Lutz Drum and Container Pumps

Pump tube SS (stainless steel) for highly flammable liquids

Productdetail Pump tube SS-SL SS-MS

Type of impeller: Impeller Rotor Impeller Rotor

Category 1 / 2 (acc. to ATEX) yes yes yes yes
Immersion tube diameter: up to mm 41 41 41 41
Temperature of medium: up to °C 100 100 100 100
Material: Pump tube 1.4571 1.4571 1.4571 1.4571
Impeller/Rotor ETFE ETFE ETFE ETFE
Hose connection: Nominal diameter mm 19-32 19-32 19-32 19-32
Outer thread G 1 1/4 G 1 1/4 G 1 1/4 G 1 1/4
Length: 700 mm* Order No. 0150-003 0150-000 0151-003 0151-000
Length: 1000 mm* Order No. 0150-004 0150-001 0151-004 0151-001
Length: 1200 mm* Order No. 0150-005 0150-002 0151-005 0151-002
Length: 1400 mm* Order No. 0150-108 0150-113 – –
Length: 1500 mm* Order No. 0150-109 0150-114 – –
Length: 1600 mm* Order No. 0150-110 0150-115 – –
Length: 1700 mm* Order No. 0150-111 0150-116 – –
Length: 2000 mm* Order No. 0150-112 0150-117 – –
*The lenght complies approx. to dimension C in the dimension table. Special lengths 200–2500 mm on request

Choice of motors Operating data

ME II 3 Characteristic curve no. 453 452 453 452

Output: 460 W 460 W Flow rate1 up to l/min. 95 178 95 178
Voltage: 230 V 230 V Delivery head up to m wc 14 9 14 9
LVR.: yes no Viscosity up to mPas 350 200 350 200
Density: up to kg/dm³ 1.6 1.2 1.6 1.2
Order No. 0050-000 0050-016 Weight (kg) Motor + pump tube 8.7 8.7 8.7 8.7

ME II 5 Characteristic curve no. 455 454 455 454

Output: 580 W 580 W Flow rate1 up to l/min. 100 190 100 190
Voltage: 230 V 230 V Delivery head up to m wc 16 10 16 10
LVR.: yes no Viscosity up to mPas 700 550 700 550
Density: up to kg/dm³ 1.8 1.3 1.8 1.3
Order No. 0050-001 0050-017 Weight (kg) Motor + pump tube 9.6 9.6 9.6 9.6

ME II 7 Characteristic curve no. 457 456 457 456

Output: 795 W 795 W Flow rate1 up to l/min. 115 210 115 210
Voltage: 230 V 230 V Delivery head up to m wc 20 13 20 13
LVR.: yes no Viscosity up to mPas 500 400 500 400
Density: up to kg/dm³ 1.9 1.4 1.9 1.4
Order No. 0050-002 0050-018 Weight (kg) Motor + pump tube 10.8 10.8 10.8 10.8

ME II 8 Characteristic curve no. 459 458 459 458

Low-voltage release (LVR.): Flow rate1 123 243 123 243
Prevents the pump from starting
Output: 930 W 930 W up to l/min.
up again without warning after a Voltage: 230 V 230 V Delivery head up to m wc 26 15 26 15
power failure. In the hazardous LVR.: yes no Viscosity up to mPas 750 650 750 650
location, motors with low-
voltage release are absolutely Density: up to kg/dm³ 1.9 1.4 1.9 1.4
prescribed. Order No. 0050-042 0050-041 Weight (kg) Motor + pump tube 10.8 10.8 10.8 10.8

MD1xL MD2xL Characteristic curve no. 461 460 461 460

Output: 1000 W 1000 W Flow rate1 up to l/min. 124 276 124 276
Operating Delivery head up to m wc 35 20 35 20
pressure: 6 bar 6 bar Viscosity up to mPas 1000 1000 1000 1000
infinitely varied Density: up to kg/dm³ 2.8 2.8 2.8 2.8
Order No. 0004-725 0004-735 Weight (kg) Motor + pump tube 4.3 4.3 4.3 4.3
1
The maximum flow rate is a value determined by means of a test bench and measured with water at a medium temperature of approx. 20°C. The measurement is carried out at Special voltages and
the pressure joint of the pump, without hose, nozzle or flow meter. The flow rate achievable in use is lower and depends on the individual application, the media properties and the frequencies on request.
configuration of the pump. The max. delivery head is also dependent on the pump design, motor and medium. Viscosity determined with oil.
46