JD-8 Motor Protector P- 248

1. General
JD-8 motor protector (“protector” in short) is mainly used for overload
and phase loss protection of continous duty or non-continous duty
AC motor with AC frequency of 50Hz, rated insulation voltage below
AC690V and rated operating current of 0.5A~160A.
Standards:IEC 60947-4-1

2. Type designation

JD -

Design serial number

Motor protector

JD-8 Motor
Protector
3.Key Technical Parameters

Table 1 Ambient Conditions

Normal use conditions Ambient temp.: -5℃ ~+40℃ ; average value within 24h not exceeding +35℃ ; altitude not exceeding 2,000m.

Atmospheric conditions RH shall not exceed 50% when maximum temperature is +40℃ ; in case of lower temperature, higher RH is allowed. Measures should be taken
against occasional condensation due to temperature change.

Installation category Ⅲ

Transport and storage conditions -25℃ ~+55℃

Table 2 Product specifications and key technical parameters Table 3 Main Circuit Technical Parameters

JD-8 JD-8 JD-8 JD-8 JD-8

Model JD-8 Product Model
0.5A~5A 2A~20A 20A~80A 32A~80A 64A~160A
Rated current (A) 80 80 80 160 160 Rated insulation voltage 690V
Current setting range (A) 0.5~5 2~20 20~80 32~80 64~160 Rated impulse withstand
voltage Uimp 4kV
Applicable motor power (kW) 0.25~2.5 1~10 10~40 16~40 32~80 Rated conditional short- 30kA
Installation method Molded case circuit current
Enclosure protection class IP00
Setting method Knob (if applicable)
Display method LED Pollution class Class 3
Protection functions Overload, loss of phase Rated duty 8h duty or non-stop duty

Contact number 1 NC set (solid output) Electromagnetic B

environment (EME)

Table 4 Auxiliary Circuit Technical Parameters

Product specifications JD-5/5, JD-5/20, JD-5/80, JD-5/200, JD-5/400

Rated insulation voltage (V) 380V

Rated impulse withstand voltage Uimp(kV) 2.5kV

Contact capacity Ue/Ie:41V/0.95A,24V/1.5A;Ith:5A

 P- 249 Motor Protector JD-8

4. Others
4.1 Structure characteristics
4.1.1 Three-phase electronic type
4.1.2 Function of phase failure and overload protection(not suitable for reversible motor)
4.1.3 Device capable of continuously adjusting setting current
4.1.4 The main circuit adopts pass-through-core type wiring method.
4.1.5 Installation method: installation via screws
4.2 The protector has the following operating characteristics for load balance of each phase; the tripping level is level 30.

Serial number Multiple of setting current Actuation time Starting condition Ambient air temperature
1 1.05 No actuation within 2h Cold state
2 1.2 Actuation within 2h Hot state(the test is done Room temperature
3 1.5 Actuation within 12min following sequence 1) (20±5)℃

4 7.2 9s<tp≤30s Cold state

4.3 Wiring diagram Wiring diagram of control circuit with voltage AC380V
Wiring diagram of control circuit with voltage AC220V

L1 L2 L3 N
L1 L2 L3

ST
FU STP 95 96 ST
FU STP 95 96

KM KM
KM KM
FU
KM FU
KM
JD-8
JD-8

M
M

5. Overall and mounting dimensions (mm)

JD-8(0.5A~5A,2A~20A,20A~80A)

95 96

66±0.43 Φ12
68max

2/T1 4/T1 6/T1

40±0.28
51max

JD-8 MOTOR INTEGRATE D PROTEC TOR

AB C Overload
Curren t settin g

52
R2.2 91max

JD-8(32A~80A,64A~160A)

95 96
96±0.5
Φ20
76max

2/T1 4/T1 6/T1

46±0.32

LL1 2 L3
57max

FU
JD-8 MOTOR INTEGRATE D PROTEC TOR
KM FU KM

AB CO verl oad
Current settin g M

R3.5 80
125max