Esp32 Eco v3 User Guide En
Uploaded by
ieliuEsp32 Eco v3 User Guide En
Uploaded by
ieliuESP32 ECO V3
User Guide
Version 1.1
Espressif Systems
Copyright © 2020
www.espressif.com
About This Guide
This document describes differences between V3 and previous ESP32 silicon wafer
revisions.
Release Notes
Date Version Release notes
2020.01 V1.0 Initial release.
Added item 6 to Chapter 1 Design Changes in ECO
2020.07 V1.1
V3.
Documentation Change Notification
Espressif provides email notifications to keep customers updated on changes to
technical documentation. Please subscribe at https://www.espressif.com/en/subscribe.
Certification
Download certificates for Espressif products from https://www.espressif.com/en/
certificates.
Table of Contents
1. Design Change in ECO V3 .....................................................................................................1
2. Impact on Customer Projects ...............................................................................................2
2.1. Use Case 1: Hardware and Software Upgrade ..........................................................................2
2.2. Use Case 2: Hardware Upgrade Only ........................................................................................2
3. Label Specification ................................................................................................................3
4. Ordering Information .............................................................................................................4
1. Design Change in ECO V3
1. Design Change in ECO V3
Espressif has recently released one wafer-level change on ESP32 Series of products (ECO
V3). This document describes differences between V3 and previous ESP32 silicon wafer
revisions. Below are the main design changes in ECO V3 Series of chips:
1. PSRAM Cache Bug Fix: Fixed “When the CPU accesses the external SRAM in a certain
sequence, read & write errors can occur.”. Details of the issue can be found in item 3.9
in ESP32 ECO and Workarounds for Bugs.
2. Fixed “When each CPU reads certain different address spaces simultaneously, a read
error can occur.” Details of the issue can be found in item 3.10 in ESP32 ECO and
Workarounds for Bugs.
3. Optimized 32.768 KHz crystal oscillator stability, the issue was reported by client that
there is a low probability that under ECO V1 hardware, the 32.768 KHz crystal oscillator
couldn’t start properly.
4. Fixed Fault injection issues regarding secure boot and flash encryption are fixed.
Reference: Security Advisory concerning fault injection and eFuse protections
(CVE-2019-17391) & Espressif Security Advisory Concerning Fault Injection and Secure
Boot (CVE-2019-15894)
5. Improvement: Changed the minimum baud rate supported by the CAN module from 25
kHz to 12.5 kHz.
6. Allowed Download Boot mode to be permanently disabled by programming new eFuse
bit UART_DOWNLOAD_DIS. When this bit is programmed to 1, Download Boot mode
cannot be used and booting will fail if the strapping pins are set for this mode. Software
program this bit by writing to bit 27 of EFUSE_BLK0_WDATA0_REG, and read this bit by
reading bit 27 of EFUSE_BLK0_RDATA0_REG. Write disable for this bit is shared with
write disable for the flash_crypt_cnt eFuse field.
1/5
Espressif Submit Documentation Feedback 2020.07
2. Impact on Customer Projects
2. Impact on Customer Projects
This section is intended to help our customers to understand the impact of using ECO V3
in a new design or replacing older version SoC with ECO V3 in existing design.
2.1. Use Case 1: Hardware and Software Upgrade
This is the use-case where the new project is being initiated or upgrade for hardware and
software in an existing project is a possible option. In such a case, the project can benefit
from protection against fault injection attack and can also take advantage of newer secure
boot mechanism and PSRAM cache bug fix with slightly enhanced PSRAM performance.
1. Hardware Design Changes:
Please follow the latest Espressif Hardware Design Guideline. For 32.768 KHz crystal
oscillator stability issue optimization, please refer to Section Crystal Oscillator for more
information.
2. Software Design Changes:
1) Select Minimum configuration to Rev3: Go to menuconfig > Conponent config >
ESP32-specific, and set the Minimum Supported ESP32 Revision option to “Rev
3”.
2) Software version: Recommend to use RSA-based secure boot from IDF4.1 and
later. IDF3.X Release version can also work with application with original secure boot
V1.
2.2. Use Case 2: Hardware Upgrade Only
This is the use-case where customers have existing project which can allow hardware
upgrade but software needs to remain the same across hardware revisions. In this case the
project gets benefit of security to fault injection attacks, PSRAM cache bug fix and
32.768KHz crystal oscillator stability issue. The PSRAM performance continues to remain
the same though.
1. Hardware Design Changes:
Please follow latest Espressif Hardware Design Guideline.
2. Software Design Changes:
Client can continue to use the same software and binary for deployed product. The
same application binary will work on both ECO V1 and V3 chip versions.
2/5
Espressif Submit Documentation Feedback 2020.07
3. Label Specification
3. Label Specification
The label of ESP32-D0WD-V3 is shown below:
The label of ESP32-D0WDQ6-V3 is shown below:
3/5
Espressif Submit Documentation Feedback 2020.07
4. Ordering Information
4. Ordering Information
For product ordering, please refer to: Espressif Products Ordering Information.
4/5
Espressif Submit Documentation Feedback 2020.07
Disclaimer and Copyright Notice
Information in this document, including URL references, is subject to change without
notice.
THIS DOCUMENT IS PROVIDED AS IS WITH NO WARRANTIES WHATSOEVER,
INCLUDING ANY WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS
FOR ANY PARTICULAR PURPOSE, OR ANY WARRANTY OTHERWISE ARISING OUT
OF ANY PROPOSAL, SPECIFICATION OR SAMPLE.
All liability, including liability for infringement of any proprietary rights, relating to use of
information in this document is disclaimed. No licenses express or implied, by estoppel or
otherwise, to any intellectual property rights are granted herein.
The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is
a registered trademark of Bluetooth SIG.
All trade names, trademarks and registered trademarks mentioned in this document are
Espressif IoT Team property of their respective owners, and are hereby acknowledged.
www.espressif.com Copyright © 2020 Espressif Inc. All rights reserved.
