Scribd
Upload
26 views3 pages

senographe-600ts

The document provides technical measurements and observations related to the PL3 and C809826 circuit boards, indicating operational voltages and LED statuses. It mentions the absence of a specific motor (M821) and confirms that all fuses and the power supply are functioning correctly. Additionally, there are discussions about connecting a laptop to the seno 600T hf system for adjustments, with responses offering guidance on the connection process and software availability.

Uploaded by

Luis Fernando Garcia S
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
26 views3 pages

senographe-600ts

The document provides technical measurements and observations related to the PL3 and C809826 circuit boards, indicating operational voltages and LED statuses. It mentions the absence of a specific motor (M821) and confirms that all fuses and the power supply are functioning correctly. Additionally, there are discussions about connecting a laptop to the seno 600T hf system for adjustments, with responses offering guidance on the connection process and software availability.

Uploaded by

Luis Fernando Garcia S
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Vue de la façade d’affichage

Platine PL3 N° C
800047

Je mesure sur la platine PL3 les tensions suivantes :

PT11 = 12,17 V

Led DE2 = allumée (jaune)

Led DE3 = éteinte (rouge)

PT8 = 0V (Masse)

PT 14 = 12,17 V

PT 12 = 0,512 V

PT 4 = 10,97 V

Led DE4 = allumée (jaune)

Platine C809826 Vue arrière du


commutateur de KV

La platine C809826 est reliée à la platine 45439849 via le


connecteur X3

J’aimerais te signaler kil n’existe pas de moteur M821 dans


l’appareil, le seul moteur qui existe est le moteur de montée
et descente de la colonne. Il fonctionne correctement.

Tous les fusibles sont bons, voir les photos ci dessous


Bloc des fusibles supérieur Bloc des fusibles
inferieurs

Vue d’ensemble supérieur Vue d’ensemble


inferieur

Bloc d’alimentation +/-


12 V fonctionne
correctement.

seno 600T hf
by Tayfun Canli on November 07, 2003
Hi to all,
i need to adjust PM gain on seno 600T hf, but i don't have
information about how to connect laptop to seno. I have seno
service terminal software ver 1.16. Please show me the way...
Thanks..
[ Reply to This ]

Re: seno 600T hf


by Manuel Casanova on November 09, 2003
In response to: Tayfun Canli
Tayfun:
Connect the serial cable in senographe jack XJ33 on the back
panel PL13, at rights of the boards panel, the other side the
cable connect to serial port in your laptop, select the at 1200bd
the velocity connections and flow to ALK-7 menu, its yours adjust
to pm. you need the IMEX manuals P/N C085U52M.04. IF YOU NEED
THIS MANUAL CONTACT TO ME AT [email protected].
[ Reply to This ]

Re: seno 600T hf


by Ricardo Faria on November 08, 2003
In response to: Tayfun Canli
Hi, to connect your laptop on Senix 600T, you must be use tha
cable (serial) to connect both, laptop and Mamo. the connect is
located inside of mammo, on the main board, right side. there is
2 or three connector in this mainboards-right side, the cable
have only one place to perfect connection.
Connect it and re-start mamo. Open the software and enjoy! more
questions? call me: 0055.31.9184.6755 Ricardo Faria
[ Reply to This ]

Re: seno 600T hf


by Milner A. Flecha on February 20, 2004
In response to: Tayfun Canli
Dear Mr. Tayfun:

can you provide me of the software for the Senographe 600T


system???

Regards

Milner
[ Reply to This ]

Re: seno 600T hf


by Manuel Casanova on February 21, 2004
In response to: Milner A. Flecha
Milner:

Please contac with me, I have a full information for 600T.

Manuel Casanova

[email protected]
[ Reply to This ]

You might also like