Scribd
Upload
4 views9 pages

GRBL_LASER_CNC-_Controller_Manual_V1.1-min

manual de control cnc

Uploaded by

Canito Cano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
4 views9 pages

GRBL_LASER_CNC-_Controller_Manual_V1.1-min

manual de control cnc

Uploaded by

Canito Cano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

GRBL LASER CNC Controller Manual V1.

GRBL LASER CNC Controller Manual V1.1

The motion control card for machine control, with

strong professional.Requires the operator to have the

relevant expertise! When using a laser, you need to

be protected against laser damage to your eyes. Before using the tool

for engraving, familiar with the software operation, be careful to

operate to prevent accidents.


GRBL LASER CNC Controller Manual V1.1

Contents
Contents ................................................................................................................................... 2

Features: .................................................................................................................................. 3

Basic connection diagram (an Overview): ................................................................................ 4

Mechanical dimensions diagram:............................................................................................. 5

CNC LASER Control mode selection：...................................................................................... 6

Laser interface output voltage selection ： ............................................................................ 6

Driver microstep Selection： ................................................................................................... 6

Spindle motor wiring diagram： ...................................................................................... 7

Probe,limit switch wiring: .............................................................................................. 8

How to control relay and laser work ........................................................................................ 8

A4988 driver board, the output current adjustment method： .............................................. 8


GRBL LASER CNC Controller Manual V1.1

Features:
1. Application：use for DIY mini Engraving machine or Toy laser engraving machine

2. Applicable software：GRBL control、Un Gcode Sender、 GRBL controller.

3. Communication:USB（USB-CH340）.

4. Power supply: voltage: 12V current about 4A , according to the load to increase or

decrease the power supply.

5. Stepper motor driver: A4988 motor driver,16 microstep 1.5A phase current output

6. Support stepper motor: NEMA17 NEMA23 stepper motor, phase current less than

1.5A .

7. Laser interface: 12V or 5V, power less than 18W laser module.

8. Spindle motor interface: the maximum support 400W DC spindle motor.

9. With fan interface and TTL signal output interface (for controlling the laser module with

TTL module).

10. Limit interface: 3-axis limit interface.

11. Probe interface: for Z axis tool zero.

12.Power interface: DC-005 2.0 interface


GRBL LASER CNC Controller Manual V1.1

Basic connection diagram (an Overview):


GRBL LASER CNC Controller Manual V1.1

Mechanical dimensions diagram:


67.5mm
78.6mm

70.9mm

75mm
GRBL LASER CNC Controller Manual V1.1

CNC LASER Control mode selection：


Controller has a selector jumper, select the CNC mode, Controller control relay work, select

LASER mode, Controller control the laser interface, fan interface output. As shown below:

Laser interface output voltage selection ：


DIY commonly used laser module supply voltage 12V and 5V, Controller provides two kinds of

voltage options, according to the need to choose, as shown below:

Driver microstep Selection：


Microstep selector jumper under the X-axis driver board, remove the driver board to select

microstep, the factory default for 16 microstep. The Jumper location and microstep table are as

follows:：

Jumper location Microstep

16
GRBL LASER CNC Controller Manual V1.1

Spindle motor wiring diagram：


Use the relay on the controller to control the spindle to start and stop, the maximum can be

connected 400W DC Motor wiring as shown below:


GRBL LASER CNC Controller Manual V1.1

Probe,limit switch wiring:


1> At the command line, enter: $ 21 = 1, start the limit function, limit wiring as shown below:

2> Input probe code: G38.2 Z-20 F3, Z axis start probe, the probe device wiring as follows:

How to control relay and laser work


Code M3 controls the relay and laser output, M5 turns off the relay and laser, and can also
be realized by operating the buttons on the software.

A4988 driver board, the output current adjustment method：


Clockwise rotation of the potentiometer on the drive board, the output current increases,

counterclockwise rotation potentiometer, the current decreases. Measure the voltage between

the potentiometer and GND, calculate the specific current value, as shown below:
GRBL LASER CNC Controller Manual V1.1

I=V/0.8
Output phase current:

You might also like