rcW bryr @*)qfisr ffito{(

Gql - I
2423 P18
H$
BOOKLET NO.

Civil Engineering 205626

Paper II
Tirne Allowed : Three Hours Maximum Marks:200
Medium: English Type of Paper : Conventional

Question Paper Specific Instructions

Pleose read. eoch of the following instructions corefully before attempting
questione:
1. There are EIGHT questions divided in two Sections, out of which FM are to be
attempted.
2. Questions no. 1 and 5 are compulsory. Out of the remaining questions, THREE are to
be attempted choosing at least ONE question from each Sections.
t-l
3. Ttre number of marks carried by a question/sub question is indicated against it.
4. Keep in mind the word limit indicated in the question if any. IEI
U)
5. Wherever option has been given, only the required number of responses in the serial
order attempted shall be assessed. Unless struck ofl attempt of a question shall be
counted even if attempted partly. Excees responses shall not be assessed and shall be
ignored.
6. Candidates are expected to answer all the sub-questions of a question together.
ff sub-question of a question is attempted elsewhere (after leaving a few page or after
attempting another question) the later sub-question shall be overlooked.
7. Any page or portion of the page left blank in the Answer Booklet must be clearly struck
off.
8. Unless otherwise mentioned, symbol and notation have their usual standard meanings.
Assume suitable data, if necessary and indicate the same clearly.
9. Neat sketches may be drawn, wherever required.
10. The medium of answer should be mentioned on the answer book as claimed in the
application and printed on admiseion card. The answers written in medium other than
the authorized medium will not be assessed and no marks will be assigned to them.

Note - 1. Candidates will be allowed to use Scientific (Non-programmable type) calculators.

P.T.O.
 ;
.t
.
., . '| !. l, t jO
t 'i

,it
'1..
t
r' t

2 P18
H$ SECTION-A

Ql. W'rite short notes on any five of the following. (8x5=40)

(a) Four instruments used for Surveylng.
(b) Geosynthetics.
(c) Principles of Building Planning.
(d) Fluid Statics and Buoyancy.
(e) Hydraulic Turbines.
(f) Methods of Irrigation.
(g) Hydrographic surveyrng.
Q2. (a) Discuss three methods for plane table surveylng. (5x8=15)
(b) Discuss the qualities of ,
,) Good Building Stone.
iil Good Bricks.
iii) Good Cement. (5x3=15)
(c) Explain in short,
1) Temporary adjustments of dumpy level.
/ ii) Rise and fall method.
iiil Height of instrument method.
rv) Change point. (2.5x4=10)

Q3. (a) Explain in detail, for building constructior,

r) Ventilation.
ii) Acoustics.
iil) Fire Protection. (5x8=15)
(b) Explain in detail, for f1uid,
i) Viscosity.
iil Compressibility.
iiil Surface tension and capillarity. (5x3=15)
(c) Explain in short,
il cwR.
ii) Water logging.
iil) River Training.
lv) Spillways. (2.5x4=10)

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 3 P18
H$
Q4. (a) Explain in detail,
il Types of Centrifugal Pump.
ii) Components and working of reciprocating pump.
iir) Layout of powerhouse with pondage and storage. (5x3=15)
(b) Explain in detail,
i) Energy Dissipation.
- iil Diversion Head works.
iii) Cross Drainage works. (5x3-15)
(c) Explain in short,
i) Types of Foundatiorrs.
ii) Water proofing of flat roofs. (5x2=10)

|}

P.T.O.

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 4 Pl8
Hfi
SECTION- B
Q5. Write short notes on any five of the following. (8x5=40)
(a) Human characteristics as road users.
(b) TBM.
(c) Four methods of valuation.
(d) Floods and Flood routing.
(e) Sotrrces for water supply.
(0 Sources and effects of air and noise pollution.
(g) Disposal of solid wastes.
Q6. (a) Explain in detail, five road patterns. (3x5=15)
(b) Explain in detail,
r) Mucking and Ventilation in tunnels.
iil NATM.
iii) Cut and cover method for metro tunnelling. (5x3-15)
(c) Explain in short,
1) Factors affecting rate analysis.
ta

: iil Overhead cost and outturrl. (5x2=10)

G# hI Explain in detail, six types of estimates. (2.5x6=15)
-'r
fffit-!

f*-
lg€*
ffi
Q7. (a)

tEl
a=

(b) Explain in detail,

ffi U) il Water quality standards.
iil Primary and secondary water treatment.
iiil Conveyance and distribution of treated water. (5x3=15)
(c) Explain in short,
il Resenroir planning.
ii) Sediment control. (5x2=10)

Q8. (a) Explain in detail,

i) Sourees and classification of solid waste.
ii) Solid waste collection systems.
iii) Transfer stations and layout of solid waste collection route. (5x3=15)
(b) Explain in detail,
i) Hydrological cycle.
ii) Infiltrometers.
iii) Factors affecting run-off. (5x3-15)
(c) Explain in short,
"White-topping" and its three methods. (1+gx3=10)

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 .ta C3rrrl) rZfiFT-.1o13 ,fr.zc ffi1o2(.
(UEr{ - r,)
2023 o18
ffi BOOKLET NO.

Civil Engineering 1056?-6

PaPer -I
Maximum Marks : 200
Time Allowed: Three Hours
Type of Paper : Conventional
Medium: English
Question Paper Specific Instructions
attempting
please rcad, eaeh of the following instructions carcfully beforc
questions :
questions divided in two sections' out of which
FwE are to be attempted'
l. There are EIGHT

2.Questionsno.landSarecompulsory.outoftheremainingquestions,THREEaretobe
from each Sections' l

attempted choosing at least ONE question x

F] I

l
I

S.Thenumberofmarkscarriedbyaquestiorr/subquestionisindicatedagainstit. I

rc
a
I

question if any'
4. Keep in mind the word limit indicated in the
I

+
order
required number of responses in the serial
5. wherever option has been given, only the even if
shall be assessed. unless struck off, attempt of a question shall be counted
attempted
attemptedpartly.Excessresponsesshallnotbeassessedandshallbeignored.
If sub-question of
to answer all the sub-questions of a question together'
6. candidates are expected
another question)
(after leaving a few pag" or after attempting
a question is attempted elsewhere
the later sub'question shall be overlooked'

T.AnypageorportionofthepageleftblankintheAnswerBookletmustbeclearlystruckoff.

8.Unlessothenrlisementioned,symbolandnotationhavetheirusualstandardmeanings.Assume
the same clearly'
suitable data, if necessary and indicate

9. Neat sketches may be drawn' wherever required'

on the answer book as craimed

in the application and
of answer should be mentioned
10. The medium
printedonadmissioncard.Ttreanswerswritteninmediumotherthantheauthorizedmedium
be assigned to them'
will not be assessed and no marks will

Note-l.CandidateswillbeallowedtouseScientifrc(Non-programmabletype)calculators.
P.T.O.
 I

ffi 2

SECTION-A
o18

Qr. Answer any five of the following:

(8x5=40)
(a) A compound tube consist of steel tube
150 mm internal diameter and 10
mm
thickness and outer brass tube 170 mm
internal diameter and 10 mm thickness,
the two tube are of same length. The
compound tube carries axial load 1000
N.
Find the stresses and load carried by
each tube and also amount of shorten
L = 150 mm, E, = Z x105 Mpa, Et 1 x 10EMpa.
=
O) Analyse a continuous beam as shown
in Fig.
30 kN/m
240 kN
B
A
L2m C
4m 8m
(c) Find a rear root of the equation x e-x
using Newton Raphson method.
=
(d) A 3 hinged parabolic arch of 2o m span
and B m rise is carrying a point load
of 100 kN at 7'5 m from left support.
Find the value of horizontal thrust
and
BM at 7.8 mfrom right support.
(e) Explain the term plastic hinge and prastic
corapse.
(0 Explain factors to be considered for
selection of equipment in construction
industry.
(g) Derive the relation for beam deflection
of simpry supported beam carries
uniformly distributed load w kN/m
over entire span.

Q2. (a) Draw shear force and bending moments

for the beam as shown below.
r5
80 kN/m 15 kN
A C
3m B 3m 2mD

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 3 o18
HH
(b) Analyse the truss supported and loaded. as shown in fig. if support B sink by
3 mm, E = 210 GPa and A = 400 mm2.
15
75 kN
F E D
20 kN

3m

A C
3m 3m

(c) Find the positive root of equation xex = 1 which lies between 0 and 1. 10

15
QS. (a) Analyse the continuous beam by flexibility method.
30 kN
10 kN/m 30 kNlm
B
A
2mDZm 1.5m E 2m

(b) Design a plate girder for the span 24 mcarries a load 100 kN/m simply
15
supported at two ends. (connection - welded)

(c) Explain ABC analysis concept and ABC classification of construction

material. 10

Q4. (a) Describe in details :

15

r) Resource planning Process.

ii) Importance of planning.

iil) Function and role of chief planner in construction project management.

P.T.O.

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 4 o18
HH
(b) Analyse the frame by moment distribution method. 15

6 kN/m
B C
4m

4m

(c) Tko wheel loads 80 kN and 120 kN spaced at 3 m apart move along the beam

of span L2 m simply supported. Find the maximum BM at 4 mfrom left

support using influence line diagram concept. 10

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 b- o18
HH
SECTION _ B

Q 5. Answer any five of the following : (gx$=40)

(a) A rectangular beam 230 mm wide and 415 mm effective depth is reinforced.
with 3 bars of 20 mm diameter in tensile zone and 2 bars of 16 mm diameter
in compression zotte. Determine moment of resistance using WSM. Use
M20 and Fe41b.
(b) Explain in detail distribution of loading on staircase and effective span on
stairs.
(c) Explain the factors to be considered for site selection in bridges.
(d) Explain how aggregates can be classified based on weight, size, shape and
texture.
(e) write a short note on pretension system in prestressing.
(f) The dry unit weight of soil having l2o/o water content is 1g12 kN/m3. t

Find bulk unit weight, saturated unit weight and submerged unit weight
(take G = 2.6b).
(g) Write short notes on :
i) Permeability of concrete.
ii) Durability of concrete.

Q6. (a) Design a RC slab for a room of size 4 m x 6 m. The slab is simply supported
on all the four edges and carries a live load 2 kN/mz FF 1 kN/mz MZO
= and
Fe415. tE
(b) Design a watertank for following data
openrectangulartank 4 m x 6 m x B m deep rest on ground. rE
Use M20 concrete
Fe415 steel
Use (WSM) for analysis.
(c) Design a column to carry an axial load of 800 kN. Design the column as per
IS code. Consider rectangular short column. l0

P.T.O.

FB/IG/TG @mpscmaterial www.mpscmaterial.com

 6 o18
H#
15
Q7. (a) Write short notes on :
i) WaterwaY calculation
ii) Scour dePth
I

iii) Economical gp.gn for bridge construction'

properties
(b) Explain the term grading of aggregate and also explain its effect on
15
of concrete.
10
(c) Describe Terzaghi-s bearing capacity theory of shallow foundation'

Qg. (a) A prestress concrete beam of rectangular section 300 mm x 600 mm has
a span of L2 m. The effective prestressing force 980 kN at eccentricity of
120 mm. The DL = 4.5 kN/m and LL = 7.5 kN/m. Determine extreme
15
stresses at
F] a) end section

F4 b) mid span without LL

L--
a c) mid span with LL.

(b) The void ratio of clayA decreased fro m}.572to 0.505 under a change in pressure

from L2O to 180 kg/m2. The void ratio of clay B decreased from 0.6L2 to 0.597'
was 3
The thickness of sample A was 1.5 times that of B, tf.l}yo consolidation

times longer for sample B than sample A. what is the ratio of the coefficient

of permeabilitY of A to that of B ? 15

(c) Explain advantages and disadvantages of prestressing. 10

tts lr r tla rlta ---.I!llt E!' TrftrrrllLrffil

I 'ri

FB/IG/TG @mpscmaterial www.mpscmaterial.com