Sr.No.

Question Ans Marks

1 CMRR parameter in an instrumentation amplifier a Each
stands for ____ 1
a) Common mode rejection ratio
b) Common medium rejection ratio
c) Common mode ratio of reference
d) None of the above
2 Determine the output from the following circuit b

a) 180o in phase with input signal

b) 180o out of phase with input signal
c) Same as that of input signal
d) Output signal cannot be determined
3 Which of the following electrical characteristics is not c
exhibited by an ideal op-amp?
a) Infinite voltage gain
b) Infinite bandwidth
c) Infinite output resistance
d) Infinite slew rate
4 Find the output voltage of an ideal op-amp. If V1 and V2 b
are the two input voltages
a) VO= V1-V2
b) VO= A×(V1-V2)
c) VO= A×(V1+V2)
d) VO= V1×V2
5 How will be the output voltage obtained for an ideal op- a
amp?
a) Amplifies the difference between the two input
voltages
b) Amplifies individual voltages input voltages
c) Amplifies products of two input voltage
d) None of the mentioned
6 Which is not the ideal characteristic of an op-amp? a
a) Input Resistance –> 0
b) Output impedance –> 0
c) Bandwidth –> ∞
d) Open loop voltage gain –> ∞

7 Find the input voltage of an ideal op-amp. It’s one of d

the inputs and output voltages are 2v and 12v.
(Gain=3)
a) 8v
b) 4v
c) -4v
d) -2v
8 To increase the value of CMRR, which circuit is used a
to replace the emitter resistance Re in differential
amplifier?
a) Constant current bias
b) Resistor in parallel with Re
c) Resistor in series with Re
d) Diode in parallel with Re
9 What is the purpose of diode in differential amplifier a
with constant current circuit?
a) Total current independent on temperature
b) Diode is dependent of temperature
c) Transistor is depend on temperature
d) None of the mentioned
10 How to improve CMRR value b
a) Increase common mode gain
b) Decrease common mode gain
c) Increase Differential mode gain
d) Decrease differential mode gain
11 Define total current (IQ) equation in differential amplifier c
with constant current bias current
a) IQ=1/R3×(VEE/R1+R2)
b) IQ =(VEE×R2)/(R1+R2)
c) IQ=1/R3×(VEE×R2/R1+R2)
d) IQ)=R3×(VEE/R1+R2)
12 Constant current source in differential amplifier is also a
called as
a) Current Mirror
b) Current Source
c) Current Repeaters
d) All of the mentioned
13 An ideal op-amp requires infinite bandwidth because a
a) Signals can be amplified without attenuation
b) Output common-mode noise voltage is zero
c) Output voltage occurs simultaneously with input
voltage changes
d) Output can drive infinite number of device
14 An op amp has a voltage gain of 500,000. If the output A
voltage is 1 V, the input voltage is

a) 2 microvolts
b) 5 mV
c) 10 mV
d) 1V

15 When slew-rate distortion of a sine wave occurs, the b

output

a) Is larger
b) Appears triangular
c) Is normal d) Has no offset
16 A 741C has d

a) A voltage gain of 100,000

b) An input impedance of 2 Mohm
c) An output impedance of 75 ohm
d) All of the above

17 The closed-loop voltage gain of an inverting amplifier c

equals

a) The ratio of the input resistance to the feedback

resistance
b) The open-loop voltage gain
c) The feedback resistance divided by the input
resistance
d) The input resistance

18 What is the voltage difference between the input a

terminals of an op-amp in normal operation?

a) Virtually zero
b) 5V
c) 15 V
d) 22

19 f Rf = Rin, the voltage gain Vout/Vin of non inverting

amplifier is ___.

a) 1
b) -1
c) 10
d) small

20 The output voltage of an op-amp circuit is always ___ b

the level of the power supply.

a) larger than
b) the same as
c) smaller than
d) None of the above

21 A voltage summing amplifier has ___ b

a) several inputs and several outputs

b) several inputs and one output
c) one input and several outputs
d) one input and one output
22 The voltage gain of a buffer amplifier is ___ . a

a) 1
b) 0
c) –1
d) –5

23 The input impedance of a buffer amplifier is ___. d

a) very low
b) low
c) high
d) very high

24 The input stage of an Op-amp is usually a ………. a

a) differential amplifier
b) class B push-pull amplifier
c) CE amplifier
d) damped amplifier

25 The common-mode voltage gain is ……… a

a) smaller than differential voltage gain

b) equal to differential voltage gain
c) greater than differential voltage gain
d) none of the above

26 A common-mode signal is applied to ………. c

a) the noninverting input

b) the inverting input
c) both inputs
d) top of the tail resistor

27 The input offset current equals the ………. a

a) difference between two base currents

b) average of two base currents
c) collector current divided by current gain
d) none of these

28 The Op-amp can amplify c

a) a.c. signals only

b) d.c. signals only
c) both a.c. and d.c. signals
d) neither d.c. nor a.c. signals
29 If the feedback resistor is open, the voltage gain ……. a

a) Increases
b) Decreases
c) is not affected
d) depends on Ri

30 A certain noninverting amplifier has Ri of 1 kΩ and Rf c

of 100 kΩ. The closed loop voltage gain is ………

a) 100,000
b) 1000
c) 101
d) 100

31 The use of negative feedback ……… d

a) reduces the voltage gain of an Op-amp

b) makes the Op-amp oscillate
c) makes linear operation possible
d) answers (1) and (2)

32 For an Op-amp with negative feedback, the output is c

…….

a) equal to the input

b) increased
c) feed back to the inverting input
d) feed back to the noninverting input

33 The output of a particular Op-amp increases 8V in b

12μs. The slew rate is …….

a) 90 V/μs
b) 0.67 V/μs
c) 1.5 V/μs
d) none of these

34 A certain OP-amp has bias currents of 50 μA. The a

input offset current is ……..

a) 700 nA
b) 99.3 μA
c) 49.7 μA
d) none of these
35 Of the values listed, the most realistic value for open- d
loop voltage gain of an OP-amp is ……

a) 1
b) 80 dB
c) 2000
d) 100,000

36 With zero volts on both inputs, an OP-amp ideally c

should have an output..

a) equal to the positive supply voltage

b) equal to the negative supply voltage
c) equal to zero
d) equal to CMRR

37 A rectifier output is a d

a) Pure dc signal
b) Pure ac signal
c) Partial dc signal
d) pulsating dc signal

38 Clamping circuit depend mostly on c

a) Capacitance of the circuit

b) Resistance of the circuit
c) Time constant of the circuit
d) None of these

39 A positive half wave rectifier is a b

a) Positive clipper
b) negative clipper
c) negative clamper
d) None of these

40 When only the low frequencies are allowed to pass to a

the output, the filter is known as:

a) low-pass filter
b) high-pass filter
c) bandpass filter
d) band-stop filter
41 When a full band of frequencies is allowed to pass c
through a filter circuit to the output, the resonant circuit
is called a:

a) low-pass filter
b) high-pass filter
c) bandpass filter
d) band-stop filter

42 The zero level detector is application of d

a) differentiator
b) summing amplifier
c) integrator
d) comparator

43 A comparator with hysteresis b

a) has 1 trigger point

b) has 2 trigger points
c) has variable trigger point
d) is like magnetic circuit

44 For a step input ,output of integrator is b

a) Pulse c) Ramp
b) Triangular wave d) Spike

45 The use of negative feedback d

a) reduces the voltage gain of an Op-amp

b) makes the Op-amp oscillate
c) makes linear operation possible
d) Both A and B

46 The input offset current is usually c

a) Less than the input bias current

b) Equal to zero
c) Less than the input offset voltage
d) Unimportant when a base resistor is used

47 The typical input stage of an op amp has a c

a) Single ended input and single ended output

b) Single ended input and differential output
c) Differential input and single ended output
d) Differential input and differential output
48 When a large sine wave drives a Schmitt trigger, the a
output is a

a) Rectangular wave
b) Triangular wave
c) Rectified sine wave
d) Series of ramps

49 If the input is a rectangular pulse, the output of an c

opamp integrator is a

a) Sine wave
b) Square wave
c) Ramp
d) Rectangular pulse

50 Hysteresis prevents false triggering associated with b

a) A sinusoidal input
b) Noise voltages
c) Stray capacitances
d) Trip points