Electronics & Software

SCP Slim for engine indication Type 2852B..., 4665B1,

5064E1..., 5271Y51
Signal conditioning system, with optional PiezoSmart

The 'Signal Conditioning Platform' SCP Slim Type 2852B... is a

modular system for the conditioning of a wide range of diffe-
rent measuring signals, such as signals from piezoelectric and
piezoresistive pressure sensors. It is specifically well suited for
combustion pressure measurements on engine test beds and
in-vehicle applications.

The key features for SCP Slim are: SCP Slim Type 2852B11 for 2 measuring modules
• Modular design for maximum flexibility (up to 16 channels)
• Ethernet interface
• Remote controlled via PC
• Power supply with voltage range from 100 … 240 VAC and
10 … 36 VDC
• Improved Graphical User Interface (GUI)
- Table overview with all amplifier and sensor relevant data
- Parameters selectable (editing & copying) in table.
- Via Ethernet easy export function of amplifier settings and
TEDS data
- Histogram of pmax distribution including working cycles
• Signal compatible with all combustion analyzers SCP Slim 19"tray consisting of 2 SCP Slim Type 2852B11 and 2852B01
• PiezoSmart sensor identification for increased process relia- mounted on support plate Type 5746A12 for 4 measuring modules
bility and improved data quality

Description
The SCP Slim consists of a base unit and functionspecific
measuring modules. For combustion pressure measurements
and combustion analysis on engines, a wide range of different
and interchangeable measuring modules for frontend signal
conditioning is available.
If the automatic sensor identification PiezoSmart is used, all
relevant data of an individual sensor are stored on a TEDS
(Transducer Electronic Data Sheet) and are available for auto-
matic setting of parameters and adjustments.
Process reliability of test procedures and quality of measure-
ment data are significantly improved by simultaneously sim-
plifying test bed setup and test preparations.
2852B_003-204e-03.23

SCP Slim consisting of Base-Chassis Type 2852B11 and expansion ­chassis.

Application Type 2852B01 for 8 measuring modules, with optional chassis legs Type
5746A3
With the function-specific modules, measuring tasks within
combustion pressure and gas exchange, as well as injection
pressure and general pressure measurements are efficiently Software interfaces for
accomplished. • FEVIS
• OSIRIS
Due to the small dimensions and low voltage power supply, • A&D CAS
SCP Slim is well suited for in-vehicle testing. • ONO SOKKI DS-2000
• DEWETRON

Seite 1/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Measure modules for SCP Slim

• Charge amplifier without sensor identification Type 5064E11
• Charge amplifier with sensor identification Type 5064E12 and 5064E13
• Piezoresistive amplifier with sensor identification Type 4665B1
• Bridge amplifier Type 5271Y51

Type 5064E11 Type 5064E12 Type 5064E13 Type 4665B1 Type 5271Y51

Configuration possibilities of SCP Slim

SCP Slim Type 2852B11 S CP Slim Type 2852B11, with optional chassis legs
Type 5746A3
2852B_003-204e-03.23

SCP Slim 19" tray consisting of 2 SCP Slim Type 2852B11 and 2852B01 SCP Slim consisting of base chassis Type 2852B11 and expansion chassis
mounted on support plate Type 5746A12 for 4 measuring modules Type 2852B01 with optional chassis legs Type 5746A3

Page 2/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Technical data SCP Slim Type 2852B...

Chassis Digital I/O

Module cards max. 2 Digital I/O Trigger / Operate
Channels per rack 4 – Trigger via optocoupler
With rack combination max. 16 on analog output
Power supply guided connection
Standard (single module) VDC 10 ... 36 High V 3 ... 30
Standard (cascading up to Low V <2
4 modules) 11 ... 36 Current input High mA 2 ... 29
With external power supply VAC 100 ... 240, ±10 % Pull-up on +24 V (connectable) kΩ 10
Power consumption max. W 20 Pull-down on DGND (connectable) kΩ 1
Inrush current (Main with 3 Ex- A ≈13 Connection Type D-Sub 9 pin neg.
tensions)
Degree of protection IP 40 Digital output DOUTA1 ... B4 – isolated solid with
Fuse 8A slow-blow (SPT) PhotoMos relay
Operating temperature range1) °C 0 ... 50 Current load (continuous) mA <100
Min. / max. temperature range1) °C –40/50 Voltage (continuous) V <±42
Dimensions Type 2852B01 Voltage for external devices V 24
Hight HE (mm) 1 (41) Current draw max. mA 50
Width mm 220 Connection Type D-Sub 15 pin neg.
Depth mm 230
Weight kg ≈1.6
Software Graphical User Interface (GUI)
COM components for Microsoft
Windows 10, 11

1)
non condensing

Connections on rear side

Analog output/interface (integrated)

Analog outputs 4
Voltage V 0 ... ±10
Current (per channel) mA 0 ... ±2
Error % <±0.1
Trigger output (optocouplers)
High V >2.4
Low V <0,8
Pull-up on +5 V RS kΩ 10
Connection Type D-Sub 37 pin neg.
2852B_003-204e-03.23

Communication interface
Interface Type RS-232C
Connection Type D-Sub 9 pin neg.
Interface Type Ethernet
Connection Type RJ-45

CAN bus interface

Number 1
Max. transmission rate 1 Mbit/s max.

Page 3/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Technical data valid for all modules LEDs on the module indicate the following operating condi-
All values for setting the parameters are stored in a nonvolatile tions:
data memory and are automatically loaded on initial startup. • Exceeding the overload threshold
Operating the system and setting the parameters are perfor- • Drift compensation with cycle detection (Drco/short,
med exclusively with a PC via GUI or with a host computer. Drco/long)
• Measure/reset
Operating temperature range1) °C 0 ... 60
Min./max. temperature °C –40/60 The amplifier has separated input grounds of channel A and
Vibration resistance (20 ... 2 000 Hz, gp 10 channel B in order to prevents signal interference. A differen-
duration 16 min, cycle 2 min) tial amplifier stage prevent ground loops between any input
Shock resistance (1 ms) g 200 ground and the output ground.
Sound resistance dBA 120
Degree of protection (EN 60529) IP 40
Front panel dimensions mm 106.5x35.0
TE 7
1)
non condensing

Charge amplifier Types 5064E11, 5064E12, 5064E13

The amplifier modules Types 5064E11, 5064E12, 5064E13
are microprocessor controlled 2-channel charge amplifiers Type 5064E12
with analog signal conditioning. The Types 5064E12, 5064E13
include the function for automated sensor identification
(PiezoSmart).
These amplifiers enable the recording of sensor operating
hours and pressure cycles when using PiezoSmart sensors. In Technical data
addition they have the ability to determine when a cylinder Charge amplifier Type 5064E1...
pressure sensor is exposed to extreme operating conditions. Number of channels 2
Important information such as sensor operation hours, pressure Measuring range pC ±100 ... 100 000
cycles and pMax can be calculated and automatically saved to Error (0 ... 60 °C) % <±0.5
the TEDS chips (Transduer Electronic Data Sheet) located in the typical (25 °C) % ±0.1
sensor connector. The recorded pMax-values are classified in 6 Measuring models Short, Long, Drco*/Short, Drco*/Long
different pressure ranges, (<100 bar/<150 bar/<200 bar/<250 Drift 'Long'
bar/<300 bar/≥300 bar) which give a clear indication of the at 0 ... 60 °C pC/s <±0.2
sensor load profile during the application. at 25 °C pC/s <±0.05
typical pC/s <±0.03
A further feature is the cyclic detection of the pMax values, the Reset-operate transition pC <±1.5
output of which is a digital signal via the CAN bus interface Time constant ('Long') s >100 000
(CAN2) of the SCP. In addition, the pMax values are output as Drift compensation 1/min ≈100 ... 20 000
an analog signal via the analog outputs (C and D). Output voltage V 0 ... ±10
Output current mA 0 ... ±2
The pMax detection range corresponds to the double pressure Output impedance Ω 10
2852B_003-204e-03.23

range of ±2FS. The scaling of the detection range is adjustable Zero point error (reset) mV <±5
Output noise (0,1 Hz ... 1 MHz) mVpp <8
between ±2FS and ±1FS. (Type 5064D has a fix scaling of
typical mVpp <4
±1FS)
Frequency range (20 Vpp, –3 dB) kHz ≈0 ... >200
Group delay time µs <3
Along with the input of the sensor-specific data, the paramete-
Low-pass filter (Butterworth, 2nd order, kHz 0,3/1/3/5/10/
rization allows the selection of different low-pass filters as well
selectable, –3 dB) 30/50/100/off
as a –8 V offset with simultaneous amplification of the signal
'Overload' threshold V ≈±11
by a factor of 1,8 for a better utilization of analogue inputs
Offset adjustable (gain 1,8) V –8.0 ±0.04
with –8 ... 10 V.
Crosstalk attenuation chan. A, chan. B dB >60

Page 4/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Technical data (continuation) Technical data

pMax function Piezoresistive amplifier Type 4665B1
pMax detection range Number of channels – 2
(adjustable scaling) FS ±1/±2 Gain – 10 ... 270
pMax output (digital) - CAN bus Additional gain – 1 ... 10 (in 0.1)
Frequency range kHz 3/5/10/30/50/100 Error (0 ... 60 °C) % <±0.3
Resolution bit 12 typical (25 °C)
pMax output (analog) - channel C & D Group deleay (Input-Output) µs <5
Frequency range kHz 3/5/10/30/50/100 Output voltage V 0 ... ±10
Recording on TEDS Output current mA 0 ... ±2
Frequency range kHz 0 ... ≈100 Output impedance Ω 10
Speed range (4 clock engine) 1/min 100 ... 20 000 Zero point adjustment range
Errors absolute %FS ±2 referred to input mV –100 ... 500
Power supply (module) - via SCP Output interference signal
Weight kg ≈0.42 (0,1 Hz...1 MHz) amp. ≤100 filter off mVpp
(0,1 Hz...1 MHz) amp. ≤100 filter 30 kHz mVpp
Connections Type (0,1 Hz...1 MHz) amp. ≤270 filter off mVpp
Signal inputs 5064E11 BNC neg. (0,1 Hz...1 MHz) amp. ≤270 filter 30 kHz mVpp
5064E12* TRIAX pos. Frequency range (20 Vpp, –3 dB) kHz 0 ... >90
5064E13* Fischer TRIAX up to amplifier 10 ... 270 kHz
pos. Low-pass filter (Butterworth, 2nd order, Hz 10,30,100,300
Signal outputs BNC neg. selectable, –3 dB) kHz 2,3,10,30
Actuation, outputs, supply 64 pin DIN41612 Linearity adjustment, second power % –3 ... 3 (in 0.1)
* with automated sensor identification PiezoSmart 'Overload' threshold V ≈±11
Temperature output analog
Piezoresistive amplifier Type 4665B1 Sensitivity mV/°C 10
The measuring module Type 4665B1 is a microprocessor- Frequency Hz 1
controlled 2-channel amplifier for piezoresistive sensors with Max. error °C ±2.5
analog signal conditioning. The amplifier is particularly recom- Temperature output digital
mended for high-accuracy measurements with temperature Temperature output – CAN bus
digital compensated and analog compensated sensors. Frequency range kHz 0 ... ≈ 5
Resolution bit 12
Additional zero point shift V –8 or –10
• Automatic sensor identification PiezoSmart Power supply (module) – via SCP
• Compatible with all piezoresisitve pressure sensors from Kistler Weight kg 0.32
• Analog signal output for pressure and temperature
• Digital signal output for temperature via CAN-BUS Sensor
• Support of digital temperature compensation for maximum Sensor supply (I ref) mA 1 or 4
measuring accuracy Maximum load (I ref: 4 mA) kΩ 5
• Simple absolute pressure adjustment Maximum load (I ref: 1 mA) kΩ 20
• Recording of working time synchron with charge amplifier
Type 5064E1... or via trigger signal Interface, sensor detection
Connection according to IEEE 1451.4 – –
2852B_003-204e-03.23

This measuring module is used for signal amplification of pie- Max. length for extension cable m 10
zoresistive pressure sensors and is used typically for measuring Temp. range for PiezoSmart-coupling °C –20 ... 85
injection pressure or hydraulic oil pressure as well as the pres-
sures in the inlet/exhaust of combustion engines. Connections
Signal inputs Type 103 (Fischer, 5 pin)
Signal outputs Type BNC neg.
Actuation, outputs, supply Type 64 pin DIN41612
Signal inputs and outputs (trigger for wor- Type D-Sub 9 pin neg.
king time recording, temperature)

Page 5/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Bridge amplifier Type 5271Y51 Low-pass filter (2nd order, Hz 10/30/100/300

This 2-channel bridge amplifier has two differential inputs and selectable/Butterworth, –3 dB) kHz 1/3/10/30/100
is designed for bridge sensors and especially for strain gauge
sensors. Sensor excitation (bridge voltage)
Sensor excitation voltage V 1,0 ... 12,0
The amplifier provides an adjustable and stabilized voltage Voltage error (>2,5 V) % <±0,1
supply for piezoresistive sensors. High bandwidth electronics Output current mA <50
with selectable filters ensure that the Type 5271Y51 can be
utilized in a wide range of applications Bridge completion (amplifier internal)
Half-bridge (completion) Ω 10 000
Quarter-bridge (completion) Ω 120/350/1 000

Sensor bridge resistance

Sensor excitation =1V Ω 20 ... 10 000
= 2.5 V Ω 50 ... 10 000
=5V Ω 100 ... 10 000
= 10 V Ω 200 ... 10 000

Sensor sensivity
Sensor excitation =1V Ω 2 ... 2 000
Type 5271Y51 = 2.5 V Ω 0.8 ... 800
=5V Ω 0.4 ... 400
Product features = 10 V Ω 0.2 ... 200
• For universal applications for strain gage sensors and Output signals
piezoresistive sensors with voltage excitation Output voltage (short circuit proof) V 0 ... ±10
• Variable bridge excitation 1 Sense
Sense +
... 12+
Volt Rcal/shunt
Output current mA 0 ... ±5
Speisung + Speisung +
• Voltage amplifier (with variable gain up to 5 000)Signal + Output impedance Ω 10
• AutomatedSignal +
Signal -
zero adjustment Signal
(tare)
+ Output noise signal
• Prepared for automatic sensor identification (0.1 Hz ... 1 MHz)
(PiezoSmart)
Speisung - Speisung - Speisung - Gain <100 mVpp <15
Sense - Sense - Sense -
Gain <1 000 mVpp <40
The bridge amplifier Type 5271Y51 is suitable for the following Gain ≥1 000 mVpp <180
connections: Frequency range kHz 0 ... >120
(20 Vpp, –3 dB)
Sense + Sense + Rcal/shunt

Excitation + Excitation +
Power supply (module) – via SCP
Signal + Weight kg ≈0.4
Signal +
Signal - Signal +

Connections
Excitation - Excitation - Excitation - Voltage output Type BNC neg.
Sense - Sense - Sense -
Sensor input Type D89 female
4-wire-/6-wire-full-bridge Half-bridge Quarter bridge Actuation, outputs, supply Type 64 pin DIN41612
2852B_003-204e-03.23

Technical data (continuation) Optional accessories Type/Art. No.

• D-Sub connector 9 pin pos. with
Number of channels – 2 soldered connection 7.640.048
Input voltage range (differential) V 0 ... ±10 • Extension cable D-Sub 9 pin pos.
Gain – 0.5 ... 5 000 with open ends, L = 5 m 5.590.183
Input resistance MΩ >100 • D-Sub connector 9 pin pos. with
Gain error (0 ... 60 °C) % <±0.2 screw connection 5.510.337
typical (25 °C) % ±0.05
Zero point error % <10 mV
Linearity error % <±0.01
Zero adjustment (tare) % 0 ... ±100
Page 6/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Dimensions
Front View
Example with measuring modules (not included)
Charge Amplifier Charge Amplifier
Type 5064C Type 5064C

Analog Out Sensor Analog Out Sensor

Measure A B A B Measure A B A B
B B
A A
Error Drco Error Drco

Slot 1 Slot 2
Front View

Rubber pads self-adhesive

(included accessories)
Slot 1 Slot 2

Fuse 8A
Type SPT
5x20

M4

75 ±0,1
75 ±0,1
22,5 ±0,1

1 2

219 40,95

Cascading for SCP Slim

Rear View
System Expansion up to 4 Units, 8-Slot, 16-Channels

Error Master

Power 10...36V
Analog Output Digital I/O In
Main Chassis
Type 2852B11
3
-
2
+
CAN Ethernet RS-232C
Expansion
Out to Expansion Type 2852B12
4 1

Error Master
2852B_003-204e-03.23

Power 1 Master In
Out to Expansion

Expansion Chassis 1
Expansion 1 In
Out to Expansion
Expansion 2 In In
Out to Expansion Expansion

Type 2852B01
Expansion 3 In
Out to Expansion

Out to Expansion

Error Master

Expansion Chassis 2
Power 1 Master In
Out to Expansion
Expansion 1 In

Type 2852B01
Out to Expansion
Expansion 2 In In
Out to Expansion Expansion
Expansion 3 In
Out to Expansion

Out to Expansion

Error Master

Power 1 Master In

Expansion Chassis 3
Out to Expansion
Expansion 1 In
Out to Expansion
Expansion 2 In In

Type 2852B01
Out to Expansion Expansion
Expansion 3 In
Out to Expansion

Out to Expansion

Page 7/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Expansion facilities for the SCP Slim for the 19" module

19" mounting kit for 1 SCP Slim, Type 5746A10

19" mounting kit consisting of 2

brackets for mounting an SCP Slim
Type 2852B... in a 19" rack.

19" mounting kit for 1 and 2 SCP Slim, Type 5746A11

19" mounting kit consisting of

1 empty case and 2 brackets
for mounting an SCP Slim Type
2852B... in a 19" rack. This kit in-
cludes a base plate which can be
used for mounting a second SCP
Slim in a 19" rack.

19" mounting kit for 2 SCP Slim, Type 5746A12

19" mounting kit consisting

of 2 brackets and 1 base plate
for mounting 2 SCP Slim Type
2852B... in a 19" rack.

öffentlich

2xSCP-Slim 1xSCP-Slim

Connecting plates set for 2 x SCP Slim, Type 5746A8

75

Mounting kit consisting of 2 con- M4x8

230

380

necting plates for compact moun-

ting of 2 x 2852B...
61
75
2852B_003-204e-03.23

6 55,23 öffentlich 6
Das Urheberrecht an dieser Zeichnung, die dem Empfänger

Ohne unsere schriftliche Genehmigung darf die Zeichnung

231 83,23
weder kopiert noch vervielfältigt, noch an Drittpersonen
persönlich anvertraut wird, verbleibt unserer Firma.

mitgeteilt oder zugänglich gemacht werden.

öffentlich Erstmals verwendet Werkstoff

5746A...
Änderung Datum Ersatz für Erste Proj.-Nr. Massstab Kopie Datum
100013383 17.10.2016 1:2 17.10.2016

Tragegriff-Set für SCP-Slim (_HE)

Das Urheberrecht an dieser Zeichnung, die dem Empfänger

Massbild

Connecting plates set for 1 x SCP Slim, Type 5746A7

Ohne unsere schriftliche Genehmigung darf die Zeichnung

2xSCP-Slim 1xSCP-Slim
weder kopiert noch vervielfältigt, noch an Drittpersonen

gez. 16.09.2016 Bsi Material-Nr.

siehe Tabelle
75

75

gepr. 17.10.2016 Wsa

persönlich anvertraut wird, verbleibt unserer Firma.

Bl. Zeichnungs-Nr. Ver.

ges. 17.10.2016 Bsi measure. analyze. innovate. A3 2/2 100.263.506 a
KIWAG-SWX_A3q
mitgeteilt oder zugänglich gemacht werden.

100.263.506 - a - skbvdg - SKB VDok Grafik - öffentlich - Freigegeben --- siehe Tabelle --- 08-Aug-2017 14:00 (CET) - [email protected]
Erstmals verwendet
5746A...
Änderung Datu
100013383 17.

Mounting kit consisting of 2 con- M4x8 M4x8

gez.
Tragegriff-
Massbild
16.09.2016 Bsi

necting plates for compact moun- 17.10.2016 Wsa

230

380

230

380

gepr.

ges. 17.10.2016 Bsi

KIWAG-SWX_A3q
100.263.506 - a

ting of 1 x 2852B...
62,5
61
75

75

6 55,23 6 23,95
Das Urheberrecht an dieser Zeichnung, die dem Empfänger

Ohne unsere schriftliche Genehmigung darf die Zeichnung

231 83,23 231 40,95

weder kopiert noch vervielfältigt, noch an Drittpersonen
persönlich anvertraut wird, verbleibt unserer Firma.

mitgeteilt oder zugänglich gemacht werden.

Erstmals verwendet Werkstoff

5746A...
Änderung Datum Ersatz für Erste Proj.-Nr. Massstab Kopie Datum
100013383 17.10.2016 1:2 17.10.2016

Tragegriff-Set für SCP-Slim (_HE) Page 8/9

Das Urheberrecht an dieser Zeichnung, die dem Empfänger

Massbild
Ohne unsere schriftliche Genehmigung darf die Zeichnung
weder kopiert noch vervielfältigt, noch an Drittpersonen

gez. 16.09.2016 Bsi Material-Nr.

siehe Tabelle
gepr. 17.10.2016 Wsa

This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
persönlich anvertraut wird, verbleibt unserer Firma.

Bl. Zeichnungs-Nr. Ver.

ges. 17.10.2016 Bsi measure. analyze. innovate. A3 2/2 100.263.506 a
KIWAG-SWX_A3q
mitgeteilt oder zugänglich gemacht werden.

100.263.506 - a - skbvdg - SKB VDok Grafik - öffentlich - Freigegeben --- siehe Tabelle --- 08-Aug-2017 14:00 (CET) - [email protected]
Erstmals verwendet Werkstoff
5746A...

the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are Änderung
100013383
Datum
17.10.2016
Ersatz für Erste Proj.-Nr. Massstab
1:3
Kopie Datum
17.10.2016

from the use of Kistler products is excluded. protected by various intellectual property rights. For more details
Tragegriff-Set visit www.kistler.com.
für SCP-Slim (_HE)
Massbild
gez. 16.09.2016 Bsi Material-Nr.
siehe Tabelle
gepr. 17.10.2016 Wsa Zeichnungs-Nr.
Bl. Ver.
ges. 17.10.2016 Bsi measure. analyze. innovate. A3 1/2 100.263.506 a
KIWAG-SWX_A3q
100.263.506 - a - skbvdg - SKB VDok Grafik - öffentlich - Freigegeben --- siehe Tabelle --- 08-Aug-2017 14:00 (CET) - [email protected]
 SCP Slim for engine indication – Signal conditioning system, with optional PiezoSmart,
Type 2852B..., 4665B1, 5064E1..., 5271Y51

Included accessories Type/Art. No. Optional accessories Type/Art. No.

for SCP Slim
• Power cable on request • Power supply (AC adapter) 5781A1
• Ethernet cable to conect SCP and PC/ 65010017 90 ... 260 VAC/50 ... 60 Hz
Host (not included with extension rack • Null modem cable to connect SCP and 1200A27
Type 2852B01) PC/Host via RS-232C
• Power supply (AC Adapter) 5781A1 • USB/RS-232C adapter 2867
90 ... 260 VAC/­­­50 ... 60 Hz, only for Type • TEDS editor for PC 2839A-01-003
2852B12 • D-Sub connector 37 pin (pos.) 7.640.062
• Expansion-kit for cascading SCP Slim (cas- 5746A4 • Remote switch (measure/reset) connec- Z20979
cading cable l = 0,4 m), cover plate for table to digital I/O interface
plugs including mounting material, only for • Remote switch, L = 2.0 m Z20979-10
Type 2852B01 (measure/reset) connectable to digital
• 4 rubber pads self-adhesive for SCP Slim 5.211.238 I/O interface
chassis
• Connector for DC power supply, ­only for 5.511.384
Type 2852B11
Order form with ordering code
Optional accessories Type/Art. No
for SCP Slim SCP Slim chassis (without modules) Type 2852B
• Adapter BNC neg. → TRIAX neg. 1704A1
• Adapter KIAG 10-32 neg. → TRIAX neg. 1704A2 Associated facility 10 (11) ... 36 VDC
• Adapter M4x0.35 neg. → TRIAX neg. 1704A3 2 slot expansion chassis 01
• Adapter TRIAX pos → BNC pos. 1704A4 2 slot base chassis 11
2 slot base chassis with external 12
• PiezoSmart extension cable for 1987B2, AC adapter
Type 5064E12 (TRIAX neg.–TRIAX pos.) 1987B7,
1987B10 Modules for SCP Slim
• PiezoSmart connecting cable forType 1987BFT3,5
5064E13 (Fischer TRIAX neg.–TRIAX pos.) Number Type
4665B1 2 channel piezoresistive amplifier
• Chassis legs 5746A3 with sensor identification
• Expansion kit for cascading SCP Slim 5746A6 5064E11 2 channel charge amplifier
(cascading cable L = 0.4 m), cover plate without sensor identification,
for plugs including mounting material signal input: BNC
• Adaption kit to fit SCP Slim Modules into 5746A5 5064E12 2 channel charge amplifier with
SCP Types 2853B... sensor identification,
signal input: TRIAX
5064E13 2 channel charge amplifier with
sensor identification,
signal input: Fischer TRIAX
5271Y51 2 channel bridge amplifier
2852B_003-204e-03.23

5700A27 Dummy front plate for SCP Slim

19" mounting kit

5746A10 for 1 SCP Slim
5746A11 for 1 and 2 SCP Slim
5746A12 for 2 SCP Slim

Windows, Windows 10, Windows 11, are registered trademarks of the

Microsoft Corporation.
Page 9/9
This information corresponds to the current state of knowledge. Kistler reserves © 2015 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, [email protected], www.kistler.com. Kistler Group products are
from the use of Kistler products is excluded. protected by various intellectual property rights. For more details visit www.kistler.com.