Cube 0.

8L Electronic Series II
Induct Installation
Electronic Activation Urinal The operation flow pressure of the valve is
Suite Installation Instructions 300 to 500 kPa (30 to 50 metre head) to
achieve a minimum flow to the valve of 18 litres/minute
necessary to flush the urinal.
IMPORTANT: The lines must be flushed prior to installing solenoid valve. Allow access for the
connection and 20mm dia. Inlet Minimum supply diameter of
servicing of all (not supplied) nominal 20mm is required to the valve.
1. Install flush valve as required, inwall (Fig. 1), induct (Fig. 4) or inceiling (Fig. 5).
electrical components
IMPORTANT: Flush valve must be installed vertically. Flush 1.8m power lead
2. Connect water supply and flushpipe. Flushpipe must be vertical and straight Sensor control unit
otherwise water back up can occur. 1/2” BSP
3. IMPORTANT: Fit flexible electrical conduit pipe for sensor cable without kinks, Power supply unit
1.8m power lead Mode
(not supplied). Solenoid valve
4. The operation flow pressure of the valve is 300 to 500 kPa (30 to 50 metres

0.5m min.
Sensor cable

3m max.
head) to achieve a minimum flow to the valve of 18 litres / minute necessary to 3.5m
flush the urinal.
Refer to instruction Copper flush pipe
5. Remove brass protective plug and install the Solenoid Valve into position. manual for details on Inlet centre
(nominal 20mm)
6. Make connection from Solenoid Valve to sensor control unit. configuring controller
7. Mount Sensor Control Unit, as detailed in Fig. 1. settings.
8. Make connection from Power Supply Unit to Sensor Control Unit as detailed in
Power Sensor control unit
Fig. 2. DO NOT SWITCH ON POWER SUPPLY.

458
supply
9. Clean rectangle pad area at the back of the urinal ensuring it is free of dust

400 accessible application height

unit Sensor
3/4” BSP
and grease. Apply mastic glue supplied to the black plastic side of the Sensor

405 accessible application height

D.167 Concealed Fixing Bracket
Sensor

615 approx. standard height

(opposite side to the label). Adhere Sensor on the urinal with cable pointing Nominal 20mm

610 standard height

Copper flushpipe 80
upwards, as detailed in Fig. 3. Connect Sensor Control Unit Connector as 20mm min. keeseal
(not supplied) 2° Slope
detailed in Fig. 2.

371 standard height

161 disabled height
P-trap outlet centre
10. Ensure correct connections are made prior to installing urinal. Important:
Switch ON Power supply. Install 20mm or
Note: Surge protectors are recommended to avoid power spikes affecting the 25mm flexible
life of the transformer and the electronic control module. Transformers should electrical conduit pipe for
the entire length of the
not be plugged in until all major electrical work has been completed on site. sensor cable. Finished Floor
Note: Unit is factory preset to discharge 0.8 litres at 300 - 400kPa inlet Failure to comply will
pressure. If the inlet pressure is 401 - 500kPa, press and hold controller void warranty.
FLUSH button for 5 seconds to change the pressure setting. Fig. 4
Sensor cable 3.5m
See instruction manual for complete details.
11. Suggested onsite method of determining discharge volume of 0.8 litres Sensor control
per flush. unit connector Sensor Inceiling Installation
Activate the flush valve by waving your hand in front of the Sensor.
Minimum supply diameter of
Discharge the water through a hose into a container and measure the Sensor control unit
Sensor pad nominal 20mm is required to the valve Sensor control unit
discharge volume.
12. Install the urinal and check for leaks. 1.8m power lead
Black
13. Install optional cover plate on inwall installation only. mastic
glue Power supply unit
Note: Refer to Caroma technical manual for more information. 1.8m power lead

Sensor
Fig. 3
Fig. 2 Access to service valve
is required

Inwall Installation

0.5m min.
Stop Cock Minimum cavity

3m max.
thickness of 100mm
Open
Minimum supply diameter of Copper flushpipe
nominal 20mm is required to the valve (nominal 20mm)
Sensor cable
Optional cover plate 3.5m
Sensor control unit Code No. 678811

Sensor cable Sensor control unit

0.5m min.
3m max.

3.5m

Copper flush pipe Inlet centre

(nominal 20mm) Inlet centre
Sensor

458
400 accessible application height
Sensor
458

Sensor

405 accessible application height

400 accessible application height

D.167 Concealed Fixing Bracket

D.167 Concealed Fixing Bracket

615 approx. standard height

Sensor

610 standard height

80
615 approx. standard height
405 approx. disabled height

80
610 standard height

2° Slope

371 standard height

161 disabled height
2° Slope

P-trap outlet centre

371 standard height
161 disabled height
P-trap outlet centre

Finished Floor
Finished Floor

Fig. 1 Fig. 5
Issue No: 2
Date of Issue: 02.10.15