Humbucking Pickups - How They Work

We should first explain two properties of pickups which were

never previously discussed -
magnetic polarity and coil windings.
Two pickups can be combined with these two properties in four
ways:

****** Magnetic Polarity Coil Windings Output Hum Canceling

1) Same Same Strong No

2) Opposite Opposite Strong Yes

3) Same Opposite Weak Yes

4) Opposite Same Weak No

The rightmost columns "Output" and "Hum Canceling" will be discussed later.

Combination number 1 is the way in which guitar pickups have

been manufactured and installed ever since the very first electric
guitar. This was (and still is), a pretty good way to wire guitars with
the only problem being hum.
Guitar pickups are wound with a lot of wire which unintentionally
creates an "antenna" which can "receive" electromagnetic
interference from fluorescent lights, light dimmers, electronics
equipment and especially 60 cycle AC hum. Generally, guitar
players have learned to live with this interference by avoiding
playing near electrical equipment and by facing in a direction in
which the guitar produces the least noise.

Humbucking Pickups
Combination 2
Opposite Magnetic Polarity Opposite Coil Windings

Probably the most successful attempt in reducing pickup noise

was in 1955 when Gibson Guitar employee Seth Lover developed
the humbucking pickup. These pickups are actually two side by
side, single coil pickups with each coil differing from the other by
having reverse winding and reverse magnetic polarity (abbreviated
as "RWRP"). Humbucking pickups can have more than one
magnet, but to keep things simple, let's see how a single magnet
humbucker works.

Did you notice that the magnet in the drawing has its polarity on
its edges instead of on its ends? This is done to keep the magnetic
strength constant from one end of the magnet to the other
permitting all 6 guitar strings to have the same volume.

The other reason for polarizing the edges is to allow both coils to
have opposite magnetic polarities which the diagram below easily
demonstrates.
Moving on to the coils, both are shown with windings going in
a clockwise direction. However, shouldn't those coil windings be
the reverse of each other? Not exactly. Basically the term "reverse
winding", although it is used by just about everybody, is
inaccurate. Actually, it is the current flow in the two coils that
travel in opposite directions.

In the diagram, the current begins at the center of coil 1 then

travels clockwise until it reaches the series connection(the place
where the two coils join - indicated by the blue arrow). The current
enters coil 2 at point C and if we follow it to point D, we see that
the current has traveled in a counter-clockwise direction. This is
what makes humbucking pickups work the way they do.
Coil 1 and coil 2 are electrically out of phase and since electrical
interference only travels through the guitar pickup's windings,
when the hum travels from one coil to the other, it gets canceled
due to the opposite coil windings. (The magnets play no part in
hum cancelation.)

Unlike hum, an electric guitar's sound (the signal) is generated

from the pickup's wiring and magnets. So, when the guitar signal
travels through the coils, no cancelation occurs because the coils
are out of phase electrically andmagnetically.
In effect, having opposite electrical and magnetic polarities is
similar to putting two phase switches on two pickups. When both
switches are set to the out of phase positions, no cancelations
occur because the 2 "out of phase" conditions cancel each other
out.

Anyway, if you just wanted to learn how humbucking pickups

work, you don't have to read any further. However, you might find
it interesting to continue.
The above graphic shows a humbucking pickup wired in series
and connected in what I call an "inside-out" wiring. The wires that
were joined at the series connection are now on the "outside" of
the pickup and the 'A' and 'D' wires now meet at the series
connection. But is this humbucking? Well, both coils have
opposite magnetic polarity and just as in the previous example,
when the current in coil 1 travels in a clockwise direction, it
travels counter-clockwise in coil 2. Since we have opposite
magnetic polarity and opposite coil windings (actually current
flow), this is just as valid as if it were wired in the conventional
way.
Why would we want to wire it in this way? Among other things, it is
something to consider when you choose to addcoil cut
switching to the wiring.
The above graphic shows a humbucking pickup wired in parallel.
The important features of parallel wiring are:
• it produces a brighter sound than series wiring and
• it is humbucking.
In this wiring, the 'A' and 'C' wires are connected to '+' and to each
other. The 'A' wire begins at the "START" in coil 1, and travels
clockwise. The 'C' wire begins at the "FINISH" of coil 2 and travels
in a counter-clockwise direction.
The 'B' and 'D' wires are also connected and if we follow those
wires, 'B' enters coil 1 in a counter-clockwise direction and 'D'
goes from the center of coil 2 in a clockwise direction.
So, as we can see, in both cases we have a reverse current flow
and since we have opposite magnetic polarities, this is a properly
wired humbucking circuit.

Even the Fender Guitar Company started making their guitars

humbucking, but not with traditional humbucking pickups.
Before the mid 1980's, if you had a single coil guitar, all its pickups
had the same magnetic properties and all were connected so that
the current flow in each was exactly the same.
By now, you should know why this does not produce a hum-
canceling circuit. (remember combination 1?)

Then, around 1985, the Fender Guitar Company thought of an easy

and inexpensive way to solve the hum problem by making the
middle pickup in a Fender Stratocaster™ have reverse wiring and
reverse polarity of the other 2 coils. This in effect "created" a
humbucking pickup whenever someone selected two pickup
combinations - neck and middle ormiddle and bridge.

Still, this left the neck and bridge pair in a non-hum-canceling

status, which didn't bother too many people because the "neck
and bridge" choice is not available for a standard Fender
Stratocaster™.

Combination 3
Same Magnetic Polarity Opposite Coil Windings

Since humbucking pickups always have two coils

with opposite magnetic polarities when would we be connecting
two pickups with similar magnetic polarities? How about when
connecting the neck and bridge pickups of a Fender
Stratocaster™?

Looking at the diagram we see that connecting A to C and B to D

(the typical parallel wiring method) creates a circuit in which the
current flows through the coils in opposite directions, ensuring the
hum will get canceled. However, we also need (but don't have)
opposite magnetic polarities to counteract the electrical out of
phase guitar signal. Basically, we have a circuit in which the
hum and the guitar signal gets canceled. The guitar signal doesn't
get 100% canceled (just as the hum doesn't get 100 % canceled
either) and so the guitar signal has been reduced to a weak, thin,
squawky "out of phase" sound. Actually, some people like this
sound. It is used quite often in country music and produces a
penetrating sound when used through distortion. It is not a sound
you would want to have all the time but that's why there are
switches on guitars.

The above graphic shows a series wiring of this humbucking

circuit. This one, due to its greater volume is more popular than a
parallel out of phase circuit.

Combination 4
Opposite Magnetic Polarity Same Coil Windings

Of all four combinations, this is undoubtedly the worst of the

bunch. It produces a weak guitar signal that isn't even hum
canceling.
If you wired a humbucking pickup out of phase, this is the result.
You've probably seen books and other websites that state that this
produces a poor sound because the coils of a humbucking pickup
are so close to each other. No, I believe the problem is the lack of
hum canceling and the rather weak guitar signal. Together, these
produce a very poor signal to noise ratio.
Our recommendation is not to try this combination at all, whether
in a humbucking pickup or two separate pickups.

Well, now that you have become a humbucking "scholar", maybe

your next guitar project will not seem so overwhelming.

Return To Guitar Wiring Page 1

Return To Home Page

Copyright © 1999 - 2014 1728 Software Systems
!