SERVICE MANUAL

X1126AH/X1226AH/X1326AWH

Date Revise Version Description

2018.12.03 V1.0 Initial Issue

Copyright Dec. 2018 All Rights Reserved

Prepared: Amy Checked: Alick Approved: Alick

Preface
This manual is applied to X1126AH/X1226AH/X1326AWH projection system.The manual
gives you a brief description of basic technical information to help in service and maintain
the product.
Your customers will appreciate the quick response time when you immediately identify
problems that occur with our products.We expect your customers will appreciate the
service that you offer them.
This manual is for technicians and people who have an electronic background.Please send
the product back to the distributor for repairing and do not attempt to do anything that is
complex or not mentioned in the troubleshooting.

Note: The information found in this manual is subject to change without prior notice.Any
subsequent changes made to the data herein will be incorporated in future edition.

X1126AH/X1226AH/X1326AWH Service Manual

Copyright Dec.2018
All Rights Reserved
Manual Version 1.0

X1126AH/X1226AH/X1326AWH Confidential 2
Table of Content

Chapter 1 Introduction
Highlight 1-1
Compatible Mode 1-5
Product Overview 1-10

Chapter 2 Disassembly & Assembly Process

Equipment Needed & Product Overview 2-1
Disassemble Lamp Cover 2-2
Disassemble Lamp Module 2-2
Disassemble Top Cover Module 2-3
Disassemble Main Board Modul 2-5
Disassemble Speaker 2-6
Disassemble IO Cover Module 2-7
Disassemble Systrm Fan 2-8
Disassemble Engine Module 2-9
Disassemble LVPS 2-12
Disassemble Bottom Cover Module 2-13
Assemble Bottom Cover Module 2-14
Assemble LVPS 2-15
Assemble Engine Module 2-16
Assemble Systrm Fan 2-18
Assemble IO Cover Module 2-20
Assemble Main Board 2-20
����������������������������������������������������������
Assemble Top Cover Module 2-22
Assemble Lamp Module 2-23
Assemble Lamp Cover 2-24
Rod Adjustment 2-25
Repair Action 2-26

X1126AH/X1226AH/X1326AWH Confidential 4
Chapter 3 Troubleshooting

LED Lighting Message 3-1

Main Procedure 3-2

Chapter 4 Test & Inspection

Test Equipment Needed 4-1

Test Condition 4-1
Auto Waveform and Fan Calibration 4-2
Calibration 4-2
I/O Port Test 4-4
Optical Performance Measure 4-8
Burn in Test 4-9
Test Inspection Procedure 4-10
Re-write System and Lamp Usage Hour 4-12

Chapter 5 Firmware Upgrade

Section1 System Firmware Upgrade 5-1

Section2 MCU Firmware Upgrade 5-9

Chapter 6 EDID Upgrade

EDID Introduction 6-1

Equipment Needed 6-2
Setup Procedure 6-3
EDID Key-In Procedure 6-4

X1126AH/X1226AH/X1326AWH Confidential 5
Appendix A
Exploded Overview I
FRU List II

Appendix B
Serial Number System Definition I
PCBA Code Definition II

Appendix C

X1126AH/X1226AH/X1326AWH Confidential 6
X1126AH/X1226AH/X1326AWH Comparison List

X1126AH X1226AH A1326AWH

MAIN BOARD 70.7B958GR01 70.7BT24GR01 70.7BK19GR01

DMD 48.8EH01G005 48.8CQ01G009 48.8EJ01G007

DMD BD 80.7AR12G001 80.7BK02G001 80.7BK02G001
ENGINE MODULE 70.7B957GR01 70.7BT14GR01 70.7BK09GR01

X1126AH/X1226AH/X1326AWH Confidential
Chapter 1

Introduction
1-1 Highlight
No Item Description
For X1126AH
● TI DMD 0.55” DC3 S450 SVGA
For X1226AH
1 Technology
● TI 0.55” S450 DC3 DMD XGA
For X1326AWH
● TI 0.65” S450 DC3 DMD WXGA

● 313 mm X 240 mm X 103.4 mm (w/o feet)

2 Dimension (W x H x D)
● 313 mm X 240 mm X 113.7 mm (w/ feet)

3 Weight ● 2.8 kg

4 Power Supply ● Universal AC 100 – 240 V~50-60 Hz with PFC

5 Keystone Correction ● ± 40 degree (80 degree)

For X1126AH
● 800(H) x 600(V)
For X1226AH
6 Number of Active dots
● 1024(H) x 768(V)
For X1326AWH
● 1280(H) x 800(V)
For X1126AH
● 1.94 ~ 2.16:1(D/W) 60”@ 2m
For X1226AH
● 1.94 (Wide) ~ 2.16 (Tele) (D/W) (tolerance +/-3%)
7 Throw Ratio
51”@ 2m & 60”@ 2.37m with zoom at wide
For X1326AWH
● 1.54 (Wide) ~ 1.72 (Tele) (D/W) (tolerance +/-3%)
60”@ 2m with zoom at wide
For 1126AH/ X1226AH
● f=21.85mm(Wide)~24.01mm (Tele) @ 60”
For X1326AWH
8 Projection Lens
● f=21.85mm(Wide)~24.00mm(Tele)
����������������������������������������
@ 60” WXGA
● F#=2.41(Wide)~2.53(Tele)
● 1.1X Mechanical Zoom Lens

X1126AH/X1226AH/X1326AWH Confidential 1-

No Item Description
Standards :
● NTSC (3.58/4.43)
9 Video Compatibility
● PAL (B/D/G/H/I/M/N)
● HDTV (480i,576i 480p, 576p, 720p, 1080i, 1080p)

10 System Controller ● Scaler:

����������������������
TI DDP4421 x 1

RGBCYW (normal Y44)--R78Y44G81C34W55B68

- URD20VA motor
11 Color Wheel - 6000 ~ 7650 rpm @ CW 2X and 1.5X (50 ~85Hz)
- 9000 rpm @ CW 3X (50Hz)
- 7200 rpm @ CW 1X (120Hz)

12 Lamp ● 220 Watt OSRAM E20.9 Lamp

Operation:
● 0 -- 2500 ft, 0 -- 40 °C
● 2500 -- 5000 ft, 0 -- 35 °C
13 Altitude
● 5000 -- 12000 ft, 0 -- 30 °C
Storage: -30°C ~ 65 °C
Maximum 40000 ft
● Hsync Frequency 15k -100kHz
● Vsync Frequency 24 ~ 120Hz
● Video Signal RGB(PC)
14 Input Signal Spec.
- Analog RGB 0.7Vp-p, 75 ohm, Separate TTL H,V Sync
- Analog RGB 1Vp-p, 75 ohm, Sync on Green singal.
- Composite video 1Vp-p, 75 ohm

Power ● Normal mode: 240W ± 10% @ 110VAC

15 ● ECO mode: 195W ± 10% @ 110VAC
Consumption ● Standby mode < 0.5W @ DC 5V out off

For 1126AH/ X1226AH

● Typical - 3500ANSI Lumens @ lamp power OD 220W
Minimum - 3200ANSI Lumens @ lamp power OD220W
16 Brightness
For X1326AWH
Typical - 3600ANSI Lumens @ lamp power OD 220W
Minimum - 3200ANSI Lumens @ lamp power OD220W
● 65% Japan standard (Minimum; Full power mode)
17 Uniformity ● 80% Japan standard (Typical; Full power mode)

X1126AH/X1226AH/X1326AWH Confidential 1-

No Item Description
18 Throw Distance ● 1.0m~11.8m
������������������������������������������������������������
(Focus range with optimized@ 2.3m throw distance)
Native mode:
● 1760:1 (Minimum)
- Full White with full power @ wide mode
- Full Black with eco power @ wide mode
● 2200:1
��������������������������������������
(Typical, for reference only))
- Full White with full power @ wide mode
- Full Black with eco power @ wide mode
APM mode:
● 1800:1
������������������������������������
(Minimum���������������������
, for reference only�)
19 Contrast - Full White with full power @ tele mode
- Full Black with eco power @ tele mode
● 3600:1
������������������������������������
(Typical, �������������������
for reference only�)
- Full White with full power @ tele mode
- Full Black with eco power @ tele mode
● 18000:1
��������������������������������������
(Typical, for reference only)
- Full White with full power @ tele mode
- Full Black with extreme-diming lamp power 30% @ tele mode
APM contrast ratio (at tele mode) = Native contrast ratio (at wide
mode) x APM factor 1.28
● 5,800
���������������������������������
hours typical (Normal mode)
● 6,000
������������������������������
hours typical (ECO mode)
22 Lamp Life ● 10,000
����������������������������������
hours typical (Dynamic Eco)
Definition of lamp life: 50% of lamps are still operational and still
have at least 40% of the original lumen output.

X1126AH/X1226AH/X1326AWH Confidential 1-

1-2 Compatible Mode

VGA Analog
(1) PC Signal
Compatibility Resolution V.Frequency [Hz] H.Frequency [KHz]
640x480 60 31.5
640x480 72 37.9
VGA 640x480 75 37.5
640x480 85 43.3
640x480 120 61.9
800x600 56 35.1
800x600 60 37.9
800x600 72 48.1
SVGA
800x600 75 46.9
800x600 85 53.7
800x600 120 77.4
1024x768 60 48.4
1024x768 70 56.5
XGA 1024x768 75 60.0
1024x768 85 68.7
1024x768 120 99.0
1152x864 70 63.8
1152x864 75 67.5
1152x864 85 77.1
SXGA 1280X1024 60 64.0
1280X1024 72 77.0
1280X1024 75 80.0
1280X1024 85 91.1
1280x960 60 60.0
QuadVGA
1280x960 75 75.2
SXGA+ 1400x1050 60 65.3
UXGA 1600x1200 60 75.0

X1126AH/X1226AH/X1326AWH Confidential 1-

(2) Extended Wide timing
Compatibility Resolution V.Frequency [Hz] H.Frequency [KHz]
1280x768 60 47.8
1280x768 75 60.3
1280x768 85 68.6
1280x720 60 44.8
WXGA 1280x720 120 92.9
1280x800 60 49.6
1280x800 119.909 101.6
*1920x1200 60 74
1440x900 60 59.9
1680x1050 60 65.3
WSXGA+ 1080P 60 67.5
1366x768 60 47.7
WUXGA 1920x1200-RB 59.94 74.04

(3) Component Signal

480i 720x480(1440x480) 59.94(29.97) 15.7
576i 720x576(1440x576) 50(25) 15.6
480p 720x480 59.94 31.5
576p 720x576 50 31.3
720p 1280x720 60 45.0
720p 1280x720 50 37.5
1080i 1920x1080 60(30) 33.8
1080i 1920x1080 50(25) 28.1
1080p 1920x1080 23.97/24 27.0
1080p 1920x1080 60 67.5
1080p 1920x1080 50 56.3

X1126AH/X1226AH/X1326AWH Confidential 1-

HDMI Digital
HDMI - PC Signal
Compatibility Resolution V.Frequency [Hz] H.Frequency [KHz]
640x480 60 31.5
640x480 72 37.9
VGA 640x480 75 37.5
640x480 85 43.3
640x480 120 61.9
800x600 56 35.1
800x600 60 37.9
800x600 72 48.1
SVGA
800x600 75 46.9
800x600 85 53.7
800x600 120 77.4
1024x768 60 48.4
1024x768 70 56.5
XGA 1024x768 75 60.0
1024x768 85 68.7
1024x768 120 99.0
1152x864 70 63.8
1152x864 75 67.5
1152x864 85 77.1
SXGA 1280X1024 60 64.0
1280X1024 72 77.0
1280X1024 75 80.0
1280X1024 85 91.1
1280x960 60 60.0
QuadVGA
1280x960 75 75.2
SXGA+ 1400x1050 60 65.3
UXGA 1600x1200 60 75.0

X1126AH/X1226AH/X1326AWH Confidential 1-

(2) Extended Wide timing
Compatibility Resolution V.Frequency [Hz] H.Frequency [KHz]
1280x768 60 47.8
1280x768 75 60.3
1280x768 85 68.6
1280x720 60 44.8
WXGA 1280x720 120 92.9
1280x800 60 49.6
1280x800-RB 119.909 101.6
1440x900 60 59.9
1920x1200 60 74
1680x1050 60 65.3
WSXGA+ 1080P 60 67.5
1366x768 60 47.7
WUXGA 1920x1200-RB 59.94 74.04

(3) HDMI-Video Signal

480i 720x480(1440x480) 59.94(29.97) 15.7
480p 720x480 59.94 31.5
576i 720x576(1440x576) 50(25) 15.6
480p 720x480 59.94 31.5
576p 720x576 50 31.3
720p 1280x720 60 45.0
720p 1280x720 50 37.5
1920x1080 60(30) 33.8
1080i
1920x1080 50(25) 28.1
1920x1080 23.98/24 27.0
1920x1080 60 67.5
1080p
1920x1080 50 56.3
1920x1200-RB 59.94 74.04

X1126AH/X1226AH/X1326AWH Confidential 1-

1-3 Product Overview

Projector Outlook

Item Description Item Description

1 Lamp cover 7 Focus ring Lamp cover

2 Air outlet Focus ring 8 Remote control receiver

3 Control panel Zoom ring 9 Projection lens

4 Power button 10 Lens cap

5 Zoom ring 11 Tilt adjusting wheels

6 Air inlet

X1126AH/X1226AH/X1326AWH Confidential 1-

Rear side

IO placement for X1126AH/X1226AH/X1326AWH

X1126AH/X1226AH/X1326AWH Confidential 1-

Item Description Item Description

1 Power socket 6 RS232 connector

2 HDMI 1/MHL connector 7 Kensington™ lock port
Composite video input
3 HDMI 2 connector 8 connector)
5V DC output connector
4 (device charge & support 9 Audio in connector
mouse page up/down function)
PC analog signal/HDTV/
5 component video input 10 Audio out connector
connector

X1126AH/X1226AH/X1326AWH Confidential 1-10

Control Panel

Item Icon Function Description

1 POWER POWER Power Indicator LED

2 LAMP LAMP Lamp Indicator LED

3 TEMP TEMP Temp Indicator LED

See the contents in “Turning the Projector On/
4 POWER
Off” section.
Four
5 Use to select items or make
directional
adjustments to your selection.
select keys
6 BACK BACK Returns to the previous operation.

7 SOURCE SOURCE Changes the active source.

8 ENTER ENTER Confirm your selection of items.

Adjusts the image to compensate for
9 Keystone
distortion caused by tilting the projector.
Press “MENU” to launch the Onscreen display
10 MENU MENU (OSD) menu, back to the previous step for the
OSD menu operation or exit the OSD menu.

X1126AH/X1226AH/X1326AWH Confidential 1-11

Remote Controller Layout

X1126AH/X1226AH/X1326AWH Confidential 1-12

Item Icon Function Description

1 Infrared transmitter Sends signals to the projector.

Refer to the “Turning the Projector
2 POWER
On/Off” section.

3 MUTE To turn on/off the volume.

4 RATIO To choose the desired aspect ratio.

Select/Enter Confirm your selection of items.

5
Play/Pause Press to begin/pause playback.
Use up, down, left, right buttons to
6 Four directional select keys select items or make adjustments to
your selection.

7 3D Press “3D” to select 3D models.

8 SOURCE Changes the active source.

Press “MODE” to select the display

9 MODE mode from Bright,Presentation,
Standard, Video and User.
Adjusts the image to compensate
10 KEYSTONE for distortion caused by tilting the
projector.

BACK Returns to the previous operation.

11
STOP Press to stop playback.
Press “VGA” to change source to
the VGA connector. This connector
12 VGA supports analog RGB, YPbPr
(480p/576p/720p/1080i), YCbCr
(480i/576i) and RGBsync.

13 FREEZE To pause the screen image.

For computer mode only. Use this

button to select the previous page. This
14 PgUp function is only available when USB
Ctrl connector (USB A) is onnected to a
computer via a USB cable.

X1126AH/X1226AH/X1326AWH Confidential 1-13

 Item Icon Function Description

15 COMPONENT No function.

For computer mode only. Use this

button to select the next page.This
function is only available when
16 PgDn
USB Ctrl connector (USB A) is
connected to a computer via a
USB cable.
Press “MEDIA” to return to the
17 MEDIA home page of media
mode.
Press “0~9” to input a password in
18 KeyPad 0~9
the “Security” OSD.
• Press “MENU” to launch the
Onscreen display (OSD) menu,
back to the previous step for the
19 MENU
OSD menuoperation or exit the
OSD menu.
• Confirm your selection of items.

20 HDMI™/MHL To change source to HDMI/MHL.

Momentarily turns off the video.

21 HIDE Press “HIDE” to hide the image,
press again to display the image.

22 ZOOM IN Zooms the projector display in.

To change source to COMPOSITE

23 VIDEO
VIDEO.

24 ZOOM OUT Zooms the projector display out.

Press “LAN/WiFi” to display the

image which is wire or wirelessly
25 LAN/WiFi transmitted from the PC to the
projector via the “Acer LAN
webpage management” utility.

26 Backlight Remote backlight.

X1126AH/X1226AH/X1326AWH Confidential 1-14

Getting Started
Connecting the Projector

X1126AH/X1226AH/X1326AWH Confidential 1-15

 Item Description Item Description

1 Power cord 7 Audio cable Jack/RCA

2 HDMI cable 8 Audio cable Jack/Jack
MHL cable (MicroUSB to
3 HDMI) 9 USB cable for charging device

4 VGA cable 10 RS232 cable

VGA to component/HDTV
5 adapter Composite video 11 USB cable for charging device
cable
6 3 RCA component cable 12

Note 1: To ensure the projector works well with your computer,please make sure the timing
of the display mode is compatible with the projector.
Note 2: Functions vary depending on model definition.
Note 3: USB cable needs powered extender if the length is over 5 m.
Note 4: Some smartphones require a converter (supplied by smartphone maker) to enable
the MHL function.
Note 5: USB DC 5V out connector support 5V/2.0A power output for power bank charging
only when MHL source is not detected.

X1126AH/X1226AH/X1326AWH Confidential 1-16

Bottom Cover Dimension

X1126AH/X1226AH/X1326AWH Confidential 1-17

Chapter 2

Disassembly & Assembly Process

2-1 Equipment Needed & Product Overview
1. Screw Bit (+): 105
2. Screw Bit (+): 107
3. Screw Bit (-): 107
4. Hex Sleeves 5mm
5. Long Nose Nipper
6. Tweezers
7. Projector
* Before you start: This process is protective level II.Operators should wear electrostatic chains.

X1126AH/X1226AH/X1326AWH Confidential 2-

2-2 Disassemble Lamp
Cover
1. Loosen 1 screw (as red circle) on the
Lamp Cover.

2. Disassemble the Lamp Cover Module.

Lamp Cover

2-3 Disassemble Lamp

Module
1. Tear off lamp mylar.
2. Loosen 1 screw (as yellow circle) on the
Lamp Module.
3. Take out the Lamp Module.

WEEE ANNEX VII PARTS.

Lamp

Lamp

X1126AH/X1226AH/X1326AWH Confidential 2-

2-4 Disassemble Top Cover
Module
1. Unplug Focus Ring.

Focus Ring

2.Unscrew 6 screws (as blue circle).

3. Remove the Top Cover Module.

Top Cover Module

X1126AH/X1226AH/X1326AWH Confidential 2-

4. Take out Keypad Rubber.(as red square)

5. Unscrew 1 screw to disassemble Zoom

Ring and Zoom Ring Holder(as blue
circle).

Top Cover Module Keypad Rubber

Zoom Ring Zoom Ring Holder

X1126AH/X1226AH/X1326AWH Confidential 2-

2-5 Disassemble Main Board

D
E
F

A B C

Please refer to the table as below for details of each connector.

Male Conector on
Item The key feature Figure
Main Board

Compose of Red/White/
A IR SENSOR
Black Wire (3 pin)

Compose of Red/White/
B Photo sensor board
Black Wire (3 pin)

Compose of Brown/
C System Fan
Blue/Black Wire (3 pin)

D LVPS Red wire tube (10 pin)

E LVPS Black wire tube (5 pin)

Compose of Red/Black
F Speaker
Wire (2 pin)

X1126AH/X1226AH/X1326AWH Confidential 2-

1. Unscrew 4 screws(as blue circle) and
disconnect all cables.

2. Unscrew 6 hex screws to disassemble

Main Board(as red circle).

3. Unplug 3 connectors(as red square).

4. Take out the RS232 cable and VGA out

cable.
RS232 cable

WEEE ANNEX VII PARTS. Main Board

Main Board
VGA out cable

X1126AH/X1226AH/X1326AWH Confidential 2-

5. Take out the Speaker(as red square).

6. Unscrew 4 hex screws to disassemble

Main Board Shielding(as red circle).
Speaker

MB Shielding

Rubber

2-6 Disassemble IO Cover

Module

1. Take out the IO Cover Module(as red

square).

IO Cover

X1126AH/X1226AH/X1326AWH Confidential 2-

2-7 Disassemble System
Fan

1. Unscrew 3 screws (as red circle) and

unplug 3 connectors to disassemble the
Lamp Housing.

2. Unscrew 2 screws(as blue circle) to

disassemble Lamp Wire and Interlock
Switch.

Interlock Switch Lamp Wire

X1126AH/X1226AH/X1326AWH Confidential 2-

3.����������������������������������
Unscrew 1 screw(as red circle) to
disassemble the System Fan.

4.����������������������������������
Unscrew 1 screw(as red circle) to
disassemble Thermal Switch.

Thermal Switch
Syatem Fan

Lamp Housing

Note: - Take the Fan Module as the right

gesture.

the right gesture the wrong gesture

X1126AH/X1226AH/X1326AWH Confidential 2-

2-8 Disassemble Engine
Module

1. Unscrew 6 screws (as blue circle) to

disassemble engine module.

2. Unscrew 2 screws (as blue circle) to

disassemble the Color Wheel Module.

3. Unscrew 3 screws (as red circle) to

disassemble the Color Wheel Module
and Photo Sensor Board.

Photo Sensor Board Color Wheel

4. Unscrew 2 screws(as yellow circle).

X1126AH/X1226AH/X1326AWH Confidential 2-10

5. Unscrew 3 screws (as yellow circle).

6. Rotate the screw (as yellow circle)

180° anticlockwise to disassemble
DMD Chip.

DMD Board DMD Chip

WEEE ANNEX VII PARTS.
DMD Board

DMD Rubber DMD Mask

X1126AH/X1226AH/X1326AWH Confidential 2-11

 Heatsink
Engine Module

2-9 Disassemble LVPS

1. Unscrew 2 screws to take out LVPS

Module(as red circle).

2. Unplug 2 connectors(as blue square).

3. Unscrew 5 screws to disassemble

LVPS(as red circle).

X1126AH/X1226AH/X1326AWH Confidential 2-12

 LAMP DRIVER LVPS TO MB
TO MB

MYLAR LVPS LVPS SHIELDING

WEEE ANNEX VII PARTS. LVPS

Capacitor

X1126AH/X1226AH/X1326AWH Confidential 2-13

2-10 Disassemble Bottom
Cover Module
1. Take out IR Sensor Board.

2.Unscrew 2 Adjust Foots.

3. Disassemble is complete.

IR SENSOR BOARD ADJUST FOOT

X1126AH/X1226AH/X1326AWH Confidential 2-14

2-11 Assemble Bottom
Cover Module
1. Screw 2 Adjust Foots.

ADJUST FOOT

2. Assemble IR Sensor Board.

IR SENSOR BOARD

X1126AH/X1226AH/X1326AWH Confidential 2-15

2-12 Assemble LVPS

1. Plug 2 connectors(as blue square).

2. Screw 5 screws to assemble

LVPS(as red circle).

LVPS TO MB LVPS TO MB

MYLAR LVPS LVPS SHIELDING

WEEE ANNEX VII PARTS.

1.Capacitor
LVPS

3. Screw 2 screws to assemble LVPS

Module(as red circle).

X1126AH/X1226AH/X1326AWH Confidential 2-16

2-13 Assemble Engine
Module

1.Rotate the screw (as yellow circle)

180°clockwise to assemble DMD Chip.

Engine Module Heatsink

WEEE ANNEX VII PARTS.

DMD Board
1.DMD Board DMD Mask

DMD Chip
DMD Rubber

X1126AH/X1226AH/X1326AWH Confidential 2-17

2. Screw 3 screws (as yellow circle).

3. Screw 2 screws (as red circle).

4. Screw 3 screws (as red circle) to

assemble the Color Wheel Module
and Photo Sensor Board.

Photo Sensor Board Color Wheel

X1126AH/X1226AH/X1326AWH Confidential 2-18

5. Screw 6 screws (as blue circle) to
assemble the Engine Module.

2-14 Assemble System Fan

1. Screw 2 screws(as red circle) to

assemble Lamp Wire and
Interlock switch.

Interlock Switch Lamp Wire

X1126AH/X1226AH/X1326AWH Confidential 2-19

2. Screw 1 screws(as red circle) to
assemble the System Fan.

3.��������������������������������
Screw 1 screw(as red circle) to
disassemble Thermal Switch.

Thermal Switch
Syatem Fan

4. Screw 3 screws (as red circle) and plug

3 connectors to assemble the Lamp
Housing.

X1126AH/X1226AH/X1326AWH Confidential 2-20

2-15 Assemble IO Cover
Module

1.Assemble the IO Cover Module(as red

square).

IO Cover

2-16 Assemble Main Board

1. Screw 4 hex screws to disassemble

Main Board Shielding(as red circle).

2. Assemble the Speaker(as red square). Speaker

MB Shielding

Rubber

X1126AH/X1226AH/X1326AWH Confidential 2-21

 RS232 cable

WEEE ANNEX VII PARTS.

1.Main Board
Main Board
VGA out cable

1. Plug 3 connector(as red square).

2. Screw 4 screws(as blue circle) and

disconnect all cables.

3.Screw 6 hex screws to disassemble

Main Board(as red circle).

X1126AH/X1226AH/X1326AWH Confidential 2-22

2-17 Assemble Top Cover
Module
1. Assemble Keypad Rubber.(as red square)

2. Screw 1 screw to disassemble Zoom

Ring and Zoom Ring Holder(as blue
circle).

Top Cover Module Keypad Rubber

Zoom Ring Zoom Ring Holder

3. Screw 6 screws (as blue circle).

X1126AH/X1226AH/X1326AWH Confidential 2-23

4. Plug Rocus Ring.

Focus Ring

2-18 Assemble Lamp Module

1. Tear off lamp mylar.
2. Loosen 1 screw (as yellow circle) on the
Lamp Module.
3. Take out the Lamp Module.

WEEE ANNEX VII PARTS.

Lamp

Lamp

X1126AH/X1226AH/X1326AWH Confidential 2-24

2-19 Assemble Lamp Cover
1. Loosen 1 screw (as red circle) on the
Lamp Cover.

2. Disassemble the Lamp Cover Module.

. Lamp Cover

X1126AH/X1226AH/X1326AWH Confidential 2-25

2-20 Rod Adjustment
1. Environment Adjustment
- The size of screen is 60.0''.
- This process should be done at a dark
environment.(under 2 Lux)
2. Procedure Adjustment
- Change
 the screen to "white screen".
- Adjust the screws by using the rod on
the engine module to readjust the image.
(Adjust "Screw 1" to fix "Up" & "Down"
screen yellowish or bluish and adjust
"screw 2" to fix "Right" &"Left" screen
yellowish or bluish.Adjust until the
yellowish or bluish parts disappeared )

2
3. Abnormal image inspection
- It should not have any abnormal color 1

at the frame of the image by estimating

through the eyes.
Note: - To avoid over adjusting the rod.
- After the opreation,please use the glue to
fix the screws.

X1126AH/X1226AH/X1326AWH Confidential 2-26

2-22 Repair Actions

Change Parts

Update Main System Color Lamp Engine

LVPS Fan
Board Firmware Wheel Module Module

Version Update V V
Color Wheel Index V V
PC Calibration V V
OSD Reset V V
EDID V
Re-write Lamp Hour
V V
Usage
Rod Adjustment V
Auto Waveform V V V
Fan Calibration V V V

X1126AH/X1226AH/X1326AWH Confidential 2-27

Chapter 3

Troubleshooting
3-1 LED Lighting Message

Lamp_LED Temp_LED Power LED

Message
Red Red Red Blue

Input Power Flash ON to Flash ON to Flash ON to

--
Plug OFF 100ms OFF 100ms OFF 100ms

Standby -- -- ON --

Power button
-- -- -- ON
ON

Lamp retry -- -- -- Quick Flashing

Power off
-- -- Quick Flashing --
(Cooling state)

Power button
OFF: Cooling
-- -- ON --
completed;
Standby Mode
Error (Thermal
-- ON -- ON
Failure)

Quick
Error (Fan lock) -- -- ON
Flashing

Error (Lamp
ON -- -- ON
breakdown)

Error (Color Quick

-- -- ON
Wheel Failure) Flashing

Note: No Light: "--"

X1126AH/X1226AH/X1326AWH Confidential 3-

3-2 Main Procedure

No Symptom Procedure

- Ensure the Power Cord and AC Power Outlet are securely

connected
- Ensure all connectors are securely connected and aren’t
1 No Power broken
- Check LVPS
- Check Main Board

- Check LED Status

a. Thermal Failure: Power Led light blue & Temp Led light
red
Fan
�������������������
Lock: Temp Led quick
����������������������������������
flash & Power Led light blue
- Execute
�����������������������������������������������
Auto Waveform and Fan Calibration������
- Check Fan
- Check Main Board
2 Auto Shut Down
b. Color wheel Failure: Lamp Led quick Flashing red��
&
Power Led light blue�
Lamp breakdown: Lamp Led light red & Power Led light
blue
- Check Lamp
- Check Color Wheel
- Check Photo Sensor
- Check Main Board

- Ensure all connectors are securely connected and aren’t

broken
- Check Lamp Cover, Intelock Switch
- Check Lamp Module
3 No Light On
- Check LVPS
- Check Main Board
- Check Color Wheel
- Check Photo Sensor Board

X1126AH/X1226AH/X1326AWH Confidential 3-

No Symptom Procedure
- Ensure the Signal Cable and Source work
(If you connect multiple sources at the same time, use the
"Source" button switch)
- Ensure all connectors are securely connected and aren’t
broken
4 No Image - Check Main Board
- Check DMD Board
- Check DMD Chip
- Check Color Wheel
- Check Engine Module
- Check Color Wheel
5 Mechanical Noise
- Check Fan Module
- Check if the Main Board and the Engine module are
assembled properly
6 Line Bar/Line Defect - Check Main Board
- Check DMD Board
- Check DMD Chip
- Do "Reset (All data)" of the OSD Menu
- Ensure that the signal cables and source are work as well
- Execute Auto Waveform and Fan Calibration
- Check Lamp Module
7 Image Flicker
- Check Color Wheel
- Check Photo Sensor and clean Photo Sensor
- Check Main Board
- Check DMD Board
- Do "Reset (All data)" of the OSD Menu
- Adjust Color Wheel Index
8 Color Abnormal - Check Main Board
- Check DMD Board
- Check Color Wheel

X1126AH/X1226AH/X1326AWH Confidential 3-

No Symptom Procedure
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
Poor Uniformity/ - Ensure the Brightness is within spec
9
Shadow
- Check rod alignment
- Check Engine Module
- Ensure the projection screen without dirt
- Ensure the projection Lens is clean
Dead Pixel/Dust - Clean DMD Chip and Engine Module
10
(Out of spec.)
- Check DMD Chip
- Check Engine Module
- Ensure that the signal cables and source work as well
11 Garbage Image - Check Main Board
- Check DMD Board
- Remote Controller
a. Check Battery
Remote Controller
12 b. Check Remote Controller
Failed
c. Check IR Sensor Board
d. Check Main Board
- Do "Reset (All data)" of the OSD Menu
13 Function Abnormal
- Check Main Board
-��������������������������������������������������������������������
Ensure the using 3D glasses is good and you must face the
projection.
- Ensure the signal source is 3D format.
14 3D Image Abnormal
- Ensure the 3D function of projector OSD is on and 3D sync
invert is on.
- Check Main Board.

X1126AH/X1226AH/X1326AWH Confidential 3-

No Symptom Procedure
-�������������������������������������������������������
An unique Universal Password which is printed on the
Security Card. This unique password is a back door of
Administrator Password which will be accepted by projector
anytime no matter what the Administrator Password is.
- If you forget the Password, please do the following steps to get
the Universal Password:
(1) Click the "AcerSNID"

(2) Input SNID number. (SNID number is on the Security Card)

Forgetting Password
15 (administrator
Password)

(3) Click "Calculate". Then the Universal Password will appear.

-��������������������������������������������������������
Please confirm whether the SNID number of Service Mode
is the same as the SNID number on the backside of projector?
- If not, please do the actions as below:
Universal Password
16 a. Execute the EDID Upgrade Procedure (refer to Chapter 6)
Failure
b. Press "Power", "Left", "Left" and "Menu" buttons sequentially
on remote controller to get into Service Mode to obtain the
SNID number, then calculate the Universal Password.

X1126AH/X1226AH/X1326AWH Confidential 3-

Chapter 4

Test & Inspection

4-1 Test Equipment Needed
- PC support HDTV resolution & Independent graphic card
- Blue-ray DVD player support “S-Video”,“3D source files”,”HDMI” and “Video”
- CL200A
- Quantum Data 802T or CHROMA2327 (Color Video Signal & Pattern Generator)

4-2 Test Condition

- Circumstance brightness: Dark room less than 2.0 lux.

- Product must be warmed up for 3 minutes. `

- Screen size: 60''

Screen Defects (While replacing DMD Chip,Main Board)

< Figure: ZoneA&Frame (as green line) Definition. >

X1126AH/X1226AH/X1326AWH Confidential 4-

4-3 Auto Waveform and Fan Calibration
Picture A
1. Hold “Enter” button and plug the power cord.
2. First the power LED flashes blue and red, after about 3 seconds, the
power LED will flash blue, when the power LED only flash red, release
the “Enter” button.
3. The screen will show “Saving Factory Fan RPM, please wait...Warning:
DO NOT unplug while the projector fan is running “(as Picture A shows)
4. After about 60 seconds,the projector will turn on automatically.
5. Get into Service Mode to check the “Factory Fan RPM” has been restored
(as Picture B shows)
6. The procedure is completed.
Note: -This step must be executed after changing FW,Main Board ,or
Fan.
. -The Factory Blower RPM value is about 2000~2500

4-4 Calibration

1. PC Calibration
Procedure - Test equipment: video generator
- Once Main Board is changed. PC Calibration
should be done as well.
(1) Test signal analog: 1280x800@60HZ
(2) Test Pattern: 16GRAY
16GRAY

- Note
(1) Calibration pattern should be in full screen

(2) Please press "Power", "Left", "Left" and

"Menu" buttons sequentially to get into Service
Mode.

X1126AH/X1226AH/X1326AWH Confidential 4-

 (3) Choose "Analog Settings", select "PC Calibration"
and press “Enter” button. When the message
“Success” appears, it means “PC Calibration”
is OK. Choose “Return to Service Menu” to leave
service mode.

Check pattern - Test signal: 800 x 600 @60Hz

- Test pattern: 64 gray RGBW
* After finishing PC calibration,check 64 gray
RGBW pattern.
Inspection item - Color saturation

Criteria - There should not have any lack of RGBW.The 64 gray RGBW
color should appear normal and sort in right order.
- Color levels should be sufficient and normal. (the
unidentified color levels on both left and right sides
should not over 8 color levels.)

2. Color Wheel Index Adjustment

Check pattern - Test signal: 800 x 600@60HZ

Test pattern: 64 gray RGBW

Procedure - Test equipment: video generator

- Please press “Power”, “Left”, Left” and “Menu”

buttons sequentially to get into Service Mode.

-Adjust “CW Index” to correct the test pattern.

64 gray RGBW
Inspection item - Color saturation

Criteria - There should not have any lack of RGBW.

- Color levels should be sufficient and normal.

X1126AH/X1226AH/X1326AWH Confidential 4-

3. G Sensor Index

Procedure - Please put the Projector on a horizontal surface.

- Please press “Power”, “Left”, “Left” and “Menu”

buttons sequentially to get into Service Mode.

- Choose “G Sensor Index” and press “Enter“

button.

Note: G Sensor Index value:-10~10

X1126AH/X1226AH/X1326AWH Confidential 4-

4-5 I/O Port Test

4-5-1 VGA Port Test

Note: - When getting into function test,adjust the zoom ring and focus ring
to guarantee the image maximum and clearest,then start to test.

1. Frequency and tracking boundary

Procedure - Test equipment: video generator
General-1
- Test signal: analog 800 x 600@60HZ
- Test pattern: general-1 or master
- Check and see if the image sharpness is well per-
formed.
- If not,re-adjust by the following steps:
(1) Select "Frequency" function to adjust the total pixel
number of pixel clock in one line period. Master
(2) Select "Tracking" function and use right or left
arrow key to adjust the value to minimize video
flicker.
- Adjust Resync or Frequency/Tracking/H Image Shift/V
Image Shift to the inner screen.

Inspection item - Eliminate visual wavy noise by Rsync, Frequency

or Tracking selection.
- Check if there is noise on the screen.
- Horizontal and vertical position of the video should be
adjustable to the screen frame.

Criteria - If there is noise on the screen, the product is consid-

ered as failure product.
- If there is noise on the screen,use auto or manual
“frequency” function or “tracking” function to adjust the
screen.
- The PC mode functionally sure be workable include
support format with frequency and auto detected func-
tional will be workable.

X1126AH/X1226AH/X1326AWH Confidential 4-

2. Bright Pixel
Procedure - Test equipment: video generator
- Test signal: 800 x 600@60HZ
Gray 10
Inspection item - Bright pixel check.
Criteria - Please refer to Pixel specification table.

3. Dark Pixel
Procedure - Test equipment: video generator.
- Test signal: analog 800 x 600@60HZ Full white
- Test Pattern: full white
Inspection item - Dead pixels check.
Criteria - Please refer to Pixel specification table.

4. Bright Blemish
Procedure - Test equipment: video generator.
- Test signal: analog 800 x 600@60HZ Gray 10
- Test Pattern: gray 10
Inspection item - Bright blemish check.
Criteria - Please refer to Pixel specification table.

5. Dark Blemish
Procedure - Test equipment: video generator.
- Test signal: analog 800 x 600@60HZ
Blue 60
- Test Pattern: blue 60
Inspection item - Dark blemish check
Criteria - Please refer to Pixel specification table.

X1126AH/X1226AH/X1326AWH Confidential 4-

Defect specification table

Order Symptom Pattern Criteria

1.≤ 8 visible light blemishes are
1 Light blemish Gray 10
allowed in the active area

1.≤ 8 visible dark blemishes are

2 Dark blemish Blue 60
allowed in the active area

1.Eyecatcher and border artifacts

3 Eyecatchers Border Artifacts Black
are allowed

1. No adjacent pixels
1. Any screen 2. No bright pixels in active area
2. Gray 10 3. No unstable pixels in active
area
3. Any screen
4. ≤ 1 bright pixel in the POM
4. Gray 10
4 Projected Images 5. ≤ 3 dark pixels in the active
5. White
area
6. Any screen
6. No DMD window aperture
7. Black or White shadowing on the active area

8. Any screen 7. Βlemishes are allowed

8. Mottling is allowed

6. Focus test
Procedure - Test equipment: video generator
- Test signal: analog 800 x 600@60HZ
- Test pattern: Full screen
Inspection item - Focus check
Criteria -Look at the entire screen, focus shall be clear, crisp,
and sharp over the entire surface of the display pat-
tern. (Blur word on one of the corner after adjustment
is acceptable. However, the word should at least be
recognizable.)

Full screen

X1126AH/X1226AH/X1326AWH Confidential 4-

4-5-2 Audio Test
Procedure - Test equipment: DVD Player & Speaker box
- Test signal: CVBS
Inspection item - Audio performance test
Inspection Size - 60’’
Criteria - Check the sound from speaker
- Plug Audio cable into Audio In port and connect speak-
er box into audio out,check if "Volume" is normal.
- Adjust the volume to maximum by using the
remote controller.
- Check the sound from speaker and speaker box
- Check if the "Mute" is normal.

4-5-3 Video Port Test

Procedure - Test equipment: DVD player
- Test signal: Video
Inspection item - Video performance test
Criteria - Check any abnormal color,line distortion
or any noise on the screen.
- Check the sound from speaker.

4-5-4 HDMI Port Test

Procedure - Test equipment: DVD Player with
HDMI output.
- Test signal: 1080p@60 Hz
Inspection item - HDMI performance test.
Criteria - Ensure the image is well performed
and the color can not discolor.

X1126AH/X1226AH/X1326AWH Confidential 4-

4-6 Optical Performance Measure

Inspection Condition
- Environment luminance: 0.03 Lux
- Product must be warmed up for 3 minutes
- Screen Size: 60''

1. Test equipment
Procedure - Connect VGA IN port of Projector with VGA port
of Chroma by VGA cable, press "Menu" button,get
into OSD mode, the settings are as below:
- "Display mode" is "Bright",the "Format" is "16:9" and
“ECO Mode” is “Off”.

2. Brightness
Procedure - Full white pattern
- Use CL200A to measure brightness values of P1~P9
- Follow the brightness formula to calculate
brightness values. Full white pattern

☼ Brightness Formula
Avg. (P1~P9)*0.99m2

Criteria ● 1925 ANSI lumen

X1126AH/X1226AH/X1326AWH Confidential 4-

3. Full On/Full Off Contrast

Procedure - Full white pattern & full black pattern

- Use CL200A to measure brightness values of full
white pattern P5 & full black pattern B5
- Follow Contrast formula to calculate contrast values.
☼ Contrast Formula

P5/B5
Note: P5
��� ��
= ������������������������������������
Lux of center in full white pattern
Full black pattern
B5 =Lux of center in full black pattern
Criteria ���������
● 1800:1

4. Uniformity�
Procedure - Full white pattern
- Use CL200A to measure brightness values of
P1~P9 (see image: full white).
- Follow the Uniformity formula to calculate
average values.
☼ Uniformity Formula

JBMA Uniformity = Avg. (P1, P3, P7, P9)/P5 X100% Full white pattern

Criteria ● 65%

4-7 Burn in Test

- Temperature: 15~40 °C
- Screen size: No concern
- After repairing each unit, it should be Burn in(refer to the below table).

X1126AH/X1226AH/X1326AWH Confidential 4-10

 Symptom Run-in Time
Normal repair 2 hours
NFF 4 hours
Auto shutdown 6 hours
- Get into Burn-In Mode
* Cycle setting is based on the defect symptoms. ie: If it is NFF,the run-in time is 2 hours.You have
to set the lamp on for 30 min.and lamp off for 10 min for 4 cycles.

Press Power→ Left → Left → Menu on remote controller or keypad button.

Choose Burn In > enter
Lamp On (Min) Press right key to adjust the time (30)
Lamp Off (Min) Press right key to adjust the time (10)
Set Burning cycle Press right key to adjust the cycle
After setting up the time, choose ''Enter into Burn In Mode'' and press "Menu" button.
Note:During Brun in test,if you want to end the process,please enter "Power" button.

4-8 Test Inspection Procedure

1. Check points for exterior and print pattern

Check item Check point
Missing letters & pattern or blurry prints are
Text & Pattern
unacceptable.
Dirt, scrape, water ripples and uneven color are
Exterior
unacceptable.
Focus ring Focus ring is functioning smoothly.
Missing logo, missing prints and blurry prints are
Logo
unacceptable
Screw All screws should be fixed and in right type.
Pedestal Well-functioned
Lamp Cover It should be locked in the correct place.
Plastic Parts All plastic parts can not be broken and damaged.
Safety or warning All safety and warning labels should be visible,
label including all contents.
All interface connectors should be complete and
Connector
workable.

X1126AH/X1226AH/X1326AWH Confidential 4-11

2. OSD Reset
1. After final QC step, we have to erase all saved change again and
restore the OSD default setting. The following actions will allow you
to erase all end-users’ settings and restore the default setting:
(1) Please get into OSD menu.
(2) To execute “Reset” function.

X1126AH/X1226AH/X1326AWH Confidential 4-12

4-9 Re-write Lamp Usage
Hour
1. Get into Service Mode
- Press "Power", "Left", "Left" and "Menu"
buttons sequentially to get into Service
mode.
2. Get into Other Settings Mode
- Use "Up" or "Down" buttons to select
"Other Settings", then press "Enter"
button.
3. Re-write System Hours
- Select "System Hours " and use
"Left" or "Right" buttons to re-write the
"System Hours ".

4. Re-write Lamp Full Hours

- Select "Lamp Full Hours "and use
"Left" or "Right" buttons to re-write the
"Lamp Full Hours ".
5. Re-write Lamp ECO Hours
- Select "Lamp ECO Hours " and use
"Left" or "Right" buttons to re-write the
"Lamp ECO Hours".
6. Re-write Lamp ED Hours
- Select "Lamp ED Hours " and use
"Left" or "Right" buttons to re-write the
"Lamp Dynamic Hours".
7. Exit Service Mode
- Use "Up" or "Down" buttons to select
"Exit", press "Enter" button to exit the
Service Mode.
Note: left key = decrease System/Lamp hour
right key =increase System/Lamp hour

X1126AH/X1226AH/X1326AWH Confidential 4-13

Chapter 5

Firmware Upgrade
Section 1:System Firmware Upgrade

5-1-1 Equipment Needed

Software:

- DLP Composer Lite 11.2

- Firmware (*.img)
- FlashDeviceParameters-20141125.zip
Note: - Please download "DLP Composer Lite 11.2" and "FlashDeviceParameters-20141125.zip"
from website to upgrade FW procedure.

Hardware:
- Projector
- Power cord: 42.50115G001
- USB A to A: 42.0028JG001
- PC or Laptop

X1126AH/X1226AH/X1326AWH Confidential 5-

5-1-2 DLP Composer Lite
Setup Procedure
1. Choose "DLP Composer Lite 11.2 Setup"
Program.

2. Click "Next".

3. Read "License Agreement".

-C
 hoose "I accept and agree to be bound
by all the terms and conditions of this
License Agreement".
- Click "Next".

4. Click "Next".

X1126AH/X1226AH/X1326AWH Confidential 5-

5. Click "Next".

6. Click "Next".

7. The program is executing "installing"

status.

8. Click "Finish".

X1126AH/X1226AH/X1326AWH Confidential 5-

5-1-3 USB Driver Upgrade
Procedure

1. Set-up

- Connect projector with PC by USB cable.

2.Click "Start" on PC screen,click "Install DLP

Device Driver"

3.Select "Microsoft WinUsb",click"Install"

X1126AH/X1226AH/X1326AWH Confidential 5-

4.Click "Next"

5.On install processing

6.Click "Finish",USB driver set up procedures

are completed

Note: - If you have installed the USB driver,there

is no need to perform this action.

X1126AH/X1226AH/X1326AWH Confidential 5-

5-1-4 Firmware Upgrade Procedure
1. Set-up

-H
 old on "Power" and "Enter" buttons and plug in
the power cable.Until the "Power","Temp","Lamp"
Leds steady light red,then release the "Power" and
"Enter" button.

2. Execute the "DLP ComposerTM Lite 11.2" file.

3. Setting "FlashDeviceParameters".
-S
 elect the file "FlashDeviceParameters".
- Put "FlashDeviceParameters"file
into the folder where you setup "DLP Composer
Lite 11.2".

4. Click "Edit" and "Perferences".



5. Click "Communications".

X1126AH/X1226AH/X1326AWH Confidential 5-

 - Select "USB"

- Click "OK".

6. Choose "Flash Loader".

-C
 lick "Browse" to search the firmware file
(*.img).
- Click "Open".

7. Select "Complete Image Download", don't

select "Skip Boot Loader Area"

-Click "Reset Bus" to erase the flash

memory.

X1126AH/X1226AH/X1326AWH Confidential 5-

8. If the FW is ready,click "Start Download" to
execute the firmware upgrade.
- Click "Yes".

9. It takes about several minutes, the

firmware upgrade process is finished,
"Download complete" will appear on the
screen.
-U
 nplug USB cable and power cord.

10. Check System FW version. 

- Re-plug in power cable,then restart the
unit and get into the Service Mode to
check the system firmware version.
( To get into Service Mode, please press
"Power", "Left", "Left" and "Menu" buttons
sequentially on remote controller or keypad
button.)

X1126AH/X1226AH/X1326AWH Confidential 5-

Section 2:MCU Firmware Upgrade

5-2-1 Equipment Needed

Software:

- Make sure upgrade the latest system FW firstly.

Hardware:
- Projector
- Power cord: 42.50115G001

X1126AH/X1226AH/X1326AWH Confidential 5-

5-2-2 Upgrade MCU firmware

1. Hold on “Enter” key, then plug in the power

cord. About 1sec, release “Enter” key when
power led flashing red and blue.

2. Press "Enter" key when power led flashes

blue and lamp/temp leds flash red.

3. Then the power led lights blue and temp/lamp

leds flash red fastly, it means that the program
is downloading.

4. Waiting for power led lights red, and temp/lamp

leds don't light, the projector return to standby
mode, the download program was completed.

5. Check MCU FW version. 

- Re-plug in power cable,then restart the unit
and get into the Service Mode to check the
MCU firmware version.
( To get into Service Mode, please press "Power",
"Left", "Left" and "Menu" buttons sequentially on
remote controller or keypad button.)

X1126AH/X1226AH/X1326AWH Confidential 5-10

Chapter 6

EDID Upgrade
6-1 EDID Introduction
Extended Display Identification Data is a VESA standard data format that contains basic
information about a display device and its capabilities, including vendor information,
maximum image size, color characteristics, factory pre-set timings, frequency range limits,
and character strings for the monitor name and serial number.
The information is stored in the display and is used to communicate with the system
through a Display Data Channel (DDC), which sites between the display device and the
PC graphics adapter. The system uses this information for configuration purposes, so the
monitor and system can work together.

Note: - If a display device has digital input ports, like DVI or HDMI, but without EDID in its Main
Board, the display device will show no image while the input source is digital signal.

X1126AH/X1226AH/X1326AWH Confidential 6-

6-2 Equipment Needed

Software

- EDID Program
- EDID File (*.ini)

Hardware

- Projector
- Power Cord for Projector (42.00126G001)
- Power Adaptor for Projector(47.8PK01G001)
- VGA cable(42.0020HG001)
- Power Adaptor (47.57803G001)
- Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed)
- RS-232 9 Pin Cable (pin to pin, F-M)
- PC and Monitor

X1126AH/X1226AH/X1326AWH Confidential 6-

6-3 Setup Procedure
1. Setup
- Hold on "Power" and "Enter" buttons, then plug in
Power adapter to projector. Release the "Power" and
"Enter" buttons when "Power" ,"Temp" and "Lamp"
LEDs light red.

2. Connect all ports

(1) Connect P1 of fixture to COM Port of
PC/Laptop by RS232 Cable. P2
VGA Cable
(2) Connect P2 of fixture to VGA IN 1
Port of projector by VGA Cable.
P5 RS232 Cable
(3) Connect P5 of fixture to VGA IN 2 VGA Cable
Port of projector by VGA Cable. P1
JP3
(4) Connect P3 of fixture to DVI
Port of projector by HDMI Cable . HDMI Cable
(5) Plug Power Adapter to P4 of fixture. P3 Adapter
P4

Note: - You must confirm that the JP3 is closed in

all procedure.

X1126AH/X1226AH/X1326AWH Confidential 6-

6-4 EDID Key-In Procedure
(VGA
����� ��
& �����
HDMI �)

1. Execute EDID Program

- Double click "EDID" to execute EDID

program.

2. Process
(1) Select the COM Port which you are
using.
(2) Click "Model".

(2)

(3) Select the EDID file (*.ini).

(4) Click "Open". (1)

(5) Key in the Serial Number into the

Barcode blank space. (3)

(6) In "Write Source Select" item, select (4)

"VGA1" and "HDMI1".
(7) Click "Program".

(5)

(7)

(6)

X1126AH/X1226AH/X1326AWH Confidential 6-

3. - When the message "Please change the
cable to VGA1" appears on the screen,
click "OK".

4. - When the message "Please change the

cable to HDMI1" appears on the screen,
click "OK".

5. When the EDID program is completed, a

message "OK" will appear on the screen.

6. Read EDID "Analog" information

- In "Read item", select "Analog" and
"Trans", then click the "Read".
- EDID "Analog" information will show the
result.

X1126AH/X1226AH/X1326AWH Confidential 6-

6. Read EDID "HDMI" information
- In "Read item", select "Digital" and "Trans",
then click the "Read".

- EDID "Digital" information will show the result.

X1126AH/X1226AH/X1326AWH Confidential 6-

Appendix A (Exploded Image)
Note: This chapter is only designed to show the exploded image of the projector.For updated part
numbers,please refer to RSPL report. Here we take U5230 for example.

DC
1

10 7

11
9

U5230/U5330W/U5530 
 Parts
Item P/N Description
Supply

1 51.71J02H001 LAMP COVER V

2 SP.7EB01GC01 ASSY LAMP MODULE FOR PROJECTOR V

3 70.78T06GR01 ASSY COVER TOP MODULE V

4 70.7EB06GR01 MAIN BOARD V

5 49.70U02G001 BLOWER V

6 70.71K15GR01 ASSY ENGINE MODULE (SERVICE) V

7 75.8ZZ02G131 ASSY COVER FRONT MODULE V

8 49.70U01G001 AXIAL FAN V

9 51.8ZC20H001 COVER 8ZZ RIGHT V

10 51.8ZC21H001 COVER 8ZC LEFT V

11 70.7EB05GR01 ASSY IO COVER MODULE SERVICE) V

U5230/U5330W/U5530 II
ASSY BOTTOM COVER MODULE

U5230/U5330W/U5530 III
 Parts
Item P/N Description
Supply

1 49.70U02G001 BLOWER V

2 49.72701G001 SPEAKER V

3 75.8PEP1G002 LVPS V

4 75.8TN01G002 LAMP DRIVER V

U5230/U5330W/U5530 IV
ASSY COLOR WHEEL MODULE

Parts
Item P/N Description
Supply

1 80.8VH04G002 PHOTO SENSOR BOARD V

2 70.8ZY17GR01 COLOR WHEEL MODULE V

U5230/U5330W/U5530 
ASSY PCBA MODULE

Parts
Item Description
Supply

1 70.7EB06GR01 MAIN BOARD V

2 70.7EB07GR01 IO BOARD V

3 70.7EB08GR01 LAN BOARD V

4 70.7EB09GR01 DAUGHTER BOARD V

S560P/S560T VI
FRU list
ACER PART
Category Core P/N ACER Desc Photo
NO.

CASE/COVER/
1 BRACKET ASSEM- 42.JPVJ2.004 75.7AR03G001 LENS CAP
BLY

CASE/COVER/
2 BRACKET ASSEM- 60.JPVJ2.008 70.7B923GR01 LAMP COVER
BLY

Acer Lamp
Module OS-
3 OPTICAL DEVICE MC.JQH11.005 SP.7C501GC01
RAM 220W
E20.9

CASE/COVER/
4 BRACKET ASSEM- 42.JPVJ2.002 51.7B904H001 RING FOCUS
BLY

CASE/COVER/
5 BRACKET ASSEM- 60.JPVJ2.001 51.7AR05H011 KEYPAD
BLY

CASE/COVER/
6 BRACKET ASSEM- 42.JPVJ2.003 51.8VH12H061 RING ZOOM
BLY

CASE/COVER/
RING ZOOM
7 BRACKET ASSEM- 42.JPVJ2.001 51.7AR15H001
HOLDER
BLY

CASE/COVER/
8 BRACKET ASSEM- 60.JPVJ2.006 70.7B922GR01 TOP COVER
BLY

X1126AH/X1226AH/X1326AWH Confidential 
 Acer
9 BOARD 70.7B956GR01 X1326AWH
Main Board

FAN SINK/SPEAK/
10 23.JMWJ2.001 49.72K01G001 SPEAKER
EARPHONE/RTC

SPEAKER
11 MISCELLANEOUS 47.JPVJ2.004 52.7AR02G001
RUBBER

CASE/COVER/
12 BRACKET ASSEM- 33.JPVJ2.002 61.7B901G001 MB BRACKET
BLY

CASE/COVER/
IO COVER
13 BRACKET ASSEM- 70.7B955GR01
X1326AWH
BLY

FAN SINK/SPEAK/
14 23.JP9J2.001 49.72J01G001 AXIAL FAN
EARPHONE/RTC

INTERRUPT
15 CABLE 47.JK6J2.001 75.87U02G101
SWITCH

CABLE LAMP
16 CABLE 42.0043EG067 DRIVER TO
LAMP

CASE/COVER/
LAMP HOUS-
17 BRACKET ASS 60.JPVJ2.004 51.7B902G001
ING
EMBLY

X1126AH/X1226AH/X1326AWH Confidential 
 COLOR
18 OPTICAL DEVICE 57.JJUJ2.001 70.8ZQ09GR01
WHEEL

PHOTO SEN-
19 BOARD 55.JK0J2.002 80.8YB05G001
SOR BOARD

CASE/COVER/
LAMP MOD-
20 BRACKET ASSEM- 33.JPHJ2.003 61.8VH09H001
ULE BRACKET
BLY

CASE/COVER/
HEAT SINK
21 BRACKET ASS 60.JQ9J2.003 61.74701H041
X1326AWH
EMBLY

DMD thermal
22 MISCELLANEOUS 47.JP9J2.001 52.72001G001
pad

DMD RUBBER
23 MISCELLANEOUS 47.JMXJ2.001 52.8CP01H021
X1326AWH

DMD CHIP
24 OPTICAL DEVICE 57.J940H.001 48.8EJ01G007
X1326AWH

DMD BOARD
25 BOARD 55.JQ8J2.001 80.7BK02G001
X1326AWH

ENGINE MOD-
26 OPTICAL DEVICE 57.JQ9J2.001 70.7BK09GR01
ULE

CABLE MB TO
27 CABLE 50.JH0J2.002 42.0045GG102
LVPS

X1126AH/X1226AH/X1326AWH Confidential 
 CABLE LAMP
28 CABLE 50.JPWJ2.003 42.00478G041 DRIVER TO
MB

Acer AIO Power

board (Power
29 BOARD MC.JQF11.002 75.7C501G001
+ Ballast) for
X1326AWH

CASE/COVER/
LVPS SHIELD-
30 BRACKET ASSEM- 33.JPVJ2.001 61.7AR01G001
ING
BLY

CASE/COVER/
31 BRACKET ASSEM- 47.JQFJ2.001 51.7C503G001 MYLAR LVPS
BLY

IR SENSOR
32 BOARD 55.JG5J2.003 80.88N05G001
BOARD

CASE/COVER/
BOTTOM
33 BRACKET ASSEM- 70.7B954GR01
COVER
BLY

CASE/COVER/
34 BRACKET ASSEM- 47.JPVJ2.001 52.8VH06H001 ADJUST FOOT
BLY

SCREW ISO
35 SCREW 86.JMFJ2.003 85.1C123G060
M3*6mm

SCREW M=2.6
36 SCREW 86.JMWJ2.002 85.3A126G060 D=2.48-2.58
L=6.0

SCREW PAN
37 SCREW 86.JMFJ2.004 85.WA123G100
TAP M3*10 Ni

SCREW HEX
38 SCREW 86.JPVJ2.001 61.71P07H011 M3 M2.6
H31.7mm

SCREW
39 SCREW 86.JMFJ2.005 85.WA126G060
M2.6*6

X1126AH/X1226AH/X1326AWH Confidential 
 SCREW
40 SCREW 86.JMWJ2.001 85.WA126G080
M2.6*8

POWER CORD
41 POWER CORD 27.J790H.001 42.00102G000
US & MEXICO

Acer Remote
REMOTE CON- Controller J3 25
42 MC.JPQ11.003 45.7AR01G001
TROLLER key with laser /
White

43 SCREW 47.JM4J2.014 61.8CP15H001 SPRING

44 SCREW 47.JM4J2.013 61.8CP16H001 STEP SCREW

45 CABLE 50.JQFJ2.002 43.7C917G001 SWITCH

46 CABLE 50.JMWJ2.001 42.004E7G021 RS232

VGA OUT TO
47 CABLE 50.JP9J2.002 42.006EVG001
MB

X1126AH/X1226AH/X1326AWH Confidential 
Appendix B
I. Serial Number System Definition

Serial Number Format for Projector

MRJR911001 838 01299 59 00

1 2 3 4 5

1 : MRJR911001 = Part Number of X1326AWH

2 : 838 = Date Code (ex:2018 = 8, the 38 week of the year = 38)

3 : 01299 = Serial Numbers

4 : 59 = Manufacturing Code (59 For China)

5 : 00 = For main part change or follow customer request

EX: MRJR911001838012995900
This label represents the serial number for X1326AWH.It is produced at CPC on 38 week
of 2018.Its serial code is 01299.

X1126AH/X1226AH/X1326AWH Confidential I
II. PCBA Code Definition

PCBA Code for Projector

A B XXXXXXXXXXX C XXX EEEE

1 2 3 4 5 6

1 : ID

2 : Vendor Code

3 : P/N
���

4 : ���
MB version
�������

5 : ����������
Date Code�

6 : ���
S/N

X1126AH/X1226AH/X1326AWH Confidential II
Appendix C
Equipment Needed For RS232 Function Test

Software:

- Docklight168.exe
- acer_RS232.ptp

Hardware:

- Projector
- RS-232 9 Pin Cable (pin to pin,F-M) (42.83C07G001)
- PC

X1126AH/X1226AH/X1326AWH Confidential 
Hardware Setup Procedure:

1.Connect projector RS232 port to COM Port of PC/

Laptop by RS232 Cord.

2.Plug in Power Cord.

Docklight168 Setup Procedure:

1.Double click the Docklight168 icon

2.Click “OK”.

X1126AH/X1226AH/X1326AWH Confidential 
3.Choose “Open an existing Docklight project (.ptp)
file” ,then click “Continue”.

4.Browse “acer_RS232.ptp”,then click “Open”.

5.Double click “Com 1”.

X1126AH/X1226AH/X1326AWH Confidential 
6.Select “Com” as what you connected,others
setting just as right picture shown.

7. After setup these procedures,RS232 commands

can be used by computer.

X1126AH/X1226AH/X1326AWH Confidential 
RS232 Protocol Communication Settings

Connection setting Value

Baud Rate 9600

Data Bits 8

Parity None

Stop Bits 1

X1126AH/X1226AH/X1326AWH Confidential 
RS232 function command summary table

General command type (Projector "receives�����������

"����������
commands)

No Code (character) Function feature

1 OKOKOKOKOK\r Power On
2 * 0 IR 001\r Power On
3 * 0 IR 002\r Power Off
4 * 0 IR 004\r Keystone
5 * 0 IR 006\r Mute
6 * 0 IR 007\r Freeze
7 * 0 IR 008\r Menu
8 * 0 IR 009\r Up
9 * 0 IR 010\r Down
10 * 0 IR 011\r Right
11 * 0 IR 012\r Left
12 * 0 IR 013\r Enter
13 * 0 IR 014\r Re-Sync
14 * 0 IR 015\r Source Analog RGB for D-sub
15 * 0 IR 017\r Source YPbPr for D-sub
16 * 0 IR 019\r Source Composite Video
17 * 0 IR 021\r Aspect ratio 16:9
18 * 0 IR 022\r Aspect ratio 4:3
19 * 0 IR 023\r Volume +
20 * 0 IR 024\r Volume –
21 * 0 IR 025\r Brightness
22 * 0 IR 026\r Contrast
23 * 0 IR 027\r Color Temperature
24 * 0 IR 030\r Hide
25 * 0 IR 031\r Source
26 * 0 IR 032\r Video: Color saturation adjustment
27 * 0 IR 033\r Video: Hue adjustment
28 * 0 IR 034\r Video: Sharpness adjustment
29 * 0 IR 035\r Query Model name
30 * 0 IR 036\r Query Native display resolution
31 * 0 IR 037\r Query company name
32 * 0 IR 040\r Aspect ratio L.Box
(For P5330W/P5530/P5630)
33 * 0 IR 042\r Keystone Up
34 * 0 IR 043\r Keystone Down
35 * 0 IR 044\r Keystone Left
36 * 0 IR 045\r Keystone Right

X1126AH/X1226AH/X1326AWH Confidential 
 No Code (character) Function feature
37 * 0 IR 046\r Zoom
38 * 0 IR 049\r Language
39 * 0 IR 050\r Source HDMI
40 * 0 IR 051\r ECO mode on
41 * 0 IR 052\r Query ECO mode
42 * 0 IR 053\r Back
43 * 0 IR 054\r Zoom Out
44 * 0 IR 055\r ECO mode off
45 * 0 IR 056\r 3D On
46 * 0 IR 057\r 3D Off
47 * 0 IR 060\r 3D format - Auto
48 * 0 IR 061\r 3D format - Frame Packing
49 * 0 IR 062\r 3D format - Side by Side Half
50 * 0 IR 064\r 3D format - Top and Bottom
51 * 0 IR 065\r 3D L/R Invert
52 * 0 IR 066\r 3D format - Frame Sequential
53 * 0 IR 068\r Source HDMI 2
54 * 0 IR 072\r Source LAN/WIFI
55 * 0 IR 073\r Query Information

Note: The command with end "\r" means "Enter".

X1126AH/X1226AH/X1326AWH Confidential