Revision A (2021-03-05)

Contents

298006301
 Contents
1. Introduction......................................................................................................................................................... 3

2. Product Specifications..................................................................................................................................... 4

3. Safety for Router Table.....................................................................................................................................5

4. Assembly & Calibration....................................................................................................................................6

5. Operation..............................................................................................................................................................9

6. Maintenance...................................................................................................................................................... 10

1. 介绍..................................................................................................................................................................... 12

2. 产品规格............................................................................................................................................................. 13

3. 安全条例............................................................................................................................................................. 14

4. 安装与校准......................................................................................................................................................... 15

5. 操作..................................................................................................................................................................... 17

6. 保养..................................................................................................................................................................... 18

Exploded View and Parts List...............................................................................................................19

1
English Version

2
1. Introduction
Thank you for purchasing Harvey’s products. We All the graduations are laser etched on the scale.
believe you will be satisfied with the quality and The scale and flip stop provides accuracy and
repeatability for a wide variety of cutting tasks,
performance of our products.
such as machine stopped dados, mortises, fluting
The Model RF-36 needs to be used with The and other decorative profiles with precise stop
matching Router Table RT-685 or RT-800. points.

RF-36 featuring the unique Dual Fine-tuning  Premium Materials

Mechanism, an aerodynamically designed dust The Fence is made of anodized aircraft-grade
port, a flip stop and laser etched scale, this fence aluminum extrusion which is durable and provides
made of anodized aircraft-grade aluminum will great wear-resistance and superior hardness.
greatly improve your efficiency and expand your A MDF board is used for the Fence Face, which is
working capacity to a new notch. a perfect solution to providing tearout control and
additional support for your workpiece when using
large diameter cutters.
 Dual Fine-tuning Mechanism
a. Fine-tuning Mechanism of Fence Board
 Aerodynamically Designed Dust Port
The main fence is designed with a zero clearance
fine-tuning mechanism. The 2-1/2" (63.5mm) upper dust port on the fence
For metric version, the increment of a full turn of is aerodynamically designed, which can improve
the micro-adjustment knob is 1mm, and the your dust collecting efficiency.
increment for each turn of one grid in the scale
ring is 0.02mm; for imperial version, the increment  Toolless Adjustment
of a full turn of the micro-adjustment knob is 1/20”, Benefiting from its unique designs, all the
and the increment for each turn of one grid in the adjustments during operation are toolless, making
scale ring is 0.001”. your operation more convenient and efficient.
b. Fine-tuning Mechanism of Fence Face
The outfeed fence face can also be adjusted
separately with a Fine-tuning Mechanism.
Just like the mechanism on the main fence, for
metric version, the increment of a full turn of the
micro-adjustment knob is 1mm, and the
increment for each turn of one grid in the scale
ring is 0.02mm; for imperial version, the increment
of a full turn of the micro-adjustment knob is 1/20”,
and the increment for each turn of one grid in the
scale ring is 0.001”.
The router fence is available in metric and
imperial versions. Fig. 1

 Fence Face A. Fence Board

The fence faces can be tightened easily by B. Fence Face
locking knobs, and they are fixed by a dovetail C. Flip Stop
slot, so that you can move them to left or right for D. Guard
a desired opening size. E. Guide Rail
F. Scale
 Flip Stop and Scale
G. Fence Lock Handle
The Flip Stop slides in a groove on top of the
H. Fine-tuning Mechanism of Fence Face
fence and can be locked anywhere you choose.
Two flip stops are included. I. Dust Port
J. Fine-tuning Mechanism of Main Fence

3
2. Product Specifications
Fence Board Dimension：
---36" x 4-15/32" x 3-9/16" (915x113.5x91mm)
Fence Face Dimension:
---17-23/32" x 2-5/8" (450x66.675mm)
Max. Fence Assembly Travel：
---7" (177.8mm)
Fence Assembly Fine-tuning Itinerary：
---1/2" (12.7mm)
Fence Face Fine-tuning Itinerary：
---1/4" (6.35mm）
Dust Port Size：
---2-1/2" (63.5mm) outside
---2-1/4" (57.5mm) inside
Net Weight/Gross Weight：
---21.1 lbs (9.6kg) / 25 lbs (11.3kg)
Package Size：
---38" x10"x 7-3/8" (966x256x187mm)

Note:
The Model RF-36 is not a universal product,
needs to be used with the matching Router
Table RT-685 or RT-800.
The relevant dimensions of the Router Table is
shown in Fig.2.

Fig. 2

4
3. Safety for Router Table
This attachment works with the router, you 8. NEVER cut a workpiece without using a fence,
need to comply with the safety rules for using jig, or miter. Otherwise, the workpiece can be
universal electric tools and additionally pay grabbed by the cutter and pull your hands into the
special attention to the following safety cutter.
precautions：
9. NEVER use a workpiece shorter than six
1. To avoid making contact with the spinning inches without special fixtures or jigs. Otherwise,
cutter, never place hands directly over or in front the workpiece can become trapped between the
of the cutter. As one hand approaches the cutter, fence and cutter, which could draw your hands
move it away and over to the other side. Always into the spinning cutter.
keep hands at least 6" away from the spinning
cutter. 10. Keep any unused portion of the cutter below
the table surface to minimize the risk of making
2. Never operate the router table without first contact with the spinning cutter with your hands.
making sure that all lock levers and knobs are
tight, and that all fence hardware and guide rails 11. To prevent amputation or other injuries,
are secure. Otherwise, the workpiece can slip out always use a guard. Fabricate additional guards
of alignment while cutting and cause injury from or jigs for special circumstances. Use an
kickback. overhead guard if the fence is removed.

3. Never force materials past the router. Let the 12. To prevent tripping over the router power cord
cutter do the work. Excessive force is likely to when operating the table saw, always disconnect
result in poor cutting results and will cause it and safely store it out of the way.
kickback conditions that could cause serious
personal injury.

4. The danger of kickback and injury is increased

when the workpiece has knots, holes, or foreign
objects in it. Warped stock should be run through
a jointer before you run it through the router table.

5. Keep the cutter on the underside of the

workpiece when making blind cuts. This will
decrease the risk of accidental contact with the
cutter.

6. Always feed the workpiece against the rotation

direction of the cutter. Otherwise, the workpiece
could be aggressively pulled from your hands,
drawing them into the spinning cutter.

7. With the router disconnected from power,

rotate the router spindle to test any new setup to
ensure proper cutter clearance before starting the
router.

5
4. Assembly & Calibration
4.1 Unpacking
Check your product with Fig.3 and the exploded
view.
The RF-36 COMPASS Router Table Fence has
been completely assembled in factory. The guard
parts has been installed at the back of fence for
safe transportation, as shown in Fig.3.

Fig.5

b. As shown in Fig.6, install the fence on the

router table.
 During installation, align the T-bolt (B)
(Fig.5) with the holes (D) on the table
(Fig.6).
 Due to the differences between the table
dimensions, you may need to loosen the
set screws (E), (F), (G) and (H) for better
Fig.3 installation, after the fence is installed on
the table, pre-tighten the loosened
4.2 Install the guard fastener.
Remove the guard part from the back of fence,  After installation, move the fence to make
install the guard as shown in Fig.4. sure it is smooth. Do not tighten the fence
lock handle at this time.

Fig.4
Fig.6

4.3 Install the fence assembly on the router

4.4 Calibrate the guide rail
table
a. The following three adjustments need to be Note: The calibration of guide rail is essential
made before installation, as shown in Fig.5: to the accuracy of fence movement.
 Adjust the Scale (A) to “0”.
 Turn the T-bolt (B) out, the length of the A. As shown in Fig.7, loosen the fence face lock
unscrewed thread is about 10-12mm. The handle and remove the fence face.
straight edge of the head of the T-bolt should
be parallel to the guide rail.
 Adjust the lock bolt (C) until the straight edge
of the head of the lock bolt is parallel to the
guide rail, tighten it.

6
 D. Keep turning the screw (I) clockwise, tension
the bearings slowly and evenly until there is no
obvious waggle of the fence and the fence can be
moved when you just push at the end position, as
shown in Fig.10.

Fig.7

B. As shown in Fig.8, Turn the screws (I) (two on

each guide bar, a total of four) clockwise, tension
the bearings slowly and evenly until that all the Fig.10
bearings spin when you move the fence (the E. Re-install the fence face.
moving force should be put at the middle of the F. Check the parallelism of the fence face and the
fence). T-slot, as shown in Fig.11.
G. If any parallelism deviation exists, as shown in
Fig.12, loosen the screws (E) and (F), add a shim
of the same thickness as the deviation amount
at the position of guide rail bearing, push the
fence against the table mounting surface, and
tighten the screws (E) and (F). Repeat this step to
get the desired result.
Note:
If L1 > L2, add the shim at the corresponding
position of L1.
If L2 > L1, add the shim at the corresponding
position of L2.
The shim can be made of paper, copper sheet.
Fig.8

C. As shown in Fig.9, completely loosen the set

screws (E) and (F), move the fence to make the
guide bar against the mounting face of the router
table, tighten the set screws (E) and (F) in the
meantime.
Note: You can remove the Fence lock handle
to facilitate your adjustment.
If there is no mounting surface, you can
temporarily fix a plate on the rear side of the
table for better adjustment.
Fig.11

Fig.9 Fig.12

7
4.5 Re-position the fence Fine-tuning system.
Note: This step must be carried out after the
calibration of guide rail.
Due to the differences of table dimensions, the
fence Fine-tuning system need to be
re-positioned as the following steps:
a. As shown in Fig.13, loosen the screws (G), (H)
and (J).
b. As shown in Fig.13, rotate the lock nut (K)
counterclockwise about 3-4 turns, then turn the
lock nut (K) clockwise to tighten the fence
fine-tuning locating block.
c. After the fence fine-tuning locating block is
completely tightened, tighten the screw (H), then
lock the screws (G) and (J).

Fig.13

By now, the installation and calibration of your

fence has been completed, and it is ready for
use.

8
 two locking handles evenly, you can move or
5. Operation remove the fence face.
5.1 Moving, fine-tuning and locking the fence The outfeed fence face can be micro-adjusted
To move the fence, loosen the lock nut (K) and separately. As shown in Fig.15, turning the
fence lock handle. fin-tuning knob clockwise or counterclockwise can
To fine-tune the fence, loosen the fence lock move the outfeed fence face backward or
handle, tighten the lock nut (K). Turning the forward.
fine-tuning knob clockwise can move the fence Turn the fine-tuning knob and the scale ring will
forward; turning the fine-tuning knob rotate accordingly. The increment of a full turn of
counterclockwise can move the fence backward. the fine-tuning knob is 1/20”, and the increment
Turn the fine-tuning knob and the scale ring will for each turn of one grid in the scale ring is 0.001”.
rotate accordingly. The increment of a full turn of The scale ring is not stationary and can be set to
the fine-tuning knob is 1/20”, and the increment zero at any time.
for each turn of one grid in the scale ring is 0.001”. Note:
The scale ring is not stationary and can be set to The scale shown on the fence face dovetail
zero at any time. seat is used to read the scale of relative
Note: position, not absolute scale.
Before fine-tuning, be sure to loosen the fence Rotating the fine-tuning knob clockwise or
lock handle. counter-clockwise will produce extremely
The scale shown on the fence dovetail seat is small deviation. Pre-rotating the fine-tuning
used to read the scale of relative position, not handle along the adjustment direction can
absolute scale. effectively eliminate the error and obtain a
Turning the fine-tuning knob can move the very high adjustment accuracy.
whole fence. If the guide rail is not calibrated
correctly, the deflection will occur during
fence movement.
Rotating the fine-tuning knob clockwise or
counter-clockwise will produce extremely
small deviation. Pre-rotating the fine-tuning
handle along the adjustment direction can
effectively eliminate the error and obtain a
very high adjustment accuracy.

Fig.15
This fence face is made of MDF board which
features the standard dovetail slot. Referring
to the dimension shown in Fig.16, you can
also customize your fence face as desired.

Fig.14

5.2 Moving, fine-tuning and locking the fence

face
This product is equipped with two fence faces in
front and rear, each fence face can be locked by
two lock handles, as shown in Fig. 15. Unlock the Fig.16

9
5.3 Guard (Fig.17)
By loosening the guard lock knob, the guard can
6. Maintenance
be moved up and down or left and right. The RF-36 COMPASS Router Table Fence does
not need any special maintenance, as long as the
daily inspection, to avoid the occurrence of safety
accidents. Regular cleaning can maintain the
accuracy and improve the service life.

Daily inspect that:

 If the fence lock handle can effectively lock
the fence.
 If the fence face can be locked effectively.
 If the guard is damaged and can be locked
Fig.17 effectively.
5.4 Flip stop and scale  If the fence can be moved smoothly.
 If any other conditions that could hamper the
Loosen the flip stop lock knob to move the flip
safe operation of this router table fence exist.
stop left and right. When flip stop is not required, it
can be flipped over, as shown in Figure 18.
Cleaning & Protecting
Press the scale to move it for calibrating the
Frequently blow-off sawdust with compressed air
position.
and wipe away the remaining dust with a clean
shop rag, especially for the bottom of fence, the
guide rail and the fine-tuning parts. This is
important for the using safety and fine-tuning
accuracy of the router table fence.

Fig.18

5.5 Using the dust port

The dimension of dust port is shown in Fig. 19.
According to this size, you can mount suitable
dust hose, fastener or adapter.

Fig.19

10
中文版本

11
1. 介绍
感谢您购买海威公司产品，我们相信您会对产品质
量及性能感到满意。
RF-36 电木铣靠山不是一个通用产品，必须配合海
威电木铣工作台进行使用，匹配型号：RT-685、RT-800。
RF-36 电木铣工作台豪华靠山主要有靠山及靠山面
板双微调机制，空气动力学设计的集尘口，翻转限位和
激光镭雕的刻度尺四大功能。整身由航空级铝合金制成，
通过阳极氧化处理。无论视觉性还是功能性都有显著地
提升。

图1
 双微调机构
a. 主靠山微调机构
主靠山设计了零间隙微调机构。 A. 靠山主体
公制版本，微调旋钮每转动一圈的增量为 1mm，刻 B. 靠山面板
度环上一格的增量为 0.02mm;对于英制版本，微调旋钮 C. 限位挡块
每转动一圈的增量为 1/20”，刻度环上一格的增量为 D. 护罩
0.001”。
E. 导轨
b. 靠山面板微调机构
出料面板可以通过微调机构单独调整。 F. 刻度尺
公制版本，微调旋钮每转动一圈的增量为 1mm，刻 G. 靠山锁紧把手
度环上一格的增量为 0.02mm;对于英制版本，微调旋钮 H. 靠山面板微调旋钮
每转动一圈的增量为 1/20”，刻度环上一格的增量为 I. 集尘口
0.001”。
J. 靠山微调旋钮
 靠山面板
靠山面板通过燕尾槽进行固定，通过锁紧旋钮轻松
锁紧，您可以左右移动靠山获得想要的开口尺寸。

 刻度尺和限位挡块
限位挡块在靠山顶部的槽中滑动，可被固定在任意
所需位置。此豪华靠山标配两个限位挡块。
靠山顶部配备的刻度尺采用激光镭雕工艺。
精密镭射的刻度尺和限位挡块提高了大范围锯切的
精准性和可重复性，比如开槽、制榫和其他精确度要求
较高的工件。

 靠山材质
靠山主体由航空级铝合金制成，经过阳极氧化处理，
耐磨性好，硬度高。
靠山面板由 MDF 板制成，为你的操作提供了锯切耗
材的控制，并且在使用大直径的铣刀时为你的工件提供
了额外的支撑。

 空气动力学设计的集尘口
配备基于空气动力学设计的 63.5mm 上集尘口，更好
地提升工作时的集尘效率。

 免工具调节
电木铣工作台豪华靠山的调节使用无需额外工具，
操作简单高效。

12
2. 产品规格
靠山尺寸：
---36" x 4-15/32" x 3-9/16"(915x113.5x91mm)
靠板尺寸：
---17-23/32" x 2-5/8"(450x66.675mm)
靠山最大移动行程：
---7" (177.8mm)
靠山微调行程：
---1/2" (12.7mm)
靠板微调行程：
---1/4" (6.35mm）
吸尘口尺寸：
---2-1/2" (63.5mm) 外径
---2-1/4" (57.5mm) 内径
净重/毛重：
---21.1 lbs (9.6kg) / 25 lbs (11.3kg)
包装尺寸：
---38" x10" x 7-3/8" (966x256x187mm)

注意：
RF-36 电木铣靠山不是一个通用产品，必须配合海
威电木铣工作台进行使用，匹配台板核心尺寸如图 2 所
示.
匹配型号：RT-685
RT-800

图2

13
 12. 为了防止在操作台锯时，被电木铣的电源线绊倒，
3. 安全条例 务必在不使用电木铣时，将电木铣断开电源并收拾好电
本附件配合电木铣使用，除了必须遵守通用电动工 源线。
具的安全事项外（参考台锯说明书），还须遵循以下安
全事项： 警告：
和所有的设备一样，操作此工具也存在潜在危险。
1. 为了避免与正在旋转的铣刀发生接触，切勿将手部直 事故通常是由于对工具不熟悉或者注意力不集中造成
接置于铣刀的上方或前方。操作时，当一只手接近铣刀 的。使用此工具时应保持警惕，以减少发生人身伤害的
时，应立刻将手移到另一侧。手部与旋转的铣刀之间必 风险。如果操作时忽视安全措施，可能会发生严重的人
须要保持至少 150mm 的距离。 身伤害。

2. 在确保所有的锁紧杆和旋钮被锁紧、所有的靠山和导
轨被固定之后，再开始操作电木铣。否则在铣削时，工
件可能会滑出，从而引起木料回弹，对操作者造成人身
伤害。

3. 不要强行让木料穿过电木铣。让铣刀带动木料。过大
的外力很有可能导致较差的铣削效果，还会引起木料回
弹，造成严重的人身伤害。

4. 当工件上有结疤、孔洞或者异物时，会增加木料回弹
的风险和伤害。在用电木铣工作台加工弯曲的木料时，
应先将木料在平刨上进行加工。

5. 在进行盲切时，保持铣刀位于工件的下方，这样会减
小与铣刀发生意外接触的风险。

6. 工件的进料方向必须要和铣刀的旋转方向相反。否则
工件会从您手中被强行拉出，卷入旋转的铣刀中。

7. 进行新的设置后，须通过旋转电木铣主轴来检查铣刀
位置，以确保在启动电木铣前，铣刀间距合适（注意切
断电源）。

8.不要在没有使用靠山、夹具或者靠尺的情况下铣削木
料，否则工件可能会被铣刀拖拽，并将您的手拉入铣刀。

9. 在没有特制的夹具或装置时，不要铣削长度短于
150mm 的工件。否则工件可能会被夹在靠山和铣刀之间，
这可能会将您的手部卷入正在旋转的铣刀中。

10. 始终保持铣刀未使用的部分位于台面下方，以减小
手部与旋转的铣刀发生接触的风险。

11. 为了防止人身伤害，请务必使用护罩。对于一些特
殊情况，还应加装额外的护罩或者夹具。如果靠山被移
除，请使用上置式护罩。

14
4. 安装与校准 b. 如图 6 所示意，将电木铣靠山安装到电木铣台板上。
4.1 拆包
注意：
参考图 3 及爆炸图核对您的产品。
 安装时，注意将 T 型螺杆“B”(图 5）对准台板上
该产品在出运前已经完全组装好，用户无需组装；
的过孔“D”(图 6）。
出于运输目的，护罩部件固定在在靠山后侧，如图 3 所
 由于台板尺寸存在差异，为保证顺利安装，您可能
示。
需要先松开图 6 所示的紧固螺钉“E”、 “F”、
“G”、
“H”, 安置到台板上后再预紧松开的紧固件。
 安装完成后，前后移动靠山，确保靠山移动顺畅，
此时不要锁紧靠山锁紧把手。

图3

4.2 安装护罩
拆下护罩部件，如图 4 所示进行护罩的安装。

图6

4.4 校准导轨
注意：导轨的校准非常重要，如校准不好，靠山微调运
动过程中，容易产生偏摆。
a. 如图 7，松开靠山面板锁紧手柄，取出靠山面板。

图4

4.3 将靠山组件安装到电木铣工作台上
a. 在靠山安装到电木铣工作台之前，需完成以下三项调
整，如图 5 所示:
 图示刻度“A”调整到“0”。
 图示 T 型螺钉“B”旋出，旋出螺纹长度约 10-12mm,
图7
T 型螺钉头部直边与导杆平行。
b. 如图 8，顺时针旋转螺钉“I”（每个导杆上两个，共
 图示锁紧螺杆“C”头部直边调整到与导杆平行，
计 4 个），慢慢均匀张紧轴承，直到移动靠山时（移动
并锁紧。
靠山的着力点放在靠山中间），所有轴承均旋转为止。

图5
图8
15
c. 完全松开两边导轨的固定螺钉“E”& “F”，移动
靠山,使导轨导向轴承顶住电木铣台板安装面，如图 9 所
示，在顶住状态下，锁紧螺钉“E”& “F”。
注意：
拆下靠山锁紧把手，能方便您的调节。
如没有安装面，为保证调节顺利，可在台板后侧临
时固定一个挡板。

图 12

4.5 重新定位靠山微调装置

注意：该工序必须放在导轨校准工序后进行。

由于每个台板的加工尺寸存在误差，需要针对不同
图9
的台板，对靠山微调装置进行重新定位，操作步骤如下：
d. 继续顺时针旋转螺钉“I”，慢慢均匀张紧轴承，直到
a. 如图 13，松开螺钉“G”、“H”、“J”。
靠山无明显晃动，且可以在靠山一侧端面位置推动靠山，
b. 如图 13，逆时针旋转锁紧螺母“K”约 3-4 圈，然后
如图 10 所示。
顺时针旋转锁紧螺母“K”锁紧靠山微调定位块。
c. 在靠山微调定位块完全锁紧状态下，锁紧螺钉“H”，
然后锁紧螺钉“G”& “J”。

图 10

e. 重新安装靠山面板。
f. 如图 11 检查靠山面板与 T 型槽的平行度。
g. 如存在偏差，如图 12 所示松开螺钉“E”& “F”， 图 13
在导轨轴承处添加与偏差值等厚的垫片，将靠山顶向工
作台安装面，锁紧螺钉“E”& “F”；重复该步骤，直
到您满意为止。 到目前为止，您的靠山已经安装校准完成，可以进
注意：如 L1 大于 L2, 在 L1 对应导轨处添加垫片。 入使用状态。
如 L2 大于 L1, 在 L2 对应导轨处添加垫片。
垫片可采用纸片、铜皮等。

图 11
16
5. 操作
5.1 靠山的移动、微调与锁紧（图 14） 5.2 靠山面板的移动、微调与锁紧
该产品配备前后两个靠山面板，每个面板使用 2 个
锁紧把手进行固定，如图 15 所示，均匀松开锁紧把手，
松开锁紧螺母“K”及靠山锁紧把手，可以移动靠山。
可以移动或取出靠山面板。
松开靠山锁紧把手，锁紧锁紧螺母“K”，旋转微调
出料侧面板可以独立微调，如图 15 所示，旋转微调
把手，可以前后移动靠山，顺时针旋转，靠山后退，逆
旋钮，可以前后移动面板，顺时针旋转，面板后退，逆
时针旋转，靠山前进。
时针旋转，面板前进。
旋转微调旋钮，刻度环随动，每旋转一圈，运动 1mm,
旋转微调旋钮，刻度环随动，每旋转一圈，运动 1mm,
每格精度 0.02mm；刻度环为浮动的，可以随时校零。
每格精度 0.02mm；刻度环为浮动的，可以随时校零。
注意：
注意：
微调前，一定要松开靠山锁紧把手。
滑块上显示的刻度用于客户绝对位置的读取，显示
滑块支座上显示的刻度用于客户相对位置的读取，
“0”时，前后两个靠板共面，如存在偏差，调整刻度指
非绝对刻度。
针位置。
旋转微调旋钮，靠山整体移动，如果导轨未能有效
正反旋转微调旋钮，会产生极其微小的误差，顺着
校准，靠山运动过程中，会产生偏摆。
调节方向预旋转微调把手，可有效消除误差，获得极高
正反旋转微调旋钮，会产生极其微小的误差，顺着
的调整精度。
调节方向预旋转微调把手，可有效消除误差，获得极高
的调整精度。

图 15
图 14
注意：
该靠山系统靠山面板采用 MDF 板制作，面板上加工
有标准规格的燕尾槽，您可以根据需要，参考图 16 尺寸，
自行制作靠山面板。

图 16

17
5.3 护罩（图 17）
6. 维护
松开护罩锁紧旋钮，可以上下、左右移动护罩位置。
RF-36 产品无需特别的维护，只要做好日常检查，
避免安全事故的发生；定期清理，提高靠山精度的稳定、
提高靠山的使用寿命。

日常检查:
 靠山锁紧把手是否能有效锁紧靠山。
 靠山面板是否能被有效锁紧。
 护罩是否破损，是否能被有效锁紧。
 靠山移动是否顺畅，是否存在卡死现象。
 任何其他会导致本款电木铣靠山组件不能被安全使
用的情况。

图 17 清理和维护:
 经常用气枪吹掉木屑，特别是靠山底部、导轨及微
5.4 定位挡块 & 刻度尺 调部分，并用干净的抹布擦去灰尘。这对于靠山组
件使用的安全性及微调精度均存在重要的影响。
松开定位挡块锁紧旋钮，可以左右移动定位挡块，
在无需使用定位挡块的场景，可以将挡块翻转，如图 18
所示。
按压刻度尺，可以移动刻度尺，校准刻度尺的位置。

图 18

5.5 吸尘口的使用

靠山吸尘口尺寸如图 19 所示，根据该尺寸配置合适
的吸尘管、管扣或合适的接头。

图 19

18
Exploded View and Parts List

Router Table fence parts

19
 Router Table fence parts list

REF DESCRIPTION QTY REF DESCRIPTION QTY

201 Fence Board 1 239 Cap screw M6x16 4
202 Spring bearings 2 240 Cap screw M4x12 12
203 Scale 1 241 Adjusting washer 22x16x0.1mm 1
204 PVC paster 1x10x130 6 242 Fine-tuning nut 4
205 PVC paster 1x10x245 6 243 Pin 3x6 2
206 Fence Lock Handle Holder 2 244 Fence fine-tuning shaft 1
207 O-Ring 2.65x11.2 2 245 Fence face fine-tuning shaft 1
208 Fence Lock Handle 2 246 O-Ring 2.65x17 4
209 T-slot bolts M8x60 2 247 Pin 2x16 1
210 Guide Rail 2 248 Fence fine-tuning shaft seat 1
211 Shaft 8 249 Set collar 1
212 Bearing 628-4 8 250 Fence lock bolt 1
213 Button HD screw M6x16 4 251 Fence lock nut 1
214 Cap screw M5x16 4 252 Bearing 61900 3
215 Flat washer 5 4 253 Short head screw M4x8 10
216 Lock washer 5 4 254 Scale ring 2
217 Fence face Lock Handle Holder 2 255 Fine-tuning knob 2
218 / / 256 Lock nut M8X20 2
219 Fence face Lock Handle 4 257 Fence face fixed block 1
220 Set screw M6x45 4 258 Cap screw M6x30 5
221 Dovetail lock block 2 259 Set screw M6x25 4
222 Fence face 2 260 Fence face Lock Handle Holder 2
223 Flip stop 2 261 Pin 5x25 2
224 Square nut M6 14 262 Fence face seat 1
225 Set screw M6x30 4 263 Cap screw M4x20 6
226 Shoulder Bolt ∅ 5 x 4 4 264 Fence face dovetail seat 1
227 O-Ring 1.8x5 4 265 Fence face dovetail slipper 1
228 Nylon washer 4 4 266 Scale point 1
229 Flip stop bracket 2 267 Short head screw M3x8 1
230 Flip stop lock knob 2 268 Set screw M6x6 6
231 Dust port 1 269 Fence face fine-tuning shaft seat 1
232 Cap screw M5x12 2 270 L-type fixed block 2
233 Guard 1 271 Fence dovetail seat 1
234 Nylon washer 6 4 272 Fence dovetail slipper 1
235 Guard lock knob 2 273 Set screw wi M4x12 4
236 Guard block 2 274 Cap screw M4x35 4
237 End cover 1 275 Set screw M8x6 4
238 Fine-tuning nut seat 1 276 Cap screw M4x12 2

20
21