Project: A Proposed (2) Two Story Residencial Building

Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

DESIGN CRITERIA
APPLICABLE CODE AND REFERENCE
1.National Structural Code of the Philippines, NSCP 2015, 7th edition, 2nd printing
2. Uniform Building Code 1997, UBC (Seismic Provisions)
3.Building Code Requirements for Structural Concrete, American Concrete Institute, (ACI 318M-14) and
Commentary (ACI 318RM-14)
4.Manual of Steel Construction, American Institute of Steel Construction, 14th edition
5. American Society of Civil Engineers (ASCE 7-10), Minimum Design Loads for Buildings and Other Structures

MATERIAL PROPERTIES
RC STRUCTURAL ELEMENTS MATERIAL DESIGN STRESSES
Pedestals/Columns/Shear Walls f’c = 21 MPa (3000 Psi)
Floor Slabs/ Beams/ Girders f’c = 21 MPa (3000 Psi)
Foundation (Footing) f’c = 21 MPa (3000 Psi)

DEFORMED BARS MATERIAL DESIGN STRESSES

12mm diameter and smaller fy = 227 MPa (Gr 33)
16mm diameter and larger fy = 275 MPa (Gr 40)

UNIT WEIGHTS
Concrete 23.54 KN/cu.m
Steel 77 KN/cu.m

DEAD AND LIVE LOAD CALCULATIONS

AREA LOAD - SD (SUPERIMPOSED DEAD) LOAD COMPUTATION
2ND FLOOR AND OTHER FLOOR AREAS
Floor finish and floor topping 1.40 KPa
Mechanical duct & other fixtures 0.20 KPa
Suspended Steel Channel Ceiling
0.30 KPa
system
Total 1.90 KPa
ROOF LOAD
Roof 0.60 KPa
Mechanical duct & other fixtures 0.20 KPa
Suspended Steel Channel Ceiling
0.30 KPa
system
Total 1.10 KPa

LINE LOAD - SD (SUPERIMPOSED DEAD) LOAD COMPUTATION

PERIMETER - 2ND FLOOR
Height of CHB wall 2.70 m
Unit weight with plaster 3.11 KPa
Line Load 8.40 KN/m
INTERIOR - 2ND FLOOR
Height of CHB wall 2.70 m
Unit weight with plaster 2.98 KPa
Line Load 8.05 KN/m

LIVE LOAD
Residential Live Load 1.90 KPa
Residential Balcony Live Load 2.90 KPa
Roof Live Load (Lr) 1.00 KPa
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

WIND LOAD PARAMETERS

PARAMETERS
Wind speed at 3 sec gust factor (kph) 260
Wind Speed Input at ETABS (mph) 162
Exposure Category C
Occupancy Standard Occupancy
Importance Factor 1.00
NSCP 2015 basis ASCE 7-10
Lateral Load input in ETABS ASCE 7-10
Structure Type Main Wind Force Resisting System (MWFRS)
Directionality Factor (kd) 0.85
Surface Roughness Category C
Topographic Factor 1.00
Gust Effect Factor 0.85
Design Wind Load Cases Case 1

EARTHQUAKE LOAD PARAMETERS

PARAMETERS
Occupancy Standard Occupancy
Seismic Importance Factor 1.00
Structural System Dual System (Shear Wall and Moment Resisting Frame)
Reduction of base shear factor / 8.50
ductility factor (R)
Story Range from GF to Roof
Eccentricity Ratio 0.05
Time period calculation using 0.02
Method B (Ct)

SAMPLE SOIL INVESTIGATION

REPORT
Soil TypeCONCLUSION SC
Seismic Source Type A
Seismic Zone Factor (under Zone 4) 0.40

Distance to Source 5.2 km

Seismic Near-Source Factor – by interpolation
Na 1.200
Nv 1.600
Seismic Response Coefficients – by interpolation
Ca 0.480
Cv 0.896

LOAD COMBINATIONS
PARAMETERS
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

EARTHQUAKE ACTIVE FAULT

PARAMETERS
Fault Name Valley Fault System
Segment Name West Valley Fault
Distance from fault 5.20 km
Maximum Moment Magnitude 7.0 ≤ M ≤ 8.4
Seismic Source type A
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

DESIGN OF SLABS
PARAMETERS

DESIGN CONSTRAINTS: SLAB THICKNESS CLEAR SPAN

Fy 275.0 MPa Typical floor 125 mm Long direction 4.15 m
f'c 21.0 MPa Clear cover 20 mm Short direction 3.31 m
β 0.85
ρmax 0.028374545 BAR DIAMETERS EFFECTIVE DEPTH
ρmin 0.00509 Long direction 10 mm Long direction 90 mm
γconcrete 23.54 kN/cu.m. Short direction 10 mm Short direction 100 mm

DESIGN OF SLAB

NEGATIVE MOMENTS AT CONTINOUS EDGE CASE No.

m 0.75 0.80 0.797 2
Ca,neg 0.069 0.065 0.0652 m = (la/lb) 0.797
Cb,neg 0.022 0.027 0.0267 Two way Slab

POSITIVE MOMENTS
m 0.75 0.80 0.797 1.2WD 5.811 kPa
Ca,pos,dl 0.028 0.026 0.0261 1.6WL 3.040 kPa
Cb,pos,dl 0.009 0.011 0.0109 WU 8.900 kPa
Ca,pos,ll 0.045 0.041 0.0412
Cb,pos,ll 0.014 0.017 0.0169

MOMENTS

NEGATIVE MOMENTS
At continuous edge At discontinuous edge
Ma,neg 6.338 kN-m Ms N/A
Mb,neg 4.083 kN-m Ml N/A

POSITIVE MOMENTS
Along short direction Along long direction
Ma,pos,dl 1.657 kN-m Mb,pos,dl 1.088 kN-m
Ma,pos,ll 1.368 kN-m Mb,pos,ll .883 kN-m
Ma,pos,total 3.025 kN-m Mb,pos,total 1.971 kN-m

SUMMARY

SHORT DIRECTION LONG DIRECTION

Slab Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 6.338 kN-m 3.025 kN-m N/A 4.083 kN-m 1.971 kN-m N/A
h 125 mm 125 mm 125 mm 125 mm 125 mm 125 mm
d 100 mm 100 mm 100 mm 90 mm 90 mm 90 mm
Rn 0.70422 0.33611111 - 0.560082305 0.27037037 -
Req'd ρ 0.00261 0.00123395 - 0.002069659 0.00099073 -
use ρ 0.00509 0.00509 - 0.00509 0.00509 -
As 509 509 - 458.1 458.1 -
Req'd s 155 155 - 155 155 -
use s 155 155 - 155 155 -
As per plan 150 150 - 150 150 -
Remarks SAFE SAFE - SAFE SAFE -

DESIGN IS SAFE!
 Project Report
A Proposed Two-Storey Residential Building
Model File: Sabaria Residence

Page 1 of 9
ASCE 7-10 Auto Wind Load Calculation
This calculation presents the automatically generated lateral wind loads for load pattern WX according to ASCE 7-
10, as calculated by ETABS.

Exposure Parameters

Exposure From = Diaphragms

Exposure Category = C

Wind Direction = 0 degrees

Basic Wind Speed, V [ASCE 26.5.1] V = 162 mph

Windward Coefficient, Cp,wind [ASCE 27.4.1] Cp,wind = 0.8
Leeward Coefficient, Cp,lee [ASCE 27.4.1] Cp,lee = 0.5

Wind Case = Case 1

Top Story = RF

Bottom Story = FTB

Include Parapet = No

Factors and Coefficients

Gradient Height, zg [ASCE Table 26.9-1] zg = 900

Emperical Exponent, α [ASCE Table 26.9-1] α = 9.5
z
Velocity Pressure Exposure Coefficient, Kz; [ASCE Table 27.3-1] Kz = 2.01(zg for 15ft ≤ z ≤ zg
15
Kz = 2.01(zg for z 15ft
Topographical Factor, Kzt [ASCE 26.8.2] Kzt = 1
Directionality Factor, Kd [ASCE 26.6] Kd = 0.85
Gust Effect Factor, G [ASCE 26.9] G = 0.85

Lateral Loading

Velocity Pressure, qz [ASCE 27.3.2 Eq. 27.3-1] qz = 0.00256Kz Kzt Kd V2

Design Wind Pressure, p [ASCE 27.4.2 Eq. 27.4-2] p = qGCp,wind + qh (GCp,lee )

Page 2 of 9
Applied Story Forces

Story Elevation X-Dir Y-Dir

m kN kN
RF 8.3 47.7229 0
2ND 5.3 165.2315 0
FTB 1.5 91.9165 0
Base 0 0 0

Page 3 of 9
ASCE 7-10 Auto Wind Load Calculation
This calculation presents the automatically generated lateral wind loads for load pattern WY according to ASCE 7-
10, as calculated by ETABS.

Exposure Parameters

Exposure From = Diaphragms

Exposure Category = C

Wind Direction = 0 degrees

Basic Wind Speed, V [ASCE 26.5.1] V = 162 mph

Windward Coefficient, Cp,wind [ASCE 27.4.1] Cp,wind = 0.8
Leeward Coefficient, Cp,lee [ASCE 27.4.1] Cp,lee = 0.5

Wind Case = Case 1

Top Story = RF

Bottom Story = FTB

Include Parapet = No

Factors and Coefficients

Gradient Height, zg [ASCE Table 26.9-1] zg = 900

Emperical Exponent, α [ASCE Table 26.9-1] α = 9.5
z
Velocity Pressure Exposure Coefficient, Kz; [ASCE Table 27.3-1] Kz = 2.01(zg for 15ft ≤ z ≤ zg
15
Kz = 2.01(zg for z 15ft
Topographical Factor, Kzt [ASCE 26.8.2] Kzt = 1
Directionality Factor, Kd [ASCE 26.6] Kd = 0.85
Gust Effect Factor, G [ASCE 26.9] G = 0.85

Lateral Loading

Velocity Pressure, qz [ASCE 27.3.2 Eq. 27.3-1] qz = 0.00256Kz Kzt Kd V2

Design Wind Pressure, p [ASCE 27.4.2 Eq. 27.4-2] p = qGCp,wind + qh (GCp,lee )

Page 4 of 9
Applied Story Forces

Story Elevation X-Dir Y-Dir

m kN kN
RF 8.3 47.7229 0
2ND 5.3 165.2315 0
FTB 1.5 91.9165 0
Base 0 0 0

Page 5 of 9
4.3 Auto Seismic Loading

UBC 97 Auto Seismic Load Calculation

This calculation presents the automatically generated lateral seismic loads for load pattern EXstat according to
UBC 97, as calculated by ETABS.

Direction and Eccentricity

Direction = X + Eccentricity Y

Eccentricity Ratio = 5% for all diaphragms

Structural Period

Period Calculation Method = Program Calculated

Coefficient, Ct [UBC 1630.2.2] Ct = 0.02ft

Structure Height Above Base, hn hn = 22.31 ft
Approximate Fundamental Period, Ta [UBC
Ta = Ct (hn )^3/4 Ta = 0.205 sec
1630.2.2 Eq. 30-8]
Program Calculated Period, T [UBC
T ≤ 1.3Ta
1630.2.2.2]

Factors and Coefficients

Response Modification Factor, R [UBC Table 16-N] R = 8.5

Importance Factor, I [UBC Table 16-K] I=1
Seismic Zone Factor, Z [UBC Table 16-I] Z = 0.4
Soil Profile [UBC Table 16-J] = SC
Seismic Source Type = A
Closest Source Distance = 5 km
Near-Source Factor, Na [UBC Table 16-S] Na = 1.2
Near-Source Factor, Nv [UBC Table 16-T] Nv = 1.6
Site Coefficient, Ca [UBC Table 16-Q] Ca = 0.48
Site Coefficient, Cv [UBC Table 16-R] Cv = 0.896

Equivalent Lateral Forces

Cv I
Base Shear Coefficient [UBC 1630.2.1, Eq. 30-4] =
RT
2.5Ca I
maximum [UBC 1630.2.1, Eq. 30-5] = = 0.141176
R
minimum [UBC 1630.2.1, Eq. 30-6] = 0.11Ca I = 0.0528
0.8ZNv I
Zone 4 minimum [UBC 1630.2.1, Eq. 30-7] = = 0.060235
R
min ≤ Vcoeff ≤ max

Page 6 of 9
Calculated Base Shear

Period Used W V Ft
Direction Vcoeff
(sec) (kN) (kN) (kN)
X + Ecc. Y 0.267 0 2045.9451 288.8393 0

Applied Story Forces

Story Elevation X-Dir Y-Dir

m kN kN
RF 8.3 78.3991 0
2ND 5.3 210.4402 0
FTB 1.5 0 0
Base 0 0 0

Page 7 of 9
UBC 97 Auto Seismic Load Calculation
This calculation presents the automatically generated lateral seismic loads for load pattern EYstat according to
UBC 97, as calculated by ETABS.

Direction and Eccentricity

Direction = Y + Eccentricity X

Eccentricity Ratio = 5% for all diaphragms

Structural Period

Period Calculation Method = Program Calculated

Coefficient, Ct [UBC 1630.2.2] Ct = 0.02ft

Structure Height Above Base, hn hn = 22.31 ft
Approximate Fundamental Period, Ta [UBC
Ta = Ct (hn )^3/4 Ta = 0.205 sec
1630.2.2 Eq. 30-8]
Program Calculated Period, T [UBC
T ≤ 1.3Ta
1630.2.2.2]

Factors and Coefficients

Response Modification Factor, R [UBC Table 16-N] R = 8.5

Importance Factor, I [UBC Table 16-K] I=1
Seismic Zone Factor, Z [UBC Table 16-I] Z = 0.4
Soil Profile [UBC Table 16-J] = SC
Seismic Source Type = A
Closest Source Distance = 5 km
Near-Source Factor, Na [UBC Table 16-S] Na = 1.2
Near-Source Factor, Nv [UBC Table 16-T] Nv = 1.6
Site Coefficient, Ca [UBC Table 16-Q] Ca = 0.48
Site Coefficient, Cv [UBC Table 16-R] Cv = 0.896

Equivalent Lateral Forces

Cv I
Base Shear Coefficient [UBC 1630.2.1, Eq. 30-4] =
RT
2.5Ca I
maximum [UBC 1630.2.1, Eq. 30-5] = = 0.141176
R
minimum [UBC 1630.2.1, Eq. 30-6] = 0.11Ca I = 0.0528
0.8ZNv I
Zone 4 minimum [UBC 1630.2.1, Eq. 30-7] = = 0.060235
R
min ≤ Vcoeff ≤ max

Page 8 of 9
Calculated Base Shear

Period Used W V Ft
Direction Vcoeff
(sec) (kN) (kN) (kN)
Y + Ecc. X 0.267 0 2045.9451 288.8393 0

Applied Story Forces

Story Elevation X-Dir Y-Dir

m kN kN
RF 8.3 0 78.3991
2ND 5.3 0 210.4402
FTB 1.5 0 0
Base 0 0 0

Page 9 of 9
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala,
Client: Caloocan City B. Sabaria & Ethel F. Sabaria
Sps. Reynaldo
Subject: Structural Analysis

LONGITUDINAL REINFORCEMENT CHECKING

PLAN VIEW (ACI 318-14)

DESIGN IS SAFE!
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

LONGITUDINAL REINFORCEMENT CHECKING

PLAN VIEW (ACI 318-14)

DESIGN IS SAFE!
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

LONGITUDINAL REINFORCEMENT CHECKING

PLAN VIEW (ACI 318-14)

DESIGN IS SAFE!
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub. Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

LONGITUDINAL REINFORCEMENT CHECKING

3-D VIEW (ACI 318-14)

DESIGN IS SAFE!
Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F1
Foundation Parameters:

Assumed allowable bearing capacity = qa = 150 Kpa

P= 111.17 kN Pu = 155.6244 kN
Mx = 10.85 kN-m Mux = 15.1837 kN-m
My = 37.59 kN-m Muy = 52.6294 kN-m
qa = 150 kPa col x dist. to left edge, Bl = 375 mm
col dim., Cx or Ø = 250 mm col x dist. to right edge, Br = 375 mm
col dim., Cy if Rec. = 400 mm col y dist. to top edge, Yt = 300 mm
ftng thk., t = 300 mm col y dist. to bot. edge, Yb = 300 mm
conc. cover, Cc = 75 mm footing width, Bx = 1.00 m
bar dia., Bd = 16 mm footing y length, Ly = 1.00 m
f'c = 21 Mpa fy = 275 Mpa
foundation to NGL = 1.5 m density of soil = 18 KN/m^3

Check Bearing Pressure

@ Service:
qnet = 121.20 kPa
q= 111.17 kPa
F.S. = 1.09 OK

Beam Shear Check:

Check Beam Shear: Vc = Vu / b*d

d= 217 mm
Φ= 0.75
ΦVc allow =Φ√f'c/6 = 0.573 MPa

@ distance d of Y-Direction: @ distance d of X-Direction:

Vu y = 44.51 kN Vu x = 86.60 kN
Vc y = 0.205 MPa Vc y = 0.399 MPa
ΦVc > Vc y, OK ΦVc > Vc x, OK

: SAFE, Thickness is adequate

Project: A Proposed (2) Two Story Residencial Building
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F1
Punching Shear Check:

Check Actual Punching Shear: Vp = Vup / bo*d

bo = perimeter @ 0.5d
bo = 2168 mm

Vup = Pu - (qunet*Ao)
Ao = 0.29 sq.m.
Vup = 155.6244 kN
Vp = Vup/(bo*d) = 0.331 MPa

Allowable Punching Shear:

vp allow. = 0.083 [2 + (4/βc)] f'c^.5

vp allow. = 1.7116 MPa

vp allow. = 0.083 [(αd / bo)+2] f'c^.5 :use vp allow = 1.528 MPa

vp allow. = 2.2835 MPa Φvp allow = 1.146 MPa

vp allow. = (f'c ^0.5)/3

vp allow. = 1.528 MPa

: SAFE, Thickness is adequate

Reinforcement Checking:

Check Reinforcement: (Using maximum soil pressure)

@ X-Direction:
Lcx = 0.38 m
Mux = 49.55 kN-m
ρ= 0.004401 ρ min = 0.00276
2
As =ρbd = 955.0 mm
5 -16 mm diameter

@ Y-Direction:
Bcy = 0.30 m
Muy = 35.31 kN-m
ρ= 0.003104
As =ρbd = 683.6 mm2
4 -16 mm diameter

Recommendation:
Use 5 nos. of 16mm diameter rebar at equal spacing bothways SPACED at 208.5
Project: A Proposed (2) Two Story Residence
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F2
Foundation Parameters:

Assumed allowable bearing capacity = qa = 150 Kpa

P= 157.37 kN Pu = 220.3085 kN
Mx = 11.02 kN-m Mux = 15.4299 kN-m
My = 42.22 kN-m Muy = 59.1093 kN-m
qa = 150 kPa col x dist. to left edge, Bl = 475 mm
col dim., Cx or Ø = 250 mm col x dist. to right edge, Br = 475 mm
col dim., Cy if Rec. = 400 mm col y dist. to top edge, Yt = 400 mm
ftng thk., t = 300 mm col y dist. to bot. edge, Yb = 400 mm
conc. cover, Cc = 75 mm footing width, Bx = 1.20 m
bar dia., Bd = 16 mm footing y length, Ly = 1.20 m
f'c = 21 Mpa fy = 275 Mpa
foundation to NGL = 1.5 m density of soil = 18 KN/m^3

Check Bearing Pressure

@ Service:
qnet = 121.20 kPa
q= 109.29 kPa
F.S. = 1.11 OK

Beam Shear Check:

Check Beam Shear: Vc = Vu / b*d

d= 217 mm
Φ= 0.75
ΦVc allow =Φ√f'c/6 = 0.573 MPa

@ distance d of Y-Direction: @ distance d of X-Direction:

Vu y = 83.56 kN Vu x = 123.93 kN
Vc y = 0.321 MPa Vc y = 0.476 MPa
ΦVc > Vc y, OK ΦVc > Vc x, OK

: SAFE, Thickness is adequate

Project: A Proposed (2) Two Story Residence
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F2
Punching Shear Check:

Check Actual Punching Shear: Vp = Vup / bo*d

bo = perimeter @ 0.5d
bo = 2168 mm

Vup = Pu - (qunet*Ao)
Ao = 0.29 sq.m.
Vup = 220.3085 kN
Vp = Vup/(bo*d) = 0.468 MPa

Allowable Punching Shear:

vp allow. = 0.083 [2 + (4/βc)] f'c^.5

vp allow. = 1.7116 MPa

vp allow. = 0.083 [(αd / bo)+2] f'c^.5 :use vp allow = 1.528 MPa

vp allow. = 2.2835 MPa Φvp allow = 1.146 MPa

vp allow. = (f'c ^0.5)/3

vp allow. = 1.528 MPa

: SAFE, Thickness is adequate

Reinforcement Checking:

Check Reinforcement: (Using maximum soil pressure)

@ X-Direction:
Lcx = 0.48 m
Mux = 65.75 kN-m
ρ= 0.004885 ρ min = 0.00276
2
As =ρbd = 1272.2 mm
7 -16 mm diameter

@ Y-Direction:
Bcy = 0.40 m
Muy = 49.53 kN-m
ρ= 0.003644
As =ρbd = 959.0 mm2
5 -16 mm diameter

Recommendation:
Use 7 nos. of 16mm diameter rebar at equal spacing bothways SPACED at 172.3333333
Project: A Proposed (2) Two Story Residence
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F3
Foundation Parameters:

Assumed allowable bearing capacity = qa = 150 Kpa

P= 199.59 kN Pu = 279.4215 kN
Mx = 9.99 kN-m Mux = 13.9794 kN-m
My = 32.37 kN-m Muy = 45.3196 kN-m
qa = 150 kPa col x dist. to left edge, Bl = 525 mm
col dim., Cx or Ø = 250 mm col x dist. to right edge, Br = 525 mm
col dim., Cy if Rec. = 400 mm col y dist. to top edge, Yt = 450 mm
ftng thk., t = 300 mm col y dist. to bot. edge, Yb = 450 mm
conc. cover, Cc = 75 mm footing width, Bx = 1.30 m
bar dia., Bd = 16 mm footing y length, Ly = 1.30 m
f'c = 21 Mpa fy = 275 Mpa
foundation to NGL = 1.5 m density of soil = 18 KN/m^3

Check Bearing Pressure

@ Service:
qnet = 121.20 kPa
q= 118.11 kPa
F.S. = 1.03 OK

Beam Shear Check:

Check Beam Shear: Vc = Vu / b*d

d= 217 mm
Φ= 0.75
ΦVc allow =Φ√f'c/6 = 0.573 MPa

@ distance d of Y-Direction: @ distance d of X-Direction:

Vu y = 92.41 kN Vu x = 127.42 kN
Vc y = 0.328 MPa Vc y = 0.452 MPa
ΦVc > Vc y, OK ΦVc > Vc x, OK

: SAFE, Thickness is adequate

Project: A Proposed (2) Two Story Residence
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F3
Punching Shear Check:

Check Actual Punching Shear: Vp = Vup / bo*d

bo = perimeter @ 0.5d
bo = 2168 mm

Vup = Pu - (qunet*Ao)
Ao = 0.29 sq.m.
Vup = 271.3951349 kN
Vp = Vup/(bo*d) = 0.577 MPa

Allowable Punching Shear:

vp allow. = 0.083 [2 + (4/βc)] f'c^.5

vp allow. = 1.7116 MPa

vp allow. = 0.083 [(αd / bo)+2] f'c^.5 :use vp allow = 1.528 MPa

vp allow. = 2.2835 MPa Φvp allow = 1.146 MPa

vp allow. = (f'c ^0.5)/3

vp allow. = 1.528 MPa

: SAFE, Thickness is adequate

Reinforcement Checking:

Check Reinforcement: (Using maximum soil pressure)

@ X-Direction:
Lcx = 0.53 m
Mux = 68.63 kN-m
ρ= 0.004701 ρ min = 0.00276
2
As =ρbd = 1326.0 mm
7 -16 mm diameter

@ Y-Direction:
Bcy = 0.45 m
Muy = 53.08 kN-m
ρ= 0.003603
As =ρbd = 1026.5 mm2
6 -16 mm diameter

Recommendation:
Use 7 nos. of 16mm diameter rebar at equal spacing bothways SPACED at 189
Project: A Proposed (2) Two Story Residence
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F4
Foundation Parameters:

Assumed allowable bearing capacity = qa = 150 Kpa

P= 251.16 kN Pu = 351.6174 kN
Mx = 14.58 kN-m Mux = 20.407 kN-m
My = 35.17 kN-m Muy = 49.2426 kN-m
qa = 150 kPa col x dist. to left edge, Bl = 625 mm
col dim., Cx or Ø = 250 mm col x dist. to right edge, Br = 625 mm
col dim., Cy if Rec. = 450 mm col y dist. to top edge, Yt = 525 mm
ftng thk., t = 300 mm col y dist. to bot. edge, Yb = 525 mm
conc. cover, Cc = 75 mm footing width, Bx = 1.50 m
bar dia., Bd = 16 mm footing y length, Ly = 1.50 m
f'c = 21 Mpa fy = 275 Mpa
foundation to NGL = 1.5 m density of soil = 18 KN/m^3

Check Bearing Pressure

@ Service:
qnet = 121.20 kPa
q= 111.63 kPa
F.S. = 1.09 OK

Beam Shear Check:

Check Beam Shear: Vc = Vu / b*d

d= 217 mm
Φ= 0.75
ΦVc allow =Φ√f'c/6 = 0.573 MPa

@ distance d of Y-Direction: @ distance d of X-Direction:

Vu y = 121.10 kN Vu x = 165.38 kN
Vc y = 0.372 MPa Vc y = 0.508 MPa
ΦVc > Vc y, OK ΦVc > Vc x, OK

: SAFE, Thickness is adequate

Project: A Proposed (2) Two Story Residence
Location: Blk 17 lot 27 Guadanoville sub.Brgy. 183 Tala, Caloocan City
Client: Sps. Reynaldo B. Sabaria & Ethel F. Sabaria
Subject: Structural Analysis

FOOTING DESIGN - F4
Punching Shear Check:

Check Actual Punching Shear: Vp = Vup / bo*d

bo = perimeter @ 0.5d
bo = 2268 mm

Vup = Pu - (qunet*Ao)
Ao = 0.31 sq.m.
Vup = 333.7263741 kN
Vp = Vup/(bo*d) = 0.678 MPa

Allowable Punching Shear:

vp allow. = 0.083 [2 + (4/βc)] f'c^.5

vp allow. = 1.6059 MPa

vp allow. = 0.083 [(αd / bo)+2] f'c^.5 :use vp allow = 1.528 MPa

vp allow. = 2.2164 MPa Φvp allow = 1.146 MPa

vp allow. = (f'c ^0.5)/3

vp allow. = 1.528 MPa

: SAFE, Thickness is adequate

Reinforcement Checking:

Check Reinforcement: (Using maximum soil pressure)

@ X-Direction:
Lcx = 0.63 m
Mux = 92.06 kN-m
ρ= 0.005499 ρ min = 0.00276
2
As =ρbd = 1790.1 mm
9 -16 mm diameter

@ Y-Direction:
Bcy = 0.53 m
Muy = 67.90 kN-m
ρ= 0.004008
As =ρbd = 1314.6 mm2
7 -16 mm diameter

Recommendation:
Use 9 nos. of 16mm diameter rebar at equal spacing bothways SPACED at 166.75
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF C4 3 C 250x250 6-12 DCon28 2700 3000 1 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
13.7124 -0.2404 0.3118 0.3118 0.3118 1.09 0.022

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.6 1 1 1 2700
Minor Bend(M2) 0.6 1 1 1 2700

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 17.1097 0 17.1097 17.1097 502.49
Minor, Vu3 0.1226 0 0.1226 0 4.5

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 0 0 109.0391 301.0474 625 0.362
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF C1 24 C 250x250 (4-16,2-12) DCon28 2700 3000 0.871 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
24.5237 6.4098 3.5201 0.5577 0.5577 1.65 0.274

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.307328 1 1 1 2700
Minor Bend(M2) 0.687767 1 1 1 2700

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 8.857 0 8.857 8.857 260.12
Minor, Vu3 22.093 0 22.093 22.093 648.84

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 0 0 55.3504 401.3965 625 0.138
Minor Shear, Vu3 0 0 141.7483 401.3965 625 0.353
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc
RF C24 32 C 250x400 (4-16,2-12) DCon21 0

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar %
kN kN-m kN-m kN-m kN-m %
18.3192 11.7716 14.98 0.4166 0.499 1.03

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.35814 1 1 1 2700
Minor Bend(M2) 0.689307 1 1 1 2700

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 15.1081 0 15.1081 15.1081 259.47
Minor, Vu3 3.3849 35.2795 0 0 0

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear

Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 N/A N/A N/A N/A N/A N/A
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND C20 59 C 250x400 (6-16) DCon23 0 3800 1 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
37.3179 2.9353 43.3869 0.8486 1.0165 1.21 0.794

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.252135 1 1 1 3400
Minor Bend(M2) 0.324706 1 1 1 3400

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 23.6882 0 23.6882 25.2882 508.54
Minor, Vu3 1.4351 35.7592 0 0 0

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 N/A N/A N/A N/A N/A N/A
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF C15 220 C 250x400 (8-16) DCon22 0 3000 1 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
47.7918 33.7631 -8.7626 1.0868 1.3018 1.61 0.885

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.376847 1 1 1 2700
Minor Bend(M2) 0.363512 1 1 1 2700

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 18.944 0 18.944 18.944 325.35
Minor, Vu3 19.8264 36.0237 16.5474 0 607.47

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 N/A N/A N/A N/A N/A N/A
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF C6 219 C 250 x 400 (10-16) DCon22 0 3000 1 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
43.9595 39.6297 -9.2237 0.9996 1.1975 2.01 0.906

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.441914 1 1 1 2700
Minor Bend(M2) 0.414793 1 1 1 2700

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 18.026 0 18.026 18.026 309.59
Minor, Vu3 21.4063 35.9269 16.5474 0 607.47

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 N/A N/A N/A N/A N/A N/A
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND C35 67 C 250x400 (12-16) DCon24 3800 3800 1 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
102.4511 35.9205 43.9769 2.3297 2.7908 2.41 0.914

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.25044 1 1 1 3800
Minor Bend(M2) 0.493504 1 1 1 3800

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 21.4498 0 21.4498 0 460.49
Minor, Vu3 12.0551 37.4038 0 0 0

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 N/A N/A N/A N/A N/A N/A
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND C30 74 C 300x450 (14-16) DCon28 3400 3800 1 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
74.9098 31.4676 47.2269 1.8158 2.1529 2.09 0.557

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.270743 1 1 1 3400
Minor Bend(M2) 0.464889 1 1 1 3400

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 45.3208 0 45.3208 45.3208 679.08
Minor, Vu3 55.1885 0 55.1885 55.1885 1339.5

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 0 0 264.0526 650.2624 1350 0.406
Minor Shear, Vu3 0 0 346.5096 520.2099 1350 0.666
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND C2 13 C 300x450 (14-20) DCon22 3800 3800 0.928 Sway Special

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint Ω0
0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For Pu , Mu2 , Mu3

Design Pu Design Mu2 Design Mu3 Minimum M2 Minimum M3 Rebar % Capacity Ratio
kN kN-m kN-m kN-m kN-m % Unitless
135.4888 -71.5893 91.4595 3.2842 3.8939 3.26 0.943

Axial Force and Biaxial Moment Factors

Cm Factor δns Factor δs Factor K Factor Effective Length
Unitless Unitless Unitless Unitless mm
Major Bend(M3) 1 1.051616 1 1 5300
Minor Bend(M2) 1 1.124146 1 1 5300

Shear Design for Vu2 , Vu3

Shear Vu Shear ΦVc Shear ΦVs Shear ΦVp Rebar Av /s
kN kN kN kN mm²/m
Major, Vu2 24.2834 56.9017 0 0 0
Minor, Vu3 21.6337 52.5248 0 0 0

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear
Force Vu,Top Vu,Tot ΦVc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, Vu2 N/A N/A N/A N/A N/A N/A
Minor Shear, Vu3 N/A N/A N/A N/A N/A N/A
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
FTB B80 179 FTB 200x350 DCon22 0 3620 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 350 200 0 58 58

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -21.9305 317 0 293 317
Bottom (-2 Axis) 10.9653 0 155 207 207

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
19.8145 0 19.8145 16.043 398.58

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.0009 1.2621 5.0486 246.6 744.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND B93 140 B0 200x350 DCon24 2220 3345 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 350 200 0 58 58

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -2.4052 33 0 45 45
Bottom (-2 Axis) 15.676 0 224 293 293

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
7.9684 33.094 0 5.4203 0

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.0012 1.2621 5.0486 246.6 744.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm)
2ND B49 45 B1 250x400 DCon24 0 3345

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 400 250 0 58 58

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required

-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -39.732 491 0 429 491
Bottom (-2 Axis) 19.866 0 240 320 320

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
58.072 38.7607 19.3112 16.8288 414.58

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.0494 2.1795 8.7181 426 944.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF
2ND B58 66 B2 250x400 DCon21 3520 3620 1

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 400 250 0 58 58

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required

-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -58.3611 739 0 429 739
Bottom (-2 Axis) 0.0834 0 1 1 1

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
77.4448 0 77.4448 44.7882 1330.08

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
1.0825 2.1795 8.7181 426 944.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND B33 65 B3 250x400 DCon21 4495 4595 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 400 250 0 82.5 82.5

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -83.2209 1201 0 398 1201
Bottom (-2 Axis) 41.6104 0 560 398 560

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
126.1452 44.98 81.1651 50.5472 1501.55

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
2.2197 2.1795 8.7181 426 944.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
2ND B14 141 B4 250x400 DCon24 100 6600 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 400 250 0 82.5 82.5

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -104.777 1579 0 398 1579
Bottom (-2 Axis) 0.0009 0 1.156E-02 1.541E-02 1.541E-02

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
84.1116 35.984 48.1276 0.0022 1112.94

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
2.7111 2.1795 8.7181 426 944.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF B71 123 RB0 200X250 DCon1 0 3345 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 250 200 0 58 58

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -5.3565 115 0 154 154
Bottom (-2 Axis) 2.6782 0 57 76 76

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
8.688 21.7604 0 2.9529 0

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.0014 0.7871 3.1482 152.1 544.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF B35 273 RB1 200x300 DCon23 3270 3270 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 300 200 0 56 56

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -9.8055 166 0 221 221
Bottom (-2 Axis) 4.9028 0 81 108 108

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
14.6483 0 14.6483 8.0581 352.62

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.2439 1.0228 4.0913 199.4 644.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
RF B13 29 RB2 200x300 DCon22 75 3555 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 300 200 0 56 56

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required
-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -15.6428 269 0 245 269
Bottom (-2 Axis) 0.5014 0 7 9 9

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
17.8307 0 17.8307 10.5299 429.23

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.3398 1.0232 4.0927 199.4 644.4 0 0
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm)
RF B32 103 RB3 250x300 DCon21 4560 4660

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 300 250 0 56 56

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
21384 20.7 1 275 227

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, Mu3

Design Design -Moment +Moment Minimum Required

-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -29.0416 514 0 306 514
Bottom (-2 Axis) 0 0 0 0 0

Shear Force and Reinforcement for Shear, Vu2

Shear Vu2 Shear ΦVc Shear ΦVs Shear Vp Rebar Av /S
kN kN kN kN mm²/m
27.2246 34.5673 0 7.2274 0

Torsion Force and Torsion Reinforcement for Torsion, Tu

Φ*Tu Tth Tcr Area Ao Perimeter, ph Rebar At /s Rebar Al
kN-m kN-m kN-m cm² mm mm²/m mm²
0.4246 1.4523 5.8093 289.1 744.4 0 0