User manual SURECOM SF-103

1.1 Power On / Off:

Power on, press and Hold down the [Red key] by 3 second
Power off, press and Hold down the [Red key] by 3 second of number count
down to 0

1.2 Charging the battery:

Plug the power cord into adaptor, micro usb connect SF-103
The Led indicating: *The RED light Charging, * The Green light is Full

1.3 Setup the frequency Range:

Press [F2 stop] button, [F3 -->] select function to "Range"
Press the [F4 Ent] Select 27 MHz -2.8 GHz (27 MHz – 2800 MHz) / <= 200
MHz (below 200 MHz),
and then press [F2] to Run

1.4 Setup the time Gate:

Press [F2 stop] button, [F3 --->] select Function to "Gate"
Press the [F4 Ent] select: 0.1s / 0.25s / 0.5s / 1.0 s, and then press [F2] to Run

1.5 Setup the Frequency counter digital:

Press [F2] button, [F3--->] select Function to "Gate"
Press [F4 Ent] Select: 3 / 4 / 5 / 6, and then press [F2] to Run
27 MHz - 2.8 GHz for 3 / 4 only, 2 – 200 MHz for 3 / 4 / 5 / 6, Detail Please see
Table 1.

1.6 How to check Frequency of Digital DMR Radio

Press [F2] button, [F3 --->] select Function to" type": Press [F4] select Analog
/ Digital (DMR),
and then Press [F2] to Run
! Note. Digital mode have 3 Decimal only.
1.7 How to ADJ the Frequency mode of 27 MHz - 2.8 GHz:
Press, [F3 MENU], [F3 Down] / [F4 Up] to select the Gate to (0.1 s / 0.25 s /
0.5 s / 1.0 s)
Press, [F2 Edit] / [F3 - ] and [ F4 +] to select the +/- 99
Press, [F1 Main] exit, and then press [F4 save] for save the setting ([F1] not
save for exit)

1.8 How to fine tune the Frequency mode of 2 – 200 MHz:

Tune the PCB VR1 (Variable resistance)
(The factory has been set accurate, such as non-technical staff do not tune)

1.9 How to use [F3 menu] mode:

Press, [F3 -] / [F4 +] select the function, and then press [F2 edit] for edit mode,
Press, [F3 -] / [F4 +] select for change the data.
Press, [F1 Main] exit, and then press [F4 save] for save the setting ([F1] not
save for exit)

Caution:
1. Max. direct input signal 5Vp-p
2. Prohibit direct access to the radio antenna output, resulting in damage to the
frequency meter
 Table 1: Frequency Display Resolution / CTCSS, DCS Decode frequency range

Gate Time Sample Display (100 MHz) CTCSS/DCS

select Digital select A
(seconds) 3 4 5 6
SELECT Decode
27 MHz -
0.10 s 100.000 100.0000 Range
A 2.8 GHz
0.25 s 100.000 100.0000 132-173MHz
0.50 s 100.000 100.0000 200-260MHz
400-519MHz
1.00 s 100.000 100.0000

Gate Time Sample Display (100 MHz) CTCSS/DCS

select Digital select B
(seconds) 3 4 5 6
SELECT 2 MHz –
0.10 s 100.000 100.0000
B 200 MHz
0.25 s 100.000 100.0000 Disable
0.5 s 100.000 100.0000 100.00000 100.000000
1.00 s 100.000 100.0000 100.00000 100.000000

How to check CTCSS/DCS code:

1. Radio must be 132-173 / 200 – 260 MHz / 400 – 519 MHz
2. Radio must be ANALOG
Table 2: CTCSS/DCS Decoder for ANALOG mode

CTCSS (Hz)
50.0 97.4 151.4 192.8
55.0 100.0 156.7 196.6
67.0 103.5 159.8 199.5
69.3 107.2 162.2 203.5
71.9 110.9 165.5 206.5
74.4 114.8 167.9 210.7
77.0 118.8 171.3 218.1
79.7 123.0 173.8 225.7
82.5 127.3 177.3 229.1
85.4 131.8 179.9 233.6
88.5 136.5 183.5 241.8
91.5 141.3 186.2 250.3
94.8 146.2 189.9 254.1
 Table 3: CDCSS for ANALOG mode (N code only)

sf103 sf103 sf103 sf103

Standard(N) Standard(N) Standard(N) Standard(N)
check check check check
23 23 143 143 266 465 465
25 25 145 271 271 466 466
26 26 152 152 274 503 503
31 31 155 155 306 306 506 506
32 32 156 156 311 311 516 516
36 162 162 315 315 532 532
43 43 165 165 325 546 546
47 47 172 172 331 331 565 565
51 51 174 174 332 606 606
53 205 205 343 343 612 612
54 54 212 346 346 624 624
65 65 223 223 351 351 627 627
71 71 225 356 631 631
72 72 226 226 364 364 632 632
73 73 243 243 365 365 654 654
74 74 244 244 371 371 662 662
114 114 245 245 411 411 664 664
115 115 246 412 412 703 703
116 116 251 251 413 413 712 712
122 252 423 423 723 723
125 125 255 431 431 731 731
131 131 261 261 432 432 732 732
132 132 263 263 445 445 734 734
134 134 265 265 464 464 743 743
754 754