and fore-aft – Side screens
Heavy-duty six-fin radiator ■ ■ ● Conforms to SAE J899 ROPS-to-cab conversion panels* ■ ■ ■
Electric ether start aid ■ ■ ■ Electronic monitor system with audible Seat belt, 3 in. (76 mm), without retractors ■ ■ ■
Engine coolant heater, 1,000 watts, and visual warning ● ● ● Conforms to SAE J386
110 volts ■ ■ ■ Coolant temperature / Engine oil Steering conversion kits* ■ ■ ■
Fuel/water separator* ■ ■ ■ pressure / Hydraulic filter restric- Suspension vinyl seat for backhoe use ■ ■ ■
Radiator sand screen (requires blower fan) ■ ■ ■ tion / Low alternator voltage / Adjustable armrests, thigh support,
Reversible fan ■ ■ ■ Transmission filter restriction / backrest, height/weight, and fore-
Turbocharger ■ ● ● Transmission pressure / Transmis- aft – Conforms to SAE J899
sion temperature OVERALL VEHICLE
POWER TRAIN
Fuel gauge, electric, illuminated ● ● ● Perforated engine side shields ● ● ●
Automatic spring-applied, hydraulic-
Gauge/indicator package ■ ■ ■ ● ● ●
released park brake, lever operated ● ● ● Gauges, illuminated
Reverse alarm
Cooler ● ● ● Engine coolant temperature / Engine
Switchable to 97 dB(A) or 111 dB(A) /
Oil-to-air for torque converter Conforms to SAE J994, J1446
oil pressure / Transmission oil
transmission ● ● ● Vandal protection ● ● ●
temperature
Primary and secondary service brakes ● ● ● Indicator lights
Engine access door / Fuel tank cap /
Transmission neutral lock with starter Hydraulic and transmission access
Low alternator voltage / Trans-
safety switch ● ● ● mission oil filter restriction /
door / Instrument panel
Winch drive with cover ● ● ● Transmission oil pressure
Backhoe with 24-in. (610 mm) standard
Axle seal guards* ■ ■ ■ bucket, 3,350 lb. (1522 kg) ■ ■ ■
Horn, electric ● ● ● Alternate stabilizer pads / Backhoe
Direct drive transmission with oil-to-air
Conforms to SAE J994, J1446
cooler, decelerator, declutch, and sus- bucket coupler / Backhoe mounts /
Hourmeter, electric, illuminated ● ● ●
pended power control inching pedal ■ ■ ■ Interior-mounted rearview mirror ● ● ●
Extendable dipperstick* / Hydraulic
and mechanical quick disconnects /
ELECTRICAL Conforms to SAE J985
12–36-in. (305–914 mm) standard,
Auto-reset circuit breakers ● ● ● Key start switch with electric fuel shutoff ● ● ● heavy-duty, and extra heavy-duty
By-pass start safety cover at starter ● ● ● Modular design ROPS/FOPS canopy ● ● ● buckets
Positive terminal battery covers ● ● ● Conforms to SAE J1040
Counterweights, rear, 300 lb. (136 kg)
Single battery, 180-min. reserve capacity, Pedal steering ● ● ● each (five maximum) ■ ■ ■
625 CCA ● ● ● Seat belt, 2 in. (51 mm), with retractors ● ● ● Counterweights, with/without draw-
Auxiliary starting receptacle under hood ■ ■ ■ Conforms to SAE J386
bars, 2 in. (51 mm) thick, 300 lb.
Dual batteries, 360-min. reserve capacity, Slip-resistant steps and ergonomically-
(136 kg) each ■ ■ ■
1,250 CCA ■ ■ ■ located handrails ● ● ● Extended drawbar with pin for pull-
Master electrical disconnect switch, Conform to SAE J185
type implements ■ ■ ■
lockable ■ ■ ■ Tool storage behind seat ● ● ● Recommend rear screen
Cab ■ ■ ■ Fireplow* ■ ■ ■
HYDRAULIC SYSTEM Air conditioning, 33,000 Btu* / Deluxe
“O” ring face seal connectors ● ● ● Front tow hook ■ ■ ■
headliner / Dome light / Floormat /
Fourth and/or fifth function valve (with Heavy-duty grille screen ■ ■ ■
Fresh air intake heater/defroster/
or without float) and levers for auxiliary PTO* ■ ■ ■
pressurizer, fresh air precleaner,
equipment* ■ ■ ■ Rigid drawbar with pin ■ ■ ■
400 CFM, 40,000 Btu/hr (11.7 kW) –
Power-beyond valve for front/rear Recommend rear screen
Conforms to SAE J1503, J1535D /
auxiliary valves ■ ■ ■ Ripper, parallelogram with five shank
Front and rear windshield wipers /
Pump, 23 gpm, with hydraulic oil cooler ■ ■ ■ pockets and three teeth, 1,380 lb.
Front and rear windshield washers /
(626 kg) ■ ■ ■
UNDERCARRIAGE Interior-mounted rearview mirror /
Ripper, radial with five shank pockets
Tinted safety glass / Conforms to
Front idler and sprocket bolt-on chain and three teeth, 742 lb. (336 kg) ■
● ● ● SAE J1040
guides SMV emblem ■ ■ ■
Full-length track frame covers ● ● ● Cab protection ■ ■ ■ Swinging drawbar* ■ ■ ■
■ ■ ■ Door screens* / Front screens* / Lexan®
Bolt-on full-length track guards Tachometer* ■ ■ ■
Margard® windows* / Limb risers* –
Counterweights, front idler, 350 lb. Three-point hitch, hydraulic actuated* ■ ■ ■
■ ■ ■ Arched or point-to-point with over-
(158 kg) each Winch, front* ■ ■ ■
Counterweights, sprocket, 564 lb. (256 kg) head exhaust* / Rear screen / Side
Winch, rear, John Deere Model 4000,
total ■ ■ ■ screens
1,190 lb. (540 kg) – Rear screen
Full grouser track shoes, 16 in. (406 mm) Dual lever dozer controls ■ ■ ■ required ■ ■ ■
to 24 in. (610 mm), for direct drive Headliner for ROPS ■ ■ ■ Freespool function / Power in, power
transmissions* ■ ■ ■ Lever steering ■ ■ ■ out optional / Standard or low speed /
Closed and open center track shoes* ■ ■ ■ Low-profile ROPS ■ ■ ■ Compatible drawbar / Fair-lead,
Conforms to SAE J1040
four roller / Log arch*

KEY: ● Standard equipment ■ Optional or special equipment *See your John Deere dealer for further information.

Net engine power is with standard equipment including air cleaner, exhaust Specifications and design subject to change without notice. Wherever applicable, specifications are
system, alternator, and cooling fan, at standard conditions per SAE J1349 and in accordance with SAE standards. Except where otherwise noted, these specifications are based on
DIN 6270B, using No. 2-D fuel at 35 API gravity. No derating is required up to units with rollover protective structures, full fuel tanks, 175-lb. (79 kg) operators, and standard
5,000 ft. (1500 m) altitude for the 450G and up to 10,000 ft. (3050 m) altitude equipment; 450G unit with 97-in. (2464 mm) PAT Blade for standard gauge or 121-in. (3073 mm)
for the 550G and 650G. Gross power is without cooling fan. PAT Blade for wide gauge; and 550G and 650G units with 105-in. (2667 mm) PAT Blade.

20
DKA450G Litho in U.S.A. (97-09)