SAMARPAN ACADEMY

A Professional Coaching for Civil Engineering

Test 02 : RCC + PSC(PWD + WRD)
Total : 125 , Time :2.15 Hrs.
Maxmimum Marks : 125 Negative:¼ Marks

Q. 1. Which of the following statement Q. 5. What happened with the neutral

is/are correct?? axis in the under reinforced section, if
(i) Long term modulus of elasticity load furhter increased after yeilding of
of concrete is based on secent steel
modulus (A) Remains at its original position
(ii) Short term modulus of elsticity (B) Shifts downwards
considered effect of creep also (C) Shifts upwards
(iii) Creep coefficent defined as the (D) Coincides with critical nuetral
ration of ultimate strain to axis
elastic strain
(A) Only (i) correct Q.6. Assertion (A): critical section for
(B) Only (ii) correct shear at a distance “d” from face of
(C) Only (iii) correct the column if suppors are under
(D) All are correct compression
Reason (R) At simply supported beam
Q. 2. A prestressed concrete section is said shear foece is minimum at supports
to have failed in strength at the (A) Both A and R are true and R is
moment when all the the material in the correct explanation of A.
the section has exhausted its (B) Both A and R are true and R is
(A) stress limitations not the correct explanation of A.
(B) strain limitations (C) A is true and R is false
(C) load limitations (D) R is true and A is false
(D) stress as well as strain limitations
Q. 7. Which of the following statement
Design of prestressing member it is/are correct?
assumed that member fail if both the 1. Xu,max depands only grade of
the stress and strain in the concrete concrete
exceed their permissible limit. 2. Maximum shear strength of
concrete depands only grade of
Q. 3. The minimum percentage of mild steel
steel reinforcement to be provided in (A) Only 1 correct
any direction in a retaining wall is? (B)Only 2 correct
(A) 0.12 (C) Both correct
(B) 0.15 (D) None of the above
(C) 0.17
(D) 0.20
Q. 8. Shrinkage crack in RCC slab can
Q. 4. Which of the following losses of appear due to
prestress occurs only in pre- (A) Improper curing
tensioning and not in post-tensioning (B)Improper loading
(A) elastic shortening of concrete (C) Improper formwork
(B) shrinkage of concrete (D) Improper mixing of concrete
(C) creep of concrete
(D) loss due to friction Q. 9. For M20 grade of concrete
maximum Quantity of Water per
5O kg of Cement is?
(A) 28 litre

Contact No.- 6261378731, 7995878403 Page 1

 (B)30 litre moment
(C) 32 litre Q. 15. The reinforcement shall be placed
(D) 34 liter within the following tolerances as
per IS456-2000 :?
Q. 10. The unsupported length of a 1. for effective depth 200 mm or
reinforced concrete column shall be less is ± 10mm
(A) Sixty times the least cross- 2. for effective depth more than 200
sectional dimension mm or more is ± 15mm
(B)Double to effective length of select the correct answer using
column the codes given below.
(C) Clear distance between end (A) Only 1 correct
restraints (B)Only 2 correct
(D) Same as the effective length (C) Both 1 and 2 correct
(D) None oh these
Q. 11. Consider the following statements.
1. If slab supportes all the edge is Q. 16. In limit state of collapse for flexure,
called as two way slab if aspact the tensile strength of concrete is
ratio is greater than 2 (A) To be considered same as
2. If slab supportes on opposite side compressive strength
only is called as one way slab if (B)0.42 times the compressive
aspact ratio is less than 2 strength
Which of the above statements is/are (C) To be ignored
correct? (D) Partially considered
(A) 1 only
(B)2 only Q. 17. Drops are provided in a Flat Slab to
(C) Both 1 and 2 resist
(D) None of these (A) Bending moment
(B)Shear
Q. 12. The development length in a bar (C) Compression
used in reinforced concrete is for (D) Torsion
(A) Tension reinforcement only
(B) Compression reinforcement only Q. 18. Effective length of a column
(C) Both (A) and (B) effectively held in position at both
(D) Shear reinforcement only ends but not restrained against
rotation is
(A) 0.8 × unsupported length
Q. 13. Curtailment of bars can be made (B)0.65 × unsupported length
from the distance beyond the point (C) 1.2 × unsupported length
there is no flexure load to resist (D) Same as unsupported length
equal to
(A) Effective depth of the member Q. 19. The horizontal distance between
(B)12 times the bar diameter two parallel main bars shall not be
(C) Minimum of (A) or (B) less than the following :
(D) Greater of (A) or (B) (A) Diameter of bars if bars are of
same diameter
Q. 14. In an interior span of flat slab, the (B)Diameter of larger bar is
negative design moment is taken as diameters are unequal
(A) 0.50 times the total design (C) 5 mm more than nominal
moment maximum size of coarse
(B)0.65 times the total design aggregate
moment (D) All the above
(C) 0.70 times the total design
moment
(D) 0.40 times the total design

Contact No.- 6261378731, 7995878403 Page 2

Q. 20. As per IS : 456-2000 What is the List-I
recommended length of column for A. Organic
effctive held in position at one end B. Inorganic
but not restrained aqainst rotation, C. Sulphates
and at the other end ratntined D. Suspended matter
against rotion but not held in List-II
position 1. 200 mg/l
(a) L 2. 3000 mg/l
(b)1.2 L 3. 400mg/l
(c) 1.5 L 4. 2000mg/l
(d)2.0 L
(a) 1 2 3 4
Q. 21. Consider the following statements : (b) 1 2 4 3
In an under-reinforced concrete (c) 4 3 2 1
beam. (d) 4 2 1 3
(1) Actual depth of neutral axis is
less than the critical depth of Q. 25. In the case of lap joints, the
neutral axis. minimum lap should NOT be
(2) Concrete reaches ultimate stress _______ times the thick- ness of the
prior to steel reaching the thinner part joined, or 40
ultimate stress. mm,whichever is more.
(3) Moment of resistamce is less than (a) More than three
that of balanced sections. (b)Less than four
(4) Lever arm of resisting couple is (c) Less than three
less than that of balanced (d)Less than two
sections.
Which of the statements given above Q. 26. If design bond stress = 1.5 N/mm2 is
are correct ? as-sumed, then the development
length of an Fe 500 HYSD bar of
(a) 1 and 2 nominal diameter 12mm - which is
(b) 1 and 3 fully stressed in tension -will be:
(c) 2, 3 and 4 (a) 544 mm
(d) 1 and 4 (b)246 mm
(c) 634 mm
Q. 22. The striping time for the Reinforced (d)798 mm
Concrete slab spanning less than 4.5
m and using fly ash as an admixture Q.27 Consider the following statements
should be with respect to Bundles of bars
(a) 7 days 1 For 2 bars development length
(b) 10 days 10% increases
(c) 14 days 2 For 3 bars development length
(d) 21 days 20% increases
3 For 4 bars development length
Q. 23. Creep of concrete is 33% increases
(a) Deformation due to sudden load Which of the statements given
(b) Deformation due to seismic load above is/are Correct?
(c) Shrinkage due to temperature (a) 1 and 2
(d) Deformation due to sustained (b)1 and 3
load (c) 2 and 2
(d)1, 2 and 3
Q. 24. Match List-I(compounds ) with List
II (permissible limit of solid) and Q. 28. In counterfort retaining walls, the
select the correct answer using the main reinforcement in the stem at
code given below the lists :- support i

Contact No.- 6261378731, 7995878403 Page 3

 (A) Not provided List-I
(B)Provided only on inner face A. For RCC construction maximum
(C) Provided only on front face size of coarse aggregate
(D) Provided both on inner and B. Minimum dia of main
front face reinforcement for column
C. Clear cover for beam
Q. 29. Consider the following statements D. Clear cover for slab
regarding the slabs: List-II
1. When the longer span to shorter 1. 20 mm
span ratio is greater than or equal to 2. 25 mm
two, it is a two-way slab. 3. 12 mm
2.In one-way slab, the load transfer (a) 2 1 3 1
is chiefly by bending in the shorter (b)1 3 2 1
direction. (c) 2 3 1 1
3. In two-way slabs, the load (d)1 2 3 1
transferred by bending in both
orthogonal directions.
Which of the above statements is/are Q. 33. In prestressed concrete:
correct? (a) Forces of tension and
(a) 1 and 2 only compression change but lever
(b)3 only arm remains unchanged
(c) 2 and 3 only (b)Forces of tension and
(d)1 and 3 only compression remain un-changed
but lever arm changes with the
Q. 30. As per IS : 456 - 2000, the range of mo-ment
standard concrete is (c) Both forces of tension and
(a) M25 - M60 compression and lever arm
(b)M20 - M55 changes
(c) M25 - M50 (d)Both forces of tension and
(d)None of these compression and lever arm
remain unchanged
Q. 31. Consider the following statements.
1. For deformed bars conforming to Q. 34. Limit state of serviceability for
IS1786 these values shall be deflection including the effects due
increased by 60 percent to creep, shrinkage and temperature
2. For bars in compression. the occurring after erection of partitions
values of bond stress for bars in and application of finishes as
tension shall be increased by 25 applicable to floors and roofs is
percent (a) Span/150
3. The anchorage value of bend (b)Span/200
shall be taken as 4 times the (c) Span/250
diameter of the bar for each 45⁰ (d)Span/350
bend subject to a maximum of 16
times the diameter of the bar Q. 35. Match List-I(environment )with List
Which of the above statements are II(exposure condition) and select the
correct?? correct answer using the code given
(a) 1and 2 only below the lists :-
(b)2 and 3 only List-I
(c) 1 and 3 only A. Mild
(d)1, 2 and 3 B. Moderate
C. Severe
Q. 32. Match List-I with List II and select D. Extreme
the correct answer using the code List-II
given below the lists :- 1. Concrete continuosily under

Contact No.- 6261378731, 7995878403 Page 4

 water Q. 38. A rectangular 230 mm × 350 mm
2. Members in direct contact with beam is (effective depth). The
solid aggrasive chemicals factored shear force acting at a
3. Concrete surface protected section is 80 kN. If the permissible
against waether shear stress in concrete is 0·25 MPa,
4. Concerte exposed to coastal the design shear force is nearly
environment
A B C D (a) 100 kN
(a) 4 1 3 2 (b)80 kN
(b) 3 1 4 2 (c) 60kN
(c) 3 4 1 2 (d)20 kN
(d) 4 3 2 1
Q. 39. Which one of the following section
Q. 36. Consider the following statements. gives an economical design?
1. For main reinforcement up to (a) Balanced section
12mm diameter bar for mild (b) Under reinforced section
exposure the nominal cover (c) Over reinforced section
may be reducedby 5 mm (d) Prismatic section
2. For exposurecondition'severe'
and 'very severe'. reduction Q. 40. Which of the following statements is
of 5 mm may be made where NOT correct?
grade of concrete is M35 and (a) As the grade of concrete
above increases, its tensile strength also
Which of the statements given increases.
above is/are Correct? (b) As the grade of concrete
(a) 1 only increases, its modulus of elasticity
(b) 2 only also increases.
(c) 1 and 2 (c) For a given grade of concrete and
(d) None of these size, cube strength test results are
more than that of cylinder
strength test results.
Q.37. Match List-I(Placing condition)with (d) As the size of the concrete cube
List II(slump value) and select the increases, the strength results also
correct answer using the code given increase.
below the lists :-
List-I Q. 41. The member subjected to torsion
A. Trench fi1l shall be designed for fictitious shear
B. Heavily reinforced sections in which is function of the actual shear
slab and torsion?
C. Pumped concrete (a) Critical shear
D. Light reinforcement section in (b) Equivalent shear
slab (c) Theorotical shear
List-II (d) Design shear
1. 50-100
2. 100-150 Q. 42. Match List-I with List II and select
3. 75-100 the correct answer using the code
4. 25-75 given below the lists :-
List-I
A B C D A. Servicibility
(a) 3 2 1 4 B. Shear key
(b) 3 4 2 1 C. Shrinkage
(c) 2 3 4 1 D. Concrete spalling
(d)2 1 3 4 List-II
1. Sliding

Contact No.- 6261378731, 7995878403 Page 5

 2. Deflection Q. 48. In RCC beam main reinforcement
3. Craking consists of 16 mm and coarse
4. Corrosion aggregate size used is 20mm. The
horizontal distance between two
(a) 1 3 4 2 parallel reinforcing bar should not
(b)2 1 3 4 be less
(c) 1 3 2 4 (a) 16 mm
(d)2 1 4 3 (b) 20 mm
(c) 25 mm
Q. 43. In a two way slab with corners held (d) 18 mm
down, the torsion steel is provided at
the Q. 49. The length of the straight portion of
(a) Top the bar beyond the end of the hook
(b) Bottom should be atieast
(c) Both top & bottom (A) Twice the diameter
(d) Middle (B)Thrice the diameter
(C) Four times the diameter
Q.44. A 300 x 300 mm RC column is (D) Seven times the diameter
reinforced with eight bars. Four
bars are of 12 mm dia and four of 10 Q. 50. Main reinforcement in the staircase
mm dia. The diameter of lateral ties slab supported between two stringer
is 6 mm. The pitch of lateral ties beams is arranged
shall be kept as (A) parallel to the width of flight &
(a) 300 mm at the bottom of the slab
(b) 192 mm (B)parallel to the width of flight &
(c) 160 mm at the top of slab
(d) 288 mm (C) parallel to the length of flight &
at the bottom of slab
Q. 45. The shear reinforcement in RCC is (D) parallel to the length of flight &
provided to resist at the top of slab
(a) diagonal tension
(b) diagonal compression Q. 51. When shear stress exceeds the
(c) horizontal shear permissible limit in a slab, then it is
(d) vertical shear reduced by?
(a) Increasing the depth
Q. 46. The width of the flanghe of a T- (b) providing the shear
bean should be less than reinforcement
(a) One-third of the effective span of (c) Using the high strength of steel
the T-beam (d) Using thinner bar but more in
(b) The distance between the centre number
of the T-beam
(c) The breadth of the rib plus twelve Q. 52. Near the mid span of the beam the
times the thickness of the slab crack are?
(d) Least of the above (a) Inclined at 60°
(b) Inclined at 45°
Q. 47. A short RCC column is designed (c) Vertical 90°
assum-ing maximum permissible (d) Horizontal
axial compres- sive stresses in
concrete and steel as : Q. 53. What is the diameter of the column
(a) 0.4 fck and 0.67 fy respectively head supporting a flat slab?
(b) 0.446 fck and 0.87 fy respectively (a) 0.25 times the span
(c) 0.67 fck and 0.67 fy respectively (b) 2.5 times the diameter of column
(d) 0.446 fck and 0.67 fy Respectively (c) 4 times the diameters of the
column

Contact No.- 6261378731, 7995878403 Page 6

 (d) 0.5 times the diameter of the to obtain the descending portion of
column stress and strain curve beyond
maximum stress.
Q. 54. According to IS 456:1978 , the (A) Both A and R are true and R is
the correct explanation of A.
compressive stress in steel should (B) Both A and R are true and R is
be calculated by multiplying the not the correct explanation of A.
stress in the surrounding (C) A is true and R is false
(D) R is true and A is false
concrete by
(a) 1.05 times the modular ratio
(b) 1.50 times the modular ratio
(c) 2.0 times the modular ratio
Q. 60. Assertion (A): Shear capacity of a
(d) 3.0 times the modular ratio
concrete beam increases with the
increase in tension reinforcement.
Q. 55. Diagonal tension reinforcement is
Reason (R): Increase in tension
provided in a beam as?
reinforcement increases aggregate
(a) Longitudinal bar
interlocking force.
(b) Bent up bar and vertical stirupps
(A) Both A and R are true and R is
(c) helical reinforcement
the correct explanation of A.
(d) 90° bend at the bend of main bar
(B) Both A and R are true and R is
not the correct explanation of A.
Q. 56. Which of the following losses is a
(C) A is true and R is false
Time-dependent loss in prestressed
(D) R is true and A is false
concrete?
(a) Elastic Shortening
Q. 61. Consider the following statements.
(b) Steel Relaxation
1. A beam shall be deemed to be a
(c) Anchorage Slip
deep beam when the ratio of
(d) Friction
effective span to overall depth.
is less than 2 for a continuous
Q. 57. Which of the following types of
beam.
panel has Maximum Positive
2. A beam shall be deemed to be a
Moment at mid-span for the same
deep beam when the ratio of
loading conditions and ly/lx ratio of
effective span to overall depth.
1.5?
is less than 2.5 for a simly
(a) One short edge discontinuous
supportes beam.
(b) One short edge continuous
Which of the above statements is/are
(c) One long edge discontinuous
correct?
(d) One long edge continuous
(a) Only 1
Q. 58. For RC braced frames maximum
(b) Only
redistribution is not allowed in
(c) Both 1 and 2
(a) indeterminate beam
(d) None
(b) determinate beam
(c) indeterminate and determinate
Q. 62. Which one of the following is
(d) None of theses
correct?
Fully prestressed concrete beams
Q. 59. Assertion (A): The stress block used
(a) resist all the working loads by
in the limit state design method is
prestress
obtained by testing of concrete
(b)resist the full live load by
cylinder under uniform rate of strain.
prestress
(c) resist the part of the load by
Reason (R): If a uniform rate of
prestress
strain is not adopted it is not possible

Contact No.- 6261378731, 7995878403 Page 7

 (d)resist only the dead loads (a) Forces of tension and
compression change but
Q. 63. match List – I with List – II and lever arm remains unchanged
selecty the correct answer by using (b)Forces of tension and
the codes given below this lists: compression remain
List-I unchanged but lever arm
A. In flexure compression of changes with the moment
concrete the maximum design (c) Both forces of tension and
stress as per IS compression and lever arm
B. In flexure compression, the remain unchanged
maximum stress in the (d)Both forces of tension and
characteristic curve of concrete compression and lever arm
as per the IS changes

List-II Q. 68. Shrinkage deflection in case of

1. 0.67 Fck rectangular beams and slabs can be
2. 0.447 Fck eliminated by putting
Codes:- (e) Compression steel equal to
(A) 2 1 tensile steel
(B) 2 2 (f) Compression steel more than
(C)1 1 tensile steel
(D)1 2 (g) Compression steel less than
tensile steel
Q. 64. As per IS : 456-2000 the acceptable (h)Compression steel 25% more
limits of crack-width for concrete than tensile steel
structures exposed to mild and
moderate exposure categories or Q. 69. High tensile strength bars threaded
conditions are at the ends are used in
(a) 0.3 mm and 0.3 mm respectively
(b) 0.2 mm and 0.3 mm respectively (a) Freyssinet system
(c) 0.3 mm and 0.2 mm respectively (b) Gifford Udall system
(d) 0.15 mm and 0.5 mm respectively (c) Magnel-balton system
(d) Lee-MeCall system
Q. 65. According to IS 456 clause 13.5.1
The period of curing of concrete Q. 70. In a post-tension pre-stressed
depends on : concrete beam, the end block zone is
(a) Coarse aggregates in between the end of the beam and
(b)Density of cement the section where
(c) Fine aggregates (A) The shear stresses are maximum
(d)Type of cement used (B)Only shear stresses exist
(C) No lateral stresses exist
Q. 66. The minimum and maximum (D) Only longitudinal stresses exist
longitudinal reinforcement in an
RCC column of size 300 mm x500
mm when the bars are lapped is Q. 71. The lap length of direct tension
Minimum at the beginning and reinforcement bar in a Rcc beam
maximum at the end should be more than
(a) 180 mm2 and 6000 mm2
(b)1200 mm2 and 9000 mm2 (a) twice the development length or
(c) 1200 mm2 and 6000 mm2 30 time the diameter of the bar
(d)1800 mm2 and 6000 mm2 whichever is lesser
(b)the development length or 30
Q. 67. In prestressed concrete:? times the diameter of the bar
whichever is lesser

Contact No.- 6261378731, 7995878403 Page 8

 (c) the development length or 24 (C) A is true and R is false
times the diameter of the bar . (D) R is true and A is false
whichever is greater
(d)twice the development length or Q. 77. Consider the following statements
30 time the diameter of the bar with regard to crack formation and
whichever is greater its control
1. The surface width of the crack
Q. 72. In an under reinforcement concrete should not, in general, exceed 0.30
beam mm for structures not subjected to
(a) Moment of resistance is less than that of aggressive environment
balance sections 2. When depth of web in a beam
(b) Actual depth of neutral axis is more exceeds 750 mm, side face
than the critical depth of neutral axis reinforcement @ 0.1 percent of web
(c) Both above options are corret area should be provided on each
(d) None of these face.
3. The nominal spacing of main bars
Q. 73. Which one of the following in a slab should not exceed three
represents minimum requirements times the effective depth of a solid
of reinforcement in a RC slab for slab or 300 mm, whichever is
deformed bars? smaller.
(b) 0.12%
(c) 0.15% Which of the statements give above
(d) 0.17% is/are correct?
(e) 0.20% (a) 1 only
(b)1 and 3
Q. 74. According to working stress method (c) 1 and 2
the limiting value of permissible (d)2 and 3
tensile stresses for a reinforced
concrete member in tension for Q. 78. Assertion (A): The working stress
HYSD grade Fe 415 is: method of R.C.C. design of beams is
(A) 190 also known as modular ratio method.
(B)230 Reason (R): The ratio of stress in
(C) 250 steel and concrete is the same as that
(D) 415 of elastic moduli of steel and concrete
in beam
Q. 75. The modular ratio of M 25 grade of
concrete if ϭ-cbc = 8.5 MPa. (A) Both A and R are true and R is
(a) 10.98 the correct explanation of A.
(b) 11.98 (B) Both A and R are true and R is
(c) 12.98 not the correct explanation of A.
(d) 13.98 (C) A is true and R is false
(D) R is true and A is false
Q. 76. Assertion (A) : The provision of
lateral reinforcement in RCC
Q. 79. Select the correct statement with
columns is not mandatory.
respect to an over-reinforced
Reason (R): The lateral cement concrete section under
reinforcement in RCC columns helps the working stress method.
in preventing possible buckling of (A) The compressive steress in steel
longitudinal reinforcement. reaches the allowable limit
(A) Both A and R are true and R is before the maximum tensile stres
the correct explanation of A. in concrete reaches the allowable
(B) Both A and R are true and R is limit
not the correct explanation of A. (B)Tensile steel stress and maximum

Contact No.- 6261378731, 7995878403 Page 9

 compressive stress in concrete (C) A is true and R is false
simultaneously reach their (D) R is true and A is false
allowable limits.
(C) The allowable limiting is reched Q. 84. The thickness of the flange of a tee
in concrete before the steel stress beam of a ribbed slab is assumed as
reaches the limiting value (a) Width of the rib
(D) The tensile stress in steel reaches (b)Depth of the rib
the allowable limit before the (c) Thickness of the concrete
maximum compressive strss in topping
concrete reaches the allowable (d)Half the thickness of the rib
limit.
Q. 85. At what stress does the first
Q. 80. When a RCC beam is subjected to
flexural crack appear in RCC beams
twisting moment torsion
made of M25 grade concrete?
reinforcement is provided as :
(A) Tension reinforcement (a) 3.0 MPa
(B)Shear reinforcement only (b) 3.5 MPa
(C) Shear and flexural (c) 4.5 Mpa
reinforcement
(D) Flexural reinforcement only (d) 4.0 MPa

Q. 81. shrinkage in concrete slab : Q. 86. Limit state of serviceability of

(A) causes shear cracks prestressed concrete sections should
(B)causes tension cracks satisfy
(C) causes compression cracks (a) Cracking, deflection and
(D) does not cause any cracking maximum compression
(b)Cracking only
Q. 82. for a slab to act as T-beam or L- (c) Deflectin and cracking
beam, if the main reinforcement of (d)Deflection and maximum
the slab is parallel to the beam, the compression
minimum transverse reinforcement
required is Q. 87. What is the purpose of
(A) 30% of the main reinforcement reinforcement in prestressed
of mid span of the slab concrete?
(B)40% of the main reinforcement (a) To provide adequate bond stress
of mid span of the slab (b) To resist tensile stresses
(C) 50% of the main reinforcement (c) To impart initial compressive
of mid span of the slab stress in concrete
(D) 60% of the main reinforcement (d) All of these
of mid span of the slab
Q. 88. The maximum free water-cement ratio
Q. 83. Assertion (A): At horizontal curve for the concrete used in tidal zone is:
psychological widening is provided (a) 0.55
Reason (R): At horizontal curve, (b) 0.50
drivers have the tendency to maintain (c) 0.45
a greater clearance between the (d) 0.40
vehicles, than a straight stretch of
road. Therefore, an extra width is Q. 89. Consider the following statements.
required for this. Serviceability limit in Limit state
(A) Both A and R are true and R is method deals with which of the
the correct explanation of A. following is/are correct
(B) Both A and R are true and R is 1. Compression
not the correct explanation of A. 2. Flexure
3. Deflection
Contact No.- 6261378731, 7995878403 Page 10
 4. Shear (c) 1.4 times the lap length
(d) 1.8 times the lap length
(a) 1 and 2only
(b) 3 only Q.96. Shear reinforcement is required to
(c) 1, 2 and 3 prevent propagation of
(d) all (a) Flexural crack
(b) Diagonal cracks
Q. 90. Modular ratio in WSM is:? (c) Dowel crack
(A) Modulus of elasticity of steel to (d) Splitting crack
that of modulus of elasticity of
concrete Q. 97. The horizontal distance between
(B)Modulus of elasticity of concrete parallel reinforcement bars
2. to that of modulus of elasticity provided against shrinkage and
of steel temperature shall not be more than
(C) Strain in steel to that of strain in (a) 3 times the effective depth of
concrete solid slab or 300 mm whichever is
(D) Stress in concrete to that of less
stress in steel (b) 3 times the effective depth of solid
slab or 450 mm whichever is less
Q. 91. The maximum spacing of spiral (c) 5 times the effective depth of solid
tie is mm.? slab or 300 mm whichever is less
(A) 75 mm (d) 5 times the effective depth of solid
(B)25 mm slab or 450 mm whichever is less
(C) 100 mm
(D) 300 mm Q. 98. The splicing of a column
becomes necessary, where
Q. 92. Tension bar in cantilever beam must (a) The available length of structural
be in enclosed in the support up to? steel section is less than the
(A) LD/3 required length of the column.
(B)LD (b) Section remains same throughout at
(C) 12φ all floors
(D) D (c) Only riveted columns are to be
designed
Q.93. A flat slab supported on
(d) Splices should be designed to carry
(a) Beam
axial loads only.
(b) Column
(c) Beam or Column
Q. 99. In the case of a continuous RC
(d) Column monolithically build with
beam, in order to obtain the
slab
maximum positive span moment,
where should the live load be
Q.94. When shear stress exceeds the
placed?
permissible limit in a slab, then it is
(a) On all the spans
reduced by
(b) On alternate spans starting from
(a) Increasing the depth
the left
(b) providing the shear reinforcement
(c) Using the high strength of steel
(c) On spans adjacent to the spans
(d) Using thinner bar but more in
under consideration
number
(d) On the span plus alternate spans
Q. 95. Lap spliced shall be considered if
Q.100. If the load acting on a commonly
the c/c distance is not less than
conventional sized RC column
(a) 1.2 times the lap length
(b) 1.3 times the lap length increases continuously from zero

Contact No.- 6261378731, 7995878403 Page 11

 to higher magnitudes, the (c) By reducing the refresh rate
magnitude of the uniaxial (d) By transferring data on both the
rising and falling edges of the clock
ultimate moment that can be
signal
allowed on the column
(a) Increases (a) Navigation Keys
(b) Decreases (b) Special Purpose Keys
(c) Increases and then decreases (c) unction Keys
(d) Remains constant (d) Toggle Keys

Q.101 Listed below are some operating Q.105 What is Full Form of BIOS?
system abstractions (list 1) and the (a) Basic Investment/Output system
hardware components (list 2)? (b)Basic In/ out system
(c) Basic Input/Output system
List 1 (d) Basic Input/Output Station
(A) Thread
(B) Virtual address space Q.106. Look at this series: 7, 10, 8, 11, 9, 12,
(C) File system ... What number should come next?
(D) Signal (A) 6
List 2 (B) 10
1. Interrupt (C) 12
3. Memory (D) 13
1. CPU This is a simple alternating addition
2. DIsk and subtraction series. In the first
pattern, 3 is added; in the second, 2
(a) 1. A-2, B-4, C-3, D-1 is subtracted.
(b) A-1, B-2, C-3, D-4
(c) A-3, B-2, C-4, D-1 Q.107. Find the missing series?
(d) A-4, B-1, C-2, D-3 2978,?, 746, 374, 188,95
(A) 1490
Q.102 Main Goal of Operating System is to (B)1230
provide the Interface between:? (C) 1550
(a) user and the hardware (D) 6340
(b) software and hardware
(c) program and memory Q.108. Find the missing series?
(d) main memory and user ?,154, 147, 136, 123, 106
(a) 159
Q.103 How does DDR RAM achieve double (b) 160
the data transfer rate compared to (c) 132
SDRAM? (d) 154
(a) By increasing the clock frequency
(b) By using a wider data bus Q.109. Find out the wrong term in the
(c) By reducing the refresh rate series 2, 3, 4, 4, 6, 8, 9, 12, 16?
(d) By transferring data on both the (A) 8
rising and falling edges of the clock (B)9
signal (C) 12
(D) 18
Q. 104. The keyboard keys like Caps lock
that turn on features on or off are Q.110. Look at this series: 8, 22, 8, 28, 8, ...
called How does DDR RAM achieve What number should come next??
double the data transfer rate (a) 24
compared to SDRAM? (b) 29
(a) By increasing the clock frequency (c) 32
(b) By using a wider data bus (d) 34

Contact No.- 6261378731, 7995878403 Page 12

 state governors by the center has
Q.111. Look at this series: 7, 10, 8, 11, 9, 12, been taken from the constitution of
... What number should come next? which country?
(A) 7 (A) अमेररका
(B)10 (B)आयरलैंड
(C) 12
(C) किाडा
(D) 13
(D) ऑस्ट्रे नलया

Q.112. Look carefully for the pattern, and Q.117. यह भारत के सोंनवधाि में निम्ननलक्तित में
then choose which pair of numbers कहाों उक्तिक्तित है ?
comes next. India, which is Bharat, will be a
8, 12, 9 ,13 ,10, 14 ,11 union of states."
(A) 14 ,11 Where is it mentioned in the
(B)15,12 Constitution of India in the
(C) 8,15 following?
(D) 15,19 (A) प्रस्ताविा
(B)अिु च्छेद 1
Q.113. Given a Series (C) अिु च्छेद 2
1, 30, 5, 26, 9, 22, 13, 18, ?
(D) दू सरी अिु सूची
Find what number would come in
place of the question mark(?).
Q.118. सयिािाि सोंस्तर की चट्टािें नकस रूप
a) 17 में है ?
b) 22 (A) डाइक
c) 28 (B) नसल
d) 196 (C) नसट
(D) साइिाट
Q.114. Find the number that will come in
the place of the question mark in the
given series
4, 18, ?, 100, 180, 294, 448. Q.119. निम्ननलक्तित में से कौि-सी सीमा
a) 62 छत्तीसगढ़ के पहाडी इलाकयों का नहस्सा
b) 86 िही ों है ?
c) 38 (A) सतपुडा पवव तमाला
d) 48 (B)नवों ध्याचल पवव तमाला
(C) अरावली पवव तमाला
(D) मैकल पवव तमाला
Q.115. Find the number which would come
in place of question mark Q.120. इस राज् के प्राकृनतक नवभागयों में
81 : 101 :: 121 : ? . निम्ननलक्तित में से कौि-सा सक्तिनलत
िही ों है ?
a) 141 (A) पूवी बघेलिण्ड का पठार
b) 143 (B)महािदी बेनसि
c) 170
(C) दण्डकारण्य का पठार
d) 145
(D) दक्कि का पठार
Q.116. राज्यों के राज्पालयों की केंद्र द्वारा
Q. 121. छत्तीसगढ़ में ककव रे िा निम्नाोंनकत में
नियुक्ति का प्रावधाि नकस दे श के
से नकस निला से हयकर गुिरती है ?
सोंनवधाि से नलया गया है ?
(A) रायपुर निला
The provision of appointment of (B)नबलासपुर निला

Contact No.- 6261378731, 7995878403 Page 13

 (C) कयरबा निला
(D) सूरिपुर निला

Q. 122. छत्तीसगढ़ राज् प्रतीक नचह्न में

शानमल िही ों है ?
(A) अशयक स्तम्भ
(B)सत्यमेव ियते
(C) साल वृ क्ष
(D) धाि की सुिहरी बानलयााँ

Q. 123. कयटमी सयिार क्यों प्रनसद्ध है ?

(A) भालू सोंरक्षण के नलए

(B)मगरमच्छ सोंरक्षण के नलए
(C) पहाडी मैिा सोंरक्षण के नलए
(D) वि भैंसा सोंरक्षण के नलए

Q. 124. निम्ननलक्तित में से कौि-सा छत्तीसगढ़

का बहुमूल्य िनिि िही ों है ?
(A) अलेक्जेण्डराइट
(B)ग्रेिाइट
(C) हीरा
(D) गारिे ट

Q. 125. छत्तीसगढ़ की मैकल श्रेणी की

पहानडययों में सबसे ऊोंची चयटी कौि-सी
है ?
(A) दे वगढ़
(B) बदरगढ़
(C) लाफागढ़
(D) रायगढ़

Contact No.- 6261378731, 7995878403 Page 14