Micropack SRB

Power Supply System

30V / 960W and 24Ah batteries
Compact rack mounted power supply system

The Micropack SRB have been designed for

industrial and aviation applications with power
requirements in the range of 240-960W.
With its compact design, simple installation and
internal 24Ah backup batteries, it makes it really a
“micro” DC backup system.
FRONT VIEW

REAR VIEW

MICROPACK SRB SYSTEM 30VDC 960W

CU0403.003.DS3 – rev1

PRODUCT DESCRIPTION APPLICATIONS KEY FEATURES

The basic power core can house up to 4  3U COMPACT DESIGN
Aviation, Wireless, fiber and broadband
rectifier positions, a Smartpack controller and
Industrial – Power utilities, process  INTEGRATED DISTRIBUTION
small battery and load distribution unit industry, Air com, marine and offshore  DIGITAL CONTROLLERS
 INTERNAL 24AH BATTERY BANK
The power core is basically prepared for any Today’s communications demand state of
 DROP DIODES AND BYPASS RELAY
Micropack rectifier module and the system the art, cost efficient and compact DC power
 HEAT MANAGEMENT
output can be either of the following: systems. The Micropack delivers a cost-
(based on module choice) efficient power solution that can be easily  UNIQUE INSTALL ABILITY
 29V/240 – 960W / 10 – 40A adapted for applications where there is  GLOBAL APPROVALS
 12V, 48V and 60V on request limited space.

The system is monitored and controlled by the Industrial – Power utilities, process
Smartpack controller, but if larger display or industry, Air com, marine and offshore
extended controller functionality is needed it
Increasing demand for reliable DC power
can be operated by a PC with Powersuite
with or without battery backup makes
Inside the 3U unit there is space for backup
Micropack SRB the ideal choice in the small
batteries (two banks of 5pcs 6V/12Ah)
power range
Simple removable front cover gives good
access for service and maintenance.

Eltek — Gråterudveien 8, PB 2340 Strømsø, 3003 Drammen, Norway Phone: +47 32 20 32 00 Eltek © 2017 – www.eltek.com
 RECTIFIERS
Plug and play
The Micropack SRB comes with power core and controller. Set
the output voltage of the system by inserting the proper rectifier
type. The controller will automatically set default settings for the
selected output voltage range. The power core is coded to
prevent a rectifier with an incorrect output voltage being
inserted into the system.
Redundancy and features
The rectifiers communicates over the internal CAN bus for active
current sharing. Redundancy is achieved by installing more
rectifiers than needed for supplying the load. The controller has
an efficiency mode that shuts down spare rectifiers when load is
low to save power. Energy supplied by the rectifiers can viewed
in the controller Web pages. Details on rectifier status, firmware
and serial number are also available. The controller can be set up
to give alarms or warnings if the system is loaded with levels
exceeding its total capacity (based on installed functional
rectifiers).

Part number Description Voltage Efficiency # cells supported Output

range Pb NiCad protection
241120.300 Micropack 12V/120W WOR 10.7 – 18.0 V > 88% (50-100% load) 6 or 7 10 or 11 Fuse
241115.200 Micropack 24V/240W WOR 21.5 – 36.0 V > 92% (50-90% load) 12 or 15 20 to 22 Fuse
241115.100 Micropack 48V/250W 43.5 – 57.6 V > 93% (55-100% load) 24 - Fuse

MICROPACK PERFORMANCE
Constant power and short circuit proof
The Micropack rectifier has a constant power
characteristic in their supported output voltage
range. The output current is limited if the output
is short-circuited and voltage falls below the VDC Max output current vs output voltage
rectifier output voltage range.
60
Power boost 241120.300
The 24V Micropack rectifiers are allowed to
241120.300 boost
enter a boost mode for up to 60sek. 50
During boost they can deliver 30-40% more 241120.200
power than rated (maximum 15A). 241120.200 boost
40
This helps starting up capacitive loads.
241120.100
Selective fuse tripping (SBF)
In a multi-branch, battery-less system it is vital 30
that the rectifiers can provide enough current
for tripping the load fuses. If there is a short in
20
one branch, its fuse needs to be tripped quickly
in order for the other branches to operate
unaffected. This 24V rectifier will give a 50 to 10
55A pulse duration of 35ms to help tripping
fuses. This is initiated by a sudden drop in the
0
output voltage exceeding 5V.
0 2 4 6 8 10 12 14 16 IDC

Eltek — Gråterudveien 8, PB 2340 Strømsø, 3003 Drammen, Norway Phone: +47 32 20 32 00 Eltek © 2017 – www.eltek.com
MICROPACK SRB
…as a simple rectifier unit
If the application has the need for a pure DC power supply the SRB
offers a neat, easy installable enclosure for the Micropack rectifiers. It
has room for a few small components as load breakers and connection
terminals.
…as a small complete battery backup dc power system
With two banks of 30V/12Ah batteries, a battery shunt and contactor, and
a few load breakers installed. The Micropack SRB is a miniature full-
blown DC power system that will power the load during mains failures. If
more battery capacity is needed, A separate battery unit in same design
can be added on a shelf below the SRB, or in a separate cabinet.

Batteries
See the following discharge curve for the SB 12-6L
(Long lifetime 6-9 year) batteries

Control
The Smartpack controller offers comprehensive control and monitoring of
the whole SRB DC System, it being simple or complex.
It has three configurable inputs that can be used for monitoring
temperature, voltage or digital signals into the system. Minor and major
low and high alarm limits are configurable monitors separately on each
input.

Warnings and alarms are visible via the LED’s on the controller front.
There are also 3 configurable relays that can control external buzzers,
lamps, or remote signal to a control center for specified alarm events.
Finally, if the SRB is connected to an Ethernet connection, alarms can
send SNMP TRAP’s to and NMS system or e-mails.

To configure the system, such as setup change, inputs and alarm config,
communication parameters or change from the default settings for each
voltage range, a PC with Powersuite or a web browser needs to be
connected to the Smartpack controller’s USB or Ethernet port.

CONTROLLER WITH DISPLAY

The Smartpack controller
The 30V Micropack SRB can be configured with the Smartpack controller.
Smartpack is situated in the front next to the rectifiers. It will by default
show output voltage and battery and load current. More monitoring fields
can also be shown. It also allows for local setup of the power system
without the need of a PC and web browser.

…more monitoring connections

In addition to the display the Smartpack controller can be extended with a
number of Controller CAN nodes as IO Monitors, Battery monitor, AC Mains
monitor and Load monitor.

Eltek — Gråterudveien 8, PB 2340 Strømsø, 3003 Drammen, Norway Phone: +47 32 20 32 00 Eltek © 2017 – www.eltek.com
MICROPACK SRB 30VDC 960W
Model Micropack SRB 30VDC 960W / 24Ah
Part number CU0403.003
INPUT DATA DC
Voltage 1 x single phase feed (85 Vac – 300 Vac)
Recommended input breaker C10A (optional)
Internal fuses in rectifier module
Input protection
On/Off MCB
OUTPUT DATA
Voltage 30VDC on output terminals. 34,05V on batteries
(max rect adj. 21,5V – 36V) With drop diodes and bypass relay for battery
Output current Max. 40A/24V > 32A/30V (4 modules)
See previous page or Micropack rectifiers datasheets
CONNECTIONS
Load connection 12 pin connector for load connection for positive and negative.
Battery connections Terminal blocks, up to 16 mm2 (max 3 x 24Ah of SB 12-6L batteries)
Temperature sensor Rear connection for int/ext
Alarm connections Pluggable terminal blocks; up to 1.5 mm2
Network/TCP/IP RJ45 female on back panel
Input AC Std. Europlug (Male)

CONTROL AND MONITORING - DEFAULT

Monitoring Unit Smartpack WEB/SNMP
Local Operation WEB interface via standard browser using WebPower
Remote Operation WebPower (WEB Interface, SNMP protocol and email of alarms)
Alarm Relays 3 x Potential free change over contacts (NO, NC, C)
[Max 75V/2A/60W]
Inputs 3 x multipurpose inputs. Can be configured for temperature measurement,
digital or analogue monitoring
OPTIONAL MONITORING – DISPLAY & MORE FUNCTIONALITY
Monitoring Unit Smartpack
SNMP/Web
Extra features compared to a internal Compack:
Local Operation 2 x 16 char LCD screen; 3 – buttons, keypad USB
Alarm Relays 6 x Potential free change over contacts (NO, NC, C) [Max 75V/2A/60W]
Inputs 6 x multipurpose inputs
Full support of the Controller CAN nodes (power provided)

OTHER SPECIFICATIONS
Isolation 3.0 KVAC – input to output
1.5 KVAC – input to earth
0.5 KVAC – output to earth
Temperature Operating: -25 to + 40°C (- 4 to +104°F) * full power
Storage: -25 to + 40°C (- 4 to +104°F) *
* Due to internal batteries
Dimensions & Weight 488 x 520x130mm (W x D x H) + 19”brackets; Approx. 22kg (ex. rectifiers)
DESIGN STANDARDS
ElectricalsSafety IEC 60950-1
EMC ETSI EN 300 386 V.1.3.2 (télécommunication network)
EN 61000-6-1 (immunity, light industry)
EN 61000-6-2 (immunity, industry)
EN 61000-6-3 (emission, light industry)
EN 61000-6-4 (emission, industry)
EN 61000-6-5 (immunity, power stations and sub stations) *
ORDERING INFORMATION
CU0403.003 UP 30V 0.96kW 1x230V 19"
CU0403.002 (old version) UP 30V 0.96kW 1x230V 19"
241120.200 Micropack 24/240 WOR
242100.118 Smartpack controller
1) Allow for minimum 1U below and above to ensure airflow

CU0403.003.DS3 – rev1 Specifications are subject to change without notice

Eltek — Gråterudveien 8, PB 2340 Strømsø, 3003 Drammen, Norway Phone: +47 32 20 32 00 Eltek © 2017 – www.eltek.com