www.ti.

com

Technical Article
Protector, Monitor or Gauge – Selecting the Correct
Battery Electronics for Your Li-ion-powered System

Matt Sunna
Lithium-ion batteries have high energy density and a long cycle life; they also lack the memory effect of other
technologies. Such characteristics make them attractive for portable electronic systems. But lithium-ion batteries
also need to operate within specified limits to be used safely, so batteries require electronics designed to
respond or provide a signal to the system if the limits are exceeded.
Battery electronics monitor multiple conditions such as voltage, current and temperature and how they change
over time. They need to sense the required combination of these parameters in order to respond, whether that’s
sending a signal to the system, activating a switch to prevent charge or discharge, or opening a fuse. Figure 1
below shows an example of how the battery electronics might be configured in a typical battery pack.

Figure 1. Battery Electronics within a Battery Pack

The type of battery electronics varies depending on the type of battery pack. Simple packs may need only a
simple protector, ranging from a basic overvoltage protector to a more advanced protector that responds to
under-voltage, temperature faults or current faults. Protectors can also operate as a secondary device along with
a monitor or battery gauge.
Many advanced battery packs used in higher-cell-count batteries require a battery monitor. A battery monitor
measures individual cell voltages, battery current and temperature, and reports these values to a gauge or
microcontroller. The system uses this information to adjust performance accordingly; for example, by reducing
the operating current if the temperature is too high. Battery monitors may provide a cell-balancing feature to
extend battery run times as well as battery lifetimes. Monitors can also include protections available in integrated
circuits (ICs), but with much higher configurability.
A gauge IC integrates the features of a battery monitor with a controller to provide advanced gauging algorithms.
Gauge ICs report the remaining battery capacity, run time and state of charge. Software-based algorithms can
enhance protections even further. Gauges often include other useful features such as a black-box function that
helps diagnose battery packs that failed in the field, lifetime data logging of minimum and maximum parameter
conditions, dynamic charger control, or authentication for secure batteries.
Figure 2 below outlines some of the key feature differences between the different types of battery electronics.

SSZT466 – JUNE 2019 Protector, Monitor or Gauge – Selecting the Correct Battery Electronics for 1
Submit Document Feedback Your Li-ion-powered System
Copyright © 2023 Texas Instruments Incorporated
 www.ti.com

Figure 2. Feature Differences between Protectors, Monitors and Gauges

What Features Are Most Critical in Choosing the Optimal Battery Electronics for Your System?
When evaluating the pros and cons of each battery electronics option, it’s important to consider the following
characteristics of each:
• Protectors offer the lowest complexity for simple pack designs.
• Monitors offer the highest flexibility. You can write code specific to your system needs, which is often
important when those needs are unique.
• Gauge ICs offer the highest level of integration. They offer high-accuracy state-of-charge information and
faster development time – since firmware is included – but might limit flexibility.
Figure 3 shows an example solution using the BQ769x0 battery monitor. The family includes devices for five-
(BQ76920), 10- (BQ76930) and 15-cell (BQ76940) batteries. You can use the same controller software for
any of the devices in the family, enabling flexibility for systems to go from three to 15 cells in series. The
monitor continuously measures cell voltages, temperature and current through the sense resistor and reports
this information to the microcontroller. It provides multiple configurable hardware protections and will open
charge and discharge field-effect transistors (FETs) as needed to respond to fault conditions. The microcontroller
can make decisions based on the information provided by the monitor – it can also enable/disable the FETs;
control the cell-balancing feature; and even perform some basic gas gauging based on voltage, current and
temperature information.

Figure 3. Example Battery Monitor Solution Featuring the BQ769x0 with a Microcontroller

2 Protector, Monitor or Gauge – Selecting the Correct Battery Electronics for SSZT466 – JUNE 2019
Your Li-ion-powered System Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com

Figure 4 is an example of a slightly more advanced battery pack. Here, you see the same monitor family working
with the BQ78350-R1 companion controller. The BQ78350-R1 comes equipped with firmware designed to work
directly with the BQ7620, the BQ76930 or the BQ76940 digital monitor, helping accelerate product development.
The BQ78350-R1 also performs fuel gauging and state-of-health reporting and includes many other features
commonly included in TI fuel gauges, such as lifetime data logging and black-box recording.

Figure 4. Advanced Battery Pack Featuring the BQ769x0, BQ78350-R1 Controller with Fuel Gauge,
BQ76200 High-side FET Driver and BQ7718 Secondary Protector

Many systems require the redundancy of a secondary protector for overvoltage. This example features the
BQ7718 stackable overvoltage protector, which can directly open a fuse if the primary protector fails.
Some systems may require the use of high-side FETs. High-side FETs enable continuous communication to the
pack regardless of whether they are on or off. This means that the system can read critical pack parameters
despite safety faults, and access pack conditions before allowing operations to resume. The BQ76200 high-side
N-channel FET driver works well with the BQ76920, BQ76930 and BQ76940 monitors in systems needing
high-side FETs.
There are many things to consider when designing systems with Lithium Ion batteries for safety and battery
performance. Depending on the system needs, the appropriate protector, battery monitor or gauge can be
selected.

Additional Resources
• Learn more about TI’s battery protectors, battery monitors or fuel gauges.
• Watch the training video, Battery protector, monitor, or gauge?

SSZT466 – JUNE 2019 Protector, Monitor or Gauge – Selecting the Correct Battery Electronics for 3
Submit Document Feedback Your Li-ion-powered System
Copyright © 2023 Texas Instruments Incorporated
 IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated