Dear Client,

Thank you for purchasing our ET-701 Single Phase Relay Tester.

Please read the manual in detail prior to first use, which will help you

use the equipment skillfully.

Our aim is to improve and perfect the company's

products continually, so there may be slight differences

between your purchase equipment and its instruction

manual. You can find the changes in the appendix.

Sorry for the inconvenience. If you have further

questions, welcome to contact with our service department.

The input/output terminals and the test column may

bring voltage, when you plug/draw the test wire or

power outlet, they will cause electric spark. PLEASE

CAUTION RISK OF ELECTRICAL SHOCK!

 SERIOUS COMMITMENT

All products of our company carry one year limited warranty from

the date of shipment. If any such product proves defective during this

warranty period we will maintain it for free. Meanwhile we implement

lifetime service. Except otherwise agreed by contract.

1
 SAFETY REQUIREMENTS

Please read the following safety precautions carefully to avoid

body injury and prevent the product or other relevant subassembly to

damage. In order to avoid possible danger, this product can only be

used within the prescribed scope.

Only qualified technician can carry out maintenance or repair

work.

--To avoid fire and personal injury:

Use Proper Power Cord

Only use the power wire supplied by the product or meet the

specification of this produce.

Connect and Disconnect Correctly

When the test wire is connected to the live terminal, please do not

connect or disconnect the test wire.

Grounding

The product is grounded through the power wire; besides, the

ground pole of the shell must be grounded. To prevent electric shock,

the grounding conductor must be connected to the ground.

Make sure the product has been grounded correctly before

connecting with the input/output port.

Pay Attention to the Ratings of All Terminals

To prevent the fire hazard or electric shock, please be care of all

ratings and labels/marks of this product. Before connecting, please

2
read the instruction manual to acquire information about the ratings.

Do Not Operate without Covers

Do not operate this product when covers or panels removed.

Use Proper Fuse

Only use the fuse with type and rating specified for the product.

Avoid Touching Bare Circuit and Charged Metal

Do not touch the bare connection points and parts of energized

equipment.

Do Not Operate with Suspicious Failures

If you encounter operating failure, do not continue. Please contact

with our maintenance staff.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in Explosive Atmospheres.

Ensure Product Surfaces Clean and Dry.

－Security Terms

Warning: indicates that death or severe personal injury may result if

proper precautions are not taken

Caution: indicates that property damage may result if proper

precautions are not taken.

3
 Contents
I. Summary ............................................................................................................ 5

II. Technical Parameter and Functions ........................................................... 5

III. Panel Layout and Function Description ................................................... 6

IV. The output power operation...................................................................... 7

V. Instruction ........................................................................................................ 8

VI. Notes ..............................................................................................................12

VII. Packing List ..................................................................................................12

4
I. Summary
ET-701 Single-phase relay tester is newly developed calibration device. The application of the

latest AC and DC voltage technology and current power source technology to the equipment

makes its circuit design, component selection, panel layout, and the internal structure design to

meet the advanced level in china. With many excellences for example perfect functions,

excellent Components, clear measuring data, simple operation and so on, the equipment is the

first choice for the power relay protection department.

II. Technical Parameter and Functions

(1) Running Conditions

Power Supply：AC220V±10% 50Hz

Work Environment：Temperature： -10℃～40℃

Humidity：≤85 %RH

(2) Output supply

AC voltage：0～220V/3A

AC current：0～100A/7.5V

0～20A/25V

0～5A/5V

DC voltage：0～220V/3A

DC current：0～20A/25V

Constant voltage output：DC24V DC48V DC110V DC220V

(3) Performance Specifications

1
Ammeter, voltmeter：4 /2 potential

Digital millisecond meter：0 ~ 99.9999s

(4) Performance Description

Measuring Relay. A Measuring Relay is provided to measure current and the start value,

return value and return coefficient/ drop-off to pick-up ratio of potential relay.

Time Relay. A Time Relay is provided to measure the start value, return value and operating

time.

5
 Auxiliary Relay. An Auxiliary Relay is provided to measure the start value, return value,

holding value and operating time of all kinds of auxiliary relays with starting coil and holding

coil.

Reclosing Relay. Reclosing Relays provide tests to Capacitance in charge time, reclosing time

and intermediated elements.

Differential Relay. Differential Relays provide DC excitation test, braking characteristics test

and volt-ampere characteristic test.

Other Uncommon Relays.

III. Panel Layout and Function Description

(1) Panel Layout

Figure (1)
(2) Function Description.

Name Function Description Remarks

The AC and DC power supply and fixed value Note: When measuring
J1, J2, J3, J4, J5
output terminals, see the front panel. action time of the relay,

Display ammeter/ voltmeter data(such as the start value, the relay contact should
X1
return value and fixed value) be linked with neither

6
 X2 Digital millisecond meter external power supply

S1 Power outlet nor J1, J2, J3, J4, J5 in

short-circuit condition.
S2 Electrical power switch

T1 Power output selector knob

T2 fixed current output selector knob

Contact selector knob( ( : according to light, you can know the

action value and the return value; Ⅰ: normally open contact on
T3 delay closing; Ⅱ : normally open contact power-down time
delay/off delay opening; Ⅲ: normally closed contact on delay
opening; Ⅳ: normally closed contacts off delay closing)
T4 Power output adjustment knob

Contact There insert the contact terminals of the measured relay

Z the power output type //

Action Contact action instruction. (connect to normally open //

contacts, the LED will turn ON; connect to normally closed
indication contacts, the LED will turn OFF )
The on-off switch of voltage or current output; in rated value //
Sync
do the impact test to the relay.
Fixed voltage Fixed voltage output switch //

Reset Milliseconds return to zero //

Closing The switch of the reclosing relay sending closing signal //

IV. The output power operation

(1) AC voltage output（0～220V）

Turn T1 to AC250V, and close the sync switch; adjust T4, J2 to 0 ~ 250V AC voltage output, X1

will display the current voltage, ACV LED will light.

(2) AC voltage output（0～5Ａ、0～20Ａ、0～100Ａ）

Turn T1 to AC5V/AC20V/AC100V, and close the sync switch; adjust T4, J1 to 0 ~ 5V/ 0～20Ａ

/0～100Ａ AC current output, X1 will display the current value, ACA LED will light.

(3) DC voltage output（0～220V）

Turn T1 to DC250V, and close the sync switch; adjust T4, J3 to 0 ~ 220V DC voltage output, X1

will display the current voltage, DCV LED will light.

7
(4) DC current output（0～20V）

Turn T1 to DC20V, and close the sync switch; adjust T4, J4 to 0 ~ 20V DC voltage output, X1 will

display the current value, DCA LED will light.

Note: adjusting the current, please do not exceed the rated current, otherwise the equipment

will be damaged.

(5) Fixed voltage output

Turn T2 to 24V, and close the fixed voltage switch; J5 will output 24V DC voltage.

Turn T2 to 48V, and close the fixed voltage switch; J5 will output 48V DC voltage.

Turn T2 to 110V, and close the fixed voltage switch; J5 will output 110V DC voltage.

Turn T2 to 220V, and close the fixed voltage switch; J5will output 220V DC voltage.

V. Instruction

(About instruction you can refer to "protection relay calibration", compiled by Water Resources

and Electric Power department Electric Power Production Division, published by China Water

Power Press.)
(1) Measurement
Can be used as voltage and current source respectively, in order to avoid the equipment

damage please pay more attention to all output power. Specific operations refer to section 4.
(2) Over range and Under range
Measuring the start value, the return value, return coefficient and contact action time of relays

(including voltage relay and current relay). Over range relay is defined by the action value of

the contact close. Under range relay is defined by the action value of the contact open.

Measuring the action value, the return value, and return coefficient of relays

Reference sections 4, turn T3 to , press the sync switch, and slowly adjust T4 to the relay

action, then the LED becomes ON, X1 displays this action value. Continue to adjust T4 to the

rated value, and then slowly back to the return value, at this time the LED turns OFF, X1 displays

this return value. Return coefficient = (the return value/the action value) %

Relay time measurement

Reference sections 4, turn T3 to the relay contact, press the sync switch, and slowly adjust T4 to

the rated value, through the sync switch, relay time can be measured. Note: before test, the

milliseconds should be cleared to zero and closing switch should be in OPEN condition.

8
Relationship between sync switch and contact is as follows:

In Ⅰ Ⅲ condition, sync switch from turn off to turn on;

In Ⅱ Ⅳ condition, sync switch from turn on to turn off.

Contacts are wired as follows:

(3) The measurement of time relays the same as above.

(4) Reclosing (take DH-3 reclosing for example)

1) DH-3 reclosing relay operation as follows: Wired as Fig.3,③ ④connected to black

J5(Negative electrode), ⒄connected red J5(positive electrode).

Note: when using contact ZJ3 to halt the milliseconds, disconnect

the cable form contact ZJ3 to ⑿( see "protection relay calibration" page 352), adjust T1 to

DC20A, turn the power supply ON, and turn T4 to relay rated current value. Turn OFF the

power supply, and turn T2 to relay rated voltage value. Adjust T3 to I( Relay ZJ3 is in contact

condition). Turn the power supply ON, press the fixed output switch, change for 15 to 25

seconds (the charge time will show in millisecond meter), reset the millisecond meter, press the

"reclosing switch", measuring reclosing time, then the value displayed in X2 is reclosing time

of reclosing relay.

9
 (5) Auxiliary Relay

See Fig.(a), the operation method same as the operating of over range/ under range relay

measuring action values, return values, action time, and return time.

See Fig.(b), for current holding relay, adjust T2 to the relay rated voltage, turn on power switch,

press the fixed value switch, and add the rated voltage to the relay voltage coil, after relay

action, adjust T4 to enable J1 to reach the rated current. Then disconnect the voltage, adjust

the protection coil current (T4), the minimum current that relay holds is the minimum hold of

relay. For testing action time and return time refer to section 5, term 2.

(6) Differential Relay (take BCH—1 differential relay for example)

As required in the regulations (see "protection relay test" page 178),

in the case of no external devices, just can do trials at NO. ④⑨⑩,

in external connecting regulator and current booster condition, just can do trials at NO. ⑥,

other trials do not belong to the scope of the instrument.

1) Check the action voltage, action current and return current of actuator elements, wiring as
flows:

Disconnect the serial gram between terminal ⑩ and ⑾, measure the action current and

return current as the current relay operating method, then rise the AC current to just measured

action current value, record this voltage value, and the voltage between terminal

J1 can get by the millimeter.

10
2) Initial ampere-turn check in no braking condition

This project is not included in routine examination. Put all the 20 working winding turns into

service, connect ⑩ ⑾ short-circuit chips, add AC current from terminal ③ ⑧, and join the

contact action signal to the contact terminal from ⑤ ⑦, verify as the current relay testing

method.

3) Brake Performance Test

Periodic inspection, only test the action ampere-turn value when Φ = 0 ° and the braking is 280

ampere-turn.

Wiring as above. Disconnect the serial grams of ④ ⑥, adjust the action loop to 39 turns and

the brake circuit to 14 turns, make sure 220V power supply apply to the voltage regulator

(minimum capacity 5KVA) and the equipment, and adjust the brake current to the required

ampere-turns, refer to the AC relay to operate the action current. If action ampere-turns are

completely wrong, it is possible the phase angle between the braking current and action

current is 180 °, reversing the braking current phase, all will be ok. If the equipment using one

phase of the three phase current, voltage regulator using another phase current, changing

their phase position in three phase current and the positive and negative of will get 60 ° phase

angle. If using external phase shifters, 0 ~ 360 ° phase angle is available.

4) The entire group Volt-ampere Performance test, wiring as flows:

AC current add to the working winding ③ ⑧, actuator elements voltage can be read out by

an multi meter from ⑨ ⑩. Adjusting J1 to AC current and boost current to 1 times, 2 times, 5
11
times ampere-turn, actuator elements voltage can be read out. See "protection relay test"

page183 for details.

5) Verify action ampere-turns in setting position

The test method same as current relay operation, see section 5, term 2.

VI. Notes

(1) For security, do not turn on the power switch when the equipment and the relay are

wiring. Make sure the wire is properly connected; you can turn on the power switch.

(2) For better accuracy, please warm-up the equipment for 5 to 10 minutes before test.

(3) When measuring contact action time, the millisecond should be cleared to zero after

adding the rated value.

(4) For any reason the Equipment fails to operate properly, please check each fuse holder. If

damaged, it is recommended to replace the same model units. It still cannot operate

properly, please contact with our company timely instead repair it by yourself.

(5) The output power supply cannot short-circuit with each other. The connection between

contact terminals and the output power cannot be in short-circuiting condition. All that

will damage the equipment.

(6) Please read the instruction manual carefully before using the equipment.

VII. Packing List

No. Name QTY

1 The host 1

2 Power cord 1

3 Test line 1

4 Fuse 4

5 Inspection report 1

6 Certificate 1

7 Warranty card 1

8 User manual 1

9 Packing list 1

12