ELECTRIC

Height Adjustable TV Stand

ASSEMBLY INSTRUCTIONS

Model No : CTD-TV2-4F2
 Component Checking-list
A TV Stand Base 1pc O Screw M6*16 8pcs

B Column 2pcs P Screw M5*10 10pc

C Tilting Frame Group 1pc Q Universal wheel 4pcs

D Rack 2pcs R 4mm Wrench 2pcs

E Flip Fixed Part 1pc S 3mm Wrench 2pc

F Fixed Cover 1pc T 5mm Wrench 1pcs

G Bottom Cover 1pc U Cross Screwdriver 1pc

H Control Box 1pc V Clip UC-1 2pcs

I Hand display 1pc W Clip UC-4 2pcs

J Remote 1pc X Shock Pad 2pcs

K Power Line 1pc Y Lock Screw 1pc

L Core Patch Cord 1pc Z Screw M4*6 4pcs

M Spring Patch Cord 1pc a Screw M8*12 16pcs

Screw
N Screw M6*10 16pcs b Standby Screw Bag 1pc
Bag
 1 Fix Four Universal Wheels With Base

Q【x4】
Universal wheel

A【x1】 T【x1】
TV Stand Base 5mm Wrench

a【x16】
Screw M8*12
2 Installing The Column and TV Stand Base

N【x12】
Screw M6*10
R【x1】
4mm Wrench

B【x2】
Column
 3 Connect Control System With Column

L【x1】
Core Patch Cord

I【x1】
Hand display

K【x1】 W【x2】
Power Line Clip UC-4

U【x1】
Cross Screwdriver
M【x1】
Spring Patch Cord Z【x2】
Screw M4*6

Note: M1 and M2 interfaces are

S【x1】 G【x1】
3mm Wrench Bottom Cover

P【x10】
Screw M5*10
 5 Fix TV Holder With Bracket

R【x1】
D【x2】 O【x8】
4mm Wrench
Rack Screw M6*16

C【x1】
Tilting Frame Group
1

X【x2】
U【x1】 Shock Pad
Cross Screwdriver

E【x1】
Flip Fixed Part
 6 Install The Push Rod Rollover Assembly

S【x2】
Y【x1】 3mm Wrench
Lock Screw

Z【x2】
Screw M4*6

N【x4】
Screw M6*10
V【x2】
Clip UC-1
R【x1】
4mm Wrench

U【x1】
Cross Screwdriver F【x1】
Fixed Cover
 7 Operation Manual

【1】Remote Control

Digital Up Down Setup Memory1 Memory2 Flip forward Leech Back

Up

Down

Flip Forward

Leech Back
【3】Remote control matching

Within 5 seconds after the control box is powered on, press the remote controller A, B, C, and D one by one. When
pressing the button, there will be a beep sound.

【4】Reset Operation

First of all, after the product installation and control system connection are completed, long press and hold the “﹀”
button, the system enters the initialization mode, the initial height is displayed from RST to initial height, the reset is
successful.

【5】The column stops operation

Remote Controller: When the column during rising, you want to stop it, then you can press the button "A" ，the
column will stop to rise. And if necessary to stop the column during the descent, you can press the button "B"，it will
stop to go down.

Hand Controller: When the column stops running, first press the "S" button to display "S-", and then press any of
the buttons of "1" and "2" on the hand controller. At this time, the position of the column will be remembered. "1" and
"2" on the hand controller mean that the hand controller can remember 2 different column positions, and can be
repeated memory, the position is still saved after power failure! After the position of the column is remembered,
operate the hand controller and press the memory position button "1", and the column will automatically move to the
memorized position; If you want to stop the column during its operation, press the "︿" or "﹀" button on the hand
controller!

【8】Operation System Protection:

After the lift runs continuously for 3~4 times ,the controller will in protection position. The hand display show “HOT”,At this
time ,the remote control ,and hand display will be invalid , After 18mins, the automatic connect or direct power off ( power
off refers to the adapter indicator light goes out )

Precautions:

1) The product shall be used in accordance with the technical parameters ;

2) Keep away from corrosive gas and dusty environment, pay attention to waterproof;

When the indicator light of the hand display show red ,it needs to be reset before it can be used normally