0% found this document useful (0 votes)
6 views85 pages

IBM System Storage SAN06B-R Installation, Service and User's Guide

The IBM System Storage SAN06B-R Installation, Service, and User Guide provides essential information for the installation, service, and operation of the SAN06B-R device. The third edition includes updates on clean optics for higher transmission speeds, link troubleshooting, and other minor content changes. It also emphasizes accessibility features and provides resources for obtaining further support and documentation.

Uploaded by

tangzqwh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
6 views85 pages

IBM System Storage SAN06B-R Installation, Service and User's Guide

The IBM System Storage SAN06B-R Installation, Service, and User Guide provides essential information for the installation, service, and operation of the SAN06B-R device. The third edition includes updates on clean optics for higher transmission speeds, link troubleshooting, and other minor content changes. It also emphasizes accessibility features and provides resources for obtaining further support and documentation.

Uploaded by

tangzqwh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 85

IBM System Storage SAN06B-R 

Installation, Service, and User Guide


Service information: 2498 / R06

Read Before Using


This product contains software that is licensed under written license agreements. Your use of such software is subject to
the license agreements under which they are provided.

GC27-2270-02
IBM System Storage SAN06B-R 

Installation, Service, and User Guide


Service information: 2498 / R06

GC27-2270-02
Note:
Before using this information and the product it supports, read the information in “Notices” on page 47.

Copyright © 2009-2010 Brocade Communications Systems, Inc. All Rights Reserved.


The following paragraph does not apply to any country (or region) where such provisions are inconsistent with
local law.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states (or
regions) do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement
may not apply to you.
© Copyright IBM Corporation 2009, 2013.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Read this first
Summary of changes
| This is the third edition of the IBM System Storage SAN06B-R Installation, Service,
| and User Guide. The content changes since the last edition of this publication are
| noted by a vertical line placed in the left margin beside each change. Minor edits
| are not identified by this mark. A summary of the changes for each edition are
| listed below.

| Third edition
| The following changes were made in the third edition:
| v Addition of information regarding the need for clean optics with higher
| transmission speeds.
| v Addition of information for link troubleshooting
| v Other minor content updates

Second edition
The following changes were made in the second edition:
v Additional optional FICON Accelerator feature
v Additional optional Server Application Optimization (SAO) feature
v Minimum Fabric Operating System (FOS) was changed to 6.4.

Getting help
For the latest version of your product documentation, visit the web at
www.ibm.com/shop/publications/order. Search by form number or title.

For more information about IBM® SAN products, see the following Web site:
www.ibm.com/servers/storage/san/

IBM Redbooks® often provide in depth information about product best practices,
configurations, and more technical information. For redbooks associated with this
product, enter search terms on the following Web site: www.redbooks.ibm.com/.

For support information for this and other IBM products, see the IBM Support
Portal, www.ibm.com/supportportal. Search for the product Machine type or
product name.

For Fabric OS Release Notes and access to Fabric OS firmware downloads, go to


the IBM Support Portal, www.ibm.com/supportportal. Search for the product
Machine type or product name, and then follow links for Downloads. More
detailed instructions are available through the Accessing firmware updates and
OS documentation updates link on the product documentation CD that is shipped
with this product.

You can also contact IBM within the United States at 1-800-IBMSERV
(1-800-426-7378). For support outside the United States, you can find the service
number at: www.ibm.com/planetwide/.

© Copyright IBM Corp. 2009, 2013 iii


Visit www.ibm.com/contact for the contact information for your country or region.

For detailed information about the Fibre Channel standards, see the Fibre Channel
Industry Association (FCIA) Web site at: www.fibrechannel.org/

For information about storage industry standards, see the Storage Networking
Industry Association (SNIA) Web site at: www.snia.org/

Taiwan Contact Information


IBM Taiwan Product Service Contact Info:
IBM Taiwan Corporation
3F, No 7, Song Ren Rd., Taipei Taiwan
Tel: 0800-016-888

Accessibility features for the SAN06B-R


Accessibility features help users with restricted mobility or limited vision
successfully use information technology products. IBM strives to provide products
with usable access for everyone, regardless of age or ability. This product uses
standard Windows navigation keys.

Accessibility features
The following list includes the major accessibility features in this product:
v Light emitting diodes (LEDs) that flash at different rates, to represent the same
information as the colors of the LEDs
v Industry-standard devices for ports and connectors
v Management of the product through management applications is available
through Web and Graphical User Interface (GUI) options

Keyboard navigation
This product does not have an attached or integrated keyboard. Any keyboard
navigation is provided through the management software and GUI. This product
uses standard Microsoft Windows navigation keys. You can navigate the software
and the product documentation from the keyboard by using the shortcut keys for
your browser or screen-reader software. See your browser or screen-reader
software Help for a list of shortcut keys that it supports.

Vendor software
This product includes certain vendor software that is not covered under the IBM
license agreement. IBM makes no representation about the accessibility features of
these products. Contact the vendor for the accessibility information about its
products.

Related accessibility information


You can view the publications for this product in Adobe Portable Document
Format (PDF) using the Adobe Acrobat Reader. The PDFs are provided on a

iv SAN06B-R Installation, Service, and User Guide


product documentation CD-ROM that is packaged with the product. The CD-ROM
also includes an accessible HTML version of this document.

IBM and accessibility


See the IBM Human Ability and Accessibility Center web site at
www.ibm.com/able/ for more information about the commitment that IBM has to
accessibility.

How to send your comments


Your feedback is important in helping us provide the most accurate and
high-quality information. If you have comments or suggestions for improving this
document, send us your comments by email to [email protected]. Be sure to
include the following information:
v Exact publication title
v Form number (for example, GC27-2270-00)
v Page numbers to which you are referring

You can also mail your comments to:


International Business Machines Corporation
Information Development
Department GZW
9000 South Rita Road
Tucson, Arizona 85744-0001 U.S.A.

When you send information to IBM, you grant IBM a nonexclusive right to use or
distribute the information in any way it believes appropriate without incurring any
obligation to you.

Read this first v


vi SAN06B-R Installation, Service, and User Guide
Contents
Read this first . . . . . . . . . . . . iii Setting the switch date and time . . . . . . 19
Summary of changes . . . . . . . . . . . iii Configuring FCIP and Fibre Channel routing
| Third edition . . . . . . . . . . . . . iii services. . . . . . . . . . . . . . . 20
Second edition . . . . . . . . . . . . iii Installing SFPs . . . . . . . . . . . . 21
Getting help . . . . . . . . . . . . . . iii Connecting cables . . . . . . . . . . . 21
Taiwan Contact Information . . . . . . . . iv Verifying correct operation of the switch. . . . 22
Accessibility features for the SAN06B-R . . . . . iv Backing up the configuration . . . . . . . 23
Accessibility features . . . . . . . . . . iv Managing license keys (optional) . . . . . . . 23
Keyboard navigation . . . . . . . . . . iv Viewing current license keys. . . . . . . . 24
Vendor software . . . . . . . . . . . . iv Adding a license key . . . . . . . . . . 24
Related accessibility information . . . . . . iv Removing a license key . . . . . . . . . 24
IBM and accessibility . . . . . . . . . . v
How to send your comments . . . . . . . . . v Chapter 3. Operating the SAN06B-R . . 25
LED activity . . . . . . . . . . . . . . 25
Figures . . . . . . . . . . . . . . . ix LEDs on the port side of the switch . . . . . 25
LEDs on the nonport side of the switch . . . . 29
Tables . . . . . . . . . . . . . . . xi Interpreting POST results . . . . . . . . . . 30
Diagnostics and troubleshooting . . . . . . . 31
Diagnostic tests . . . . . . . . . . . . 31
Safety and environmental notices . . . xiii CRU status . . . . . . . . . . . . . 31
Safety notices and labels . . . . . .
. xiii . . . Powering off the switch . . . . . . . . . 34
Danger notices . . . . . . . .
. xiii . . . Removing the battery . . . . . . . . . . 34
Caution notices . . . . . . . .
. xvi . . .
Safety labels . . . . . . . . . . . . xviii
Appendix A. Product specifications . . 37
Attention notices . . . . . . . . . . . xviii
Summary of switch components . . . . . . . 37
Rack safety . . . . . . . . . . . . . . xix
Weight and physical dimensions . . . . . . . 37
Rack installation . . . . . . . . . . . xix
Power supply . . . . . . . . . . . . . 38
Rack relocation (19" rack). . . . . . . . . xx
Environmental requirements . . . . . . . . . 38
Product recycling and disposal. . . . . . . . xxi
Data transmission ranges . . . . . . . . . . 39
Memory specifications . . . . . . . . . . . 40
About this document . . . . . . . . xxiii Port specifications . . . . . . . . . . . . 40
Product documents . . . . . . . . . . . xxiii Fibre Channel port specifications . . . . . . 40
Brocade documents . . . . . . . . . . . xxiii GbE port specifications . . . . . . . . . 40
IBM and Brocade product matrix . . . . . xxiv Serial port specifications . . . . . . . . . 40
Parts list (CRUs). . . . . . . . . . . . . 41
Chapter 1. Introducing the SAN06B-R . . 1
SAN06B-R features . . . . . . . . . . . . 2 | Appendix B. Link troubleshooting . . . 43
Available licenses . . . . . . . . . . . . . 3 | Fault isolation . . . . . . . . . . . . . 43
Port side of the switch . . . . . . . . . . . 3 | Dust, dirt, or other contaminants . . . . . . . 44
Nonport side of the switch . . . . . . . . . 4 | Best practices for minimizing link loss . . . . . 44
SAN06B-R management . . . . . . . . . . 5 | Attenuation on LWL connections . . . . . . . 45
| Best Practice for LWL connections – Optically
Chapter 2. Installing and configuring the | engineer a long-distance connection . . . . . 45
SAN06B-R . . . . . . . . . . . . . . 7 | 2G LWL SFP maximum receive power . . . . 45
Items included with the switch . . . . . . . . 7
Installation and safety considerations . . . . . . 8 Notices . . . . . . . . . . . . . . 47
Setting up the switch as a standalone unit . . . . 8 Trademarks . . . . . . . . . . . . . . 49
Installing in an EIA cabinet . . . . . . . . . 9 Electronic emission notices . . . . . . . . . 50
Time required . . . . . . . . . . . . . 9 Federal Communications Commission (FCC)
Items required . . . . . . . . . . . . . 9 Class A Statement . . . . . . . . . . . 50
Installation instructions . . . . . . . . . . 9 Industry Canada Class A Emission Compliance
Cabling and setting up the switch . . . . . . . 14 Statement . . . . . . . . . . . . . . 50
Planning for cable management . . . . . . 15 Avis de conformité à la réglementation
Items required for setup . . . . . . . . . 15 d'Industrie Canada . . . . . . . . . . . 50
Setting up the switch . . . . . . . . . . 15

© Copyright IBM Corp. 2009, 2013 vii


European Union EMC Directive Conformance Korea Communications Commission (KCC)
Statement . . . . . . . . . . . . . . 50 Statement . . . . . . . . . . . . . . 52
Germany Electromagnetic Compatibility Directive 51 Russia Electromagnetic Interference (EMI) Class
People's Republic of China Class A Electronic A Statement . . . . . . . . . . . . . 53
Emission Statement . . . . . . . . . . . 52 Australia and New Zealand Class A Statement 53
Japan VCCI Council Class A Statement . . . . 52
Japan Electronics and Information Technology Index . . . . . . . . . . . . . . . 55
Industries Association (JEITA) Statement . . . 52

viii SAN06B-R Installation, Service, and User Guide


Figures
1. Port side view . . . . . . . . . . . . 3 8. Inserting slides into the rack rails . . . . . 14
2. Port numbering . . . . . . . . . . . 4 9. LEDs on port side . . . . . . . . . . 26
3. Nonport side of the switch . . . . . . . . 4 10. Nonport side components. . . . . . . . 29
4. Rack assembly . . . . . . . . . . . 10 11. Power supply/fan locations . . . . . . . 32
5. Separating the inner and outer rails. . . . . 11 12. Orientation of the power supply and fan
6. Mounting the moving portion of the slide and assembly . . . . . . . . . . . . . 33
mounting brackets to the switch . . . . . 12 13. Location of battery holder. . . . . . . . 35
7. Mounting the fixed portion of the rail and the | 14. Identifying the origin of failure . . . . . . 43
locking brackets to the rack . . . . . . . 13

© Copyright IBM Corp. 2009, 2013 ix


x SAN06B-R Installation, Service, and User Guide
Tables
1. Sample caution notices . . . . . . . . xvi 13. Power supply/fan status LED patterns 30
2. Brocade and IBM product and model 14. Switch dimensions . . . . . . . . . . 37
number matrix . . . . . . . . . . . xxiv 15. Power supply specifications . . . . . . . 38
3. Feature comparison - base model and with the 16. Environmental requirements . . . . . . . 38
upgrade license . . . . . . . . . . . 2 17. Fibre channel data transmission ranges by
4. Management options . . . . . . . . . . 5 cable type and port speed. . . . . . . . 39
5. Parts supplied with the rack-mount kit 10 18. Gigabit Ethernet data transmission ranges 39
6. tsTimeZone command parameter values 20 19. Copper cabling and RJ-45 data transmission
7. Power status LED patterns . . . . . . . 27 ranges . . . . . . . . . . . . . . 39
8. System status LED patterns . . . . . . . 27 20. Serial cable pinouts . . . . . . . . . . 40
9. Management port LED patterns . . . . . . 27 21. CRU part numbers . . . . . . . . . . 41
10. FC port status LED patterns . . . . . . . 28 | 22. Specifications of LWL 10km transceivers 45
11. GbE optical port status LED patterns . . . . 28 | 23. Maximum receive power of 2 Gbps LWL SFPs 46
12. GBE copper port status LED patterns . . . . 29

© Copyright IBM Corp. 2009, 2013 xi


xii SAN06B-R Installation, Service, and User Guide
Safety and environmental notices
This section contains information about:
v “Safety notices and labels”
v “Rack safety” on page xix
v “Product recycling and disposal” on page xxi

Safety notices and labels


When using this product, observe the danger, caution, and attention notices
contained in this guide. The notices are accompanied by symbols that represent the
severity of the safety condition. The danger and caution notices are listed in
numerical order based on their IDs, which are displayed in parentheses, for
example (D004), at the end of each notice. Use this ID to locate the translation of
these danger and caution notices in the safety notices publication that is shipped
with this product.

The following notices and statements are used in IBM documents. They are listed
below in order of increasing severity of potential hazards. Follow the links for
more detailed descriptions and examples of the danger, caution, and attention
notices in the sections that follow.
v Note: These notices provide important tips, guidance, or advice.
v “Attention notices” on page xviii: These notices indicate potential damage to
programs, devices, or data.
v “Caution notices” on page xvi: These statements indicate situations that can be
potentially hazardous to you.
v “Danger notices”: These statements indicate situations that can be potentially
lethal or extremely hazardous to you. Safety labels are also attached directly to
products to warn of these situations.
v In addition to these notices, “Safety labels” on page xviii may be attached to the
product to warn of potential hazards.

Danger notices
A danger notice calls attention to a situation that is potentially lethal or extremely
hazardous to people. A lightning bolt symbol accompanies a danger notice to
represent a dangerous electrical condition. Read and comply with the following
danger notices before installing or servicing this device.

DANGER
To prevent a possible shock from touching two surfaces with
different protective ground (earth), use one hand, when possible, to
connect or disconnect signal cables. (D001)

© Copyright IBM Corp. 2009, 2013 xiii


DANGER
Overloading a branch circuit is potentially a fire hazard and a
shock hazard under certain conditions. To avoid these hazards,
ensure that your system electrical requirements do not exceed
branch circuit protection requirements. Refer to the information
that is provided with your device or the power rating label for
electrical specifications. (D002)

DANGER
If the receptacle has a metal shell, do not touch the shell until you
have completed the voltage and grounding checks. Improper wiring
or grounding could place dangerous voltage on the metal shell. If
any of the conditions are not as described, STOP. Ensure the
improper voltage or impedance conditions are corrected before
proceeding. (D003)

DANGER
An electrical outlet that is not correctly wired could place
hazardous voltage on metal parts of the system or the devices that
attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent
an electrical shock. (D004)

The following general electrical danger notice provides instructions on how to


avoid shock hazards when servicing equipment. Unless instructed otherwise,
follow the procedures in the following danger notice.

xiv SAN06B-R Installation, Service, and User Guide


DANGER
When working on or around the system, observe the following
precautions:

Electrical voltage and current from power, telephone, and


communication cables are hazardous. To avoid a shock hazard:
v Connect power to this unit only with the IBM provided power
cord. Do not use the IBM provided power cord for any other
product.
v Do not open or service any power supply assembly.
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an
electrical storm.
v The product might be equipped with multiple power cords. To
remove all hazardous voltages, disconnect all power cords.
v Connect all power cords to a properly wired and grounded
electrical outlet. Ensure that the outlet supplies proper voltage
and phase rotation according to the system rating plate.
v Connect any equipment that will be attached to this product to
properly wired outlets.
v When possible, use one hand only to connect or disconnect
signal cables.
v Never turn on any equipment when there is evidence of fire,
water, or structural damage.
v Disconnect the attached power cords, telecommunications
systems, networks, and modems before you open the device
covers, unless instructed otherwise in the installation and
configuration procedures.
v Connect and disconnect cables as described below when
installing, moving, or opening covers on this product or attached
devices.

To disconnect:
1. Turn off everything (unless instructed otherwise).
2. Remove the power cords from the outlets.
3. Remove the signal cables from the connectors.
4. Remove all cables from the devices.

To connect:
1. Turn off everything (unless instructed otherwise).
2. Attach all cables to the devices.
3. Attach the signal cables to the connectors.
4. Attach the power cords to the outlets.
5. Turn on the devices.
(D005)

Safety and environmental notices xv


Caution notices
A caution notice calls attention to a situation that is potentially hazardous to
people because of some existing condition. A caution notice can be accompanied
by different symbols, as in the examples below:
Table 1. Sample caution notices
If the symbol is... It means...
A hazardous electrical condition with less
severity than electrical danger.

A generally hazardous condition not


represented by other safety symbols.

A specification of product weight that


requires safe lifting practices. The weight
range of the product is listed below the
graphic, and the graphic and the wording of
svc00167

the caution varies, depending on the weight


18-32 kg (39.7-70.5 lbs)
of the device.
18-32 kg (39.7-70.5 lbs)
A potential hazard of pinching the hand or
other body parts between parts.

P/N 18P5850-B
SJ000752

A hazardous condition due to moving parts


nearby.

A hazardous condition due to the use of a


laser in the product. Laser symbols are
always accompanied by the classification of
the laser as defined by the U. S. Department
of Health and Human Services (for example,
Class I, Class II, and so forth).

Read and comply with the following caution notices before installing or servicing
this device.

CAUTION:
Energy hazard present. Shorting may result in system outage and
possible physical injury. Remove all metallic jewelry before servicing.
(C001)

CAUTION:
The battery contains lithium. To avoid possible explosion, do not burn
or charge the battery. Do not: v Throw or immerse into water v Heat to
more than 100°C (212°F) v Repair or disassemble Exchange only with
the IBM-approved part. Recycle or discard the battery as instructed by
local regulations. In the United States, IBM has a process for the
collection of this battery. For information, call 1-800-426-4333. Have the
IBM part number for the battery unit available when you call. (C003)

xvi SAN06B-R Installation, Service, and User Guide


CAUTION:
This part or unit is heavy but has a weight smaller than 18 kg (39.7
lb). Use care when lifting, removing, or installing this part or unit.
(C008)

CAUTION:
The system contains circuit cards, assemblies, or both that contain lead
solder. To avoid the release of lead (Pb) into the environment, do not
burn. Discard the circuit card as instructed by local regulations. (C014)

CAUTION:
This product is equipped with a 3-wire (two conductors and ground)
power cable and plug. Use this power cable with a properly grounded
electrical outlet to avoid electrical shock. (C018)

CAUTION:
This product might contain one or more of the following devices:
CD-ROM drive, DVD-ROM drive, DVD-RAM drive, or laser module,
which are Class 1 laser products. Note the following information:
v Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
v Use of the controls or adjustments or performance of procedures
other than those specified herein might result in hazardous
radiation exposure.
(C026)

CAUTION:
The power-control button on the device does not turn off the electrical
current supplied to the device. The device might also have more than
one connection to dc power. To remove all electrical current from the
device, ensure that all connections to dc power are disconnected at the
dc power input terminals. (C031)

Safety and environmental notices xvii


Safety labels
As an added precaution, safety labels are often installed directly on products or
product components to warn of potential hazards. These can be either danger or
caution notices, depending upon the level of the hazard.

The actual product safety labels may differ from these sample safety labels:

DANGER
Hazardous voltage, current, or energy levels are present inside
any component that has this label attached. Do not open any
cover or barrier that contains this label. (L001)

DANGER
Rack-mounted devices are not to be used as a shelf or work space.
(L002)

DANGER
Multiple power cords. The product might be equipped with
multiple power cords. To remove all hazardous voltages,
disconnect all power cords. (L003)

DANGER
Hazardous voltage present. Voltages present constitute a shock
hazard, which can cause severe injury or death. (L004)

Attention notices
An attention notice indicates the possibility of damage to a program, device, or
system, or to data. An exclamation point symbol may accompany an attention
notice, but is not required. A sample attention notice follows:

Attention: Do not bend a fibre cable to a radius less than 5 cm (2 in.); you can
damage the cable. Tie wraps are not recommended for optical cables because they
can be easily overtightened, causing damage to the cable.

xviii SAN06B-R Installation, Service, and User Guide


Rack safety

Rack installation
DANGER
Observe the following precautions when working on or around your IT rack system:
v Heavy equipment—personal injury or equipment damage might result if
mishandled.
v Always lower the leveling pads on the rack cabinet.
v Always install stabilizer brackets on the rack cabinet.
v To avoid hazardous conditions due to uneven mechanical loading, always install the
heaviest devices in the bottom of the rack cabinet. Always install servers and
optional devices starting from the bottom of the rack cabinet.
v Rack-mounted devices are not to be used as shelves or work spaces. Do not place
objects on top of rack-mounted devices.

v Each rack cabinet might have more than one power cord. Be sure to disconnect all
power cords in the rack cabinet when directed to disconnect power during servicing.
v Connect all devices installed in a rack cabinet to power devices installed in the
same rack cabinet. Do not plug a power cord from a device installed in one rack
cabinet into a power device installed in a different rack cabinet.
v An electrical outlet that is not correctly wired could place hazardous voltage on the
metal parts of the system or the devices that attach to the system. It is the
responsibility of the customer to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock.

(R001 part 1 of 2)
CAUTION:
v Do not install a unit in a rack where the internal rack ambient temperatures will
exceed the manufacturer’s recommended ambient temperature for all your
rack-mounted devices.
v Do not install a unit in a rack where the air flow is compromised. Ensure that air flow
is not blocked or reduced on any side, front, or back of a unit used for air flow
through the unit.
v Consideration should be given to the connection of the equipment to the supply circuit
so that overloading of the circuits does not compromise the supply wiring or
overcurrent protection. To provide the correct power connection to a rack, refer to the
rating labels located on the equipment in the rack to determine the total power
requirement of the supply circuit.
v (For sliding drawers) Do not pull out or install any drawer or feature if the rack stabilizer
brackets are not attached to the rack. Do not pull out more than one drawer at a time.
The rack might become unstable if you pull out more than one drawer at a time.
v (For fixed drawers) This drawer is a fixed drawer and must not be moved for servicing
unless specified by the manufacturer. Attempting to move the drawer partially or
completely out of the rack might cause the rack to become unstable or cause the
drawer to fall out of the rack.

(R001 part 2 of 2)

Safety and environmental notices xix


Rack relocation (19" rack)
CAUTION:
Removing components from the upper positions in the rack cabinet improves
rack stability during relocation. Follow these general guidelines whenever you
relocate a populated rack cabinet within a room or building:
v Reduce the weight of the rack cabinet by removing equipment starting at the
top of the rack cabinet. When possible, restore the rack cabinet to the
configuration of the rack cabinet as you received it. If this configuration is not
known, you must do the following:
– Remove all devices in the 32U position and above.
– Ensure that the heaviest devices are installed in the bottom of the rack
cabinet.
– Ensure that there are no empty U-levels between devices installed in the
rack cabinet below the 32U level.
– If the rack cabinet you are relocating is part of a suite of rack cabinets,
detach the rack cabinet from the suite.
– Inspect the route that you plan to take when moving the rack to eliminate
potential hazards.
– Verify that the route that you choose can support the weight of the loaded
rack cabinet. Refer to the documentation that came with your rack cabinet
for the weight of a loaded rack cabinet.
– Verify that all door openings are at least 760 x 2030 mm (30 x 80 in.).
– Ensure that all devices, shelves, drawers, doors, and cables are secure.
– Ensure that the four leveling pads are raised to their highest position.
– Ensure that there is no stabilizer bracket installed on the rack cabinet
during movement.
– Do not use a ramp inclined at more than 10 degrees.
– Once the rack cabinet is in the new location, do the following:
- Lower the four leveling pads.
- Install stabilizer brackets on the rack cabinet.
- If you removed any devices from the rack cabinet, repopulate the rack
cabinet from the lowest position to the highest position.
– If a long distance relocation is required, restore the rack cabinet to the
configuration of the rack cabinet as you received it. Pack the rack cabinet in
the original packaging material, or equivalent. Also, lower the leveling
pads to raise the casters off of the pallet and bolt the rack cabinet to the
pallet.
(R002)

xx SAN06B-R Installation, Service, and User Guide


Product recycling and disposal
Refer to the IBM Systems Environmental Notices and User Guide (Z125-5823) for
translated environmental statements and information regarding product recycling
and disposal. This document may be provided either in printed version or on the
product documentation CD. See “Removing the battery” on page 34 for
instructions on how to remove the battery.

Safety and environmental notices xxi


xxii SAN06B-R Installation, Service, and User Guide
About this document
This document is intended for use by systems administrators and technicians
experienced with networking, Fibre Channel, and storage area network (SAN)
technologies. It describes how to install, service, and use the IBM System Storage®
SAN06B-R (machine type 2498, model R06). Throughout this document, the
product is referred to as the SAN06B-R extension switch, or simply the switch.

This document has been created to include information specific to SAN06B-R


| switches running on Fabric OS Fabric OS version 7.1.1 and later. For information
| about a Fabric OS version other than 7.1.1, refer to the documentation specific to
your Fabric OS version.

| Note: 7.0.0c is the latest FICON supported release.

Product documents
The following documents contain information related to this product. The
documentation may be printed material or may be on the documentation CD that
is shipped with the product. Newer versions of product documentation may be
available through the IBM Publications Center Web site www.ibm.com/shop/
publications/order. Search by publication title or publication number. Newer
versions may also be available through the IBM Support Portal
www.ibm.com/supportportal. Enter your product machine type (2498) or product
name in the search field, and then select Documentation from the displayed page.
v IBM System Storage SAN06B-R Installation, Service, and User Guide, GC27-2270
(this document)
v Safety Notices
v IBM Environmental Notices and User Guide, Z125-5823
v IBM System Storage SAN06B-R Quick Start Guide, GC27-2271

Brocade documents
IBM b-type switches use software licensed from Brocade Communications Systems,
Inc. You can find information related to the software that supports the director in
the following documents on the CD-ROM supplied with this product:

Brocade Fabric OS
v Fabric OS Administrator's Guide
v Fabric OS Command Reference
v Fabric OS MIB Reference Manual
v Fabric OS Message Reference Manual
v Fabric OS Troubleshooting and Diagnostics Guide
v Fabric OS Fibre Channel over IP Administrator's Guide
v EZSwitchSetup Administrator's Guide
v FICON® Administrator's Guide

Brocade Fabric OS optional features


v Fabric Watch Administrator's Guide

© Copyright IBM Corp. 2009, 2013 xxiii


v Web Tools Administrator's Guide

IBM and Brocade product matrix


When you use any of the Brocade documents, such as Fabric Operating System
(FOS) publications, you will notice that the model numbers reflect the
corresponding Brocade products. Table 2 provides a product matrix for you to use
to correlate the Brocade products and models to the IBM product names and
machine types and model numbers. Products withdrawn from marketing are not
listed.
Table 2. Brocade and IBM product and model number matrix
IBM machine type and
Brocade product name IBM product name model number
Brocade 6520 SAN96B-5 2498 Models F96 and N96
Brocade 6505 SAN24B-5 2498 Model F24, 249824G
Brocade 6510 SAN48B-5 2498 Model F48
Brocade DCX 8510-4 SAN384B-2 2499 Model 416
Brocade DCX 8510-8 SAN768B-2 2499 Model 816
Brocade DCX-4S SAN384B 2499 Model 192
Brocade DCX SAN768B 2499 Model 384
Brocade Encryption Switch SAN32B-E4 2498 Model E32
Brocade 7800 SAN06B-R 2498 Model R06
Brocade 5300 SAN80B-4 2498 Model B80
Brocade 300 SAN24B-4 2498 Models B24 and 24E

xxiv SAN06B-R Installation, Service, and User Guide


Chapter 1. Introducing the SAN06B-R
The SAN06B-R is intended as a platform for Fibre Channel over IP (FCIP). This
enables transmission of Fibre Channel data over long distances via IP networks by
wrapping Fibre Channel frames in IP packets. Each end of the FCIP
communication path must be a compatible FCIP device, either the SAN06B-R or
the FX8-24 blade in a SAN384B or SAN768B chassis.

Refer to the Fabric OS Administrator’s Guide for information on configuring these


features.

The base model of the switch is shipped with six Fibre Channel SFP ports and two
physical Gigabit Ethernet (GbE) ports active. It includes the latest FOS level and is
compatible with the entire IBM b-type switch family. It can operate independently
or in a fabric containing multiple Extension Switches.

A fully licensed SAN06B-R provides the following functionality features:


v FCIP capability
– Up to 8 FCIP tunnels.
– Each FCIP tunnel is represented and managed as a virtual Fibre Channel
E_Port (VE_Port).
– Fibre Channel Routing Services functionality can be used over the FCIP link.
– Fabrics connected through FCIP merge if the ports are configured as
VE_Ports, and do not merge if one end of the connection is configured as a
VEx_Port. If VE_Ports are used in a Fibre Channel Routing Services backbone
fabric configuration, then the backbone fabric merges but the Ex_Port
attached to edge fabrics do not merge. For more information see the Fabric OS
Administrator’s Guide.
v FCIP Trunking with load balancing and network-based failure recovery
v Adaptive Rate Limiting
– Configurable maximum and minimum committed bandwidth per FCIP tunnel
– Minimum rate is guaranteed rate
v FC frame compression before FCIP encapsulation
v Fibre Channel Routing
v SO-TCP with reorder resistance
v FastWrite over FCIP (not over FC)
v Open Systems Tape Pipelining over FCIP
v FICON CUP
v FCIP QoS
v TCP performance graphing in Web Tools

The switch provides the following hardware features:


v Up to 16 Fibre Channel SFP ports supporting Fibre Channel Routing Services
with link speeds up to 1, 2, 4, or 8 Gbps.
v Up to six 1 GbE ports supporting the FCIP and Fibre Channel Routing Services
features with transmit link speeds up to 1-Gbps on each port.

© Copyright IBM Corp. 2009, 2013 1


Note: Two ports (ge0 and ge1) can be configured for use with either copper or
optical cables.
v Rack mountable 1U chassis.
v One 10/100/1000 Base-T Ethernet port for management interface.
v One RJ45 terminal port.
v Two redundant, hot-swappable combined power supply/fan assembly FRUs.
v Five internal temperature sensors.

SAN06B-R features
Table 3 compares features supported on the base and fully upgraded SAN06B-R. It
also shows optionally licensed features.
Table 3. Feature comparison - base model and with the upgrade license
Feature Base model With upgrade license
Number of Fibre Channel 4 16
ports
Number of GbE ports 2 6
1
Fibre Channel routing Yes Yes1
between remote fabrics for
fault isolation
FCIP Tunnel Yes Yes
Number of FCIP tunnels 2 8
2
FCIP Trunking Yes Yes2
Adaptive Rate Limiting Yes2 Yes2
FC frame compression Yes Yes
Storage optimized TCP Yes Yes
Fast Write over FCIP tunnel Yes Yes
Open Systems Tape No Yes
Pipelining over FCIP tunnel
FICON CUP No Yes3
1
Requires IR license
2
Requires Advanced Extension license
3
Requires FICON CUP license

v Before the installation of the upgrade license, ports beyond the basic four FC
and two GbE are shown as Disabled with the switchShow command.
v On the base SAN06B-R model, the two GbE ports (ge0 and ge1) can be
configured for use with either copper or optical cables (physically separate ports
provided).
v FC frame compression is not the same as IP compression and is disabled by
default. It can be enabled using the portCfg command. For more information see
the Fabric OS Administrator’s Guide.
v FCIP tunnel bandwidth has a minimum rate of 1544 Kbps (T1 rate).
Configuration requests of lower rates will be rejected.
v FCIP Trunking is available which will “virtualize” two or more TCP connections
(circuits) as part of a single FCIP tunnel. Up to four circuits can be configured
for a single FCIP tunnel. See the Fabric OS Administrator’s Guide for details on
explicitly configuring circuits.

2 SAN06B-R Installation, Service, and User Guide


v Multiple FCIP tunnels can share the same GbE port. At the same time, VE_ and
VEx_Ports are not associated with a single physical GbE port.

Available licenses
The following features are available with the purchase of a specific license key for
the SAN06B-R.
v Advanced Extension–enables two advanced extension features, FCIP Trunking
and Adaptive Rate Limiting (ARL).
v Integrated Routing (IR)–allows any port in a SAN768B, SAN384B, SAN80B-4,
SAN40B-4, and SAN06B-R to be configured as an (EX_port) supporting Fibre
Channel Routing (FCR)
v FICON Accelerator–designed to support secure data movement across the
enterprise data centers
v FICON CUP–designed to provide in-band management of the supported SAN
b-type switch, router, and director products by System Automation for z/OS
from IBM System zSeries servers
v Extended Fabric–extends SAN fabrics beyond the FC standard 10 km by
increasing the internal switch buffers to help maintain performance on ISLs at
distances
v Adapative Networking–provides a set of capabilities allowing high-priority
connections to obtain the bandwidth necessary for optimum performance
v ISL Trunking–provides the ability to aggregate multiple physical links into one
logical link.
v Fabric Watch–enables real-time proactive awareness of the health, performance,
and security of each switch.
v Advanced Performance Monitoring–enables performance monitoring of
networked storage resources.
v Server Application Optimization (SAO)–designed to bring Quality of Service
(QoS) enhancements for server consolidation and virtualization (requires a
minimum FOS version 6.4.

For more information on these features, see the Fabric OS Administrator’s Guide.

Port side of the switch


Figure 1 shows the port side of the switch.

2 3 4 5 6 7 8
r06b001

1 9

Figure 1. Port side view

1 System Power LED 6 Fibre Channel Ports (16)


2 System Status LED 7 GbE ports - copper RJ45(2)
3 Console Port (RJ45) 8 GbE ports - optical SFP (6)

Chapter 1. Introducing the SAN06B-R 3


4 Ethernet Management 9 Serial number pull-out tab
Port
5 USB Port

The Fibre Channel ports are numbered from left to right on the faceplate (see
Figure 2).

1 3

r06b002
2 4

Figure 2. Port numbering

1 Fibre Channel Ports 0 3 GbE ports ge0-ge1 (copper only)
through 3
2 Fibre Channel Ports 4 4 GbE ports ge0 through ge5 (SFP)
through 15

Nonport side of the switch


Figure 3 shows the nonport side of the switch, which contain the combined power
supplies and fans.

11 1 12 2

r06b003

3 4 5 6 7 8 9 10

Figure 3. Nonport side of the switch

1 Fan and power 7 Fan assembly 1


supply assembly 2
2 Fan and power 8 FRU LED
supply assembly 1
3 Fan assembly 2 9 Power supply 1
4 FRU LED 10 Fan assembly 1
5 Power supply 2 11 FRU handle
6 Fan assembly 2 12 FRU handle

4 SAN06B-R Installation, Service, and User Guide


SAN06B-R management
You can use the management functions built into the switch to monitor the fabric
topology, port status, physical status, and other information to help you analyze
switch performance and to accelerate system debugging.

Note: The switch automatically performs a power-on self-test (POST) each time it
is turned on. Any errors are recorded in the error log. For more information
about POST, see “Interpreting POST results” on page 30.

For information about upgrading the version of Fabric OS installed on your switch,
see the Fabric OS Administrator’s Guide.

You can manage the switch using any of the management options listed in Table 4.
Table 4. Management options
Management Tool Out-of-band Support In-band Support
Command line interface Ethernet (preferred) or IP over Fibre Channel
(CLI) console port connection

Up to two admin sessions


and four user sessions
simultaneously. For more
information, see the Fabric
OS Administrator’s Guide and
the Fabric OS Command
Reference.
Data Center Fabric Manager Ethernet (preferred) or IP over Fibre Channel
(DCFM) console port connection

For information, see the Data


Center Fabric Manager User
Manual.
Web Tools Ethernet (preferred) or IP over Fibre Channel
console port connection
For information, see the Web
Tools Administrator’s Guide.
Standard SNMP applications Ethernet (preferred) or IP over Fibre Channel
console port connection
For information, see the
Fabric OS MIB Reference.
Management Server Ethernet (preferred) or Native in-band interface
console port connection (over HBA only)
For information, see the
Fabric OS Administrator’s
Guide and the Fabric OS
Command Reference.

Chapter 1. Introducing the SAN06B-R 5


6 SAN06B-R Installation, Service, and User Guide
Chapter 2. Installing and configuring the SAN06B-R
You can install the SAN06B-R in the following ways:
v As a stand-alone unit on a flat surface. For instructions and more information,
see “Setting up the switch as a standalone unit” on page 8.
v In an Electronic Industries Association (EIA) cabinet using the fixed rack mount
kit, slide rack mount kit, or the mid-mount rack kit. For more information, see
“Installing in an EIA cabinet” on page 9.

To install and operate the switch successfully, ensure that the following
requirements are met:
v The primary AC input is 100-240 VAC (switch autosenses input voltage), 47-63
Hz. 200-240 VAC is recommended.
v The primary outlet is correctly wired, protected by a circuit breaker, and
grounded in accordance with local electrical codes.
v The supply circuit, line fusing, and wire size are adequate, as specified by the
electrical rating on the switch nameplate.

For power supply information, see “Power supply” on page 38.

To ensure adequate cooling, install the switch with the nonport side, which
contains the air intake vents, facing a cool-air aisle.

Verify that the ambient air temperature does not exceed 40° C (104° F) and that the
ambient humidity remains between 20% and 85% while the switch is operating.

This chapter provides the following information:


v “Items included with the switch”
v “Installation and safety considerations” on page 8
v “Setting up the switch as a standalone unit” on page 8
v “Installing in an EIA cabinet” on page 9
v “Cabling and setting up the switch” on page 14
v “Managing license keys (optional)” on page 23

Items included with the switch


The following items are included with the standard shipment of the switch. When
you open the packaging, verify that these items are included in the package and
that no damage occurred during shipping.

Note: If any items are damaged or missing, within the United States and Canada,
contact the IBM Quality Hotline toll-free 1-800-442-6773 or direct dial in
other locations: 770-858-8459.
v The SAN06B-R switch, containing two combined power supply/fan assembly
FRUs
v The following rack mount kits are optionally available:
– Fixed rack mount kit, with installation instructions
– Slide rack mount kit, with installation instructions
– Mid-mount kit, with installation instructions

© Copyright IBM Corp. 2009, 2013 7


v An accessory kit that contains the following items:
– SAN06B-R Quick Start Guide
– SAN06B-R Installation, Service, and User Guide (this document).
– IBM documentation CD
– Four rubber mounting feet, required for setting up the product as a
stand-alone unit
– Two grounded 6 ft. (1.8 m.) country-specific power cables
– One RJ-45 serial cable with an RJ-45 to DB9 adaptor
– Paperpack of optional features license and key activation information (if
ordered)
Attention: Retain this paperpack in a safe place. The transaction keys in
the paperpack are required for activation of optional features on the switch.
Once a feature is activated, its activation key is associated with a specific
product WWN and serial number.

Installation and safety considerations


Use this section to prepare your site for a safe and successful installation.

Attention: Read the “Safety and environmental notices” on page xiii


before attempting any installation, maintenance, or service procedures.

Ensure that two dedicated electrical branch circuits with the following
characteristics are available:
v Primary ac input 100-240 V ac, 2.0A, 47 to 63 Hz (the switch autosenses input
voltage)
v Correctly wired primary outlets, with circuit protected by a circuit breaker and
grounded in accordance with local electrical codes
v Adequate supply circuit, line fusing, and wire size, as specified by the electrical
rating on the chassis nameplate
v Located close to the product, and easily accessible

Note: To maximize fault tolerance, connect each power cord to a separate power
source.

For power supply information, see “Power supply” on page 38.

To ensure adequate cooling, install the switch with the nonport side, which
contains the air intake vents, facing a cool-air aisle.

Verify that the ambient air temperature does not exceed 40° C (104° F) and that the
ambient humidity remains between 20% and 85% while the switch is operating.

Setting up the switch as a standalone unit


To install the switch as a standalone unit, use the following procedure:
1. Unpack the switch and verify that all items listed in “Items included with the
switch” on page 7 are present and undamaged.

8 SAN06B-R Installation, Service, and User Guide


2. Clean the four corner depressions on the bottom of the switch enclosure, place
an adhesive rubber foot in each one, and firmly press into place. The rubber
feet on the switch help prevent the switch from sliding off the supporting
surface.
3. Place the switch on a flat, sturdy surface.
4. Provide power to the switch as described in “Providing power to the switch”
on page 16.

Attention: Do not connect the switch to the network until the IP address is
correctly set. For instructions on how to cable and configure the switch, and how
to set the IP address, see “Cabling and setting up the switch” on page 14.

Installing in an EIA cabinet


Attention: Refer to “Rack safety” on page xix for danger and caution notices
related to rack and cabinet installations.

You can install the rack mount kit in only one way in a cabinet, with the port side
of the switch able to slide out of the exhaust-air side of the cabinet. In this
installation, the port side of the switch is flush with the edge of the cabinet.

Time required
Approximately 30 minutes, not including configuration.

Items required
You need the following items to install the switch in a slide-rail rack:
v Straight slot screwdriver
v Rack space: 1U of rack space
v Two power cables that are provided with the switch
v Two power outlets
v Rack mount kit

Attention: Use the exact screws specified in the procedure for use with the switch
chassis. Using screws longer than 3/16 in. can damage the switch. The different
types of screws are listed in Table 5 on page 10. Make sure that you tighten all
screws used in this procedure.

Installation instructions
To install the switch in a slide-rail rack that meets EIA standards, use the following
procedure.

Note: These procedures use parts that are included in the rack-mount kit. These
parts are listed in Table 5 on page 10. The installation procedure
cross-references the items in this table. Be sure to use the referenced parts
when you perform each step.

Before you start the rack-mount installation process, locate the rack-mount slides
and the mounting bracket that are provided in the shipping container.

Figure 4 on page 10 shows the rack assembly. The number keys, such as 1, refer
to the items listed in Table 5 on page 10.

Chapter 2. Installing and configuring the SAN06B-R 9


4
4X

9
Outer Slide 8X 7
4X
EIA Rack Rail

Inner Slide
See
1 Detail A
2X

5
4X
7 10
4X 8X 11
3 6 8X
5X 12
Front of Switch 8X
6
2X
Detail A
7 2
2X
SJ000153

Figure 4. Rack assembly

1. Unpack the rack-mount kit and verify that all ordered items and parts are
present and undamaged. See Table 5 for a list of parts and the quantities
supplied.
Table 5. Parts supplied with the rack-mount kit
Item Description Quantity
1 Rack mount slide (inner and outer slide) 2
2 Right rack mount bracket (optional bracket 1
for front of switch)
3 Left rack mount bracket (optional bracket for 1
front of switch)
4 Rack mounting bracket (3-hole) 4
5 Nut clip, M5 11
6 Screw, 8-32 x 3/16 in., zinc 11
7 Screw, M5 x 12 11
8 Bracket to slide rack kit (contains items 9 - 1
12)
9 Screw, 8-32 x 3/8 in., zinc 8
10 Washer, flat, No. 8 8
11 Washer, lock, No. 8 8
12 Nut, hex, 8-32 8

10 SAN06B-R Installation, Service, and User Guide


2. Separate the inner and outer slides.
a. Open one of the slides until the lock engages.
b. Press the lock release lever (1 in Figure 5) and remove the inner rail from
the outer rail.

SJ000046

Figure 5. Separating the inner and outer rails.

c. Repeat step 2a and step 2b for the other rail.

Note: For racks with flush-mount doors, such as the 9306 Netfinity® racks, do
not install the ears. Instead, use the rack-mount slides by attaching the
switch to the set of mounting holes, which are offset 3 inches into the
rack.
3. Install the inner (smaller) slide on the switch chassis, as Figure 4 on page 10
shows.
Attention: If you use screws longer than 3/16 in. you can damage the
switch.
a. Position the flat side of the inner rail along one side of the switch. Align the
holes in the rail with the threaded holes in the side of the switch chassis.
The chamfered end of the inner rail should face toward the rear of the
switch (away from the ports) as shown in Figure 6 on page 12.
b. Attach the inner rail by using three of the 8-32 x 3/16 in. zinc screws (6 in
Table 5 on page 10).

Chapter 2. Installing and configuring the SAN06B-R 11


1

Front SJ000047

Figure 6. Mounting the moving portion of the slide and mounting brackets to the switch

c. Repeat step 3a on page 11 and step 3b on page 11 for the second inner rail
on the other side of the switch chassis.
4. Optional step: Install the right rack mount bracket 2 (see Figure 4 on page 10)
and the left rack mount bracket 3 on the switch chassis. Use these brackets to
secure the switch to the rack as shown in Figure 6.
Attention: Do not use screws longer than 3/16 in.; they can damage the
switch.
a. Position the left rack mount bracket at the left front corner of the switch
chassis. Align the two holes in the bracket with the two threaded holes in
the switch chassis.
b. Attach the bracket by using two of the 8-32 x 3/16 in. zinc screws (see 6
in Figure 4 on page 10)
c. Repeat step 4a and step 4b for the right rack mount bracket on the right
front corner of the switch chassis.
5. Attach all four of the 3-hole rack mounting brackets 4 in Figure 7 on page 13.
a. Position a 3-hole rack mounting bracket 4 at the end of one of the outer
slides.
b. Attach the bracket by using the 8-32 x 3/8 in. zinc screws 9. Ensure that
the screw heads are inside the slides.
c. Place one each of the following items on the outer end of the screw in the
order listed (see Detail A in Figure 4 on page 10):
1) Washer, flat No. 8 10
2) Washer, lock No. 8 11
3) Nut, hex, 8-32 12
d. Repeat steps 5a through 5c for the three remaining rail ends.

12 SAN06B-R Installation, Service, and User Guide


4

12 11
10 1
5

3
SJ000048

Figure 7. Mounting the fixed portion of the rail and the locking brackets to the rack

6. Install the outer (larger) slides in the rack, as shown in Figure 7.


a. At the selected height, install the five M5 nut clips 5. Put three M5 nut
clips in the front of the rack and two in the back. The middle clip in the
front of the rack is for the locking ears.

Note: Some rack mount kits might use 10-32 nut clips in place of the M5
nut clips for the locking ears.
b. Attach the slides by using four M5 x 12 screws 7 (see Figure 4 on page
10).
c. Repeat step 6a and step 6b for the other rail.
7. Install the switch in the rack.
a. Position the switch in front of the rack. Insert the switch into the rack by
sliding the inner slides that are mounted on the switch into the outer slides
that are mounted on the rack. See Figure 8 on page 14.

Chapter 2. Installing and configuring the SAN06B-R 13


SJ000049

Figure 8. Inserting slides into the rack rails

b. Check the alignment of the slides by sliding the switch in and out of the
rack. Any difficulty moving the switch indicates lateral stress or
misalignment. If this situation occurs, adjust the slide positions until the
movement is smooth.
8. Optional step: If the right and left rack mount brackets are installed on the
front corners of the switch, attach both brackets to the cabinet rack by using M5
x 12 screws 7. See step 4 on page 12 and Figure 4 on page 10. The screws
should pass through the front of each bracket and the slide rail.

Note: Some rack mount kits might use 10-32 nut clips in place of the M5 nut
clips for the locking ears.
9. Continue with initial setup of the switch by following the procedures in
“Cabling and setting up the switch.”
Attention: Do not connect the switch to the network until you perform one of
the following steps:
v Set the internet protocol (IP) address.
v Verify that the default IP address does not conflict with the existing IP
addresses in the same network.

Cabling and setting up the switch


You must configure the switch before it can operate within a network and fabric.
This section provides the basic steps required for the initial setup of the switch. For
instructions on configuring the switch to operate in a network containing switches
from other vendors, refer to the Fabric OS Administrator's Guide.

If you are going to use the switch in a single-switch setup, you can use
EZSwitchSetup to complete the basic configuration. See the EZSwitchSetup CD,
included with the switch, for more information. If you do not want to use
EZSwitch Setup, follow the instructions in the rest of this section.

For more information about the commands used in these procedures, refer to the
Fabric OS Command Reference.

14 SAN06B-R Installation, Service, and User Guide


Planning for cable management
Attention: The minimum bend radius for Cat5 and Cat6 copper cables and 50
micron cable is 51 mm (2 in.) under full tensile load and 30.5 mm (1.2 in.) with no
tensile load. Because they can be easily overtightened, tie wraps are not
recommended for use with optical cables.

Cables can be organized and managed in a variety of ways: for example, using
cable channels on the sides of the cabinet or patch panels to minimize cable
management. A list of best practices follows:
v Plan for rack space required for cable management before installing the switch.
v Leave at least 1 meter (3.28 ft) of slack for each port cable. This provides room
to remove and replace the switch, allows for inadvertent movement of the rack,
and helps prevent the cables from being bent to less than the minimum bend
radius.
v For easier maintenance, label the fiber optic cables and record the devices to
which they are connected.
v Keep LEDs visible by routing port cables and other cables away from the LEDs.
v Do not use tie wraps on fiber optic cables, because wraps can be easily
overtightened and can damage the optic fibers.

Items required for setup


The following items are required for configuring and connecting the switch for use
in a network and fabric:
v The switch, installed and connected to a power source
v Workstation with an installed terminal emulator, such as HyperTerminal
v Available IP address and corresponding subnet mask and gateway address
v Serial cable (provided)
v Ethernet cable
v SFP transceivers and compatible fiber and copper cables, as required
v Access to an FTP server for backing up or downloading the switch configuration

Setting up the switch


Follow the steps described in the next sections to set up your switch.
v “Providing power to the switch” on page 16
v “Creating a serial connection” on page 16
v “Setting the switch IP address” on page 17
v “Creating an Ethernet connection and logging in” on page 18
v “Changing the switch name and chassis name” on page 18
v “Connecting cables” on page 21
v “Setting the switch date and time” on page 19
v “Setting the switch domain ID” on page 18
v “Configuring FCIP and Fibre Channel routing services” on page 20
v “Installing SFPs” on page 21
v “Connecting cables” on page 21
v “Verifying correct operation of the switch” on page 22
v “Backing up the configuration” on page 23

Chapter 2. Installing and configuring the SAN06B-R 15


Attention: Do not connect the switch to the network until the IP address is
correctly set.

Providing power to the switch


DANGER
An electrical outlet that is not correctly wired could place
hazardous voltage on metal parts of the system or the devices that
attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent
an electrical shock. (D004)

Follow these steps to provide power to the switch.


1. Connect the power cords to the receptacles on the two power supplies on the
back of the switch.
Attention: Ensure that the power cables are routed so that they are not
pinched or exposed to stress when the switch is moved on the slide-rails.
Ensure that the cords have a minimum service loop of 15 cm (6 in.) available at
the connection to the switch.
2. Connect the other end of the power cords to the two power sources.
Attention: To protect against AC failure, connect the power cords to outlets
on separate circuits.
3. Press the "|” area of the power switch. The power supply LEDs display amber,
and the switch begins running the power on self-test (POST). The switch
requires one to three minutes to boot and complete the POST process. The LED
will then change to green.

Note: Power is supplied to the switch as soon as the first power supply is
connected and turned on.
4. After POST is complete, verify that the System Status and Power Status LEDs
display steady green (see Figure 1 on page 3).
For more information about the LEDs and their status during POST, refer to
“LED activity” on page 25.

Creating a serial connection


All basic configuration tasks in this guide are performed using a serial connection.
To create a serial connection to the switch, complete the following steps:
1. Remove the plug from the serial port and insert the serial cable provided with
the switch.
2. Connect the serial cable to the console port on the switch and to an RS-232
serial port on the workstation.
If the serial port on the workstation is RJ-45 instead of RS-232, remove the
adapter on the end of the serial cable and insert the exposed RJ-45 connector
into the RJ-45 serial port on the workstation.
3. Disable any serial communication programs running on the workstation.
4. Open a terminal emulator application (such as HyperTerminal on a PC, or
TERM, TIP, or Kermit in a UNIX environment), and configure the application
as follows:
v In a Windows environment:
Bits per second 9600

16 SAN06B-R Installation, Service, and User Guide


Databits 8
Parity None
Stop bits 1
Flow control None
v In a UNIX environment, enter the following string at the prompt:
tip /dev/ttyb -9600

If ttyb is already in use, use ttya instead and enter the following string at the
prompt:
tip /dev/ttya -9600

Connecting to the switch using the serial connection


Perform the following steps to log in to the switch through the serial connection.
1. Verify that the switch has completed POST. When POST is complete, the port
status and power and status LEDs return to a standard healthy state; for
information about LED patterns, see “LED activity” on page 25.
2. When the terminal emulator application stops reporting information, press
Enter to display the login prompt.
3. Log in to the switch as admin, using the default password: password. You will
be prompted to change the default passwords at initial login.

Setting the switch IP address


You can configure the switch with a static IP address, or you can use a DHCP
(Dynamic Host Configuration Protocol) server to set the IP address of the switch.
DHCP is enabled by default. The switch supports both IPv4 and IPv6.

Using DHCP to set the IP address: When using DHCP, the switch obtains its IP
address, subnet mask, and default gateway address from the DHCP server. The
DHCP client can only connect to a DHCP server that is on the same subnet as the
switch. If your DHCP server is not on the same subnet as the switch, use a static
IP address.

Setting a static IP address:


1. Log into the switch using the default password, which is password.
2. Use the ipaddrset command to set the Ethernet IP address.
v To use an IPv4 IP address, enter the IP address in dotted decimal notation as
prompted.
Ethernet IP Address: [192.168.74.102]
v To use an IPv6 address, enter the network information in colon-separated
notation as prompted.
switch:admin> ipaddrset -ipv6 --add 1080::8:800:200C:417A/64
IP address is being changed...Done.
3. Complete the rest of the network information as prompted (IPv4 format
shown).
Ethernet Subnetmask: [255.255.255.0]
Ethernet IP Address: [192.168.74.102]
Ethernet Subnetmask: [255.255.255.0]
4. Enter off to Disable DHCP when prompted.
DHCP [OFF]: off

Chapter 2. Installing and configuring the SAN06B-R 17


Changing the switch name and chassis name
Changing the switch and chassis names are important for accurate tracking of
errors in the RASlog. The messages that appear in the log will be labelled with the
switch or chassis name, which makes tracking the errors much easier. Choose an
easily understandable and meaningful name for each.

Perform the following steps to change the chassis name and then the switch name.
1. Log on to the switch through Telnet, using the admin account.
2. Change the chassis name by using the chassisName command.
switch:admin> chassisname my7800chassis
switch:admin> chassisname
my7800chassis
3. Change the switch name by using the switchName command.
switch:admin> switchname my7800switch
switch:admin> switchname
my7800switch

Creating an Ethernet connection and logging in


Create an Ethernet connection to the switch by completing the following steps:
1. Remove the plug from the Ethernet port (see Figure 1 on page 3).
2. Insert one end of an Ethernet cable into the Ethernet port.
3. Connect the other end to the workstation (or to an Ethernet network containing
the workstation).

Note: The switch can now be accessed remotely using command line or Web
Tools. Ensure that the switch is not being modified from any other
connections during the configuration process.

Setting the switch domain ID


Perform the following steps to set the switch domain ID.
1. Log on to the switch through Telnet, using the admin account.
2. Modify the domain ID if required.
The default domain ID is 1. If the switch is not powered on until after it is
connected to the fabric and the default domain ID is already in use, the domain
ID for the new switch is automatically reset to a unique value. If the switch is
connected to the fabric after it has been powered on and the default domain ID
is already in use, the fabric will segment. To find the domain IDs that are
currently in use, run the fabricShow command on another extension switch in
the fabric.
a. Disable the switch by entering the switchDisable command.
b. Enter the configure command. The command prompts will display
sequentially; enter a new value or press Enter to accept each default value.
c. Enter y after the "Fabric param" prompt:
Fabric param (yes, y, no, n): [no] y
d. Enter a unique domain ID (such as the domain ID used by the previous
extension switch, if still available):
Domain: (1..239) [1] 3
e. Complete the remaining prompts or press Ctrl+D to accept the remaining
settings without completing all the prompts.
f. Re-enable the switch by entering the switchEnable command.

18 SAN06B-R Installation, Service, and User Guide


Setting the switch date and time
The date and time switch settings are used for logging events. Switch operation
does not depend on the date and time; a switch with incorrect date or time values
still functions properly. You can synchronize the local time of the principal or
primary fabric configuration server (FCS) switch to that of an external Network
Time Protocol (NTP) server.

Perform the following steps to set the date and time of the switch.

Setting the date and time


1. Log in to the switch as admin.
2. Enter the date command, using the following syntax:

date "MMDDhhmm[CC]YY"

The values represent the following:


v MM is the month (01-12)
v DD is the date (01-31)
v hh is the hour (00-23)
v mm is minutes (00-59)
v CC is the century (19-20)
v YY is the year (00-99)
Year values greater than 69 are interpreted as 1970-1999; year values less than
70 are interpreted as 2000-2069. The date function does not support Daylight
Savings Time or time zones, so changes will have to be reset manually.

switch:admin> date
Fri Sep 29 17:01:48 UTC 2007
switch:admin> date "0927123007"
Thu Sep 27 12:30:00 UTC 2007
switch:admin>

Synchronizing local time with an external source


Perform the following steps to synchronize the local time of the principal or
primary FCS switch with that of an external NTP server.
1. Log in as admin.
2. Enter the tsClockServer ipaddr command.

The ipaddr variable represents the IP address of the NTP server that the switch can
access. This argument is optional; by default the value is LOCL.
sw7800:admin> tsclockserver 192.168.126.60
Updating Clock Server configuration...done.
Updated with the NTP servers
sw7800:admin>

Correcting the time zone of the switch


If the time of your switch is off by hours (and not minutes), use the following
procedure to set the time zone. This needs to be done only once, because the value
is stored in nonvolatile memory.
1. Log in as admin.
2. You can use the tstimezone -interactive command and follow the prompts or
enter the tsTimeZone command as follows:
tstimezone [houroffset [, minuteoffset]]

Chapter 2. Installing and configuring the SAN06B-R 19


The values of houroffset and minuteoffset are determined by your time zone. The
default time zone for switches is universal time conversion (UTC). For U.S. time
zones, use Table 6 to determine the correct values.

Note: The values in Table 6 do not apply if the time zone of the switches has
already been changed from the default.
Table 6. tsTimeZone command parameter values
Time zone houroffset minuteoffset
Atlantic Standard -4 0
Atlantic Daylight -3 0
Eastern Standard -5 0
Eastern Daylight -4 0
Central Standard -6 0
Central Daylight -5 0
Mountain Standard -7 0
Mountain Daylight -6 0
Pacific Standard -8 0
Pacific Daylight -7 0
Alaskan Standard -9 0
Alaskan Daylight -8 0
Hawaiian Standard -10 0

For more detailed information about the parameters of the tsTimeZone command,
refer to the Fabric OS Command Reference.

Configuring FCIP and Fibre Channel routing services


The ports on the switch are initially set to persistently disabled. Once the switch is
powered on, the port LEDs will flash amber until they are enabled. This is normal.
If you want to enable the FC ports as a standard E_Port or F_port, use the
portCfgPersistentEnable command to enable the ports. If you are using the FC
ports as EX_Ports you must configure the Fibre Channel Routing Services feature
prior to enabling the ports. The GbE ports can only be used after you have
configured FCIP and enabled the VE_Ports. See the “Using the FC-FC Routing
Service” and “Using the FCIP Tunneling Service” chapters of the Fabric OS
Administrator’s Guide for detailed instructions on configuring the Fibre Channel
Router ports and GbE ports on the switch.

20 SAN06B-R Installation, Service, and User Guide


Installing SFPs
| Attention: With increasing speeds of optical connections, the cleanliness of the
| connections assumes greater importance in ensuring maximum performance and
| error free transmission. Due to the tighter tolerances associated with state of the art
| optics, levels of contamination that were acceptable at lower speeds may not be at
| higher speeds. While IEC Standard 61300-3-35 specifies a set of guidelines for
| trouble free performance, most issues can be avoided by adhering to the following
| best practices:
| v When cables or connectors are not in use for extended periods of time, use the
| dust covers provided.
| v Ensure that the cable length and type that is used are suitable for the speed and
| application.
| v Inspect and clean optical connections and fiber cables before you connect or
| reconnect components.
| v Ensure that cables are properly seated within the connector.
| Kits are commercially available for cleaning and inspecting these connections. IBM
| also offers services that will ensure optimal condition of the network.

Perform the following steps to install SFPs and cable the switch.
1. Install the SFP transceivers in the Fibre Channel ports, as required. The ports
selected for use in trunking groups must meet specific requirements. For a list
of these requirements, see the Fabric OS Administrator’s Guide.
a. Remove the plugs from the ports to be used.
| b. Ensure that both cable and transceiver are clean prior to installation.
c. Position a transceiver so that it is oriented correctly and insert it into a port
until it is firmly seated and the latching mechanism clicks. For instructions
specific to the type of transceiver, see the transceiver manufacturer’s
documentation.

Note: The transceivers are keyed to ensure correct orientation. If a


transceiver does not install easily, ensure that it is correctly oriented.
d. Repeat steps 1a through1c for the remaining ports, as required.
2. If you have chosen to use the optical ports for ge0 and ge1, install those SFPs.
If you have licensed the additional GbE ports, install the SFP transceivers in
GbE ports ge2 through ge5.
a. Remove the plugs from the ports to be used.
| b. Ensure that both cable and transceiver are clean prior to installation.
c. Position a transceiver so that it is oriented correctly and insert it into a port
until it is firmly seated and the latching mechanism clicks. Be sure that you
are using Brocade-branded 4 Gbps SFPs in the GbE ports.
d. Use the portcfggemediatype command to configure ge0 and ge1 to either
copper or optical. For instance, to select the optical option for port ge0, use
the following command.
switch:admin> portcfggemediatype ge0 optical

Connecting cables
Attention: A 50-micron cable should not be bent to a radius less than 5 cm (2 in.)
under full tensile load and 3 cm (1.2 in.) with no tensile load. Tie wraps are not
recommended for optical cables because they can be easily overtightened.

Chapter 2. Installing and configuring the SAN06B-R 21


1. Orient a cable connector so that the key (the ridge on one side of connector)
aligns with the slot in the transceiver. Then, insert the cable into the transceiver
until the latching mechanism clicks. For instructions specific to cable type, see
the cable manufacturer's documentation.

Note: The cable connectors are keyed to ensure correct orientation. If a cable
does not install easily, ensure that it is correctly oriented.
2. Repeat for the remaining cables as required.
3. If you have chosen the copper option for GbE ports ge0 and ge1, install those
cables now.
4. Check the LEDs to verify that all components are functional. For information
about LED patterns, see “LED activity” on page 25.
5. Verify the correct operation of the switch by entering the switchShow
command from the workstation.

Verifying correct operation of the switch


To verify the correct operation of the switch, complete these steps:
1. Check the LEDs to verify that all components are functional. For information
about LED patterns, refer to “LED activity” on page 25.
2. Run the portCfgPersistntEnable command to activate the FC ports for FC
operation.
3. Verify the correct operation of the switch by entering the switchShow
command from the workstation. This command provides information about the
switch and its port status, such as in the example below.
sw7800:admin> switchshow
switchName: sw7800
switchType: 83.3
switchState: Online
switchMode: Native
switchRole: Principal
switchDomain: 220
switchId: fffcdc
switchWwn: 10:00:00:05:1e:55:a2:00
zoning: ON (DEFAULT_CFG_LSAN)
switchBeacon: OFF
FC Router: ON
FC Router BB Fabric ID: 1
Index Port Address Media Speed State Proto
==============================================
0 0 dc0000 id N8 No_Light FC
1 1 dc0100 id N8 No_Light FC
2 2 dc0200 id N8 No_Light FC
3 3 dc0300 id N8 No_Light FC
4 4 dc0400 -- N8 No_Module FC
5 5 dc0500 -- N8 No_Module FC
6 6 dc0600 -- N8 No_Module FC
7 7 dc0700 -- N8 No_Module FC
8 8 dc0800 id N8 No_Light FC
9 9 dc0900 -- N8 No_Module FC
10 10 dc0a00 id N8 No_Light FC
11 11 dc0b00 id N8 No_Light FC
12 12 dc0c00 id N8 No_Light FC
13 13 dc0d00 id N8 No_Light FC
14 14 dc0e00 id N8 No_Light FC
15 15 dc0f00 id N8 No_Light FC
16 16 dc1000 -- -- Offline VE
17 17 dc1100 -- -- Offline VE
18 18 dc1200 -- -- Offline VE
19 19 dc1300 -- -- Offline VE

22 SAN06B-R Installation, Service, and User Guide


20 20 dc1400 -- -- Offline VE
21 21 dc1500 -- -- Offline VE
22 22 dc1600 -- -- Offline VE
23 23 dc1700 -- -- Offline VE
ge0 id 1G No_Light FCIP
ge1 id 1G No_Light FCIP
ge2 id 1G No_Light FCIP
ge3 id 1G No_Light FCIP
ge4 id 1G No_Light FCIP
ge5 id 1G No_Light FCIP
sw7800:admin>
4. Verify the correct operation of the switch in the fabric by entering the
fabricShow command from the workstation. This command provides general
information about the fabric.

Backing up the configuration


You should save all key configuration data for the switch (including license key
information) and upload it to a FTP server for emergency reference. Back up the
configuration on a routine basis to ensure that a complete and current
configuration is available if needed.

After configurations are complete, back up the configuration by entering the


configUpload command and following the prompts.
sw7800:admin> configupload
Protocol (scp, ftp, local) [ftp]:
Server Name or IP Address host: 192.168.0.100
User Name user: anonymous
Path/Filename [home dir/config.txt]:
Section (all|chassis|switch [all]): all
configUpload complete: All selected config parameters are uploaded
sw7800:admin>

The configUpload command uploads the switch configuration to the server so that
it is available for downloading to a replacement switch, if necessary. For specific
instructions about how to back up and restore the configuration, see the
“Maintaining Configurations” chapter in the Fabric OS Administrator's Guide. The
switchShow, fabricShow, and configUpload commands are described in detail in
the Fabric OS Command Reference.

Managing license keys (optional)


Depending on what has been ordered, certain licenses are factory-installed on the
switch. Feature licenses might be included as a paperpack item in the switch
shipping carton. This paperpack provides you with keys to unlock the features.
You can also purchase licenses separately from IBM.

Attention: Retain this paperpack in a safe place. The transaction keys in the
paperpack are required for activation of optional features on the switch. After a
feature is activated, its activation key is associated with a specific product WWN
and serial number.

Refer to the following sections for information about viewing the current licenses,
adding a license, or removing a license. For more information on the following
procedures, see the Fabric OS Administrator's Guide and the Fabric OS Command
Reference.

Chapter 2. Installing and configuring the SAN06B-R 23


Viewing current license keys
To view the licenses that are currently enabled on the switch, complete the
following steps.
1. Log in as admin.
2. Enter the licenseShow command. A list of the enabled licenses and their
features is displayed, as in the following example.
APswitch:admin> licenseshow
License Key: bQebzeRdScRfc0iK
Web license
License Key: SybbzQQ9edTzcd0X
Zoning license
APswitch:admin>

Adding a license key


Licenses for additional functionality may be purchased as feature codes through
IBM. Contact your IBM representative for more information. You will need to
supply IBM with the WWN to obtain a transaction key, which is sent in a
paperpack. To obtain the license key, follow the instructions included in the
paperpack. The transaction key and the switch WWN or product serial number are
required to obtain the license key.

To add a license to the switch, complete the following steps.


1. Log in as admin.
2. Enter the switchShow command to obtain the WWN of your switch. The
license key is a string of approximately 16 uppercase and lowercase letters and
digits. Case is significant. The key is an encrypted form of the system WWN
and the products licensed to run on this system.
3. Enter the licenseAdd command, followed by the license key enclosed in
quotation marks, as shown in the following example.
APswitch:admin> licenseadd "aBcDeFGh12345K"
License key aBcDeFGh12345 added

Enter the license key into the system exactly as issued. If you enter it
incorrectly, the license might be accepted, but it will not function.
4. After entering the license key, use the licenseShow command to verify that it is
valid. If a licensed product is not displayed, the license is invalid.

Note: After you enter a license, the licensed product is available immediately;
the system does not need to be rebooted.

Removing a license key


To remove a license from the switch, complete the following steps.
1. Log in as admin.
2. Enter the licenseRemove command, followed by the license key enclosed in
quotation marks, as in the following example.
APswitch:admin> licenseremove "bQebzbRdScRfc0iK"
removing license key "bQebzbRdScRfc0iK"
3. Save the license key information in case you want to reinstall it in the future.
4. After removing the license key, the switch must be rebooted.
5. Use the licenseShow command to verify that the license key has been
removed.

24 SAN06B-R Installation, Service, and User Guide


Chapter 3. Operating the SAN06B-R
The switch is engineered for reliability and requires no routine operational
maintenance. However, this chapter provides information about determining the
overall status of the system and each of its components using LEDs and CLI
commands.

This chapter provides the following information:


v “LED activity”
v “Interpreting POST results” on page 30
v “Diagnostics and troubleshooting” on page 31

LED activity
System activity and status can be determined through the activity of the LEDs on
the switch.

There are three possible LED states:


v No light
v Flashing
v Steady light

Active lights are either green or amber. The status LEDs might display solid amber
or flash during boot, POST, or other diagnostic tests. This is normal; it does not
indicate a problem unless the LEDs do not indicate a healthy state after all boot
processes and diagnostic tests are complete.

LEDs on the port side of the switch


The port side of the switch has the following LEDs:
v One system status LED (above) on the left side.
v One power status LED (below) on the left side.
v Management Ethernet port speed and activity LEDs.
v One port status LED for each Fibre Channel port on the switch. The port LEDs
are located in the array in the same relative positions as the ports.
v One port status LED for each optical GbE port.
v Two LEDs for each copper GbE port, one activity/status LED and one fault
LED.

Figure 9 on page 26 shows the port side of the switch.

© Copyright IBM Corp. 2009, 2013 25


1 2 3 4 6 5 7 8 9 10 11

r06b004

13 12 14 15 16

Figure 9. LEDs on port side

1System status LED 9Port 0 status LED


2System power LED 10Port 4 status LED
3Console port 11Port 8 status LED
4Ethernet link LED 12GbE copper port
5Ethernet status LED 13GbE port 0 fault (FLT) LED
6Ethernet port 14GbE port 0 status/activity LED
7IP address pull-out tab 15GbE optical port
8USB port 16GbE dual-color optical port LED

Power status LED patterns


The power status LED on the front of the switch (see 2 in Figure 9) indicates the
status of the power supplied to the switch. Table 7 on page 27 describes the
meaning of different displays of the power supply LED and recommended action,
if any.

26 SAN06B-R Installation, Service, and User Guide


Table 7. Power status LED patterns
LED color Status of hardware Recommended action
No light (off) System is off or there is an Verify that system is powered on (power supply switches to
internal power supply failure. "|"), the power cables attached, and your power source is live.
If the system power LED is not green, the unit may be faulty.
Contact your IBM representative.
Steady green System is on and power No action required.
supplies are functioning
properly

System status LED patterns


The system status LED (1 in Figure 9 on page 26) indicates the overall system
status. Table 8 describes the meaning of different displays of the system status LED
and recommended action, if any.
Table 8. System status LED patterns
LED color Status of hardware Recommended action
No light System is off or there is no Verify that the system is on and has completed booting and
power. POST.
Steady green System is on and functioning No action required.
properly
Steady amber Unknown state, boot failed, or Perform the following steps:
(for more than the system is faulty. 1. Connect a serial cable to the system.
5 seconds) Note: This LED displays steady
2. Reboot the system.
amber during POST, this is
normal and does not indicate a 3. Check the failure indicated on the system console.
fault. If the problem does not resolve, contact your IBM
representative.
Flashing Attention is required. A number Check the management interface and the error log for details on
amber/green of variables can cause this status the cause of status.
including a single power supply Contact your IBM representative.
failure, a fan failure, or one or
more environmental ranges has
been exceeded.

Ethernet management port LED patterns


The Ethernet management port has two LEDs to indicate Ethernet link (4
Figure 9 on page 26) and Ethernet status/activity (5). Table 9 describes the
meaning of different displays of the Ethernet LEDs and recommended action, if
any.
Table 9. Management port LED patterns
LED name LED color Status of hardware Recommended action
Ethernet link No light No link Verify that the Ethernet cable is
connected correctly.
Steady green Link exists No action required.
Ethernet No light No activity No action required.
status/activity
Flashing green Activity (traffic). No action required.

Chapter 3. Operating the SAN06B-R 27


Fibre Channel port status LED patterns
The switch has one LED below each Fibre Channel port (9, 10, 11in Figure 9
on page 26) to indicate how that particular port is functioning. Table 10 describes
the meaning of different displays of the port LEDs and recommended action, if
any.
Table 10. FC port status LED patterns
LED color Status of hardware Recommended action
No light Indicates one of the following: 1. Verify that power LED is on.
v No signal or light carrier (SFP or 2. Check the transceiver and cable.
cable) detected
3. Verify the switch has completed booting and
v Switch may be initializing POST.
v Connected device is configured in an 4. Verify the status of the connected device.
offline status
Steady green Port is online (connected to external No action required.
device) but has no traffic.
Slow-flashing green Port is online but segmented because of Verify that the correct device is attached to the
(on 1 second; then a loopback cable or incompatible switch switch.
off 1 second) connection.
Fast-flashing green Port is online and an internal loopback No action required.
(on 1/4 second; diagnostic test is running.
then off 1/4 second)
Flickering green Port is online and data is flowing No action required.
through the port.
Steady amber Port is receiving light or signal carrier, No action required.
but it is not online yet.
Slow-flashing Port is disabled because of diagnostics Reset the port.
amber (on 2 or the portdDisable command. Note: The portCfgPersistentDisable command is
seconds; then off 2 persistent across reboots. Use the portCfgDefault
seconds) command to return the port to its default (enabled)
status.
Fast-flashing amber SFP or port is faulty. Reset the port. Replace the SFP. If the problem does
(on 1/2 second; not resolve, contact IBM.
then off 1/2 second)

GbE optical port status LED patterns


The switch has one LED below each GbE optical port (16 in Figure 9 on page 26)
to indicate how that particular port is functioning. Table 11 describes the meaning
of different displays of the port LEDs and recommended action, if any.
Table 11. GbE optical port status LED patterns
LED color Status of hardware Recommended action
No light Port is offline v Verify that power LED is on.
v Check the transceiver and cable.
Steady green Port is online (connected to external No action required.
device) but has no traffic.
Flickering green Port is online and data is flowing No action required.
through the port.
Steady amber Port is faulty Change the transceiver or reset the switch from the
workstation.

28 SAN06B-R Installation, Service, and User Guide


GBE copper port status LED patterns
The switch has two LEDs (one green and one amber) above each GBE copper port
(13 and 14 in Figure 9 on page 26) to indicate how that particular port is
functioning. Table 12 describes the meaning of different displays of the port LEDs
and recommended action, if any.
Table 12. GBE copper port status LED patterns
LED color Status of hardware Recommended action
No lights (both Port is offline v Verify that power LED is on.
LEDs are off)
v Check the transceiver and cable.
Steady green, amber Port is online (connected to external No action required.
off device) but has no traffic.
Flickering green, Port is online and data is flowing No action required.
amber off through the port.
Green off, steady Port is faulty Reset the switch from the workstation. If the fault
amber persists, use the other copper port or the optical
ports, or contact IBM.

LEDs on the nonport side of the switch


The LEDs on the nonport side of the switch provide status information for the two
power supply/fan assemblies. Figure 10 shows the location of these LEDs and
other components on the nonport side of the switch.

11 1 12 2

r06b003
3 4 5 6 7 8 9 10

Figure 10. Nonport side components

1 Fan and power 7 Fan assembly 1


supply assembly 2
2 Fan and power 8 FRU LED
supply assembly 1
3 Fan assembly 2 9 Power supply 1
4 FRU LED 10 Fan assembly 1
5 Power supply 2 11 FRU handle
6 Fan assembly 2 12 FRU handle

Power supply/fan status LED patterns


Each power supply/fan assembly has one LED (4 and 8 in Figure 10) next to
the AC power switch. This LED indicates the status of the power supply and the
fan. Table 13 on page 30 describes the meaning of different displays of the LEDs
and recommended action, if any.

Chapter 3. Operating the SAN06B-R 29


Table 13. Power supply/fan status LED patterns
LED color Status of hardware Recommended action
No light Power supply/fan assembly is not seated Reseat power supply.
correctly.
Steady green Power supply/fan assembly is operating No action required.
normally.
Flashing green Power supply/fan assembly fault for one of 1. Check the power cable connection.
the following reasons:
2. Verify that the power supply/fan assembly is
v The power cable is disconnected powered on.
v Power supply/fan assembly is switched off 3. Run psShow and fanShow commands to
v The power supply has failed determine the source of the fault.
If the actions above do not resolve the problem,
replace the power supply/fan assembly.

Interpreting POST results


POST is a system check that is performed each time the switch is powered on,
rebooted, or reset, and during which the LEDs flash different colors.

To determine whether POST completed successfully and whether any errors were
detected:
1. Verify that the LEDs on the switch indicate that all components are healthy (see
“LED activity” on page 25). If one or more LEDs do not display a healthy state:
a. Verify that the LEDs are not set to “beacon” (this can be determined
through the switchShow command or Web Tools). For information about
how to turn beaconing on and off, see the Fabric OS Administrator's Guide or
the Web Tools Administrator's Guide.
b. Follow the recommended action for the observed LED behavior, as listed in
the tables in “LED activity” on page 25.
2. Verify that diagShow command displays that the diagnostic status for all ports
in the switch is OK.
3. Review the system log for errors. Errors detected during POST are written to
the system log, which is viewed using the errShow command. For more
information about this command, see the Fabric OS Command Reference. For
information about specific error messages, see the Fabric OS Message Reference.

30 SAN06B-R Installation, Service, and User Guide


Diagnostics and troubleshooting
The switch is designed for high availability and low failure. It does not require any
regular physical maintenance. It includes diagnostic tests and field-replaceable
units, described in the following sections.

Diagnostic tests
In addition to POST, Fabric OS includes diagnostic tests to help you troubleshoot
the hardware and firmware. This includes tests of internal connections and
circuitry, fixed media, and the transceivers and cables in use. The tests are
implemented by command, either through a Telnet session or through a terminal
set up for a serial connection to the switch. Some tests require the ports to be
connected by external cables, to allow diagnostics to verify the
serializer/deserializer interface, transceiver, and cable. Some tests require loopback
plugs.

Diagnostic tests are run at link speeds of 1 Gbps, 2 Gbps, 4 Gbps, and 8 Gbps. For
information about specific diagnostic tests, see the Fabric OS Administrator's Guide.

Note: Diagnostic tests might temporarily lock the transmit and receive speed of
the links during diagnostic testing. After completing offline diagnostics tests,
power-cycle the switch.

CRU status
The power supply/fan assemblies are customer replaceable units (CRUs), which
can be replaced without the use of special tools. To determine the status of these
CRUs, use the following diagnostic procedures. Follow the procedures in
“Replacing a power supply/fan assembly” on page 32 if you determine that any
CRUs are defective.

Power supply/fan assemblies


The two power supply/fan assemblies, #1 (1 in Figure 11 on page 32) and #2
(2), are hot-swappable. They are identical and fit into either power supply/fan
slot. They are keyed to prevent being inserted upside down.

Fabric OS identifies the power supply/fan assemblies as follows (viewing the


switch from the nonport side):
v Power supply #1 on the right
v Power supply #2 on the left

Fabric OS identifies the fan asemblies as follows (viewing the switch from the
nonport side):
v Fan assembly #1 on the right
v Fan assembly #2 on the left

The FRUs are cross-connected so that if one power supply fails, the fans will
continue to run on power from the other power supply.

Use any of the following methods to determine whether a power supply needs to
be replaced:
v Check the power supply status LED next to the On/Off switch (see “Power
status LED patterns” on page 26).
v In Web Tools, click the Power Status or Fan Status icons.

Chapter 3. Operating the SAN06B-R 31


v Enter the psShow (or fanShow) command at the command prompt to display
power supply status as shown in the example below:
sw7800:admin> psshow
Power Supply #1 is OK
V10529, TQ2H0000118 ,60-0300031-01,X2, ,SP640 ,2X,TQ2H0000
Power Supply #2 is OK
V10529, TQ2H0000121 ,60-0300031-01,X2, ,SP640 ,2X,TQ2H0000
sw7800:admin>

See “Replacing a power supply/fan assembly” for information on how to remove


and replace the CRU.

Replacing a power supply/fan assembly


This section describes how to remove and replace the power supply/fan
assemblies. Although these CRUs can be removed and replaced without special
tools, qualified personnel should perform the installation and service procedures.
The switch can continue operating during the CRU replacement if you adhere to
the conditions specified in the procedures.

Attention: Before installing, removing, or replacing any component, read and


follow the “Safety notices and labels” on page xiii.

The switch has two power supply/fan assemblies, #1 (1 in Figure 11) and #2
(2). The power supply/fan assemblies are hot-swappable as long as one of them
remains operating during the procedure. Each power supply/fan is identical and
fits into either power supply/fan slot. Refer to “Power supply/fan status LED
patterns” on page 29 to help diagnose problems with a power supply/fan. You can
also use the switchStatusShow command to verify the status of the power
supply/fan assemblies. Refer to the Fabric OS Command Reference for more
information on this command.

2 1

r06b005

4 3 4 3

Figure 11. Power supply/fan locations

1 Power supply/fan #1 3 On/Off switch


2 Power supply/fan #2 4 LED

Time required: Less than 2 minutes

Items required:
v New power supply
v Phillips screwdriver

32 SAN06B-R Installation, Service, and User Guide


DANGER
Hazardous voltage, current, or energy levels are present
inside any component that has this label attached. (L001)

Do not service, there are no serviceable parts.

Attention: Disassembling any part of the power supply/fan assembly voids the
part warranty and regulatory certifications. There are no user-serviceable parts
inside the power supply/fan assembly.
Because the cooling system relies on pressurized air, do not leave either of the
power supply/fan slots empty longer than 2 minutes while the switch is operating.
If a power supply/fan fails, leave it in the switch until it can be replaced. This will
ensure proper airflow for cooling.
Maintain both power supply/fan assemblies in operational condition to provide
redundancy.

Procedure: Complete the following steps to remove and replace a power


supply/fan assembly.
1. To leave the switch in service while you replace a power supply/fan assembly,
verify that the other power supply/fan (the one not being replaced) has been
powered on for at least four seconds and has a green LED.
2. Power off the power supply/fan being replaced by pressing the AC power
switch to “O”.
3. Unplug the power cord from the power supply/fan that you are replacing.
4. Unscrew the captive screw, using a Phillips screwdriver.
5. Remove the power supply/fan from the chassis by pulling the handle on the
power supply/fan out, away from the chassis.
6. Install the new power supply/fan in the chassis:
Attention: Do not force the installation. If the power supply/fan does not
slide in easily, ensure that it is correctly oriented before continuing.
a. Verify that the AC switch on the new power supply/fan is in the “O” (off)
position.
b. Orient the power supply/fan as shown in Figure 12, with the ac switch on
the left.
r06b006

Figure 12. Orientation of the power supply and fan assembly

c. Using the handle, gently push the power supply/fan into the chassis until it
is firmly seated.
Attention: Do not force the installation. If the FRU does not slide in easily,
ensure that it is correctly oriented before continuing.
d. Tighten the captive screw.

Chapter 3. Operating the SAN06B-R 33


7. Connect the power cord to the power supply/fan and then press the AC power
switch to “O” (on).
8. Verify that the LED on the new power supply/fan displays a steady green light
while the switch is operating. If the LED is not green, ensure that the power
supply is securely installed, the power plug is secure, and the primary power is
available.
9. Optionally, enter psShow at the command line prompt to view the power
supply status. For more information about this command, refer to the Fabric OS
Command Reference.

Powering off the switch


To power off the switch:
1. Run the sysShutDown command.

Note: This command shuts down the key processors and powers off the
switch. All LEDs go dark.
2. Set each ac power switch to “O”.

Removing the battery


CAUTION:
The battery contains lithium. To avoid possible explosion, do not burn or charge
the battery. Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble
Exchange only with the IBM-approved part. Recycle or discard the battery as
instructed by local regulations. In the United States, IBM has a process for the
collection of this battery. For information, call 1-800-426-4333. Have the IBM part
number for the battery unit available when you call. (C003)

Local regulations may require removing the battery prior to disposing of or


recycling this product. Complete these steps to remove the battery.
1. Disconnect all power and communication cables.
2. Remove all transceivers.
3. Unscrew fasteners and remove the power supply/fan assemblies.
4. Unscrew the fasteners and remove the sheetmetal cover.
5. On the circuit board, go to the B2 location (1 in Figure 13 on page 35) and
remove the BR1225 battery from the holder.

34 SAN06B-R Installation, Service, and User Guide


1

R15

R16
Y1

R13
R14
U23

Q1

R17
10

R11
2
C3 C4 C6

Q2
C1 C2

J51
F1 F2 C7

R12

C5
Q3

R6
R7

R8
R9
1 1
U1

9 9 C15

9
Q4

R10
U2

R5

U4
HDR2
16

15
L1 U3 D21
F4

C10
Y2 10 18 10 18

U37
C14
B1

R19
C13

R23

R24
R22

R25
R26
C11
Q5 Q6 Q8 Q9
HDR1 F3 U10 R18
R27 R29

U6
100 76 R28
1
2
75 C12
Q7
R20 C8 C9 R21 Q12

J47
U5

J2

C17
50 TP1 R32 R33
Q11
C23
9 10 R30
2

25

C25
R34
1 2 Q10
RP1
C16

C21

C22
U12 D3 TP3
U8 B2 C19 L4 U13

U171
L3

R35
45

R36
R37
U9 L5

J3
CR1 20 U14

C26
51
25 C2676 C36 L6

R31
U11

C2677
C2674
R2492
U25 C24
C18

R2490
C20 U26
U7

TP4 26 50
13 14
U15

TP2
R41

U174
R47

R50 U21
R40

R42

R49 U20 C33


C29
C30

U19 R51 U28


R39

D4

5
C27
C31 C34 C35
R43 R45 U173

R48
U16 U27
C28 35 U22 1 2
X1 U39
R38 10
Q48

1
R52 R53
R46

2
C32 D22
J5

J10
R44 U29 U30 U35
C37 U32 U34
R54 U17 U18 U48 Q14 C41

13 14
C38 U42 26 U41

R2486
R55 U31 U40
1 U33 Q13 U36

3
1
R57
J4

R2487

C48
C42
C43
C44
C45
C46
C47
C40

R58

J7
C39 R77 C74
R2483 R56 R78 C75 R59

R100
R88
R90
R92
R94
R96
R98

2
U43 U45 R85

C85
R2482
C49 R60 R66 C54 C60 U56
C69 R72 Q15
R79 U52 U53
C50 R61 R67 C55 C61 C76 U47
C65 C70 R73 R80 U49 U51

R89
R91
R93
R95
R97
C51 R62 R68 C56 C62 C77 C104
C66 C71 R74 R81 TP5

C102
C103
J6

U65
R63 C78

C88
C90
C93
C96
C99
C52 R69 C57 C63 U44

R983
D5
C67 C72 R75 R82 Q16 Q17
C79 C83

C101
C53 R64 R70 C58 C64 C82

C89
C92
C95
C98
C68 C73 R76 U50 U61 C84

C112
R83

C110

C116
R65 R71 C59 C80 U164

U55
R84

C100
C81

C91
C94
C97
R101 TP7 U63 U64
C107

C114
TP8

R982
C121
C123
C125
C127
C129
C119
C105 J*
R102 R129

R114
R86

R120
R122
R124

R128
R116
R118
L7 U59

R106
R130

R111
J9 C86

R108

R109
U62 R131

R115
C106 C87

R2000
C108 R132
U60 C115 R87

5
C111

R121
R123
R125
R127
R117
R119
L8

R203
C109 C117

R202
R103 R964 R107 C113
R146 R113 C118

C120
C122
C124
C126
C128
C130
C131
R104
C132 R105 TP6 R147
R135 R136 R148

1
R137 C138
R133 R138 C2390 R153

R1999
R2001
U67

R139 R154
U66

C2659 C2617
R140 U68 R163

R967
R968
R969
R141 C2658 R164
R142 C2391

U69

R2148

R2149
C148
U75

U71
R134
U70

C157
8
4 R149

C139
R150 C812 C813 R973
C133 X2
R151 1 C811 C814

C154

C155
C140
C141

C146
C147

C153
R152

C149
C150
9

C151
C152
C2635

R155 C156

C144
C145
12

C143
C142
R160
C2631
C2630

R1092
16
J11 TP9
C2634

C175
R1656

C184
2

J13
C174

C2386
16
U72

C158 C176
R2469

C172
C177

U138
C159 C160
U73 C168 C178 R161
R2502
R2455

R2456

C162 C164 R2317

C2387
C161
C165 C169 C179 R162

U76
C166 R2316 U77
C170
8
U81 U82
C167 C171 10 2
C180
C181

R156
R157
R158
R159

R1093
32
C182
9

TP10 C163 C173


C183
C189 C884 C885
C201 C205
1 15 C190 C206 R1165

R1166
R1161
R1163
C2639
C2638
C2643
C2642

C188 C193 C197 C207


25 J15 C194 C204 C208
16

C198 R174 U84

R184
R185
C199 C209 C1126
24

R165
17

R167 C195 R170


C185

C196 C200 C210


R1211
U79

R168 R172 C211 R179


R177

C203

C212
R166 R169

R186
R187
R188
R189
R190
R191
C191 R173 R180
R195
R196

U80

C202 R171 R178 R181


R1212 C192
R175 U92 R182
C213 R206 R183
R194

R197

TP11 Q18 Q19 Q20 Q21 R176


R1330 R207 R209 R220

R212
R213
R214
R215
R216
R210
R211
C224 R221

R2479
R200 C220

U94
R201

R2223 C225
C186
C187

C221 R1315 R208


C214 C216

U93
C222 C226 R217
R198 C223
R192 U86 U87 C227 R218 R222
C218 R219 R223
C217 C228 R224
U101

R2476

R2477
R2478
C215 U57 U96 U91 R225
C219 C229 R226
R193
R199 J8 C266 U98 C2388

R2474
U89

R2475

R227
R228
R229
U90 Q22 C267 C2389 U176
R2485 R205 C239 U97
R230 C231 U*
R247 R231 U83
R248 R258 U103
U100
C235

C230 R249 C268


R259

C275
C243
C244

C250
C251

C254
C255

C263
C264

C269
C270
C271
C272
C273
C274
C245
C246
C247
C276

C252

C253

C258
C259
C260

C265
R250 C232

C241
C242

C248
C249

C256
C257

C261
C262
C277 R260 U106
R2484

R251 R232

R240
R241
R242
R243
R244
R245
R246
C278

C240
R261 C236
C279 R233 C233
C314

C237
C234 R262 R2151 R273

R2150
R252 C281 C286 C300 L10
C291 R270
R253 C282 C287 C301 R271 R239 C341
C292 R272
U105

R2153
R2152
R254 C283 C288 C302 C2618
U108

C334 R282
U104

R277
R278
C321 R279
C325 R280
C329 R281

C336 C323
C327
C331
C335
C339
C340
C332 C320
C293 R274
R255 C284 C289 C303
C294 C310
R256 C285

U99
C304

C337

C324
C328
C311
C295 C305 C2607
U109

C296 R234
C312
R235 C2608 U107

C319
C322
C326
C330
C333
C338
C2606 C313
C297

R293
R295
R297
R299
R301
R303
R305
R263
C290

C2605 C2604 R306


R257 C298 R264 L11 C357 R275
R292

C280 R265 C355 R307


C2603 C315
R283 C299 C344 C356
R266 C347 C351 TP13 R308
C316
R267 R309
J16

R304
R294
R296
R298
R300
R302
L12 C348 C352 R276

U110
R268 C345 R2315
CR2

C342

C367
C359
C353 C317

C365
C358

C360
C361
C362
C363
C364

C366
R284 R287 C346 R2333
R288 C354 C318
R289
R290 TP12 R2313
L14
C343 R291
R286 R312
R285
R313

C376

C377
R2335

C375
R319

R314

R1714
R1713
R1712

R1710
R1709
R1708
R1707
R1706
R1705
R1704
R1703
R1702
R1701
R1711
CR3

L13

R310 R2493 C378


R315 TP15
C368 C2201
C2221
C2225
L15

R321
R311
C369 R316 U102 C374
Q23 U111 L174
R317

R320
TP14
U113 U24 R318 U115 C2222
C2678

C379 C2226
C382

C381 C383 C384 C2227


TP17
R322

R328 R329
U114

R355
R354
R330
C389
R327
C388
C2219

C2684
R2507
C2220
R323
R325

C2685
TP19
U118
C380

R383
R324
R326

U117
R384 R356

U119
TP16 TP18 TP22
U112 R382 TP21

C385

C386

R2508
R338
R339
R340
R341

U175
R364
R362
R344
R346
R347
R2510

R331
R381
R342

C387
U116 R380
U120 TP20 U38 C2683

R332
C2357
C2359

U54
50
R333

R375
25
R376 U125
D6

U124

R353
R377 C2358
L16
U123
U122

U121 R378
R334
R335
R336

C2382 C2356
CR4

45 R379

R352

R1814
R337

R348
R349

R350

R351
C2354
20 U127
C2353 C2383
R357
R358
R359
C395
C396
C397
C398
C391
C392
C393
C394

C399
C400
C401
C402

C403
C404
C405
C406
L19

L20

R366
L17

L18

L21

L22

L23

R361
R360
L24

R365
R345
R343
R363

R367 R369 R371 R373 R2136 R2138


C390

35
10 R368 R370 R372 R374 R2135 R2137
J18 J19 J20 J21
11

11
20

20

20

20
11

11

11

11

11
20

20

20
J17

26

r06b007
1
R385
R386
R387

U126
10

10

10

10
10
10

10
1

1
1

1
U129

U132

P1_10

P2_10

R2144
R2145
R2143
R389

R393

R397
R398

R401
R390
R391
R392

R394
R395
R396

R399
R400

R402
R403
R404

R2133
R2141
R2142
R2140
R2134
TP23

TP24

U131
P1_2

P2_2
U128
C443

C440 C442
J26
CR5

C439 C441
J27 U166
R388

U130
1 J28 4 R405
P1_9 P2_1
U135

Figure 13. Location of battery holder

6. Recycle the battery as appropriate.

Refer to the Environmental Notices and User Guide shipped with the product for
more information on battery recycling and disposal.

Chapter 3. Operating the SAN06B-R 35


36 SAN06B-R Installation, Service, and User Guide
Appendix A. Product specifications
Summary of switch components
The switch includes the following components:
v Cabinet-mountable 1U chassis designed to be mounted in a 19-in. cabinet space,
with forced-air cooling that flows from the nonport side of the switch to the port
side
v 16 active Fibre Channel ports, compatible with short wavelength (SWL), long
wavelength (LWL), and extended long wavelength (ELWL) SFP transceivers
v One Ethernet management port with 10/100/1000 Mbps autonegotiating
capability
v 6 optical GbE ports, compatible with short wavelength (SWL), long wavelength
(LWL), and extended long wavelength (ELWL) SFP transceivers.
v One IEEE-compliant RJ-45 serial cable cable, 10-ft (approximately 3 m) long. An
RJ-45 to DB9 adaptor is also provided with the switch.
v One IEEE-compliant RJ-45 connector on the port side of the switch for use with
a serial console and 10/100 MB/sec Ethernet
v Switch status and management LEDs: 1 switch power LED, 1 switch status LED,
2 Ethernet LEDs, 2 power supply/fan LEDs
v Port status LEDs: 16 Fibre Channel port status LEDs, 6 optical GbE port status
LEDs, and 2 LEDs (one each for fault and status/activity) per copper-capable
GbE port (total of 4 LEDs).
v 2 universal AC input and redundant power supplies with AC switches and
built-in fans

Weight and physical dimensions


Table 14 lists the weight and physical dimensions of the switch.
Table 14. Switch dimensions
Dimension Value
Height 4.45 cm (1.75 in.)
Depth 64.14 cm (25.25 in.)
Width 43.18 cm (17 in.)
Weight (with two power supplies and no 10.9 kg (24 lb)
SFPs installed)

© Copyright IBM Corp. 2009, 2013 37


Power supply
The power supplies are universal and capable of functioning worldwide without
voltage jumpers or switches. They meet IEC 61000-4-5 surge voltage requirements
and are autoranging in terms of accommodating input voltages and line
frequencies. Each power supply has a built-in fan for cooling, pushing air towards
the port side of the switch. Table 15 lists the power supply specifications for the
switch.
Table 15. Power supply specifications
Specification Value
Maximum output 150 Watts
System DC power Idle: 95 W
consumption (excluding Maximum: 116 W
power supply/fan
units)
Input system power Idle: 145 W
(including power Maximum: 173 W
supply/fan units)
Input voltage 85-264 V ac, Universal
Input line frequency 47-63 Hz
BTU rating 590 BTU/hr
Inrush current Maximum of 60 amps for period between 10-150 ms
Input line protection Both AC lines are fused

Environmental requirements
Table 16 lists the acceptable environmental ranges for both operating and
non-operating (such as during transportation or storage) conditions.
Table 16. Environmental requirements
Condition Acceptable range during operation Acceptable range during
non-operation
Ambient 0° to + 40°C (32° to 104°F) -25° to 70°C (-13° to 158°F)
temperature
Humidity 10% to 85% RH non-condensing, at 40°C 10% to 90% RH non-condensing,
(104°F) at 70°C (158°F)
Altitude 0 to 3 km (9,842 ft) above sea level 0 to 12 km (39,370 ft) above sea
level
Shock 20 G, 6 ms, half-sine wave 15 G, 12-18 milliseconds,
trapezoid
Vibration 0.5 G sine, 5-500 Hz 2.0 G sine, 5-500 Hz
Air flow Maximum: 101.94 cmh (60 cfm) NA
Nominal: 74.76 cmh (44 cfm)

38 SAN06B-R Installation, Service, and User Guide


Data transmission ranges
Table 17 provides the data transmission ranges for different cable types and port
speeds for Fibre Channel. Up to 500km at 1G is supported when using a long
distance transport system such as DWDM.
Table 17. Fibre channel data transmission ranges by cable type and port speed
Cable size Extended long
Port speed (microns) Short wavelength (SWL) Long wavelength (LWL) wavelength (ELWL)
1 Gbps 50 500 m (1,640 ft) (OM2) NA NA
860 m (2,821 ft) (OM3)
62.5 300 m (984 ft) NA NA
9 NA 10 km (6.2 mi) 80 km (50 mi)
2 Gbps 50 300 m (984 ft) (OM2) NA NA
500 m (1,640 ft) (OM3)
62.5 150 m (492 ft) NA NA
9 NA 10 km (6.2 mi) 80 km (50 mi)
4 Gbps 50 150 m (492 ft) (OM2) NA NA
380 m (1,246 ft) (OM3)
62.5 70 m (230 ft) NA NA
9 NA 10 km (6.2 mi) NA
8 Gbps 50 50 m (164 ft) (OM2) NA NA
150 m (492 ft) (OM3)
62.5 21 m (69 ft) NA NA
9 NA 10 km (6.2 miles) NA

Table 18 provides the data transmission ranges for different cable types for Gigabit
Ethernet (GbE).
Table 18. Gigabit Ethernet data transmission ranges
Cable
size Long wavelength
Port speed (microns) Short wavelength (SWL) (LWL)
1 Gbps 50 500 m (1,640 ft) (OM2) NA
860 m (2,821 ft) (OM3)
62.5 300 m (984 ft) NA
9 NA 4 km (2.48 miles)

Table 19 provides the data transmission ranges for different cable types for
copper-cabled Ethernet and GbE RJ-45 ports.
Table 19. Copper cabling and RJ-45 data transmission ranges
Port speed Cable type Range
1 Gbps Cat-5 100m

Appendix A. Product specifications 39


Memory specifications
The switch has three types of memory devices with the following capacities:
v Boot flash: 4 MB
v Compact flash: 1 GB
v Main memory (SDRAM): 2 GB

Port specifications

Fibre Channel port specifications


The Fibre Channel ports in the switch are compatible with SWL, LWL, and ELWL
SFP transceivers. The strength of the signal is determined by the type of
transceiver in use. The ports are capable of operating at 1 Gbps, 2 Gbps, or 4 Gbps
and are able to auto-negotiate to the maximum link speed.

GbE port specifications


The GbE ports in the switch are compatible with short range (SR) and long range
(LR) SFP transceivers. The strength of the signal is determined by the type of
transceiver in use. These ports are capable of operating at up to 1 Gbps. The 8
virtual FCIP Fibre Channel links over each physical Ethernet connection share this
bandwidth.

Serial port specifications


The serial port is located on the port side of the switch. The switch uses an RJ-45
connector for the serial port. An RJ-45 to DB9 adaptor is also provided with the
switch.

Note: To protect the serial port from damage, keep the cover on the port when not
in use.

The serial port can be used to connect to a workstation to configure the switch IP
address before connecting the switch to a fabric or IP network. The serial port
parameters are fixed at 9600 baud, 8 data bits, and no parity, with flow control set
to None.

Table 20 lists the serial cable pinouts.


Table 20. Serial cable pinouts
PIN Signal Description
1 Not supported NA
2 Not supported NA
3 UART1_TXD Transmit data
4 GND Logic ground
5 GND Logic ground
6 UART1_RXD Receive data
7 Not supported NA
8 Not supported NA

40 SAN06B-R Installation, Service, and User Guide


Parts list (CRUs)
The parts in listed Table 21 can be replaced by a customer. Refer to Chapter 3,
“Operating the SAN06B-R,” on page 25 for information on interpreting LED
patterns and diagnostics and troubleshooting procedures to determine the status of
components. Refer to Figure 1 on page 3 and Figure 3 on page 4 for the location of
the parts listed below. Part numbers are subject to change, particularly for SFP
transceivers. Contact your IBM representative for current information on part
numbers for SFPs to meet your needs.

| Attention: Use only transceivers that are supported for this product. Only
| transceivers purchased from IBM are supported. The use of transceivers that are
| not supported may cause data loss or cause the product to malfunction. For a
| listing of transceivers compatible with this product:
| v Go to the IBM Support Portal www.ibm.com/supportportal.
| v In the Search field, enter b-type supported transceiver.
| v Alternatively, use this direct link: http://www-01.ibm.com/support/
| docview.wss?uid=ssg1S1004421.
Table 21. CRU part numbers
Part
number Description
45W5481 Switch chassis assembly (replacement of chassis is required if internal circuitry
fails)
45W0319 Power supply/fan assembly

Appendix A. Product specifications 41


42 SAN06B-R Installation, Service, and User Guide
|

| Appendix B. Link troubleshooting


| IBM SAN b-type directors and switches use the latest high bandwidth Fibre
| Channel technology and auto-negotiate to 16 Gbps, 8 Gbps, 4 Gbps, or 2 Gbps
| based on the link data rate capability of the attached transceiver and the speed
| supported by the switches and directors. Negotiation to 1 Gbps is not supported
| unless 4 Gbps FC transceivers are used. As the 8 and 16 Gbps channel is more
| sensitive to the condition of the existing multimode and single mode cable plant, it
| is very important to minimize connector reflections and maintain an acceptable
| link loss budget.

| This section provides link troubleshooting advice on fault isolation and provides
| guidance in the following areas:
| v Dust and dirt contamination
| v Link loss
| v Attenuation on LWL connections
|
| Fault isolation
| Since a job loss issue can be caused by a variety of problems, it is important to
| employ a systematic fault isolation process to remedy the issue. Note that job
| losses do not necessarily result from link errors. They may also be due to:
| v Configuration issues
| v Networking overload
| v Failures on storage device, switch, or server

| Assume for these procedures that the observed errors originate from link errors
| and are not the result of configuration issues, network overload or network
| equipment failures.

| Whenever CRC errors are discovered on a particular link, it is easy to jump to the
| conclusion that the link is causing the network issue. This might not be the case.
| Since CRC errors are just symptoms of a link issue, we need to trace the
| propagated error to where it originated.

| Figure 14 shows a simplified network involving a server, a switch, and a storage


| device. In this example, assume that the server experienced an error at port 1. This
| observable error can potentially originate from links 1, 2, 3, or 4 and/or SFP 1, 2, 3,
| or 4.
|
|
Server Switch Storage

Link 1 Link 2
Tx Rx Tx Rx
Port 1

Port 5

Port 6

Port 9
SFP 1

SFP 2

SFP 3

SFP 4

b965036

Link 4 Link 3
Rx Tx Rx Tx

|
| Figure 14. Identifying the origin of failure
|
| To determine the original failing link, the observable CRC error needs to be
| tracked back to the first occurrence of the CRC error. By following this process, it

© Copyright IBM Corp. 2009, 2013 43


| is discovered in this example that CRC errors observed in link 4 were propagated
| from link 3, which in turn originated from link 2.

| Once the original failing link (link 2) has been determined, the two connecting
| ports of that link need to be checked for the following errors:
| v Encoder errors
| v Disparity errors
| v Invalid transmission words
| The port that displays any of the above errors is the cause of the link issue, which
| can be caused by dust or dirt in the connectors or fiber, an insufficient link loss
| budget, and/or incompatible SFPs.
|
| Dust, dirt, or other contaminants
| One of the most common optical link problems is caused by dust, dirt, or oil in the
| connectors and fiber. 8 and 16 Gbps links are more prone to such issues while
| lower link data rates, such as 1, 2, or 4 Gbps may be unaffected.

| Once the failing port has been identified by following the above fault isolation
| process, the receive power of the transceiver sitting in that port needs to be
| determined. An abnormally low receive power usually means that the physical link
| is dirty.

| The receive power can be checked by querying the SFP diagnostics data via the
| command line interface. This information will provide a rough gauge whether the
| receive power is abnormally lower than the minimum receive specification of the
| transceiver. It is also prudent to compare this receive power with those of
| neighboring transceivers.

| For better accuracy, it is advisable to use a power meter to measure the actual
| receive power of the link. If you are experiencing excessive bit errors and the
| receive power of the transceiver is abnormally low, it is recommended that you:
| v Re-seat the transceivers for the failing link
| v Clean the connector and optical fiber
| Most link issues are solved by completing these steps.
|
| Best practices for minimizing link loss
| The "link margin" or the "power budget" of the link is a measure of signal power
| gain or loss expressed in decibels (dB). Maintaining a healthy link budget is critical
| to establishing a reliable and stable network.

| Follow these best practices for minimizing link loss:


| v Stay well within the maximum cable distance calculated for the link.
| v Apply typical or worst-case values during loss calculations.
| v Use the highest grade cabling components for the application to be supported.
| v Match the cable type with the wavelength, bandwidth, and distance to be
| supported; do not mix cable types within a link.
| v Inspect loss ratings of all cabling components during the selection process.
| v Record loss measurements for horizontal and vertical cable runs during
| installation.

44 SAN06B-R Installation, Service, and User Guide


| v Become familiar with how to quickly determine the link budget and link loss of
| selected sections of the cabling.
| v Account for power loss associated with future repairs and expansion.
| v Do not stress the cables.
| v Prototype a link with anticipated maximum cable distance and selected
| components—and then take measurements to calculate the actual link loss
|
| Attenuation on LWL connections
| In the datacenter environment, there may be 8 Gbps or 4 Gbps LWL transceivers
| that are connected to 2 Gbps LWL transceivers using single-mode fiber over short
| distances. Such connections need to be optically engineered because there is a
| possibility that the transmit power of the 8 Gbps / 4 Gbps LWL transceivers may
| saturate the receiver of 2 Gbps LWL transceivers and cause CRC errors.

| Attention: This discussion does not apply to 16 Gbps transceivers since


| connections between 16 Gbps and 2 Gbps transceivers is not supported.

| Refer to Table 22 for the typical specifications of maximum transmit and receive
| power of LWL transceivers. This information is also available in the information
| technology industry standard "Fibre Channel – Physical Interface-4 (FC-PI-4)"
| document.
| Table 22. Specifications of LWL 10km transceivers
| LWL SFP/SFP+ 2GFC 4GFC 8GFC
| Power, Tx (max) dB -3 -1 +0.5
1
| Power, Rx (max) dB 0 or -3 N/A N/A
1
| The maximum receive power specifications of some 2 Gbps LWL 10km transceivers can
| vary from 0dB to -3dB. However, most 2 Gbps 10km transceivers specify a maximum
| receive power of 0dB.
|

| It is important to check the maximum receive power of the 2 Gbps LWL


| transceiver in the manufacturer's datasheet.

| Without taking into account connector and fiber losses, the transmit power of 8
| Gbps / 4 Gbps LWL transceivers may be observed to overdrive the -3dB maximum
| receive power of 2 Gbps LWL transceivers. If the maximum receive power of the 2
| Gbps LWL transceiver is 0dB, a 4 Gbps LWL transceiver with a -1dB transmit
| power will not overdrive the 2 Gbps transceiver. Although some 8 Gbps LWL
| transceivers may reduce their transmit power to 4 Gbps levels, this may still
| overdrive a 2 Gbps LWL transceiver.

| Best Practice for LWL connections – Optically engineer a


| long-distance connection
| It is always a good practice to optically engineer a long-distance connection. Most
| link issues caused by SFP incompatibility can be solved either by use of 4 Gbps
| LWL transceivers or use of 8 Gbps LWL transceivers that employ rate select.

| 2G LWL SFP maximum receive power


| The IBM SAN b-type 8 Gbps and 16 Gbps directors and switches use the latest
| high bandwidth Fibre Channel technology and auto-negotiate to 16 Gbps, 8 Gbps,
| 4 Gbps, or 2 Gbps based on the link data rate capability of the attached transceiver.

Appendix B. Link troubleshooting 45


| Negotiation to 1 Gbps is not supported. Since 8 and 16 Gbps equipment is more
| sensitive, the existing cable plant may require additional attention to cable care
| after upgrading from 2 or 4 Gbps fibre. In a few cases, the Tx power of the switch
| can be higher than the connected equipment. In nearly all of those cases, there is
| enough attenuation in the existing cable plant so as not to require additional
| attenuation. The common 2 Gbps SFP Rx maximum power levels are listed in
| Table 23 and can be used as a quick method to relieve concerns of over saturation.
| Table 23. Maximum receive power of 2 Gbps LWL SFPs
| Max Receive Power
| Vendor Part number Description (dB)
| Avago AFCT-57M5ATPZ 2 Gbps 10 km SFP -3 dB
| Finisar FTLF1319P1xTL 2 Gbps 10 km SFP 0 dB
| Finisar FTRJ1319P1xTL 2 Gbps 10 km SFP 0 dB
| JDSU JSH-12L1DD1 2 Gbps 10 km SFP 1 dB
| Hitachi Cable HTR6517 2 Gbps 10 km SFP -3 dB
| Optoway SPS-9110FG 2 Gbps 10 km SFP -3 dB
| Optoway SPS-9110AFG 2 Gbps 10 km SFP -3 dB
| JDSU JSH-21L3AR3 2 Gbps 10 km SFP 1 dB
| E20 ES212-LP3TA 2 Gbps 10 km SFP -3 dB
|

46 SAN06B-R Installation, Service, and User Guide


|

Notices
This information was developed for products and services offered in the USA.

IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe on any IBM intellectual property right
may be used instead. However, it is the user's responsibility to evaluate and verify
the operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing to:

IBM Director of Licensing


IBM Corporation
North Castle Drive
Armonk, N.Y. 10504-1785
U.S.A.

For additional information, visit the web at:


http://www.ibm.com/ibm/licensing/contact/

The following paragraph does not apply to the United Kingdom or any other
country where such provisions are inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this statement may not apply
to you.

This information could include technical inaccuracies or typographical errors.


Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.

Any references in this information to non-IBM web sites are provided for
convenience only and do not in any manner serve as an endorsement of those web
sites. The materials at those web sites are not part of the materials for this IBM
product and use of those web sites is at your own risk.

IBM may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.

Any performance data contained herein was determined in a controlled


environment. Therefore, the results obtained in other operating environments may
vary significantly. Some measurements may have been made on development-level

© Copyright IBM Corp. 2009, 2013 47


systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurement may have been
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.

Information concerning non-IBM products was obtained from the suppliers of


those products, their published announcements or other publicly available sources.
IBM has not tested those products and cannot confirm the accuracy of
performance, compatibility or any other claims related to non-IBM products.
Questions on the capabilities of non-IBM products should be addressed to the
suppliers of those products.

If you are viewing this information in softcopy, the photographs and color
illustrations may not appear.

48 SAN06B-R Installation, Service, and User Guide


Trademarks
IBM, the IBM logo, and ibm.com® are trademarks or registered trademarks of
International Business Machines Corporation in the United States, other countries,
or both. A complete and current list of other IBM trademarks is available on the
Web at http://www.ibm.com/legal/copytrade.shtml

Adobe, the Adobe logo, PostScript, and the PostScript logo are either registered
trademarks or trademarks of Adobe Systems Incorporated in the United States,
and/or other countries.

Java and all Java-based trademarks and logos are trademarks of Sun Microsystems,
Inc. in the United States, other countries, or both.

Linux is a registered trademark of Linus Torvalds in the United States, other


countries, or both.

Microsoft and Windows are trademarks of Microsoft Corporation in the United


States, other countries, or both.

UNIX is a registered trademark of The Open Group in the United States and other
countries.

Other product and service names might be trademarks of IBM or other companies.

Notices 49
Electronic emission notices
The following statements apply to this product. The statements for other products
intended for use with this product will appear in their accompanying manuals.

Federal Communications Commission (FCC) Class A


Statement
This equipment has been tested and complies with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.

Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes
or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Industry Canada Class A Emission Compliance Statement


This Class A digital apparatus complies with Canadian ICES-003.

Avis de conformité à la réglementation d'Industrie Canada


Cet appareil numérique de la classe A est conform à la norme NMB-003 du
Canada.

European Union EMC Directive Conformance Statement


This product is in conformity with the protection requirements of EU Council
Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. IBM cannot accept responsibility for any
failure to satisfy the protection requirements resulting from a non-recommended
modification of the product, including the fitting of non-IBM option cards.

Attention: This is an EN55022 Class A product. In a domestic environment this


product may cause radio interference in which case the user may be required to
take adequate measures.

Responsible manufacturer:
International Business Machines Corp.
New Orchard Road
Armonk, New York 10504
Tel: 919-499-1900

European community contact:


IBM Technical Regulations, Department M456
50 SAN06B-R Installation, Service, and User Guide
IBM-Allee 1, 71137 Ehningen, Germany
Tel: +49 7032 15-2937
E-mail: [email protected]

Germany Electromagnetic Compatibility Directive


Deutschsprachiger EU Hinweis:

Hinweis für Geräte der Klasse A EU-Richtlinie zur Elektromagnetischen


Verträglichkeit

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie


2004/108/EG zur Angleichung der Rechtsvorschriften über die elektromagnetische
Verträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022
Klasse A ein.

Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu


installieren und zu betreiben. Des Weiteren dürfen auch nur von der IBM
empfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung für
die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der
IBM verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung der IBM gesteckt/eingebaut werden.

EN 55022 Klasse A Geräte müssen mit folgendem Warnhinweis versehen werden:


"Warnung: Dieses ist eine Einrichtung der Klasse A. Diese Einrichtung kann im
Wohnbereich Funk-Störungen verursachen; in diesem Fall kann vom Betreiber
verlangt werden, angemessene Maßnahmen zu ergreifen und dafür
aufzukommen."

Deutschland: Einhaltung des Gesetzes über die elektromagnetische


Verträglichkeit von Geräten

Dieses Produkt entspricht dem "Gesetz über die elektromagnetische Verträglichkeit


von Geräten (EMVG)". Dies ist die Umsetzung der EU-Richtlinie 2004/108/EG in
der Bundesrepublik Deutschland.

Zulassungsbescheinigung laut dem Deutschen Gesetz über die


elektromagnetische Verträglichkeit von Geräten (EMVG) (bzw. der EMC EG
Richtlinie 2004/108/EG) für Geräte der Klasse A

Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das
EG-Konformitätszeichen - CE - zu führen.

Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller:
International Business Machines Corp.
New Orchard Road
Armonk, New York 10504
Tel: 919-499-1900

Der verantwortliche Ansprechpartner des Herstellers in der EU ist:


IBM Deutschland
Technical Regulations, Department M456
IBM-Allee 1, 71137 Ehningen, Germany
Tel: +49 7032 15-2937
E-mail: [email protected]

Notices 51
Generelle Informationen:

Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse
A.

People's Republic of China Class A Electronic Emission


Statement

Japan VCCI Council Class A Statement

Translation: This is a Class A product based on the standard of the VCCI Council.
If this equipment is used in a domestic environment, radio interference may occur,
in which case, the user may be required to take corrective actions.

Japan Electronics and Information Technology Industries


Association (JEITA) Statement
Japanese Electronics and Information Technology Industries Association (JEITA)
Confirmed Harmonics Guideline (products less than or equal to 20 A per phase).
jjieta1

Korea Communications Commission (KCC) Statement


Please note that this equipment has obtained EMC registration for commercial use.
In the event that it has been mistakenly sold or purchased, please exchange it for
equipment certified for home use.

52 SAN06B-R Installation, Service, and User Guide


Russia Electromagnetic Interference (EMI) Class A Statement

rusemi
Australia and New Zealand Class A Statement
Attention: This is a Class A product. In a domestic environment this product
might cause radio interference in which case the user might be required to take
adequate measures.

Notices 53
54 SAN06B-R Installation, Service, and User Guide
Index
A domain ID 18 IBM (continued)
notices 47
accessibility trademarks 49
IBM commitment v
keyboard navigation iv E installation
electrical requirements 8
vendor software iv edition notice ii
environmental requirements 8
address electrical requirements 8
instructions 9
IBM v electronic emission notices 50
SFPs 21
attention notices environmental
slide-rail rack 9
definition xviii notices xiii, xxi
stand-alone unit 8
example xviii product recycling and disposal xxi
switch 7, 8
requirements 8, 38
intellectual property 47
error log 5
IP address
B Ethernet
connection
dynamic 17
backing up switch configuration 23 setting 17
creating 18
battery removal 34 static 17
logging in 18
Brocade items included with switch 7
Gigabit ports
documents xxiii copper 29
location 3
optical 28 K
C specifications 40 keyboard navigation iv
cables management port
connecting 21 LED patterns 27
management 15 location 3 L
optical 15 labels, safety xviii
planning 15 LEDs
routing 15 F activity 25
SFPs 21 fan assembly Ethernet management port 27
caution notices LED patterns 29 fan status 29
definition xvi location 4 Fibre Channel port status 28
examples xvi replacing 32 GbE copper port status 29
chassis name 18 status 31 GbE optical port status 28
comments, sending to IBM v FCIP, configuring 20 location 25, 29
components features 2 nonport side 29
monitoring 25 Fibre Channel ports port side 25
summary 37 configuring routing services 20 power status 26
configuration, backing up 23 location 3 power supply status 29
configuring specifications 40 system status 27
FCIP 20 status LEDs 28 license
Fibre Channel routing services 20 functions 2 agreement iv
switch 7, 15 keys
creating a serial connection 16 adding 24
CRUs
power supply/fan assembly 31, 41 G backup 23
managing 23
status 31 getting help iii
optionally licensed features 3, 23
switch chassis assembly 41 Gigabit Ethernet
paperpack 8, 23
copper port status 29
removing 24
optical port status 28
viewing 24
D ports, location 3
optionally licensed features 2
danger notices xiii upgrade 2
data transmission ranges 39 license, for patents 47
date, setting 19 H local time 19
DHCP 17 help iii
diagnostic tests 31
dimensions 37 M
director of licensing, address 47 I management functions 5
disposal xxi IBM managing
documentation accessibility commitment v license keys 23
Brocade xxiii address v switch 25
IBM xxiii documentation xxiii memory 40

© Copyright IBM Corp. 2009, 2013 55


monitoring
components 25
R V
CRU status 31 rack safety xix, xx vendor software iv
device status 31 rack-mount kit 9, 10
read this first iii
recycling xxi
renaming
W
N chassis 18
Web sites iii
name weight 37
switch 18
chassis 18
switch 18
network time protocol 19
nonport side of the switch
S
components 4 safety
LEDs 29 labels xiii
notices notices xiii
attention xviii pre-installation 8
caution xvi rack xix, xx
danger xiii serial connection
edition ii creating 16
environmental xiii, xxi UNIX 16
general 47 Windows 16
IBM 47 serial ports
patents 47 location 3
safety xiii specifications 40
types xiii SFPs 21
NTP time synchronization 19 site preparation 8
slide-rail rack 9
stand-alone unit 8
switch
O components 37
optical cables 15 configuration 7
configuration backup 23
diagnostics 31
P dimensions 37
parts supplied with rack-mount kit 10 domain ID 18
patents 47 features 2
physical dimensions 37 functions 2
port side of the switch installation 7
components 3 items included 7
LEDs 25 library xxiii
ports managing 25
Ethernet management 3 name 18
Fibre Channel 3, 40 nonport side 4
Gigabit Ethernet 3, 40 port side 3
illustration 3 powering off 34
serial 3, 40 providing power 16
USB 3 troubleshooting 31
POST 5, 30 verifying correct operation 22
power weight 37
battery removal 34 synchronizing local time 19
cord 4 system status LEDs 27
providing to switch 16
status LEDs 4, 26
supply T
LED patterns 29 terminal emulator 16
location 4 time
replacing 32 required for installation 9
specifications 38 synchronization 19
status 31 zone 19
switch 4 trademarks 49
turning off switch 34 troubleshooting 31
power-on self-test 5, 30
preparing site for installation 8
product specifications 37
pull-out tab 3
U
USB port 3

56 SAN06B-R Installation, Service, and User Guide




Part Number: 98Y5370

Printed in USA

(1P) P/N: 98Y5370

GC27-2270-02
Spine information:

Service information: 2498


 IBM System Storage SAN06B-R SAN06B-R Installation, Service, and User Guide / R06

You might also like