CCMT 0602 r

80º
CCMT 09T3 r
80º

D D

7º 7º
I s I s

Dimensions Dimensions
Designation Grade Designation Grade
I D s r I D s r
CCMT 060204-UF YG801 5.94 6.35 2.38 0.4 CCMT 09T304-UF YG801 9.25 9.53 3.97 0.4

CCMT 060208-UG YG801 5.44 6.35 2.38 0.8 CCMT 09T308-UG YG801 8.85 9.53 3.97 0.8

CCMT 060204 Recommended Cutting Condition CCMT 09T304 Recommended Cutting Condition

Material Cutting Conditions Material Cutting Conditions

Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm) Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm)
Group Sub Group Group Sub Group
(HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend (HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend

Non Alloys 120 0.08 0.20 0.14 180 330 300 0.2 2.1 1.0 Non Alloys 120 0.11 0.23 0.17 180 330 300 0.2 3.0 2.0

P Low Alloys 200 0.08 0.17 0.13 120 280 250 0.2 1.8 1.0 P Low Alloys 200 0.10 0.20 0.15 120 280 250 0.2 2.5 2.0

High Alloys 220 0.07 0.15 0.11 70 190 170 0.2 1.8 1.0 High Alloys 220 0.09 0.18 0.14 70 190 170 0.2 2.5 2.0

M Austenitic 190 0.08 0.15 0.12 170 270 250 0.2 1.8 1.0 M Austenitic 190 0.10 0.18 0.14 170 270 250 0.2 2.5 2.0

K Grey Cast Iron 140 0.06 0.17 0.12 170 250 240 0.2 2.1 1.0 K Grey Cast Iron 140 0.08 0.20 0.14 170 250 240 0.2 3.0 2.0
Heat Resistant Heat Resistant
S and Super Alloys 240 0.08 0.13 0.07 25 50 35 0.2 1.4 1.0 S and Super Alloys 240 0.09 0.15 0.12 25 50 35 0.2 2.0 2.0

H Hardened Materials 45HRc 0.04 0.10 0.07 50 100 75 0.2 1.3 0.8 H Hardened Materials 45HRc 0.05 0.12 0.09 50 100 75 0.2 1.8 1.5

CCMT 060208 Recommended Cutting Condition CCMT 09T308 Recommended Cutting Condition

Material Cutting Conditions Material Cutting Conditions

Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm) Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm)
Group Sub Group Group Sub Group
(HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend (HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend

Non Alloys 120 0.08 0.20 0.14 180 330 250 0.4 2.1 1.2 Non Alloys 120 0.21 0.50 0.36 180 330 255 0.5 5.0 3.0

P Low Alloys 200 0.08 0.17 0.13 120 280 200 0.4 1.8 1.2 P Low Alloys 200 0.21 0.45 0.33 120 280 200 0.5 5.0 3.0

High Alloys 220 0.07 0.15 0.11 70 190 130 0.4 1.8 1.2 High Alloys 220 0.18 0.40 0.29 70 190 130 0.5 4.0 2.5

M Austenitic 190 0.08 0.15 0.12 170 270 200 0.4 1.8 1.2 M Austenitic 190 0.20 0.40 0.30 170 270 220 0.5 5.0 3.0

K Grey Cast Iron 140 0.06 0.17 0.12 170 250 210 0.4 2.1 1.2 K Grey Cast Iron 140 0.15 0.60 0.38 170 250 210 0.5 5.0 3.0
Heat Resistant Heat Resistant
S and Super Alloys 240 0.08 0.13 0.07 25 50 30 0.4 1.4 1.2 S and Super Alloys 240 0.20 0.35 0.28 25 45 35 0.5 3.0 2.0

H Hardened Materials 45HRc 0.04 0.10 0.07 50 100 75 0.4 1.3 0.8 H Hardened Materials 45HRc 0.11 0.30 0.21 50 100 75 0.5 2.5 2.0

94 www.yg1.kr www.yg1.kr 95
CCMT 0602 r
80º
CCMT 09T3 r
80º

D D

7º 7º
I s I s

Dimensions Dimensions
Designation Grade Designation Grade
I D s r I D s r
CCMT 060204-UF YG801 5.94 6.35 2.38 0.4 CCMT 09T304-UF YG801 9.25 9.53 3.97 0.4

CCMT 060208-UG YG801 5.44 6.35 2.38 0.8 CCMT 09T308-UG YG801 8.85 9.53 3.97 0.8

CCMT 060204 Recommended Cutting Condition CCMT 09T304 Recommended Cutting Condition

Material Cutting Conditions Material Cutting Conditions

Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm) Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm)
Group Sub Group Group Sub Group
(HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend (HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend

Non Alloys 120 0.08 0.20 0.14 180 330 300 0.2 2.1 1.0 Non Alloys 120 0.11 0.23 0.17 180 330 300 0.2 3.0 2.0

P Low Alloys 200 0.08 0.17 0.13 120 280 250 0.2 1.8 1.0 P Low Alloys 200 0.10 0.20 0.15 120 280 250 0.2 2.5 2.0

High Alloys 220 0.07 0.15 0.11 70 190 170 0.2 1.8 1.0 High Alloys 220 0.09 0.18 0.14 70 190 170 0.2 2.5 2.0

M Austenitic 190 0.08 0.15 0.12 170 270 250 0.2 1.8 1.0 M Austenitic 190 0.10 0.18 0.14 170 270 250 0.2 2.5 2.0

K Grey Cast Iron 140 0.06 0.17 0.12 170 250 240 0.2 2.1 1.0 K Grey Cast Iron 140 0.08 0.20 0.14 170 250 240 0.2 3.0 2.0
Heat Resistant Heat Resistant
S and Super Alloys 240 0.08 0.13 0.07 25 50 35 0.2 1.4 1.0 S and Super Alloys 240 0.09 0.15 0.12 25 50 35 0.2 2.0 2.0

H Hardened Materials 45HRc 0.04 0.10 0.07 50 100 75 0.2 1.3 0.8 H Hardened Materials 45HRc 0.05 0.12 0.09 50 100 75 0.2 1.8 1.5

CCMT 060208 Recommended Cutting Condition CCMT 09T308 Recommended Cutting Condition

Material Cutting Conditions Material Cutting Conditions

Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm) Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm)
Group Sub Group Group Sub Group
(HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend (HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend

Non Alloys 120 0.08 0.20 0.14 180 330 250 0.4 2.1 1.2 Non Alloys 120 0.21 0.50 0.36 180 330 255 0.5 5.0 3.0

P Low Alloys 200 0.08 0.17 0.13 120 280 200 0.4 1.8 1.2 P Low Alloys 200 0.21 0.45 0.33 120 280 200 0.5 5.0 3.0

High Alloys 220 0.07 0.15 0.11 70 190 130 0.4 1.8 1.2 High Alloys 220 0.18 0.40 0.29 70 190 130 0.5 4.0 2.5

M Austenitic 190 0.08 0.15 0.12 170 270 200 0.4 1.8 1.2 M Austenitic 190 0.20 0.40 0.30 170 270 220 0.5 5.0 3.0

K Grey Cast Iron 140 0.06 0.17 0.12 170 250 210 0.4 2.1 1.2 K Grey Cast Iron 140 0.15 0.60 0.38 170 250 210 0.5 5.0 3.0
Heat Resistant Heat Resistant
S and Super Alloys 240 0.08 0.13 0.07 25 50 30 0.4 1.4 1.2 S and Super Alloys 240 0.20 0.35 0.28 25 45 35 0.5 3.0 2.0

H Hardened Materials 45HRc 0.04 0.10 0.07 50 100 75 0.4 1.3 0.8 H Hardened Materials 45HRc 0.11 0.30 0.21 50 100 75 0.5 2.5 2.0

94 www.yg1.kr www.yg1.kr 95
CCMT 1204 DCMT 0702
r
80º r

D D

7º
7º 55º s
I
I s

Dimensions Dimensions
Designation Grade Designation Grade
I D s r I D s r
CCMT 120408-UG YG801 11.88 12.70 4.76 0.8 DCMT 070204-UF YG801 7.38 6.35 2.38 0.4

CCMT 120408 Recommended Cutting Condition DCMT 070204 Recommended Cutting Condition

Material Cutting Conditions Material Cutting Conditions

Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm) Hardness Feed (mm/rev.) Vc (m/min.) Depth Of Cut (mm)
Group Sub Group Group Sub Group
(HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend (HB) Min. Max. Recommend Min. Max. Recommend Min. Max. Recommend

Non Alloys 120 0.21 0.50 0.36 180 330 255 0.5 5.0 3.0 Non Alloys 120 0.08 0.20 0.14 180 330 300 0.2 2.1 1.0

P Low Alloys 200 0.21 0.45 0.33 120 280 200 0.5 5.0 3.0 P Low Alloys 200 0.08 0.17 0.13 120 280 250 0.2 1.8 1.0

High Alloys 220 0.18 0.40 0.29 70 190 130 0.5 4.0 2.5 High Alloys 220 0.07 0.15 0.11 70 190 170 0.2 1.8 1.0

M Austenitic 190 0.20 0.40 0.30 170 270 200 0.5 5.0 3.0 M Austenitic 190 0.08 0.15 0.12 170 270 250 0.2 1.8 1.0

K Grey Cast Iron 140 0.15 0.60 0.38 170 250 210 0.5 5.0 3.0 K Grey Cast Iron 140 0.06 0.17 0.12 170 250 240 0.2 2.1 1.0

Heat Resistant Heat Resistant

S and Super Alloys 240 0.20 0.35 0.28 25 45 35 0.5 3.0 2.0 S and Super Alloys 240 0.08 0.13 0.11 25 50 35 0.2 1.4 1.0

H Hardened Materials 45HRc 0.11 0.30 0.21 50 100 75 0.5 2.5 2.0 H Hardened Materials 45HRc 0.04 0.10 0.07 50 100 75 0.2 1.3 0.8

96 www.yg1.kr www.yg1.kr 97
 UNIVERSAL GRADES

Features of Grades :
YG-1 Universal grades, designs for multi-purpose application and extremely efficient
in covering materials including Steels, Stainless Steels and Cast Iron.

YG602
Exclusive PVD coating / Unique Substrate
for MILLING and DRILLING Application

Optimal PVD Coating for t Ultra dense PVD coating with optimal thermal resistance & added strength
Milling and Drilling t Sub-micron substrate designed for demanding application
application

Micro grain size carbide

YG801
Exclusive PVD coating / Unique Substrate
for TURNING Application
Optimal PVD Coating for
Turning application
t Unique PVD coating and substrate designed to balance edge strength
& wear resistance for continuous machining.
t Excellent cutting performance under harsh machining condition.

Micro grain size carbide INDEXABLE CUTTING TOOLS

YG UNIVERSAL LINE

YG1001
Unique Substrate / CVD coating
for TURNING Application
Optimal CVD Coating for
Turning application
t Thick coating optimized
for Cast iron applications and
harsh machining condition.
t Advanced CVD coating with optimal thermal & wear resistance
for turning applications.
t Exceptional cutting performance attributed to combination of
carbide substrate and coating.
Unique substrate

Grade P M K S
YG602 P30-40 M20-30 K20-30 S10-20

YG801 P20-40 M20-40 K10-25 S05-25

YG1001 - - K10-25 -

6 www.yg1.kr www.yg1.kr 7
 TURNING INSERTS DESIGNATION SYSTEM (ISO) TURNING INSERTS DESIGNATION SYSTEM (ISO)

C N M G 12 04 08 CHIP
BREAKER

1 2 3 4 5 6 7 8

1 120°
5 C D S R T V W H
85° 82° 80° 55° 75° 55°
Insert Cutting I.C.
Shape Edge Size
A B C D E H K L
Length
135° 108°
80° Special Metric
3.97 03 04 03 03 06 02
O P R S T W X
4.76 04 05 04 04 08 08
5.56 05 06 05 05 09 09 03
2 6.35 06 07 06 06 11 11 04
5° 7° 15° 20° 25° 30° 0° 11°
Clearance 7.94 08 09 07 07 13 13 05
Angle α B C D E F G N P 9.525 09 11 09 09 16 16 06
12.7 12 15 12 12 22 22 08 05
3 Tolerance I.C. Size 15.875 16 19 15 15 27 27 10 09
19.05 19 23 19 19 33 33 13 10
Tolerance m t I.C. 6.35 9.525 12.7 15.875 19.05 25.4
25.4 25 31 25 25 44 44 17
A ± 0.005 ± 0.025 ± 0.025 ● ● ● ● ● ●
*( ) symbol for small size insert
C ± 0.013 ± 0.025 ± 0.025 ● ● ● ● ● ●

E ± 0.025 ± 0.025 ± 0.025 ● ● ● ● ● ● 6 7 8

F ± 0.005 ± 0.025 ± 0.013 ● ● ● ● ● ● Thickness Nose Radius Chip Breaker
G ± 0.025 ± 0.13 ± 0.025 ● ● ● ● ● ●

H ± 0.013 ± 0.025 ± 0.013 ● ● ● ● ● ●

For Application
± 0.05 ● ●
Symbol(t) mm Symbol(r) mm
± 0.08 ● 02 2.38 02 0.2
K ± 0.013 ± 0.025
± 0.10 ● ● 03 3.18 04 0.4
± 0.13 ● T3 3.97 08 0.8
04 4.76 10 1.0
± 0.18 ± 0.05 ● ●
06 6.35 12 1.2
± .0050 ± 0.08 ●
07 7.94 16 1.6
M ± 0.13
± .0060 ± 0.10 ● ● 09 9.52 20 2.0
± .0070 ± 0.13 ●

YG Turn Chip Breakers

Depth (mm)
Application area 6.0 For Roughing Application
m
m m UR

I.C. I.C. t
I.C. UG
For General Application
1.5 UF
4 1.0
Special 0.5
Cross C'Sink40°~ 60° C'Sink40°~ 60° For Finishing Application
Section
A F G M N R T W X
Shape 0.05 0.1 0.2 0.7
Feed (mm/rev.)

70 www.yg1.kr www.yg1.kr 71
 TURNING INSERTS DESIGNATION SYSTEM (ISO) TURNING INSERTS DESIGNATION SYSTEM (ISO)

C N M G 12 04 08 CHIP
BREAKER

1 2 3 4 5 6 7 8

1 120°
5 C D S R T V W H
85° 82° 80° 55° 75° 55°
Insert Cutting I.C.
Shape Edge Size
A B C D E H K L
Length
135° 108°
80° Special Metric
3.97 03 04 03 03 06 02
O P R S T W X
4.76 04 05 04 04 08 08
5.56 05 06 05 05 09 09 03
2 6.35 06 07 06 06 11 11 04
5° 7° 15° 20° 25° 30° 0° 11°
Clearance 7.94 08 09 07 07 13 13 05
Angle α B C D E F G N P 9.525 09 11 09 09 16 16 06
12.7 12 15 12 12 22 22 08 05
3 Tolerance I.C. Size 15.875 16 19 15 15 27 27 10 09
19.05 19 23 19 19 33 33 13 10
Tolerance m t I.C. 6.35 9.525 12.7 15.875 19.05 25.4
25.4 25 31 25 25 44 44 17
A ± 0.005 ± 0.025 ± 0.025 ● ● ● ● ● ●
*( ) symbol for small size insert
C ± 0.013 ± 0.025 ± 0.025 ● ● ● ● ● ●

E ± 0.025 ± 0.025 ± 0.025 ● ● ● ● ● ● 6 7 8

F ± 0.005 ± 0.025 ± 0.013 ● ● ● ● ● ● Thickness Nose Radius Chip Breaker
G ± 0.025 ± 0.13 ± 0.025 ● ● ● ● ● ●

H ± 0.013 ± 0.025 ± 0.013 ● ● ● ● ● ●

For Application
± 0.05 ● ●
Symbol(t) mm Symbol(r) mm
± 0.08 ● 02 2.38 02 0.2
K ± 0.013 ± 0.025
± 0.10 ● ● 03 3.18 04 0.4
± 0.13 ● T3 3.97 08 0.8
04 4.76 10 1.0
± 0.18 ± 0.05 ● ●
06 6.35 12 1.2
± .0050 ± 0.08 ●
07 7.94 16 1.6
M ± 0.13
± .0060 ± 0.10 ● ● 09 9.52 20 2.0
± .0070 ± 0.13 ●

YG Turn Chip Breakers

Depth (mm)
Application area 6.0 For Roughing Application
m
m m UR

I.C. I.C. t
I.C. UG
For General Application
1.5 UF
4 1.0
Special 0.5
Cross C'Sink40°~ 60° C'Sink40°~ 60° For Finishing Application
Section
A F G M N R T W X
Shape 0.05 0.1 0.2 0.7
Feed (mm/rev.)

70 www.yg1.kr www.yg1.kr 71