SLR-JE-119

Seat
No. Set p
T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Transmission System Design (BTN02601)
Day & Date: Tuesday, 21-05-2024 Max. Marks: 56
Time: 03:00 PM To 06:00 PM
Instructions: I) Answer any two questions fromeach section.
2) Figures to the right indicate full marks.
3) Assume suitable data if necessary and mention it clearly.

Section —I

Q.2 a) Derive the Lewis beam strength equationfor spur gear tooth. 03
b) Explain force analysis on Spur gear with the help of figure. 04
c) A pair of spur gears with 200 pressure angle, consists of a 17 teeth pinion 07
meshing with 68 teeth gear. The module and face width are 2.5 and 25 mm
respectively. The gears are machined to meet the specifications of Grade 10
and are heat treated to a surface hardness of 250 BHN. Determine:
i) The optimumspeed for maximumpowertransmittingcapacity; and
ii) The maximumpowertransmittedby the gears at the above speed.

Q.3 a) Discuss force analysis of helical gear. 03

b) Derive the expression for virtual number of teeth for helical gears. 04
c) A pair of parallel helical gears consists of a 20 teeth pinion meshing with a 100 07
teeth gear. The pinion rotates at 720 rpm. The normal pressure angle is 20 0,
while the helix angle is 25 0. The face width is 40 mm and the normal module is
4 mm. The pinionas well as the gear is made of steel 40C8 (Sut = 600 N/mm2)
and heat treated to a surface hardness of 300 BHN. The service factor and the
factor of safety are 1.5 and 2 respectively. Assume that the velocity factor
accounts for the dynamic load and calculate the powertransmittingcapacity of
gears.

Q.4 a) Discuss advantages and disadvantages of wormgear drives. 03

b) Define the following terms related to worm gear 04
i) Lead
ii) Lead Angle
iii) Helix Angle
iv) Single-start threads
c) A pair Ofwormgears is designated as, 1130/10/8Calculate 07
i) the center distance;
ii) the speed reduction;
iii) the dimensions of the worm; and
iv) the dimensions of the worm wheel

Page 3 of 16
 T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Design (BTN02601)
Day & Date: Tuesday, 21-05-2024 Max. Marks: 70
Time: 03:00 PM To 06:00 PM
Instructions: 1) Q. No. 1 is compulsory. It should be solved in the first 30 minutes in
answer book Page no 03 (Starting page of the Answer Book). Each
question carries one mark.
2) Don't forget to Mentionquestion paper set (P/Q/R/S) on top of page.
3) Figures to the right indicates full marks.
4) Assume suitable data if necessary and mentionit clearly.

MCQ/Objective Type Questions

Duration: 30 Minutes Marks: 14

Q.' Choose the correct alternativesfrom the options and rewritethe sentence. 14
1) The initial contact in helical gears is
a) point b) line
c) surface d) unpredictable
2) Compared with spur gears, helical gears
a) run more smoothly b) run with noise and vibrations
c) consumeless power d) run exactly alike
3) In helical gears, the distance betweentwo similar points on adjacent teeth,
measured in a plane perpendicularto tooth element, is called
a) normalcircular pitch b) transverse circular pitch
c) axial pitch d) diametral pitch
4) In case of spur gears, Lewis formfactor depends upon
a) module b) numberof teeth
c) pressure angle d) b and c
5) When two identical bevel gears are used to transmit power between
shafts that are intersecting at right angle, they are called,
a) spiral bevel gears b) Mitergears
c) straight bevel gears d) hypoid gears
6) The rootangle of a bevel gear is equal to
a) pitchangle + addendumangle b) pitchangle - addendumangle
c) pitch angle + dedendum angle d) pitchangle - dedendumangle
7) The brake used in most of motorcycles is
a) internalexpanding brake b) block brake
c) band brake d) disk brake
8) In Lewis equation, gear tooth is considered as
a) simply supportedbeam b) cantilever beam
c) curved beam d) none of the above

Page 1 of 16

SLR-JE-119
Set
9) According to Lewis equation
a) pinion is always weaker than gear
b) pinion is weaker than gear if made of same material
c) gear is weaker than pinion if made of same material
d) none of the above
10) The friction material of the brake should have
a) high coefficient of friction b) low coefficient of friction
c) high surface hardness d) high endurance limit strength
11) In thrust bearings, the load acts
a) along the axis of rotation
b) perpendicularto the axis of rotation
c) parallel to the axis of rotation
d) a and c
12) Worm gears are widely used when
a) velocity ratio is high
b) space is limited
c) axes of shafts are non-intersecting
d) all the three
13) The main advantage of worm gear drive is
a) ease of manufacturing b) high velocity ratio
c) low power loss d) low cost
14) Taper roller bearing is used to take
a) only radial load b) only axial load
c) only torque d) both axial and radial loads
 SLR-JE-119
Set
Section — Il

Q.5 a) Explain terminologyused in straight bevel gear. 03

b) Discuss various mountingmethodsof bevel gears withfigure. 04
c) A pair of straight bevel gears consists of a 24-teeth pinion meshing with a 07
48 teeth gear. The module at the outside diameter is 6 mm, while the face width
is 50 mm. The gears are made of grey cast iron FG 220 (Sut = 220 N/mm2).
The pressure angle is 200. The teeth are generated and assume that velocity
factor accounts for the dynamic load. The pinion rotates at 300 rpm and the
service factor is 1.5. The Lewis form factor based on formativenumberof teeth
= 0.3473 and = 5.6/(5.6+ Uv).
Calculate:
i) the beam strength of the tooth
ii) the static load that the gears can transmit with a factor of safety of 2 for
bending consideration; and
iii) the rated power that the gears can transmit

Q.6 a) Discuss Hydrodynamicbearing with neat sketch. 03

b) With the help of figure explain any 4 types of Rolling Contact Bearings. 04
c) A shaft transmitting50 kW at 125 rpm from the gear Gl to the gear G2 and 07
mountedon two single-row deep groove ball bearings Bl and B2 is shown in
Fig. The gear toothforces are Pti = 15915N, Pri= 5793 N, Pt2 = 9549 N, Pr2
= 3476 N. The diameterof the shaftat bearings Bl and B2 is 75 mm. The load
factor is 1.4 and the expected life for 90% of the bearings is 10000 h. Find
Dynamic load at bearings BI and B2.

G,

pet
C)

a) Discuss Block brake with short shoe withfigure. 03

b) Discuss the working of Single Plate Clutch withfigure. 04
c) A multi-disk clutch consists of five steel plates and four bronze plates. The inner 07
and outerdiameters of the frictiondisks are 75 and 150 mm respectively.The
coefficient of friction is 0.1 and the intensity of pressure on friction lining is
limited to 0.3 N/mm2. Assuming uniform wear theory, calculate:
i) the required force to engage the clutch; and
ii) power transmitting capacity at 750 rpm

Page 4 of 16
T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
ViStrumentätionand Control Engineering (BTN02602)
Day & Date: Friday, 24-05-2024 Max. Marks: 70
Time: 03:00 PM To 06:00 PM
Instructions: 1) Q. No. 1 is compulsory. It should be solved in the first 30 minutes in
answer book Page no 03 (Starting page of the Answer Book). Each
question carries one mark.
2) Don't forget to Mentionquestion paper set (P/Q/R/S) on top of page.
3) Figures to the right indicates full marks.
4) Answer cannot be changed once it is marked.

MCQ/Objective Type Questions

Duration: 30 Minutes Marks: 14

Q.I Choose the correct answer: 14

I) Measurementof speed of a rotating shaft by an electric tachometer is a
a) primary measurement
b) non-contacttype measurement
c) secondary measurement
d) tertiarymeasurement
2) Which of the following metals is preferred in a resistance-thermometer
employed for measuring the temperature in the range -200 0C 10000C?
a) Platinum b) Copper
c) Nickel d) Tungsten
3) Which condition is essential in the operation of Mcleod gauge?
a) Isobaric b) Adiabatic
c) Isothermal d) Isochoric
4) A permanentmagnet is used in tachometer.
a) inductivepickup b) capacitive pickup
c) Mechanical d) photoelectricpickup
5) must be mounted vertically to use.
a) turbinemeter b) gas flow meter
c) Rotameter d) Anemometer
6) A Prony Brake dynamometermeasures the
a) Crank shaftforce b) Crank shafttorque
c) Engine Brake Power d) Power inputof Pump
7) A strain gauge converts Mechanical displacement in to change in
a) Inductance b) Resistance
c) Capacitance d) Reluctance
8) A comparatoris an essential featureof
a) manual system b) open loop system
c) any system d) feedback control system

Page 1 of 16

SLR-.JE-120
Set p
9) IntegralTime is given by
a) Kp/Ki b) Kp/Kd
C) Kd/Kp d) Ki/Kp
10) If error is constant, action gives a constant output.
a) P - action b) D- action
c) ON/OFF action d) I - action
11) A rootlocus has any branches originatingfrom infinitywhen

12) 'Centroid' of asymptotes is a point which

a) may be real or complex
b) is real but may or may not lie on the root locus
c) is real and always lies on the root locus
d) is always imaginary
13) 'Phase Margin' is always calculated at
a) Cornerfrequency b) Phase cross-overfrequency
c) Gain cross-over frequency d) Highest magnitude
14) If a system has two poles at the origin, its Magnitude Plot will have a
startingslope of
a) -20 db/decade b) - 40 db/decade
c) 20 db/decade d) 40 db/decade
 T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Instrumentation and Control Engineering (BTN02602)
Day & Date: Friday, 24-05-2024 Max. Marks: 56
Time: 03:00 PM To 06:00 PM
Instructions: I ) Solve any two questions from each Section.
2) Use of scientific calculator is allowed.
3) Figures to right indicate full marks.
4) Assume additional suitable data if necessary and state it clearly.
5) Use universitygraph paper and semi-log paper if required.

Section —I

Q.2 a) Explain following system characteristics. 04

1) Accuracy
2) dead zone
b) Explain with a neat sketch turbinetype flow meter. 06
c) Explain the basic principleof working of R.T.D. 04
Q.3 a) Describe with a neat skectch 'Mcleod gauge'. 06
b) Explain with a neat sketch 'stroboscope'. 04
c) Explain with a neat sketch 'Gear Train Dynamometer'. 04
Q.4 a) Derive 'the expression for voltage outputof Wheatstone's bridge circuit 06
using strain gauges.
b) A measuring system consists Ofa transducer, amplifierand recorder with 04
individual sensitivities as respectively,
kl = 0.25mV/'C,k2
= 2.5V/mV, = 4mm/V
Determine the overall sensitivity of this system.
c) Explain a hydraulic load cell. 04
Section — Il

Q.5 a) Differentiatebetween open loop and closed loop control systems. 04

b) For the block diagram of a feedback control system as shown in fig. (5-b), 06
obtain the closed loop transfer function C(S)/R(S)

c) Explain the 'MagnitudeCondition' in Root Locus and its importance. 04

Page 3 of 16

SLR-JE-120
set@
Q.6 a) For a controlsystem represented by, 09

Sketch the complete Root Locus and comment on the system stability.
b) Explain with a graph, P+D controller.What do you mean by 'Derivative 05
Time'?

Q.7 a) For a unity feedback control system given by, 09

200(S + 2)
¯ S2(S + 40)
Sketch the Bode Plots and comment on the system stability.
b) Explain Bode plots for simple poles & zeros. 05
 SLR-JE-121
Seat
No. Set p
T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Heat Transfer (BTN02603)
Day & Date: Monday, 27-05-2024 Max. Marks: 70
Time: 03:00 PM To 06:00 PM
Instructions: I) Q. No. I is compulsory. It should be solved in the first 30 minutes in
answer book Page no 03 (Starting page of the Answer Book). Each
question carries one mark.
2) Don't forget to Mentionquestion paper set (P/Q/R/S) on top of page.
3) Figures to the right indicates full marks.
4) Make suitable assumptions wherever necessary and state them clearly.

MCQ/Objective Type Questions

Duration: 30 Minutes Marks: 14

Q.l Choose the Correct answer. 14

I) When a composite wall of three layers in series having thermal resistances
RI, R2 and R3 respectively. The heat transfer takes place normal to the surface
of the layers. How is the totalthermal resistance of the composite system
calculated?
a) 1/(R1+ + R3) b) ((1/R1) + (1/R2) + (1/R3))
c) (RI + R2 + R3) d) None of the above
2) The critical radius of a hollowsphere having thermal conductivityk and ho
as convective heat transfer coefficient of outer fluid is given by
a) ho/k b) k/ho
c) 2k/ho d) ho/2k
3) In which of the followingcases most unsteady heat flow occurs?
a) Through the walls of a furnace
b) Through lagged pipes carrying steam
c) Through the wall of a refrigerator
d) During annealing of castings
4) What is the purpose of using fins in a particularheat transfer system?
a) To decrease rate of heat transfer
b) To increase rate of heat transfer
c) To maintain rate of heat transfer at a constant rate
d) cannot say
5) Aluminum is used as a fin material because
a) It has higher convection heat transfer coefficient
b) It has higher thermal conductivity
c) It has lower convection heat transfer coefficient
d) It has lower thermal conductivity
6) What is the relation between reflectivity (p), absorptivity(a) and
transmissivity
(r)?
c) p+a+t=l
Page 1 Of 16
 SLR-JE-121
set@
7) Unit of thermal diffusivity
a) m/s2 b) m2/s
c) J/s d) None of the above
body reflects entire radiation incident on it.
a) Transparent b) Black
c) Gray d) White
9) In a film condensation, the vertical plate temperatureshould be
a) More than the saturation temperature of the vapour
b) Less than the saturationtemperatureof the vapour
c) Equal to the saturationtemperatureof the vapour
d) None of the above
10) number is generally associated with only natural convection heat transfer.
a) Prandtl b) Weber
c) Nusselt d) Grashoff
The thickness of thermal boundary layer is equal to that of hydrodynamic
boundary layer when Prandtl number is
b) 0.1
c) 0.5 d) 1.0
12) An automobileradiatoris type of heat exchanger.
a) cross-flow b) regenerator
c) counter-flow d) recuperator
13) For the same heat transfer Q and, same overall, heat transfer coefficient
tJo, surface area required for counter flow operation is always
a) less than parallel flow b) more than parallel flow
c) same as parallel flow d) unpredictable
14) In parallelflow heat exchangers,
a) the exit temperatureof hot fluid is always equal to the exit temperature
of cold fluid
b) the exit temperatureof hotfluid is always less than the exit
temperature of cold fluid
c) the exit temperature of hot fluid is always more than the exit
temperature of cold fluid
d) we cannot predict comparison between exit temperatures of hot fluid
and cold fluid

Page 2 of 16
 SLR-JE-121
Seat
No. Set p
T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Heat Transfer (BTN02603)
Day & Date: Monday, 27-05-2024 Max. Marks: 56
Time: 03:00 PM To 06:00 PM
Instructions: I) Solve any two questions from each section.
2) Figures to the right indicate full marks.
3) Assume suitable data wherever necessary.
4) Use of scientific calculator is allowed.

Section —I

Q.2 Attempt the following questions.

a) Define thermal conductivity. Explain the effect of temperatureon thermal 04
conductivityfor solid, liquid and gases.
b) Derive the general heat conduction equation in three dimensions in Cartesian 05
coordinates.
c) A wall of a furnace is made up of inside layer of silica brick 120 mm thick 05
covered with layer of magnetite brick 240 mm thick. The temperatureat the
inside surface of silica brick wall and outside surface of magnetite brick wall are
7250C and 1 1OOCrespectively.The contact thermal resistance between the two
walls at the interface is 0.0035 Oclw per unit wall area. If thermal conductivities
of silica and magnetite bricks are I .7w/m0cand 5.8w/m0cCalculate
i) The rate of heat loss per unit area of walls, and
ii) The temperaturedrop at the interface

Q.3 Attempt the following questions.

a) Derive an expression for temperaturedistributionand heat flow rate for 04
infinitely long fin.
b) Find out the amountof heat transferred through an iron fin of length 50 mm 05
width 100 mm & thickness 5 mm Assume k=210 W/m oc & h =42 W/m20Cfor
the material of fin and the temperature and the base of fin 80 oc. Also
determine the temperature at the tip of fin when atmosphere temperature 20 oc
c) A small electrical heating application uses wire of 2mm diameter with 0.8 mm 05
thick insulation (k=O.12 W/m0C). The heat transfer coefficient on the insulation
surface is 35 W/m20C. Determine the critical thickness of insulationin this case
& the percentage change in the heat transfer rate if the critical thickness is
used. Assuming that the temperature difference between the surface of the
wire and surroundingair remains unchanged.

Q.4 Attempt the following questions.

a) Explain the following terms: 04
i) Solid angle.
ii) Radiosity.
Irradiation.

Page 3 Of 16
 SLR-JE-121
Set
b) State Plank's law of radiation.Hence derive Wien's displacement law. 05
c) Determine the rate of heat loss by radiationfrom a steel tube of outside 05
diameter 70 mm and 3 m long at the temperatureof 227 0C. If the tube is
located in a square brick conduit of 0.3 m side and 27 'C. Take = 0.79 &
= 0.93
E(briCk)
Section —Il

Q.5 Attempt the following question.

a) Show by dimensional analysis, Nu = f(Gr.Pr) for naturalconvection. 04
b) Explain with neat sketch velocity and thermal boundary layer. 05
c) The Crankcase of an l.c. Engine measuring 80cm x 20 cm may be idealized 05
as a flat plate. The engine runs at 90 Km/hr & the crankcase is cooled by the
air flowing past it at the same speed. Calculate the heat loss from the crank
surface maintainedat 850C to the ambientair at 15 'C. Due
to road induced vibrationthe boundary layer becomes turbulentfrom the
leading edge itself.
The Properties of air at 50 0C are:
K = 0.02824w/m oc,y = 17.95x 10-6m/s2,Pr = 0.698
Use

Q.6 Attempt the following questions.

a) Define Condensation and explain its types. 04
b) Draw typical pool boiling curve and explain various regimes of pool boiling. 05
c) A counter flow double pipe heat exchanger using hot water at the rate Of 10500 05
kg/h. the steam enters the heat exchanger at 1800C & leaves at 1300C .
The inlet & exit temperaturesof water are 300C and 800C resp. if overall heat
transfer coefficient from steam to water is 814 W/m20C.Calculate the heat
transfer area. What would be the increase in area if fluid flow were parallel.
Take specific heat of water 4.187 KJ/Kg K.

Q.7 Attempt the following questions.

a) Explain Heat Pipe working and its applications. 04
b) Derive an expression for determiningthe LMTD of parallel flow heat 05
exchanger.
c) A chemical having specific heat of 3.3 KJ/KgK flowing at the rate Of 20000 05
Kg/hr. enters the parallel flow heat exchanger at 1200C. The flow rate of
cooling water is 50000 Kg/hr having specific heat of 4.186 KJ/KgK with an inlet
temperature20 0C. The heat transfer area is 10 m2 and the overall heat transfer
coefficient is 1050 W/m2K.
Find:
i) The effectiveness of heat exchanger
ii) The outlettemperatureof water and chemical

Page 4 of 16
 T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Industrial & Quality Management (BTN02604)
Day & Date: Wednesday, 29-05-2024 Max. Marks: 70
Time: 03:00 PM To 06:00 PM
Instructions: 1) Q. No. 1 is compulsory and should be solved in first 30 minutes in Answer
Book Page No.3 (starting page of the Answer Book). Each question
carry one mark.
2) Don't forget to mention Question Paper Set (PIQ/R/S) at the top of the
same page.
3) Draw neat-labelled diagrams wherever necessary.
4) Figures to right indicate full marks.
5) Use of log table and calculators is allowed.

MCQ/ObjectiveType Questions
Duration: 30 Minutes Marks: 14

Q.I Choose the correct option from the following. 14

1) is defined as "the discipline dealing with what is good & bad & with
moral duty & obligation".
a) Rule b) Organisation culture
c) Protocol d) Ethics
2) Managers are the real 'team manager' in grid type
a) 1.9 b) 5.5
c) 9.1 d) 9.9
3) In concept productenjoys the supreme importance.
a) Selling b) Marketing
c) Manufacturing d) Business
4) Close control, close supervision is advantage of
a) Narrow span b) Wide span
c) Close span d) Open span
5) The responsibilitiesof the operations manager include
a) Planning, organizing, staffing, procuring and reviewing
b) Forecasting, designing, planning, organizing, and controlling
c) Forecasting, designing operating, procuring, and reviewing
d) Planning, organizing, staffing, leading, and controlling
e) Designing & operating
6) Self esteem, status affiliationWithothers, affection those come under
needs.
a) Basic b) Primary
c) Third level of d) Secondary
7) is abilityof individualor group to induce or influence the beliefs or
action of other person or group.
a) Power b) Authority
c) Post d) Leadership

Page 1 Of16

SLR-JE-122
Set p
8) The basic objective of qualitycontrol in any organisation is to
a) Quality development, quality maintenance and quality improvement
activities in organization
b) Achieve optimumcost
c) Achieve customer's satisfaction
d) Achieve all the above
9) Cost associated with defective products being shipped to the customers
are called as
a) Cost of internalfailure b) Total cost of failure
c) Rejection cost d) Cost of external failure
10) For identificationof vital few for the given data, the tool used is
a) Cause-Effect diagram b) Scatter diagram
c) Pareto Analysis d) Check Sheet
11) Total quality management (TQM) mainly aims for
a) Control for quality b) Usefulness of product
c) Customer satisfaction d) Cost control
12) The statistician who invented the control chart for use in industrial quality
control was:
a) Deming b) Taguchi
c) Pareto d) Shewhart
e) None of the above
13) The methodof accepting or rejecting the lot is known as
a) Lot sampling b) Acceptance sampling
c) Batch sampling d) Quality control
14) In double sampling plan, second sample is taken when the number of
defectives
a) but
c) and C2
 T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Industrial & Quality Management (BTN02604)
Day & Date: Wednesday, 29-05-2024 Max. Marks: 56
Time: 03:00 PM To 06:00 PM
Instructions: 1) Question no. 3 is compulsory in section l, and solve any two questions
from the remaining. (Q. No. 2, 4 & 5)
2) Question no. 6 is compulsory in section Il, and solve any two questions
from the remaining. (Q. No. 7, 8 & 9)
3) Figures to the right indicate full marks.
4) Draw neat-labelled diagrams wherever necessary.
5) Use of log table and calculators is allowed

Section —I

Q.2 a) What are managerial skills and managerial roles? 05

b) Explain the financial management role, nature & functions of each 04
department.

Q.3 a) What is planning? Explain advantages and disadvantages of planning? 05

b) What are the types of organizations? Explain Problems with organizational 05
level.

Q.4 a) Define Leadership. Explain four extreme styles. 05

b) Discuss types of communication by taking suitable example. 04

Q.5 Write short note on (Any Three) 09

a) Channel of distribution
b) Social responsibilitiesin management.
c) Methods of Departmentation
d) Explain Maslow's theory
e) Decision making

Section —Il

Q.6 a) What is meaning of qualityof design and qualityof conformance? Explain 05

the factors affecting quality of design.
b) Differentiate between: Cost of quality & value of quality. 05

Q.7 a) How employee involvementaffects organization performance? What are 05

various ways to improve employee involvement?
b) List seven quality controltools. Explain with neat sketches Pareto analysis, 04
Scatter diagram and cause and effect diagram.

Page 3 of 16

SLR-JE-122
Set p
Q8 a) A manufacturerpurchases small bolts in cartons that usually contain several 05
thousand bolts. Each shipment consists of a number of cartons. As a part of
acceptance procedure for these bolts 400 bolts are selected at random from
each carton and are subjected to visual inspection for certain defects. In
shipment 10 cartons the respective percentage of defectives in the sample
from each carton are O, O, 0.5, 0.75, O, 2.0, 0.25, O, 0.25 and 1.25. Does this
shipment of bolts appear to exhibit statistical controlwith respect to the
quality characteristics examined in the inspection?
b) Explain actual and ideal OC curve for a sampling plan. Also explain all 04
concepts such as producer's risk, consumer's risk.

Q.9 Write short note on (Any Three) 09

a) Need of Environment management system
b) Supplier partnership
c) Appraisal costs and Prevention costs
d) X bar chart
e) Six Sigma.
 SLR-JE-123
Seat
No. Set p
T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Project Management (BTN02608)
Day & Date: Friday, 31-05-2024 Max. Marks: 70
Time: 03:00 PM To 06:00 PM
Instructions: 1) Q. No. I is compulsory. It should be solved in the first 30 minutes in
answer book Page no 03 (Starting page of the Answer Book). Each
question carries one mark.
2) Don't forget to Mentionquestion paper set (P/Q/R/S) on top of page.
3) Figures to the right indicates full marks.
4) Make Suitable assumptions wherever necessary and state them clearly.

MCQ/ObjectiveType Questions
Duration: 30 Minutes Marks: 14

Q.I Choose the correct alternatives from the options. 14

I) Project is a endeavor.
a) Temporary b) Permanent
c) Perpetual d) None of the above
2) Which from the following represents the correct project cycle?
a) Planning —iInitiating—YExecuting —iClosing
b) Planning —iExecuting —iInitiating-9 Closing
c) Initiating—i Planning Executing —iClosing
d) Initiating-+ Executing -i Planning -i Closing
3) Which stage of project management life cycle requires the maximum time
of completion
a) Conceptualization b) Planning
c) Execution d) Estimation
4) What file extension is used for Microsoft Project files?
a) .mpp b) .mpd
c) ,mcm d) ,pct
5) Fill in the blank. There is correlation between project complexity
and project risk. Select one:
a) an unknown b) a positive
c) no d) a negative
6) The cash inflows and (outflows) associated with a project are as follows: At start
(120000), Year 1: 40000, Year 2: 50000. Year 3: 60000, Residual Value (at the
end of 3rd year): 20000. The payback period for this project would be:
a) 2 years and 3 months b) 2 years and 6 months
c) 3 years d) 2 years
7) Which of the following represents the estimated value of the work actually
accomplished?
a) Earned value (EV) b) Planned value (PV)
c) Actual cost (AC) d) Cost variance(CV)

Page 1 of 16
 SLR-JE-123
set@
8) A company is considering investing surplus funds in a project. Calculate
the NPV at 7 % discount rate for the following data:
Pro ect Year O Year 1 Year 2
A 200 200 200
a) 161.60 b) 1.6160
c) 16.160 d) 200
9) From the following calculate critical Path Duration in days
Activity: 1-2 2-3 2-4 3-5 4-6 5-6
Duration: 34 3 3 22
a) 13 days b) 8 days
c) Il days d) 12days
10) The probabilityof completing the project can be estimated based upon
the
a) Uniform distributioncurve b) Exponential distributioncurve
c) I-I-shaped distributioncurve d) Normal distributioncurve
11) With respect to PERT and CPM, slack
a) is a task or subproject that must be completed
b) marks the start or completion of a task
c) is the latest time an activity can be started withoutdelaying the entire
project.
d) is the amount of time a task may be delayed withoutchanging the
overall project completion time.
12) Scheduling used to determine:
a) overall project duration
b) project cost estimating
c) the project management plan
d) sub-contractor's responsibilities
13) A communication management plan identifies the relevant informationthat
should be communicated to:
a) the project team b) the project stakeholders
c) the project board d) the project sponsor
14) For an activity in a CPM analysis, the early Finish time is 13 and the late Finish
time is 13, Duration of activity is 6. Which of the following statements is true?
a) The early start is 6
b) The duration of the activity is 13
c) The slack of this activity is 13
d) The activity is on the critical path

Page 2 of 16
 T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April-2024
MECHANICAL ENGINEERING
Project Management (BTN02608)
Day & Date: Friday, 31-05-2024 Max. Marks: 56
Time: 03:00 PM To 06:00 PM
Instructions: 1) Solve any two questions from each Section
2) Figures to the right indicates full marks.

Section —I

Q.2 a) Explain role of Project Manager. 05

b) Explain the phases of a project life cycle 05
c) State various numerical/financial models used in project feasibility study. 04
Explain NPV.
Q.3 a) Explain break even analysis with its importance in project management. 05
b) What are scoring models? Explain weighted scoring model in project 05
selection
c) Explain project feasibility studies. 04

Q.4 a) State the various project cost-estimating methods. Explain any one 05
methods in detail.
b) What is risk management? Explain steps in risk management. 05
c) Write a short note on Monte Carlo Simulation. 04
Section — Il

Q.5 a) Explain Purpose of Project Execution and Control. 05

b) An R & D project has a list of tasks to be performed whose time estimates 05
are given in the Table as follows.
i) Draw the project network.
ii) Find the critical path.
Activity Activity Name

1-2 4 6 8
1-3 2 3 10
1-4 c 6 8 16
2-4 1
2 3
6 7 8
3-5 7 6 14
4-6 5 3 7
4-7 4 11 12
5-7 2 4 6
6-7 2 9 10
c) Explain CPM and PERT. How they are different from each other? 04

Page 3 of 16

SLR-JE-123
Set
Q.6 a) What is Project Controlling? Explain various steps in Project Control 05
Process.
b) Write a short note on Work Breakdown Structure (WBS) 05
c) Explain Project Management InformationSystem (PMIS) 04
Q.7 a) Explain importance of Project Performance measurement. Explain Benefits 05
and Challenges of Performance Measurement and Evaluation.
b) Explain Resource levelling and smoothing with example. 05
c) Write a short note on Use of MS Projects in Project Management. 04
 T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April - 2024
MECHANICAL ENGINEERING
Battery Technology and Charging Infrastructure (BTN02615)
Day & Date: Monday, 03-06-2024 Max. Marks: 70
Time: 03:00 PM To 06:00 PM
Instructions: 1) Q. No. 1 is compulsory. It should be solved in the first 30 minutes in
answerbook. Page no 03 (Startingpage of the Answer Book). Each
question carries one mark.
2) Don't forget to Mentionquestion paper set (P/Q/R/S) on top of page.
3) Figures to the right indicates full marks.

MCQ/ObjectiveType Questions
Duration: 30 Minutes Marks: 14

Q.' Choose the correct answer: 14

1) Number of cells connected in series provide a
a) High current carrying capacity b) Higher Voltage
c) Higher power d) None of the above
2) Battery container should be acid resistance therefore it is made up of
a) Glass b) Plastic
c) Wood d) All of the above
3) the best indication of the state of charge of a battery.
a) Temperature of electrolyte b) Specific gravity of electrolyte
c) Level of electrolyte d) Colour of electrolyte
4) avoids the direct contact of the positive and negative plate in a
lithium-ion battery?
a) Electrolyte b) Separator
c) Load d) Rectifier
5) Which is the electrolyte used in Li-ion battery?
a) Lead dioxide b) Lithium-basedgel
c) Sulfur dioxide d) Cobalt
6) Battery is a device which converts chemical energy into
a) Mechanical energy b) potentialenergy
c) Electrical energy d) Wind energy
7) It is noticed that during charging
a) There is a rise in voltage
b) Energy is absorbed by the cell
c) Specific gravityof H2S04 is increased
d) All of the above
8) Overcharging
a) Produces excessive gassing
b) Loosens the active material
c) Increases the temperature resulting in buckling of plates
d) All of the above

Page 1 of 12

SLR-JE-130
Set p
9) The capacity of a battery is expressed in terms of
a) Current rating b) Voltage rating
c) Ampere hour rating d) None of the above
10) Each cell has a vent cap
a) To allow gases out when the cell is on charge
b) To add water to the cell if needed
c) To check the level of electrolyte
d) To do all above functions
11) Cell short circuit results in
a) Low specific gravityelectrolyte b) Abnormalhigh-temperature
c) Reduced gassing on charge d) All of the above
12) Internal resistance of a cell is reduced to by
a) Using vent plug to permitgas formed during discharge
b) Increasing the plate area
c) Putting plates very close together
d) All of the above
13) Which of the following circuit is used for cooling of the lithium-ionbattery?
a) Air conditioning b) Heater circuit
c) Ignitioncircuit d) EGR circuit
14) Which of the following is not an advantage of Lithium-ion battery?
a) High specific energy density b) More expensive
c) Reliability d) Lower self-discharge rate
 SLR-JE-130
Seat
No. Set p
T.Y. (B.Tech.) (Sem - Il) (New) (CBCS) Examination: March/April - 2024
MECHANICAL ENGINEERING
Battery Technology and Charging Infrastructure (BTN02615)
Day & Date: Monday, 03-06-2024 Max. Marks: 56
Time: 03:00 PM To 06:00 PM
Instructions: I) Answer any 2 questions from each section.
2) Figures to the right indicates full marks.

Section —I

Q.2 Solve the following.

a) Define the following: 07
i) State of charge
ii) C-Rate
iii) Specific Energy Density
iv) Life cycles
v) Depth of Discharge
vi) Usable capacity
vii) Energy capacity
b) Explain parameters for EV battery selection. 07

Q.3 Solve the following.

a) Explain I-MO and I-TO battery chemistries. 07
b) Explain various cell failures. 07

Q.4 Solve the following.

a) Explain Lithium-Polymer battery with neat sketch. 07
b) Explain Lithium-air battery with neat sketch. 07

Section — Il

Q.5 Solve the following.

a) Explain forces acting on battery pack with neat sketch. 07
b) Explain Battery Pack Development Process. 07

Q.6 Solve the following.

a) Explain the battery management system. 07
b) Explain why thermal management of battery pack is important? 07

Q.7 Solve the following.

a) Explain differentEV Charging protocols. 07
b) Explain on-board, off-board chargers and slow and fast chargers. 07

page 3 of 12