Scribd
Upload
3 views

Machine Design-II (2)

Uploaded by

kanefernandess66
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3 views

Machine Design-II (2)

Uploaded by

kanefernandess66
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DR.

BABASAHEB AMBEDKAR TECHNOLOGICAL UNIVERSITY, LONERE


Supplementary Examination – Summer 2022
Course: B. Tech. Branch : Mechanical Semester :II
Subject Code & Name:BTMEC602, Machine Design - II
Max Marks: 60 Date: Duration: 3 Hr.
Instructions to the Students:
1. All the questions are compulsory.
2. The level of question/expected answer as per OBE or the Course Outcome (CO)
on which the question is based is mentioned in ( ) in front of the question.
3. Use of non-programmable scientific calculators is allowed.
4. Assume suitable data wherever necessary and mention it clearly.
(Level/CO Marks
)
Q. 1 Solve Any Two of the following.
A) Derive stribeck equation for static load carrying capacity of bearing CO3 06
B) The radial Fr=2500N for first five revolution reduces to 1500N for next ten CO4 06
revolution. Variation of load is repetitive; The expected life of the bearing is
25 million revolutions. Determine dynamic load carrying capacity of bearing
C) Discuss in detail about Viscosity and its measurement of lubricant CO2 06

Q.2 Solve Any Two of the following.


A) Compare Hydrostatic and Hydrodynamic bearing CO3 06
B) What is Destructive pitting and Scoring failure of gear CO2 06
C) Discuss virtual number of teeth for helical gear with neat sketch CO4 06

Q. 3 Solve Any One of the following.


A) A spur gear pair is to transmit 8KW power at 750 rpm to another machine at CO5 12
300 rpm. Material for both the gears are same having ultimate tensile
strength is 620 MPa. Surface hardness is 330 BHN. Pinion has 20 teeth,
module is 5mm and face width is 60 mm service factor is 1.5 mm and load
concentration factor is 1.4. Determine the factor of safety in bending and
wear a) by considering the velocity factor accounts for dynamic load b) by
considering dynamic load using Buckingham equation. Velocity factor =
3/(3+V), Tooth profile error is 0.05 mm, tooth form factor = 0.111.
E=2.1x105 MPa.
B) Write short note on CO5 12
a) Thermal consideration of worm and worm wheel
b) Selection of material for worm and worm wheel
C) A bevel gear pair consists of 20 teeth on pinion meshing with 44 teeth gear, CO5 12
pinion and gear having ultimate tensile strength are 680 MPa and 600 MPa
respectively. Pinion transmits 15 KW at 1500 rpm. Service factor 1.75,
factor of safety 1.5, surface hardness 350 BHN for both gears. Assume the
velocity factor accounts for dynamic load. 𝐶𝑣 = 5.6/(5.6+√𝑣 ). Design a gear
pair

Q.4 Solve Any Two of the following.


A) The leather belt drives transmit 15 KW of power by open belt. The center CO5 06
distance between the pulleys is twice the diameter of bigger pulley. The belt
should operate at velocity of 20 m/s approx. and the stress in the belt should
be 2.25 MPa. The thickness of belt is 5 mm. Calculate the diameter of
pulleys the length and width of the belt and the belt tension.
B) State polygonal effect in chain drive with neat sketch CO4 06
C) What is stresses in disc and armed flywheel CO3 06

Q. 5 Solve Any One of the following.


A) A centrifugal clutch transmits 25 KW power at 900 rpm. The speed at which CO4 12
engagement begins is 70% of the running speed. The inner radius of drum is
15 cm and the radial distance of centre of gravity of shoe beam the axis of
rotation of the spider in engaged position is 12 cm. Determine mass of each
shoe. Take number of shoes as four and coefficient of friction is 0.25 and
intensity of pressure is 0.1 MPa.
B) Discuss Shoe brake for line of action passes through fulcrum of lever and CO4 12
below and above at a distance a w.r.t fulcrum
C) A cylinder diameter is 200 mm closed on both its ends is withstanding CO6 12
internal pressure of 20 MPa. Ultimate and yield strength is 440MPa and
240MPa respectively and factor of safety is 1.5 and poisons ration is 0.3.
Determine thickness of cylinder based on maximum principal stress theory,
maximum principal strain theory, maximum shear stress theory and
maximum distortion energy theory.
*** End ***
The grid and the borders of the table will be hidden before final printing.

You might also like