How To Import A SACS Model Into GeniE
Uploaded by
João Henrique Volpini MattosHow To Import A SACS Model Into GeniE
Uploaded by
João Henrique Volpini MattosSTRENGTH AT SEA
INTEGRITY MANAGEMENT
RISK AND RELIABILITY
SesamTM 40 years of success
How to import a Sacs model into GeniE
Ole Jan Nekstad
15 March 2012
Importing a Sacs model into GeniE
General about the Sacs GeniE data translation What can be automatically imported What must be manually modified
How to verify that the GeniE model is the same as the Sacs model
How to run linear analysis of the imported model How to look at results of the imported model What purposes can the imported model serve
Use GeniE version 6.2 or later
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 2
Capabilities and Limitations
Listed in separate document
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 3
Automatic import
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 4
How to import a model from Sacs
The procedure today
Import structure (automatic) Import wave load data (automatic) Import load combinations (automatic) Add soil data, blanket and wind loads Verify model with previous reports or model data Run a linear static analysis and verify selected key results (displacements, forces and stresses)
You can do it
Without training or assistance By reading our tutorial Learning from a course where the goal is to import 3 structures We can do it as a consulting service to you
Once the model is verified it can be used for all purposes in Sesam
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 5
Import structure, loads, wave data and load combinations
Remember to specify database units before importing
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 6
Decide how to import
Normally use the following settings if there is wave data. For topsides ignore import wave load data
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 7
Joint and beam numbers - 1
The imported model has the same number as the Sacs model For the purpose of change capacity and making a true GeniE model you should change the mesh settings to always regenerate mesh
When you make a new analysis the finite element numbers will change
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 8
Joint and beam numbers - 2
If you want to keep the same finite element numbers for existing structure
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 9
Analysis, loads and wave loads
Analysis set-up, loads, wave loads and load combinations are part of the Activity If all data has been correctly imported you can run analysis and look at results
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 10
How do you know that all has been imported correctly?
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 11
Check the log file after import
The log file is located in the workspace
- Data not converted is listed in the beginning of log file
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 12
Check the quality of the model
The verify feature can detect problems and help you understand the model
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 13
Compare GeniE model with Sacs model
Graphical visualisation and easy to query object properties - Structure model, point masse and sets - Total mass and centre of gravity - Properties sections, materials & hydrocoefficients - Local co-ordinate systems beams and plates - Loads both manually applied and waves - Load combinations loads and scaling factors - Soil layers - Displacements, stresses, forces, deflections for single load-case(s) or envelope
From reports - All above - Maximum wave shear and overturning moment - Load sums and reaction forces
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 14
Which purposes can an imported Sacs model serve once it is inside
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 15
Our tools your solutions your decisions
Transportation, launching Deflections, Stresses, Code-check, Fatigue
Transportation, lifting Deflections, Stresses, Code-check, Fatigue
Non-linear analysis, collapse, accidents, re-qualifications
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 16
Linear analysis (wave, pile/soil) Deflections, Stresses, Code-check, Fatigue, Earthquake
Benefits by using Sesam for jackets
New builds covering Manage existing entire life cycle re-analysis models Collapse analysis Requalification Modification work - all phases
MTO, deflection check, code check, fatigue
Understand models over time, Extreme conditions, produce and view results accidents, fire, explosion
Design of new parts Re-design of existing
Same model for all stages can be shared with others for collaboration
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved.
17
Safeguarding life, property and the environment
www.dnv.com
SesamTM 15 March 2012 Det Norske Veritas AS. All rights reserved. 18
