Technical Instruction Jenbacher- Oils
Technical Instruction Jenbacher- Oils
Technical Instruction
1 Scope ....................................................................................................................................... 1
2 Purpose ................................................................................................................................... 2
3 Additional information ........................................................................................................... 2
4 Effects on the lubricating oil and the oil service life .......................................................... 2
5 Lubricating oil requirements for Jenbacher gas engines .................................................. 3
6 Lubricating oil tables – selection overview: ........................................................................ 3
6.1 Note .......................................................................................................................................... 3
6.2 Lubricating oil table for Type 6 Jenbacher gas engines versions H and K............................... 3
6.3 Lubricating oil table for Type 6 Jenbacher gas engines versions F and J ............................... 4
6.4 Lubricating oil table for Type 6 Jenbacher gas engines versions C and E............................... 5
6.5 Lubricating oil table for Type 4 Jenbacher gas engines version C ........................................... 7
6.6 Lubricating oil table for Type 4 Jenbacher gas engines version B ........................................... 8
6.7 Lubricating oil table for Type 4 Jenbacher gas engines version A ......................................... 10
6.8 Lubricating oil table for Type 2 and 3 Jenbacher gas engines ............................................... 12
6.9 Lubricating oil for Jenbacher gas engines for special gas applications .................................. 15
6.10 The following products can also be used ................................................................................. 1
7 Revision code ......................................................................................................................... 1
NOTE
Observance of the conditions of this technical instruction and performance of
the activities described therein is the basis of safe and efficient plant
operation.
Non-observance of the conditions of this technical instruction and/or non-performance of the
prescribed activities or any departure from the prescribed activities may result in the loss of
guarantee rights.
The activities and conditions defined in this technical instruction shall be performed and/or
observed by the plant operator. This shall not apply if this technical instruction is expressly
allocated to the area of responsibility of INNIO Jenbacher GmbH & Co OG or a contractual
agreement between the operator and INNIO Jenbacher GmbH & Co OGprovides for a
different arrangement.
1 Scope
This technical instruction (TA) applies to the following Jenbacher Gas Engines:
• Type 2 engines
• Type 3 engines
• Type 4 engines
• Type 6 engines
2 Purpose
This technical instruction (TA) facilitates the selection of lubricating oils, tested for suitability in Jenbacher
Gas Engines.
3 Additional information
This Technical Instruction applies to new and overhauled engines, as of the date of issue. Lubricating oils
listed in this version are also released for engines built or overhauled before this version.
Lubricating oils no longer listed in this version remain released for engines that were listed before this
revision of the Technical Instruction was issued, as long as a Service Bulletin (SB) does not state
otherwise.
INNIO Jenbacher GmbH & Co OG closed a long-term development contract with ExxonMobil in 2019,
which allowed the introduction of Jenbacher N Oil 40.
More information on Jenbacher N Oil 40 and product data sheets are available at www.innio.com/
engineoil .
The limit values to be used for Jenbacher N Oil 40 are specified in TA 1000-0099B.
Relevant documents:
TA 1000-0099A – Approval procedure for various engine oils
TA 1000-0099B – Limit levels for used oil in Jenbacher gas engines
TA 1000-0099C – Procedure for testing the plant-specific oil service life
TA 1000-0112 – Taking lubricating oil samples / lubricating oil sampling protocol
TA 1000-0300 – Fuel gas and combustion air requirements
Lubricating oil can lose its corrosion-protection properties as a result of impurities in the fuel gas. The
results of periodic lubricating oil analyses provide indications of fuel gas contamination. See the following
technical instructions:
TA 1000-0112 – Taking lubricating oil samples / lubricating oil sampling protocol
TA 1000-0099A – Approval procedure for various engine oils
TA 1000-0099B – Limit levels for used oil in Jenbacher gas engines
TA 1000-0099C – Procedure for testing the plant-specific oil service life
6.1 Note
When using oils with an ash content of > 0.6%, increased performance of the engine components can be
achieved.
Oils with an ash content of > 0.6% in accordance with the specification are identified in a separate
column.
• A, B, C, S: Fuel gas classes, products for fuel gas class S, see chapter ⇨ Lubricating oil for
Jenbacher gas engines for special gas applications
• CAT: If an oxidation catalytic converter is included in the Jenbacher scope of supply
6.2 Lubricating oil table for Type 6 Jenbacher gas engines versions H and K
Jenbacher N Oil 40 X X X
6.3 Lubricating oil table for Type 6 Jenbacher gas engines versions F and J
Jenbacher N Oil 40 X X X
6.4 Lubricating oil table for Type 6 Jenbacher gas engines versions C and E
Company Brand Name Ash > 0,6% A B C CAT
Jenbacher N Oil 40 X X X
6.5 Lubricating oil table for Type 4 Jenbacher gas engines version C
Company Brand Name Ash > 0,6% A B C CAT
Jenbacher N Oil 40 X X X
6.6 Lubricating oil table for Type 4 Jenbacher gas engines version B
Company Brand Name Ash > 0,6% A B C CAT
Jenbacher N Oil 40 X X X
6.7 Lubricating oil table for Type 4 Jenbacher gas engines version A
Company Brand Name Ash > 0,6% A B C CAT
Jenbacher N Oil 40 X X X
Addinol MG 40 Extra LA X X X
Addinol Gas Engine Oil LG 40 X X
Addinol Gas Engine Oil NG 40 X
Addinol Eco Gas 4010 XD X X
Castrol Duratec L X X X
Castrol Duratec HPL X X
Castrol Duractec LD X
Cepsa Troncoil Biogas Low Ash X X
Cepsa Troncoil Gas LD 40 X
Cepsa Troncoil Gas JGC X X
ENEOS Gas Engine Oil M40(M) X
Fuchs Titan Ganymet LA X X
Fuchs Titan Ganymet Ultra X X X X
Fuchs Titan Ganymet Ultra LA X
Fuchs Titan Ganymet PRO MA X X
Fuchs Titan Ganymet PRO LA X
LUKOIL Efforce XDI 4004 X
Mobil Pegasus 1105 X X
Mobil Pegasus 1005 X
Mobil Pegasus 705 X X X
Mobil Pegasus 805 X X X
Mobil Pegasus 605 Ultra X X X
MOL GMO Long Life X X X
Morris Lubricants GEO Ultra 40 X
Morris Lubricants GEO Ultra G-LF 40 X X
Morris Lubricants GEO Ultra LZ 40 X X
Motul Gasma X
Motul Cressida X X
Petro Canada Sentron LD 5000 X X
Petro Canada Sentron LD 8000 X X X
Petro Canada Sentron CG 40 Plus X X X
Petronas GEO NG X
Petronas GEO BLG X X
Petronas GEO Syn 40 X
Puma LA Natural Gas S x
Q8 Oils Mahler G4 X X
6.8 Lubricating oil table for Type 2 and 3 Jenbacher gas engines
Jenbacher N Oil 40 X X X
6.9 Lubricating oil for Jenbacher gas engines for special gas applications
The following products can also be used without the "Best Effort" (BE) guarantee:
Company Brand Name Ash > 0,6% S CAT
Jenbacher N Oil 40 X X X
Responsible: Waldron P.
TA 1000-1109
Nils Burian Plus SAE 40 X X X X X
Release date: 26/11/2020
Responsible: Waldron P.
SRS Mihagrun 40 X X X
7 Revision code
Revision history
Index Date Description/Revision summary Expert
Auditor
22 26.11.2020 Neues Öl: Jenbacher N Oil 40 hinzugefügt / New oil: Pearson L.
Jenbacher N Oil 40 added Waldron P.
Korrektur der Schmieröltabellen / Correction of lubricating oil
tables
21 28.02.2020 Neue freigegebene Öle aufgenommen; Neugestaltung des Chvatal S.
Layouts; Eigene Ölliste für J624 erstellt / Added new released Waldron P.
oils; redesigned layout; created own oil list for J624
20 29.03.2019 Korrektur der Schmieröltabellen / Correction of lubricatiing oil Chvatal S.
tables Waldron P.
19 12.06.2018 Korrektur der Schmieröltabellen / Correction of lubricatiing oil Chvatal S.
tables Waldron P.
18 28.02.2018 Aktualisierung der Schmieröltabellen / Update of lubricating oil Chvatal S.
tables Waldron P.
17 30.11.2016 Ergänzungen in Kapitel 6.2, 6.5 und 6.8 / Additions in Chapter Chvatal S.
6.2, 6.5 and 6.8 Waldron P.