Advantages

LATAPOXY® 300 • Prevent curling of moisture sensitive marbles & agglomerated

tiles.
Epoxy Adhesive •Will not stain white or light coloured marbles.
•High Chemical resistance for industrial and commercial
installations.
• Safe, non-flammable.
• Water cleanable while fresh.

Suitable Substrates
• Concrete • Cement Mortar Beds
• Ceramic Tile and Stones • Cement Backer Board
• Exterior Grade Plywood* • Gypsum Wallboard*
• Concrete Masonry • Cement Plaster
• Brick Masonry • Cement Terrazzo
• Vinyl or Other Resilient Tile* • Steel

*Interior application only

**Consult cement backer board manufacturer for specific
installation recommendations and to verify acceptability for
exterior use.
PRODUCT DESCRIPTION
LATAPOXY® 300 Epoxy Adhesive is a chemical resistant
Packaging
epoxy adhesive that will bond to most sound, clean Factory proportioned unit consisting of three conveniently
surfaces. Adhesive spreads easily and cleans with water packed components hardener, resin (Part A & Part B) and filler
while fresh. LATAPOXY® 300 Epoxy Adhesive is a factory- powder (Part C)
proportioned kit consisting of epoxy resin, hardener and
chemical resistant silica filler. LATAPOXY® 300 Epoxy #1 Unit (5 kgs)
Adhesive can be used in interior and exterior (see
limitations) walls and floors, wet and dry areas.
Coverage

Approx 12-15 sft per 5 kg unit with 1/4” x 1/4”

Application
(6mm x 6mm) sq. notch trowel
For heavy duty commercial chemical resistant installations
in food processing areas, commercial kitchens, restaurants,
Shelf Life
etc. Also use LATAPOXY® 300 Epoxy Adhesive to install all Factory sealed containers of this product are guaranteed to be
types of ceramic tile, marble and natural stone over post- of first quality for two (2) years.
tensioned and precast floor systems. Also recommended
for rubber flooring and wood block floors. For the Limitations
installation of green marble, white marble and agglomerate •Not for use as a grout. Use LATAPOXY SP-100 Stainfree Epoxy
marbles that have a tendency to stain, darken, or warp Grout or LATAPOXY® 2000 Industrial Epoxy Grout.
• Do not install when surface temperature is below 60°F (16°C)
when installed with water based installation materials.
or above 90°F (32°C). For temperatures between 40°-60°F (4-
NOTE: The Tile Council of America recommends the use of
16°C), use LATAPOXY® 300 Rapid Epoxy Adhesive.
epoxy adhesives and grouts for thin-set installations on
suspended concrete slabs and for floors and walls when
chemical resistance is required.
•Adhesives for ceramic tile and stone are not replacements
for waterproof membranes. When a waterproof Specifications subject to change without notification.
membrane is required, use LATICRETE® Waterproof Results shown are typical but reflect test procedures used.
Membrane Actual field performance will depend on installation
•Consult LATICRETE® Technical Services on limitations for methods and site conditions.
exterior installations.
•When installing ceramic tiles, verify that substrate Chemical Resistance Chart (at 70 °F/21 °C)
deflection does not exceed the industry standard of L/360
of the span under combined live and dead loads. Not to be LATAPOXY® 300 EPOXY ADHESIVE
used with engineered wood joist systems. Some marbles REAGENT TYPE EXPOSURE LEVEL
and other natural stone have low flexural strength and may (at 70°F/21°C) Intermittent* Constant**
not be suitable for installation over wood floors. Citric Acid 10% R R
Sulfuric Acid 10% R R
Cautions Hydrochloric Acid 10% R R
•During cold weather, protect finished work from traffic Lactic Acid 5% R R
until fully cured. Vinegar R R
•Until cured LATAPOXY® 300 Epoxy Adhesive may irritate
Acetic Acid 10% R NR
eyes and skin. Avoid contact with eyes or prolonged
Nitric Acid 10% R R
contact with skin. In case of contact, flush thoroughly with
Sodium Hydroxide 10% R R
water.
Sodium Chloride 10% R R
•Contains Silica sand. Silica sand may cause cancer or
Concentrated Detergents R NR
serious lung problems. Avoid breathing dust. Wear a
respirator in dusty areas. Ammonium Hydroxide R R
•Keep out of reach of children. Sugars R R
Gasoline R NR
TECHNICAL DATA Cooking Oils R R
Turpentine R R
Mineral Spirits R R
Applicable Standards
Toluene NR NR
ANSI A118.3-1999
Xylol NR NR
Performance Properties
R= Recommended • NR= Not Recommended
Test Test Method Results
Chemical Resistance determined in accordance with ASTM
C267-1982.
Shear Bond Quarry ANSI A118.3- >1250psi
NOTES TO SPECIFIER: Use the constant exposure
tile, 28 day cure 1999; E-5.5 (8.6 MPa)
recommendations for intermittent exposure to reagents at
temperatures above 90°F (32°C).
ANSI A118.3- 1700 psi
Tensile Strength
1999; E-5.7 (11.7 MPa)
* Intermittent is less than 3 days exposure.
ANSI A118.3- 7500 psi ** Constant is 1 month exposure
Compressive Strength
1999; E-5.6 (51.7 MPa)
Thermal Shock ANSI A118.3- >1200 psi
INSTALLATION
Resistance 1999; E-5.8 (8.3 MPa)
ANSI A118.3- Surface Preparation
Shrinkage 0.03% All surfaces should be between 60°F(16°C) and 90°F(32°C)and
1999; E-5.3
structurally sound, clean and free of all dirt, oil, grease, Loose
ANSI A118.3-
Sag Resistance Pass peeling paint, concrete sealers or curing
1999; E-5.4
compounds. Rough or uneven concrete surfaces should be
made smooth with LATICRETE® Latex Portland Cement
Working Properties at 70°F (21°C))
underlayment to provide a wood float (or better) finish.
Pot Life 45 minutes Installation may be made on a damp surface. New concrete
Time to Traffic 24 hours slabs must be damp cured and 28 days old prior to application.
All slabs must be plumb and true to within ¼”(6mm) in 10 ft LATAPOXY® 300 Part C Filler Powder and mix to a smooth,
(3m). Expansion joints shall be provided through the tile trowelable consistency. Mortar is ready for use immediately
work from all construction or expansion joints in the after mixing.
substrate. Follow ANSI Specification AN-3.8 “Requirements
Application
for Expansion Joints” or TCA Detail EJ171-Current Year
Apply adhesive to the substrate with the flat side of the trowel,
“Expansion Joints”. Do not cover expansion joints with pressing firmly to work into surface. Comb on additional
mortar. Glass Mesh Mortar Unit: follow TCA installation adhesive with the notched side. Use the proper sized notched
detail W244. Note: Temperature will effect working trowel to insure full bedding of the tile. Spread as much
properties of LATAPOXY® 300. Warm temperatures will adhesive as can be covered with tile in 10 minutes. Back butter
speed curing and shorten working time. Cool temperatures large tiles (> 12”x12”) to provide full bedding and firm support.
will slow curing and require longer time to traffic. Place tiles into wet, sticky adhesive and beat in using a beating
block and rubber mallet to imbed tile and adjust level. Check
Store LATAPOXY® 300 Epoxy Adhesive at 70°F(21°C) for 24
adhesive for complete coverage by periodically removing a tile
hours prior to use. and inspecting bedding adhesive transfer onto back of tile. If
1. Installer must verify that deflection under all live, dead adhesive is skinned over (not sticky), remove and replace with
and impact loads of interior plywood floors does not fresh adhesive.
exceed industry standards of L/360 for ceramic tile and
brick or L/480 for stone installations where L=span length; Grouting
2. Minimum construction for interior plywood floors. Grout installation after a minimum of 24 hours curing time at
70°F(21° C). Grout with LATICRETE® Sanded or Unsanded Grout
SUBFLOOR: 5/8” (15mm) thick exterior grade plywood,
mixed with LATICRETE 1776 Grout Admix plus .For maximum
either plain with all sheet edges blocked or tongue and stain resistance use LATAPOXY® SP-100 Stainfree Grout or
groove, over bridged joints spaced 16” (400 mm) o.c. SpectraLOCK® Pro Premium Grout.
maximum; fasten plywood 6” (150mm) o.c. along sheet
ends and 8” (200mm) o.c. along intermediate supports with Cleaning
8d ring-shank, coated or hot dip galvanized nails (or Clean tools and tile work with water while adhesive is fresh.
screws); allow 1/8” (3mm) between sheet ends and ¼”
(6mm) between sheets edges; all sheet ends must be AVAILABILITY AND COST
supported by a framing member; glue sheets to joints with
Availability
construction adhesive;
LATICRETE and LATAPOXY ® materials are available worldwide.
UNDERLAYMENT: 5/8” (15mm) thick exterior grade For distributor information:
plywood fastened 6” (150mm) o.c. along sheet ends and 8” Telephone: +91-40-23378775/76/79
(200mm) o.c. in the panel field (both directions) with 8d FAX: +91-40-23378784
ring-shank, coated or hot dip galvanized nails (or screws); e-mail: [email protected]
allow 1/8” (3mm) to ¼” (6mm) between sheets and ¼”
(6mm) between sheet edges and any abutting surfaces; Cost
Contact a LATICRETE® Distributor in your area.
offset underlayment joints from joints in subfloor and
stagger joints between sheet ends; glue underlayment to
MAINTENANCE
subfloor with construction adhesive. Refer to Technical
LATICRETE® and LATAPOXY® grouts require routine cleaning
Data Sheet 152 “Requirements for Direct Bonding of
with neutral pH soap and water or MYK LATICRETE Clenza series
Ceramic or Stone Tiles Over Wood Floors” for complete
suitable cleaners. All other LATICRETE® and LATAPOXY®
details.
materials require no maintenance but proper installation as per
3. DO NOT bond to particle board, luan, Masonite® or
hardwood surfaces. instruction.
Performance and durability may depend on properly
Mixing maintaining of Installed area.
Pour LATAPOXY® 300 Epoxy Adhesive Part A and Part B
into a clean mixing pail and mix thoroughly. Add
WARRANTY
MYK Laticrete India Pvt Ltd warrants LATICRETE ® 300
Epoxy Adhesive is free from manufacturing defects and will
not break down, deteriorate or disintegrate under normal
usage for a period of two (2) year from manufacturing of
the product subject to the terms and conditions stated in
LATICRETE® Product Warranty.

TECHNICAL SERVICES
Technical assistance
Information is available by calling the MYK LATICRETE®
Technical Service at:
Telephone: +91-40-30413100
FAX: +91-40-23378784
e-mail: [email protected]

MYK Laticrete India Pvt Ltd.

8-2-703/A, Fourth Floor, Leela Gopal Towers
Banjara Hills, Road No-12
Hyderabad – 500034 (A.P)
Tel: +91-40--30413100
Fax: +91-40-23378784
e-mail: [email protected]
Website: www.myklaticrete.com