XM-554ZR

SERVICE MANUAL
Ver. 1.1 2006. 03

US Model Canadian Model E Model

SPECIFICATIONS
OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Input level adjustment range 0.3 6 V (RCA pin jacks), 2.8 12 V (High level input) Outputs Speaker terminals Speaker impedance 2 8 (stereo) 4 8 (when used as a bridging amplifier) Maximum output 4 speakers: 110 W 4 (at 4 ) 3 speakers: 150 W 2 (at 2 ) + 300 W 1 (BTL, at 4 ) Rated output (supply voltage at 14.4 V) 4 speakers: 55 W 4 (20 Hz 20 kHz, 0.04% THD, at 4 ) 65 W 4 (20 Hz 20 kHz, 0.1% THD, at 2 ) Frequency response 5 Hz 50 kHz ( +0 dB) 3 Harmonic distortion 0.005% or less (at 1 kHz, 4 ) Low-pass filter 80 Hz, 18 dB/oct High-pass filter 80 Hz, 12 dB/oct Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 16 V Current drain at rated output : 30 A (4 , 55 W 4) Remote input : 1 mA Dimensions Approx. 401 55 264 mm (w/h/d) not incl. projecting parts and controls Mass Approx. 3.2 kg not incl. accessories Supplied accessories Mounting screws (4) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice. Circuit system

STEREO POWER AMPLIFIER

9-887-093-02
2006C04-1 2006. 03

Sony Corporation
eVehicle Division Published by Sony Techno Create Corporation

XM-554ZR
Ver. 1.1

PROTECTOR OPERATION CHECK

Thermal Protect 1. Short across TH901 with the power on. 2. Verify that the protector is operated and LED901 illuminates red. 3. Verify that the protector is released and LED901 illuminates green when the short is removed. 4. Likewise, perform items 1 to 3 for TH902 and TH903. Over Current Protect 1. Short between the positive and negative sides of the speaker output terminals CN903 and CN904 with the power on. (Perform this shorting for each channel on FRONT and REAR.) 2. Verify that the protector is operated and LED901 illuminates red. 3. Verify that the protector is not released and LED901 remains red even when the short is removed. 4. Verify that the protector is released and LED901 illuminates green when the power is turned off and then on again. Offset Protect 1. Short between the +12V terminal of CN905 and the (L+R) + or (L+R) of the speaker output terminal CN904. (Short between +12V terminal and (L+R) + and between +12V terminal and (L+R) .) 2. Verify that the protector is operated and LED901 illuminates red. 3. Verify that the protector is not released and LED901 remains red even when the short is removed. 4. Verify that the protector is released and LED901 illuminates green when the power is turned off and then on again.

TABLE OF CONTENTS 1. GENERAL

Location and Function of Controls .......................................... 3 Connections ............................................................................. 4

2. DISASSEMBLY
2-1. Bottom Plate ........................................................................ 7 2-2. AMP Board Section ............................................................ 8 2-3. Panel (Front) ........................................................................ 8

3. DIAGRAMS
3-1. 3-2. 3-3. 3-4. Block Diagram .................................................................... 9 Printed Wiring Board ........................................................ 11 Schematic Diagram AMP Section (1/2) ........................ 12 Schematic Diagram AMP Section (2/2) ........................ 13

4. EXPLODED VIEWS
4-1. Heat Sink (Main) Section .................................................. 15 4-2. AMP Board Section .......................................................... 16

5. ELECTRICAL PARTS LIST ........................................ 17

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

Notes on Chip Component Replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.

XM-554ZR SECTION 1 GENERAL

Location and Function of Controls
1 POWER/PROTECTOR indicator Lights up in green during operation. When the PROTECTOR is activated the indicator will change from green to red. When the PROTECTOR is activated refer to the Troubleshooting Guide. 2 LEVEL adjustment control The input level can be adjusted with this control. Turn it in the clockwise direction when the output level of the car audio unit seems low. 3 HPF switch When the HPF switch is set to ON, the Highpass filter (80 Hz) is effective. 4 LPF switch When the LPF switch is set to ON, the Lowpass filter (80 Hz) is effective.

This section is extracted from instruction manual.

Precautions
This unit is designed for negative ground 12 V DC operation only. Use speakers with an impedance of 2 to 8 (4 to 8 when used as a bridging amplifier). Do not connect any active speakers (with builtin amplifiers) to the speaker terminals of the unit. Doing so may damage the active speakers. Avoid installing the unit in areas subject to: high temperatures such as from direct sunlight or hot air from the heater rain or moisture dust or dirt. If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool down before use. When installing the unit horizontally, be sure not to cover the fins with the floor carpet etc. If this unit is placed too close to the car audio unit or aerial, interference may occur. In this case, relocate the amplifier away from the car audio unit or aerial. If no power is being supplied to the car audio unit, check the connections. This power amplifier employs a protection circuit* to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the protection circuits by covering the heat sink or connecting improper loads. Do not use the unit on a weak battery as its optimum performance depends on a good power supply. For safety reasons, keep your car audio unit volume moderate so that you can still hear sounds outside your car.

Fuse Replacement
If the fuse blows, check the power connection and replace both the fuses. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.

Warning
When replacing the fuse, be sure to use one matching the amperage stated above the fuse holder. Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit.

Emplacement et fonction des commandes

1 Indicateur POWER/PROTECTOR Sallume en vert en cours de fonctionnement. Lorsque PROTECTOR est activ, lindicateur passe du vert au rouge. Lorsque PROTECTOR est activ, reportezvous au Guide de dpannage. 2 Commande de rglage LEVEL Le niveau dentre peut se rgler avec cette commande. Tournez cette commande dans le sens des aiguilles dune montre lorsque le niveau de sortie de lautoradio semble faible. 3 Commutateur HPF Lorsque le commutateur HPF est rgl sur ON, le filtre passe-haut (80 Hz) est activ. 4 Commutateur LPF Lorsque le commutateur LPF est rgl sur ON, le filtre passe-bas (80 Hz) est activ.

Ubicacin y funcin de los controles

1 Indicador POWER/PROTECTOR Se ilumina en verde durante el uso. Si se activa PROTECTOR, el indicador cambiar de verde a rojo. Si se activa PROTECTOR, consulte la Gua de solucin de problemas. 2 Control de ajuste LEVEL Mediante este control se puede ajustar el nivel de entrada. Grelo en el sentido de las agujas del reloj si el nivel de salida del sistema de audio para automvil parece bajo. 3 Interruptor HPF Cuando el interruptor HPF est ajustado en ON, se activa el filtro de paso alto (80 Hz). 4 Interruptor LPF Cuando el interruptor LPF est ajustado en ON, se activa el filtro de paso bajo (80 Hz).

* Protection circuit This amplifier is provided with a protection circuit that operates in the following cases: when the unit is overheated when a DC current is generated when the speaker terminals are short-circuited. The colour of the POWER/PROTECTOR indicator will change from green to red, and the unit will shut down. If this happens, turn off the connected equipment, take out the cassette tape or disc, and determine the cause of the malfunction. If the amplifier has overheated, wait until the unit cools down before use.

If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer.

HPF (80Hz)
POWER/ PROTECTOR
OFF
2 4 6 0.3V 1 ON 0.5

LPF(80Hz)
OFF
2 4 6 0.3V 1 ON 0.5

LEVEL

LEVEL

FRONT

REAR

Prcautions
Cet appareil est conu pour fonctionner uniquement sur un courant de 12 V CC avec masse ngative. Utilisez des haut-parleurs dune impdance approprie de 2 8 (stro), 4 8 (en cas dutilisation comme amplificateur en pont). Ne raccordez pas de haut-parleurs actifs (avec amplificateurs intgrs) aux bornes des hautparleurs de cet appareil. Cela risquerait en effet dendommager les haut-parleurs actifs. Ninstallez pas lappareil dans des endroits soumis : des tempratures leves, comme en plein soleil ou prs du chauffage ; la pluie ou lhumidit ; la poussire ou la salet. Si votre voiture est gare en plein soleil et que la temprature a considrablement augment lintrieur de lhabitacle, laissez lappareil refroidir avant de lutiliser. Si vous installez lappareil lhorizontale, ne recouvrez pas les ailettes de ventilation avec le tapis de sol ou quoi que ce soit dautre. Si cet appareil est plac trop prs de lautoradio ou de lantenne, il se peut que des interfrences se produisent. Dans ce cas, loignez lamplificateur de lautoradio ou de lantenne. Si lautoradio nest pas aliment, vrifiez les connexions. Cet amplificateur de puissance est quip dun circuit de protection * conu pour protger les transistors et les haut-parleurs en cas de dfaillance de lamplificateur. Nessayez pas de tester lefficacit des circuits de protection en recouvrant le dissipateur thermique ou en effectuant de mauvaises connexions. Nutilisez pas lappareil avec une batterie faible, car sa performance optimale dpend dune bonne alimentation en lectricit. Pour des raisons de scurit, maintenez le volume de lautoradio un niveau modr afin dentendre les bruits extrieurs.

Precauciones
Remplacement du fusible
Si le fusible fond, vrifiez les connexions de lalimentation et remplacez le fusible. Si le fusible fond de nouveau aprs avoir t remplac, cela peut rvler une dfaillance interne de lappareil. Dans ce cas, consultez votre distributeur Sony le plus proche.
Esta unidad est diseada para utilizarse slo con cc de 12 V negativo a masa. Emplee altavoces con impedancia de 2 a 8 (de 4 a 8 cuand se utilice como amplificador en puente). No conecte altavoces activos (con amplificadores incorporados) a los terminales de altavoz de la unidad, ya que puede daar dichos altavoces. Evite instalar la unidad en lugares expuestos a: altas temperaturas, como a la luz solar directa o al aire caliente de la calefaccin la lluvia o la humedad suciedad o polvo. Si aparca el automvil bajo la luz solar directa y se produce un considerable aumento de temperatura en el interior, deje que la unidad se enfre antes de utilizarla. Si instala la unidad horizontalmente, asegrese de no cubrir las aletas con la moqueta del suelo, etc. Si coloca la unidad demasiado cerca del sistema de audio para automvil o de la antena, pueden producirse interferencias. En este caso, instale el amplificador alejado de dichos dispositivos. Si el sistema de audio para automvil no recibe alimentacin, compruebe las conexiones. Este amplificador de potencia emplea un circuito de proteccin * para proteger los transistores y los altavoces en caso de que dicho amplificador presente fallos de funcionamiento. No intente someter a prueba los circuitos de proteccin cubriendo el disipador de calor o conectando cargas inadecuadas. No utilice la unidad si la batera se est agotando, ya que el rendimiento ptimo de dicha unidad depende de un buen suministro de alimentacin. Por razones de seguridad, mantenga el volumen del sistema de audio para automvil en un nivel moderado de forma que sea posible or los sonidos del exterior del automvil.

Sustitucin del fusible

Si el fusible se funde, compruebe la conexin de alimentacin y sustituya ambos fusibles. Si el fusible se funde de nuevo despus de sustituirlo, es posible que exista un fallo de funcionamiento interno. En este caso, pngase en contacto con el distribuidor Sony ms prximo.

Avertissement
Lorsque vous remplacez le fusible, veillez utiliser un fusible dont la capacit en ampres correspond celle inscrite sur le porte-fusible. Nutilisez jamais de fusible dont la capacit dpasse celle du fusible fourni avec lappareil car cela pourrait endommager lappareil.

Advertencia
Al sustituir el fusible, asegrese de utilizar uno cuyo amperaje coincida con el especificado en el portafusible. No utilice nunca un fusible con un amperaje superior al del suministrado con la unidad, ya que podra daar la unidad.

* Circuit de protection Cet amplificateur est fourni avec un circuit de protection qui entre en fonction dans les cas suivants : lorsque lappareil est en surchauffe ; lorsquun courant continu est gnr ; lorsque les bornes de haut-parleur sont courtcircuites. La couleur de lindicateur POWER/PROTECTOR passe du vert au rouge et lappareil se met hors tension. Dans ce cas, teignez les appareils raccords, retirez la cassette ou le disque et dterminez lorigine du problme. Si lamplificateur est en surchauffe, attendez quil refroidisse avant dutiliser lappareil.

* Circuito de proteccin Este amplificador dispone de un circuito de proteccin que se activa en los siguientes casos: Si la unidad se calienta excesivamente Si se genera corriente cc Si los terminales de altavoz se cortocircuitan. El color del indicador POWER/PROTECTOR cambiar de verde a rojo y la unidad se desactivar. Si esto ocurre, desactive el equipo conectado, extraiga la cinta de casete o el disco y determine la causa del fallo de funcionamiento. Si el amplificador se ha sobrecalentado, espere hasta que la unidad se enfre antes de volver a utilizarla.

Si vous avez des questions ou des problmes concernant votre appareil qui ne sont pas abords dans ce mode demploi, adressez-vous votre distributeur Sony le plus proche.

Si desea realizar alguna consulta o solucionar algn problema relativos a la unidad que no aparezcan en este manual, pngase en contacto con el distribuidor Sony ms prximo.

XM-554ZR

Connections
Installation
Before Installation
Mount the unit either inside the trunk or under a seat. Choose the mounting location carefully so the unit will not interfere with the normal movements of the driver and it will not be exposed to direct sunlight or hot air from the heater. Do not install the unit under the floor carpet, where the heat dissipation from the unit will be considerably impaired. First, place the unit where you plan to install it, and mark the positions of the 4 screw holes on the mounting board (not supplied). Then drill a 3 mm ( 1/ 8 in) pilot hole at each mark and mount the unit onto the board with the supplied mounting screws. The mounting screws are all 15 mm ( 19/ 32 in) long, so make sure that the mounting board is thicker than 15 mm ( 19/ 32 in).

Cautions
Before making any connections, disconnect the ground terminal of the car battery to avoid short circuits. Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be damaged. This is a Phase-Inverted Amplifier. Do not connect the # terminal of the speaker system to the car chassis, and do not connect the # terminal of the right speaker with that of the left speaker. Install the input and output cords away from the power supply wire as running them close together can generate some interference noise. This unit is a high powered amplifier. Therefore, it may not perform to its full potential if used with the speaker cords supplied with the car. If your car is equipped with a computer system for navigation or some other purpose, do not remove the ground wire from the car battery. If you disconnect the wire, the computer memory may be erased. To avoid short circuits when making connections, disconnect the +12 V power supply wire until all the other wires have been connected.

Installation
Avant linstallation
Installez lappareil dans le coffre ou sous un sige. Choisissez soigneusement lemplacement de montage afin dviter que lappareil ne gne le conducteur dans ses mouvements et quil ne soit pas expos au rayonnement direct du soleil ou lair chaud du radiateur. Ninstallez pas lappareil sous le tapis de sol car la dissipation thermique ne pourrait pas se faire correctement. Posez dabord lappareil lendroit o vous souhaitez linstaller et tracez un repre de positionnement pour les 4 orifices de vis sur la plaque de montage (non fournie). Percez des orifices de 3 mm ( 1/ 8 po) au niveau de chaque repre et fixez lappareil sur la plaque avec les vis de montage fournies. La longueur des vis de montage est de 15 mm ( 19/ 32 po). Assurez-vous donc que lpaisseur de la plaque de montage est suprieure 15 mm ( 19/ 32 po).

Avertissement
Avant deffectuer les raccordements, dbranchez la borne de masse de la batterie de voiture pour viter de provoquer un courtcircuit. Utilisez des haut-parleurs dune capacit adquate. Si vous utilisez des haut-parleurs de faible capacit, ils risquent dtre endommags. Les phases de cet amplificateur sont inverses. Ne raccordez pas la borne # du systme de haut-parleurs la carrosserie de la voiture, ou la borne # du haut-parleur droit celle du haut-parleur gauche. Eloignez les cordons dentre et de sortie du fil dalimentation lectrique afin dviter que des interfrences ne se produisent. Cet appareil est un amplificateur de haute puissance. Il se peut donc quil natteigne pas sa puissance maximale sil est utilis avec les cordons de haut-parleurs de la voiture. Si votre voiture est quipe dun ordinateur de bord pour la navigation ou autre, ne dbranchez pas le fil de masse de la batterie de la voiture. Si vous dbranchez ce fil, toute la mmoire de lordinateur risque dtre efface. Pour viter tout risque de court-circuit lorsque vous effectuez les raccordements, branchez le fil dalimentation de +12 V uniquement aprs avoir branch tous les autres fils.

Instalacin
Antes de realizar la instalacin
Monte la unidad en el interior del maletero o debajo de un asiento. Elija cuidadosamente el lugar de instalacin de forma que la unidad no dificulte las maniobras normales del conductor y no quede expuesta a la luz solar directa ni al aire caliente de la calefaccin. No instale la unidad debajo de la moqueta del suelo, en cuyo caso la disipacin de calor de la misma disminuir considerablemente. En primer lugar, coloque la unidad donde tenga previsto instalarla y marque sobre la superficie del tablero de montaje (no suministrado) las posiciones de los 4 orificios para los tornillos. A continuacin, perfore los orificios con un dimetro de aproximadamente 3 mm y monte la unidad sobre el tablero con los tornillos de montaje suministrados. Ya que la longitud de estos tornillos es de 15 mm, compruebe que el grosor del tablero de montaje sea superior a 15 mm.

Precaucin
Antes de realizar las conexiones, desconecte el terminal de toma a tierra de la batera del automvil para evitar cortocircuitos. Asegrese de utilizar altavoces con una potencia nominal adecuada. Si emplea altavoces de capacidad reducida, pueden daarse. Este amplificador es de fase invertida. No conecte el terminal # del sistema de altavoces al chasis del automvil, ni el terminal # del altavoz derecho al del altavoz izquierdo. Instale los cables de entrada y salida alejados del cable de la fuente de alimentacin, ya que en caso contrario puede generarse ruido por interferencias. Esta unidad es un amplificador de alta potencia. Por tanto, puede no funcionar a pleno rendimiento si se utiliza con los cables de altavoz suministrados con el automvil. Si el automvil est equipado con un sistema de ordenador para la navegacin o para otra finalidad, no desconecte el conductor de toma a tierra de la batera del automvil. Si lo desconecta, la memoria del ordenador puede borrarse. Para evitar cortocircuitos al realizar las conexiones, desconecte el cable de la fuente de alimentacin de +12 V hasta conectar todos los cables.

Mount the unit as illustrated. Montez lappareil comme illustr. Monte la unidad tal como se muestra en la ilustracin.

Make the terminal connections as illustrated below. Effectuez les connexions des bornes comme illustr ci-dessous. Realice las conexiones de terminal como se ilustra a continuacin.

Power Connection Wires (not supplied) Cbles dalimentation (non fournis) Cables de conexin de alimentacin (no suministrados)
to a metal point of the car vers un point mtallique de la carrosserie a un punto metlico del automvil

REM

+12V

GND

3
REM

+12V

GND

c
Remote output *1 Sortie de tlcommande *1 Salida remota *1 (REM)
less than 450 mm (18 in) moins de 450 mm (18 po) menos de 450 mm

Pass the wires through the cap, connect the wires, then cover the terminals with the cap.
Note When you tighten the screw, be careful not to apply too much torque * as doing so may damage the screw. * The torque value should be less than 1 Nm.

Car audio unit Autoradio Sistema de audio para automvil

*2
Fuse (50 A) Fusible (50 A) Fusible (50 A) +12 V car battery Batterie de voiture +12 V Batera de automvil de +12 V

Faites passer les fils par le cache, raccordez les fils, puis recouvrez les bornes avec le cache.
Remarque Lorsque vous vissez la vis, faites attention ne pas appliquer une trop grande force *, car cela pourrait endommager la vis. * Le couple de serrage doit tre infrieur 1 Nm.

Pase los cables a travs de la cubierta, conctelos y cubra los terminales con dicha cubierta.
Nota Al apretar el tornillo, tenga cuidado de no aplicar demasiada fuerza de torsin *, ya que puede daarlo. * El valor de fuerza de torsin debe ser inferior a 1 Nm.

*1 If you have the factory original or some other car audio unit without a remote output for the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. In High level input connection, car audio unit can also be activated without need for REMOTE connection. However, this function is not guaranteed for all car audio units. *1 Si vous disposez de lautoradio dorigine ou dun autre autoradio dont lamplificateur ne comporte pas de sortie de tlcommande distance, raccordez la borne dentre de commande distance (REMOTE) la prise dalimentation accessoires. Dans une connexion dentre haut niveau, lautoradio peut galement tre activ sans raccordement REMOTE. Toutefois, cette fonction nest pas garantie pour tous les autoradios. *1 Si dispone del sistema de audio para automvil original de fbrica o de otro sistema sin una salida remota para el amplificador, conecte el terminal de entrada remota (REMOTE) a la fuente de alimentacin auxiliar. En la conexin de entrada de alto nivel, el sistema de audio para automvil tambin puede activarse sin necesidad de conexin REMOTE. No obstante, esta funcin no se garantiza en todos los sistemas de audio para automvil.

XM-554ZR

Notes on the power supply

Connect the +12 V power supply wire only after all the other wires have been connected. Be sure to connect the ground wire of the unit securely to a metal point of the car. A loose connection may cause a malfunction of the amplifier. Be sure to connect the remote control wire of the car audio unit to the remote terminal. When using a car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. Use a power supply wire with a fuse attached (50 A). All power wires connected to the positive battery post should be fused within 450 mm (18 in) of the battery post, and before they pass through any metal. Make sure that the vehicles battery wires connected to the vehicle (ground to chassis) *2 are of a wire gauge at least equal to that of the main power wire connected from the battery to the amplifier. During full-power operation, a current of more than 50 A will run through the system. Therefore, make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 10-Gauge (AWG-10) or have a sectional area of more than 5 mm 2 ( 7/32 in 2). Tous les fils lectriques raccords la borne positive de la batterie doivent tre protgs par un fusible une distance maximum de 450mm (18 po) la borne de la batterie et avant de passer dans une partie mtallique quelconque. Assurez-vous que les fils de la batterie du vhicule raccords ce dernier (sol au chssis) *2 sont dun calibre au moins gal celui du fil lectrique principal reliant la batterie et lamplificateur. Pendant une utilisation pleine puissance, un courant dune intensit suprieure 50 A circule dans le systme. Assurez-vous que les cbles raccorder aux bornes +12 V et GND de cet appareil sont de calibre suprieur 10 (AWG-10) ou dune section suprieure 5 mm 2 ( 7/32 po 2).

Input Connections/Connexions dentre/Conexiones de entrada

Line Input Connection Connexion dentre de ligne Conexin de entrada de lnea

Car audio unit Autoradio Sistema de audio para automvil

Remarques sur lalimentation lectrique

Raccordez le cble dalimentation +12 V uniquement aprs avoir ralis toutes les autres connexions. Raccordez solidement le fil de masse de lappareil un point mtallique de la carrosserie. Une connexion lche risque de provoquer un problme de fonctionnement de lamplificateur. Veillez raccorder le fil de commande distance de lautoradio la borne de commande distance. Si vous utilisez un autoradio dont lamplificateur ne comporte pas de sortie de commande distance, raccordez la borne dentre de commande distance (REMOTE) la prise dalimentation accessoires. Utilisez un cble dalimentation dot dun fusible (50 A).

LINE OUT
Front Avant Delanteros

LINE OUT
Rear Arrire Traseros

Notas sobre la fuente de alimentacin

Conecte el cable de la fuente de alimentacin de +12 V slo despus de haber conectado los otros cables. Asegrese de conectar firmemente el cable de toma a tierra de la unidad a un punto metlico del automvil. Una conexin floja puede causar fallos de funcionamiento del amplificador. Compruebe que conecta el cable de control remoto del sistema de audio para automvil al terminal remoto. Si utiliza un sistema de audio para automvil sin salida remota en el amplificador, conecte el terminal de entrada remota (REMOTE) a la fuente de alimentacin auxiliar. Emplee el cable de la fuente de alimentacin con un fusible fijado (50 A). Todos los cables de alimentacin conectados al polo positivo de la batera deben conectarse a un fusible situado a menos de 450 mm del polo de la batera, y antes de pasar por ninguna pieza metlica. Asegrese de que los cables de la batera del vehculo conectados al mismo (a la masa del chasis) *2 tienen una anchura igual o superior a la del cable de alimentacin principal que conecta la batera con el amplificador. Durante el funcionamiento a pleno rendimiento, fluye por el sistema una corriente superior a 50 A. Por tanto, compruebe que los cables que va a conectar a los terminales de +12 V y GND de esta unidad son del calibre 10 (AWG 10) como mnimo o presentan un rea de seccin superior a 5 mm 2.

High Level Input Connection (with Speaker Connection 3) Connexion dentre haut niveau (avec connexion de haut-parleur 3) Conexin de entrada de alto nivel (con conexin de altavoces 3)

Front right speaker output Sortie du haut-parleur avant droit Salida del altavoz delantero derecho Grey Gris Gris Striped Ray Con rayas White Blanc Blanco Striped Ray Con rayas Front left speaker output Sortie du haut-parleur avant gauche Salida del altavoz delantero izquierdo

Rear right speaker output Sortie du haut-parleur arrire droit Salida del altavoz trasero derecho Purple Mauve Violeta

Car audio unit Autoradio Sistema de audio para automvil

Striped Ray Con rayas Green vert Verde Striped Ray Con rayas

Rear left speaker output Sortie du haut-parleur arrire gauche Salida del altavoz trasero izquierdo

High Level Input Connector Connecteur dentre haut niveau Conector de entrada de alto nivel

Grey Gris Gris White Blanc Blanco Striped/White Ray blanc Con rayas/Blanco Striped/Grey Ray gris Con rayas/Gris

Green Vert Verde

FRONT

REAR

Purple Mauve Violeta Striped/Purple Ray mauve Con rayas/Violeta Striped/Green Ray vert Con rayas/Verde

L R

L R

XM-554ZR

Speaker Connections
Turn on or off the LPF and HPF switch at the unit rear as illustrated below.

Conexins des haut-parleurs

Rglez le commutateur LPF et HPF situ larrire de lappareil On ou Off, comme indiqu dans lillustration ci-dessous.

Conexiones de los altavoces

Encienda o apague el interruptor LPF y HPF situados en la parte posterior de la unidad, como se muestra a continuacin.

4-Speaker System Systme 4 haut-parleurs Sistema de 4 altavoces

3-Speaker System Systme 3 haut-parleurs Sistema de 3 altavoces

Left gauche Izquierdo

Front speaker (min. 2 ) Haut-parleurs avant (min. 2 ) Altavoces delanteros (mn. 2 )

Right droit Derecho

Left gauche Izquierdo

Full range speakers (min. 2 ) Hauts-parleurs pleine gamme (min. 2 ) Altavoces de gama completa (mn. 2 )

Right droit Derecho

HPF (80Hz)
OFF ON

LPF(80Hz)
OFF ON

HPF (80Hz)
OFF ON

LPF(80Hz)
OFF ON

Left gauche Izquierdo

Right droit Derecho

Rear speaker (min. 2 ) Haut-parleurs arrire (min. 2 ) Altavoces traseros (mn. 2 )

Subwoofer (min. 4 ) Caisson de graves (min. 4 ) Altavoz potenciador de graves (mn. 4 )

Notes In this system, the volume of the subwoofer will be controlled by the car audio unit fader control. In this system, the output signals to the subwoofer will be the combination of both the REAR L and R INPUT jacks or the REAR high level input connector signals. Remarques Dans ce systme, le volume du caisson de graves est contrl par la commande de balance avant/ arrire de lautoradio. Dans ce systme, les signaux mis vers le caisson de graves sont constitus des signaux des prises REAR L et R INPUT ou des signaux du connecteur dentre de haut niveau REAR.

Notas En este sistema, el volumen del altavoz potenciador de graves se controla mediante el control de equilibrio entre altavoces del sistema de audio para automvil. En este sistema, las seales de salida que recibe el altavoz potenciador de graves sern la combinacin de las tomas REAR L y R INPUT o de las seales del conector de entrada de alto nivel REAR.

2-Way System Systme 2 voies Sistema de 2 vas

Left gauche Izquierdo

Full range speakers (min. 2 ) Hauts-parleurs pleine gamme (min. 2 ) Altavoces de gama completa (mn. 2 )

Right droit Derecho

HPF (80Hz)
OFF ON

LPF(80Hz)
OFF ON

Note In this system, the volume of the subwoofer will be controlled by the car audio unit fader control.
Left gauche Izquierdo Right droit Derecho

Remarque Dans ce systme, le volume du caisson de graves est contrl par la commande de balance avant/arrire de lautoradio. Nota En este sistema, el volumen del altavoz potenciador de graves se controla mediante el control de equilibrio entre altavoces del sistema de audio para automvil.

Subwoofer (min. 2 ) Caisson de graves (min. 2 ) Altavoz potenciador de graves (mn. 2 )

XM-554ZR SECTION 2 DISASSEMBLY

Note : This set can be disassemble according to the following sequence.

SET 2-1. BOTTOM PLATE (Page 7) AMP BOARD SECTION (Page 8) PANEL (FRONT) (Page 8)

2-2.

2-3.

Note : Follow the disassembly procedure in the numerical order given.

2-1. BOTTOM PLATE

2 four screws (+BTP 3 6) 1 three screws (+BTP 3 6)

3 bottom plate

XM-554ZR

2-2. AMP BOARD SECTION

3 three screws (+P 3 8)

4 screw (+BTP 3 8) 2 three screws (+P 3 8)

1 three screws (+P 3 8)

5 AMP board section

heat sink (main)

2-3. PANEL (FRONT)

5 AMP board

4 panel (front)

3 screw (+P 3 8)

2 screw (+P 3 8)

1 three screws (+P 3 8)

XM-554ZR SECTION 3 DIAGRAMS

3-1. BLOCK DIAGRAM
(FRONT)
PRE AMP IC801 (1/2) CN902 (1/2) L -1 3 2 HPF IC803 (1/2) 2 3 1 VR801-1 2 HPF FRONT VR801 LEVEL (FRONT) GAIN CONTROL AMP IC805 (2/2) VR801-2 6 HPF 6 5 7 7 MUTE CONTROL Q809 SW801-2 DIFFERENTIAL AMP Q202 DRIVE AMP Q205 SW801-1 MUTE CONTROL Q810 DIFFERENTIAL AMP Q102 MUTE SWITCH Q201 DRIVE AMP Q105 1 GAIN CONTROL AMP IC805 (1/2) 1 MUTE SWITCH Q101 OVERLOAD DET Q112 DIFFERENTIAL AMP Q103 DRIVE AMP Q104 BIAS Q106,107 DRIVE AMP Q109 POWER AMP Q111 OVERLOAD DET Q212 DRIVE AMP Q208 BIAS Q206,207 DRIVE AMP Q209 POWER AMP Q211 POWER AMP Q210 R DRIVE AMP Q108 POWER AMP Q110 CN903 FRONT SPEAKER OUT

PRE AMP IC801 (2/2) -2 R D906 INPUT CN901 HIGH LEVEL INPUT/ SENSING POWER ON FR D907 RL RR PRE AMP IC802 (1/2) CN902 (2/2) L (L+R) -3 3 2 LPF 2 3 LPF IC804 (1/2) FL 6 5 7 HPF IC803 (2/2)

SW801 HPF (80Hz) (FRONT)

ON OFF

DIFFERENTIAL AMP Q203

DRIVE AMP Q204

(REAR)
GAIN CONTROL AMP IC806 (1/2) VR802-1 1 2 1 MUTE CONTROL Q811 VR802 LEVEL (REAR) LPF IC804 (2/2) VR802-2 3 6 5 7 6 7 MUTE CONTROL Q812 DIFFERENTIAL AMP Q402 DRIVE AMP Q405 GAIN CONTROL AMP IC806 (2/2) MUTE SWITCH Q301 OVERLOAD DET Q312 DIFFERENTIAL AMP Q303 DRIVE AMP Q304 BIAS Q306,307 DIFFERENTIAL AMP Q302 MUTE SWITCH Q401 DRIVE AMP Q305 DRIVE AMP Q309 POWER AMP Q311 OVERLOAD DET Q412 DIFFERENTIAL AMP Q403 DRIVE AMP Q404 BIAS Q406,407 DRIVE AMP Q409 POWER AMP Q411 DRIVE AMP Q408 POWER AMP Q410 R DRIVE AMP Q308 POWER AMP Q310 CN904 REAR SPEAKER OUT

REAR

SW802-1 SW802 LPF (80Hz) (REAR) OFF ON 7 LPF

PRE AMP IC802 (2/2) R (L+R) -4 6 5

(L+R)

SW802-2

MUTE CONTROL Q802 PROTECTOR DETECT Q901,902 F901 25A DC-DC CONVERTER IC903 B+ SWITCH Q905 OVER VOLTAGE DETECT Q907 D905 THERMAL DET Q914,915 D902 REM POWER ON/OFF Q906 G (POWER) LED DRIVER Q903 R (PROTECTOR) LED901 POWER/ PROTECTOR 15 16 1 2 D901 11 10 SWITCHING DRIVER Q912,913 15V REG Q808 12 VCC 8 9 SWITCHING DRIVER Q910,911 OVERLOAD PROTECT (REAR) Q805,806 DC-DC CONVERTER TRANSFORMER T901

OVERLOAD PROTECT (FRONT) Q803,804

CN905 +12V

F902 25A

DC DET IC902

D803 RECT +30V

REF. REG TEMP.DET TH901-903 BUFFER Q904 14 REF

GND

DRIVER Q908,909 D804 RECT

+15V REG Q807

+15V

Signal path : AUDIO

30V

15V

XM-554ZR

XM-554ZR
Ver. 1.1

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: All capacitors are in F unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

A : B+ Line. B : B Line. Power voltage is dc 14.4V and fed with regulated dc power supply from +12V and REM terminals. Voltage is dc with respect to ground under no-signal condition. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : AUDIO for printed wiring boards: : Pattern from the side which enables seeing.

Waveform

IC903 5

3.3 Vp-p

18 sec 1 V/DIV, 10 sec/DIV

XM-554ZR

10

10

XM-554ZR

3-2. PRINTED WIRING BOARD

: Uses unleaded solder.

1 A

10

11

12

13

AMP BOARD
Q311 Q310 Q411 Q410 C823 E C B E C B E C B E C B JW158

TH901

JW175

R270

R277

R278

ECB

R907

R908

R464

R364

R363

R470

R378

ECB

R365

ECB

R465

ECB

R478

ECB

R267

JW121

JW155 JW154

R367

R467

R477

K A

Q307

Q312 R469

Q210

L803

C822

JW139

L801

C818

R368

R468

C820

L802

R369

Q407

Q412

JW129

JW65

Q207 B

JW72

JW76

JW80

A JW84 JW112
JW88 JW113 JW89 JW90 JW91 JW115 JW116

K T901 S JW150 R931 D G

Q206

R268

C E

BCE
JW101 JW102 JW103 JW104

D804

R263

JW110

JW114

D803

R377 R370

R463

Q306 E C B

Q406 E C B

L805

L804

Q212

JW165

JW166

TH902

C817

JW164 D901

C821

C819

R265

JW73
JW64

JW77

JW81 JW85
JW117 JW118 JW119

Semiconductor Location
Ref. No. D101 D102 D201 D202 D301 D302 D401 D402 D801 D802 D803 D804 D805 D806 D807 D901 D902 D904 D905 D906 D907 IC801 IC802 IC803 IC804 IC805 IC806 IC902 IC903 LED901 Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Location F-4 F-4 F-5 F-4 F-6 F-5 F-7 F-6 G-9 G-9 B-13 C-13 F-7 F-8 D-10 B-4 G-10 H-10 G-10 I-6 I-6 H-5 H-6 G-4 G-7 G-4 H-7 F-9 E-10 I-8 G-4 F-4 F-4 E-4 E-4 F-2 F-2 E-4 E-4 E-1 F-1 D-2 G-4 F-5 F-5 E-5 E-5 C-2 C-2 E-5 E-5 Ref. No. Q210 Q211 Q212 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q311 Q312 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q410 Q411 Q412 Q802 Q803 Q804 Q805 Q806 Q807 Q808 Q809 Q810 Q811 Q812 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 Q915 Location C-1 D-1 B-2 G-6 F-6 F-6 E-6 E-5 B-6 C-6 E-6 E-5 A-7 A-5 B-7 F-6 F-7 F-7 E-7 E-6 B-8 C-8 E-7 E-6 A-9 A-8 C-10 G-9 H-3 H-3 G-8 G-8 F-8 E-8 G-7 G-7 G-6 G-6 E-10 E-10 I-8 F-10 G-10 G-10 H-10 E-11 E-11 E-13 F-13 E-13 D-13 G-10 G-10
Q913 JW181
1-868-781- 11

R264

R269

E C118

JW75

JW79

JW83
JW142 JW141

JW111

JW159

R177 R170

JW67

Q112 BCE R178

JW144

JW93

JW122

JW68

ECB ECB

R902 R901

JW71

JW70

C154

C254

JW124

R167

JW123

R923

Q110

JW173 JW170

C Q105 Q104 C152 Q205 R260 JW45 D202 D101 Q204 C252

R925

C906

R912 C907 JW172 C904 JW171

JW60

JW61

JW62

JW63

E R163 B Q107

R160

R155 R157

R156 R158

R255 R257 R256 R258

R455 R457

R456 R458

R355 R357

R356 R358

R159

R259

Q305 R360 D302

C352

TH903

R460 R359 JW95 D301 D402

JW98

C452

R815 R459
JW100

16 1

IC903

9 8

R814

Q908

R947

JW37

R926 R927

Q106

JW127

R168

JW128

JW126

R920

JW56

R165

JW125

R169

JW192 JW191

C913

JW58

R353

C353

R453 C453

R154

C253

Q111

R262

R162

R153 C153

R161

R253

R254

R261

JW52

C E C119

JW59

JW38 R152

R361

JW42

R354

JW96

R362

R452 R462

R461

R454

JW169 IC902 JW177 1 2 JR4 C903 JW176 4 3

JW143

JW57

C914

R164

Q102 C2 C1 C2 C1 Q103 R173 B2 E B1B2 E B1R174

C905

Q904

D G R928

C824

C825 C827

BCE

C151 ECB Q101 R151 R252 ECB Q201

R909

C251 R251

R806 R818 R816 R817

BCE

JW131

BCE

R105 JW17 R107 JW47 C107

JW107 JW160

JW130

JW132

BCE

JW106

JW138

JW34

R807

R808

R937 C921

C116 R103 C117

JW31 JW30

R104

C911 JW184 JW183

GND

JW190

JW189

R109

R114 C808 R209 JW35 C809

C815 R304

C109

JW163

C112

Q806 R811 BCE

R303

R307

R305

JW66

R309

C308

C920

JW53

JW55

JW54

R206

C212

C209 R208

JW27

4 1 IC801 JW135 5 8

R941

4 1 IC802 5 8

JW20 JW13 JW12 JW28 JW11

R408

R314 R409 C410

JW33

C208

JW195

JW49

JW51

R406 C406

4 1 IC806 5 8

JW22

R916

R214

JW9

JW10

4 1 IC804 5 8

R414

JW23

C814

4 1 IC805 5 8

4 1 IC803 5 8

R306

JW24

C105

C306

C305 C307
JW16

Q805 B C E R371

R471

BCE

JW21

C309

R312 JW32

C812 R813

Q802

D801

Q914 Q915 R936 D905

R940

C908

C106 R106

JR5 JW157

C311

JW161

R308

C310 R311 R310

JR6

JW133

D802

ECB ECB

R915 R914

JW188

R108 C108 JW18

B C E Q906 B C E Q907

L901

C211

R113 C110

JW26

JW50

R405 R407 C407

R410

C409

C811 R271

ECB ECB

JW48

C217 R204

R810

C813

R171

JW3

R102

R812

C216 R205

R203 R207

JW36

C405 R403 R404

JW6

C408

Q804

C312 C412 R313 R413 JW46

JW196

R111

JW19 C206 C205 C207

C210

C111

JW15

D904

R411

C317 C316 C417

R213

R101

C401

Q803 R172 C155 C255

JW8

JW14 -2 JW2

C802

C101

JW4

JW5

R402

C202

R412

VR802

(PROTECTOR) R905

ECB

R372 Q903 C355 C455

R472

JW180 JW179 JW178

R201

C102

JW25

-1

R804

R272

VR801

R802 R202

JW7

-2 -1

-4 -3

-6 R301 -5 -7

-8 R401

-2 -1 JW107 -1 -2

C910

R943 R944

C301 C201 C302

R942 C918

R917

R918

SW801 OFF ON SW801 HPF(80Hz)

VR801 LEVEL

R801 C801

R803 C803 D906

C805 R805 D907 SW802 OFF ON SW802 LPF(80Hz)

VR802 LEVEL

-1 L

-3 L

-1

-7 -8 FL FR RL RR

LED901 POWER/ PROTECTOR

(L+R)
-2 R

-2

F901 25A L (L+R) REAR SPEAKER OUT CN904 R

C909

-1 -2

R945 R946 C402

(POWER)

R210

R112 R212

JW29

R211

C804

R919

F902 25A REM CN905 +12V

L CN903 FRONT SPEAKER OUT

CN902 INPUT

-4 R

CN901 HIGH LEVEL INPUT/ SENSING POWER ON

REAR

FRONT

XM-554ZR

11

11

JW182

R904

R110

R302

C416

JR1

JW1

C411

JW198

R934

Q810

R809

C810

Q812

Q811

JW108

R939 R938 R935

JW186

JW185

Q301

Q905 C919 B C E

C912

JW187

JW41

R351

JW162

JW167

BCE

Q809

JW109

JR2 C351 R352

R451

Q401

C451 C826

BCE

D902

JW92

JW168

Q911

R176

R175

JW43 R276 R275 Q202 C2 C1 C2 C1 Q203 R273 B2EB1 B2 E B1R274

R375 R376 Q302 C2 C1 C2 C1 Q303 R373 B2EB1 B2 E B1 R374

R476 R475 JW97 C2 C1 C2 C1 Q403 R473 R474 Q402 B2EB1 B2 E B1

R921

D805

BCE

BCE

D102

D201

D401

JW105

Q807 D806

JW134

R910

R911

R932

C915

G R929

JW153

Q910

Q304

Q405

Q404

R924

ECB

Q808

JW174

JW99

Q902

JR3

R166

R266

R466

R922

ECB

BCE

BCE

BCE

Q308 R366

BCE

JW148

R906

C454

BCE

C354

Q109

Q108 BCE

C901 C902

JW120

Q208 Q209 Q309 BCE Q409

Q408 BCE

Q901 JW151 Q909 R930

D G

JW147

JW152

Q912

JW39

JW94

JW140

JW145

JW146

R903 C917 JW149

R933

JW69

JW74

JW78

JW82

JW86 JW87

Q211

D807

C916

XM-554ZR

3-3. SCHEMATIC DIAGRAM AMP SECTION (1/2)

D101

R155

R158

R175

R159 Q104 Q108 R165 R167 R163 R161 C154 Q106 R162 R164 Q107 R169 R166 R168 Q105 Q111 Q109 R160 R171 R178 C155 Q110 R177 R170 Q112 C119 C118

Q103 R174 R112 CN902 R102 IC801(1/2) R108 C111 R173 R103 C105 C107 R104 R105 C110 C106 R106 R107 R109 R111 R110 SW801 IC805(1/2) R114 C108 C109 IC803(1/2) R806 R157 R176 D102 C112 R151 R152 R156 Q102 C151

C152

VR801 R113

Q101

R153

C153

R154

R172

C802

R802

R801

C801 C116

CN903 C117 C206 R206 C207 C205 C208 C209 C212 C211 R273 R205 R204 C217 D906 R943 R944 R201 D907 R301 R401 C317 C316 Q303 R304 C808 C309 R308 R302 R309 R310 R311 R373 C312 C308 R303 C815 R804 C804 C416 R307 C307 C417 C306 R306 SW802 IC806(1/2) R314 C310 IC804(1/2) R817 R357 R376 D302 R360 R351 R352 Q302 R356 R362 R354 Q305 Q309 R371 CN904 C311 R312 VR802 R313 Q301 R374 C351 C352 R945 R946 R355 R358 R375 D301 Q304 R365 R367 IC802(1/2) R353 C353 R363 R361 C354 R364 Q306 Q307 R369 R366 R368 Q311 R378 C355 R359 Q308 Q310 R377 R370 Q312 R212 VR801 R213 R251 R256 Q202 R816 R257 R276 D202 R260 R254 Q205 Q209 R271 Q201 IC803(2/2) R252 R274 C251 R207 R209 C210 R203 R211 R210 R214

IC805(2/2) R255

R258

R275 D201

R259 Q204 Q208 R265 R267 Q210 R277 R270 Q212

Q203

C252

CN902

R202

R208 CN901 IC801(2/2)

R253

C253

R263 R261 C254 Q206 R262 R264 R266 R268 Q211 Q207 R269 R278 C255

R272

C102

C101

C202

C201

C216

R101

C302

C301

C401

C402

R305

CN902

R803

C803

C305

R372

R407 R404 R403 R405 R406 C407 C406 C405 R408 IC802(2/2) R409 R410 C409 R411

R414

IC806(2/2) R455 R458 R475 D401 Q404 Q403 C412 Q401 R452 R474 C451 C452 R465 R467 R453 C453 R463 R461 C454 Q406 R462 R456 Q402 R818 R457 R476 D402 R460 R454 Q405 Q409 R471 R464 Q407 R469 R466 R468 Q411 R478 C455 R459 Q408 Q410 R477 R470 Q412

C408

C410

IC804(2/2)

R402

C411 R412 VR802

R413 R451

R473

C809

R472

(Page 13)

XM-554ZR

12

12

XM-554ZR

Refer to page 10 for Waveform. 3-4. SCHEMATIC DIAGRAM AMP SECTION (2/2) Refer to page 14 for IC Block Diagram.

(Page 12)

R805

C805

Q807 Q812 Q811 Q809 Q810 R926 R923 R922 R807 D802 R808 R920 R929 Q910 Q912 R924 R925 R927 Q909 R930 R931 Q913 Q908 Q911 R928 C915 R932 R933 C916 C914 D804 L803 Q808 C820 C913 C912 L801 L805 C817 C818 L802 C821 C822 T901 L804 D803 C819 R814 C826 D805 D806 R815 C824 C825 C827 C823

R921 Q802 D801 C810 R809

CN905

F902 L901

IC902 Q905

IC B/D

D807

Q803 R810 R915 R935 C919 Q804

F901 C918 R916 R942 D904

TH903

TH902

TH901

Q904

C901 R904 LED901

C811

R812

C813

R914

D905 R940

Q915 D901 R936

R947 C908 C906 IC903 R906 R912 C904 Q902 R901 R902 R905 R811 Q806 Q903 Q805

Q906 R919 R918 C920 R941 C910 C909 R917 Q907 C911 R937 D902 Q914 R939

R908

R909

R907

C921

C903

R911

R938

C907

R903

C902

Q901

C917

C812

R813

C814

R934

R910 C905

XM-554ZR

13

13

XM-554ZR

IC Block Diagram
IC903 PC494GS (AMP BOARD (2/2))
VREF NON OUT VCC

INV

C2

E2
10 Q2 6

16

15

14

13

12 REF 5V

11

ERROR

Q1

ERROR 1 2 3

0.1V 4 5

OSC

7 8

TIME

+IN

-IN

COMPEN

RT

XM-554ZR

GND C1

CT

E1
9

14

14

XM-554ZR SECTION 4 EXPLODED VIEWS

NOTE: The mechanical parts with no reference number in the exploded views are not supplied. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinets Color Accessories are given in the last of this parts list.

Ver. 1.1

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

4-1. HEAT SINK (MAIN) SECTION

not supplied

#1 #1 #1

#1 F901 F902 #2

#1

not supplied

#2 #2

Ref. No. 1 2 0 F901

Part No.

Description

Remark

Ref. No. 0 F902 #1 #2

Part No.

Description

Remark

2-663-766-01 PLATE (TOP), ORNAMENTAL 2-663-767-01 PLATE (SIDE), ORNAMENTAL 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A)

1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A) 7-685-146-19 SCREW +P 3X8 TYPE2 NON-SLIT 7-685-545-19 SCREW +BTP 3X6 TYPE2 N-S

15

XM-554ZR

4-2. AMP BOARD SECTION

not supplied

52 52

51
not supplied

54
Q111,Q110, Q211,Q210 Q311,Q306,Q406,Q410

52

52 54 54
D804,D803 #1

52
not supplied

Q911,Q910,Q912,Q913

52 52

#1

53
#1

Ref. No. 51 52 53 54 D803 D804 Q110 Q111 Q210 Q211

Part No. A-1176-995-A 3-225-183-02 2-663-768-01 3-912-432-11 6-501-466-01 6-501-467-01 6-551-502-01 6-551-503-01 6-551-502-01 6-551-503-01

Description AMP BOARD, COMPLETE SCREW (+PSW.TT.3XL) PANEL (FRONT) SCREW (+B) DIODE F1B2CCI DIODE F1B2CAI TRANSISTOR KTD998 TRANSISTOR KTB778 TRANSISTOR KTD998 TRANSISTOR KTB778

Remark

Ref. No. Q306 Q311 Q406 Q410 Q910 Q911 Q912 Q913 #1

Part No. 8-729-041-66 6-551-503-01 8-729-041-66 6-551-502-01 6-551-506-01 6-551-506-01 6-551-506-01 6-551-506-01 7-685-146-19

Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FET IRFI3205 2SC4015TV2 KTB778 2SC4015TV2 KTD998

Remark

FET IRFI3205 FET IRFI3205 FET IRFI3205 SCREW +P 3X8 TYPE2 NON-SLIT

16

XM-554ZR SECTION 5 ELECTRICAL PARTS LIST

NOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : , for example: uA.. : A.. uPA.. : PA.. uPB.. : PB.. uPC.. : PC.. uPD.. : PD.. CAPACITORS uF : F COILS uH : H When indicating parts by reference number, please include the board. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

Ver. 1.1 AMP

Ref. No.

Part No.

Description

Remark

Ref. No. C305 C306 C307 C308 C309 C310 C311 C312 C316 C317 C351 C352 C353 C354 C355 C401 C402 C405 C406 C407 C408 C409 C410 C411 C412 C416 C417 C451 C452 C453 C454 C455 C801 C802 C803 C804 C805 C808 C809 C810 C811 C812 C813 C814 C815

Part No. 1-162-923-11 1-162-927-11 1-162-927-11 1-126-960-11 1-164-336-11 1-164-345-11 1-126-933-11 1-162-927-11 1-115-339-11 1-115-339-11 1-126-947-11 1-162-919-11 1-162-927-11 1-126-960-11 1-137-397-11 1-162-927-11 1-162-927-11 1-162-923-11 1-162-927-11 1-162-927-11 1-126-960-11 1-164-336-11 1-164-345-11 1-126-933-11 1-162-927-11 1-115-339-11 1-115-339-11 1-126-947-11 1-162-919-11 1-162-927-11 1-126-960-11 1-137-397-11 1-127-715-11 1-126-934-11 1-127-715-11 1-127-715-11 1-115-339-11 1-115-339-11 1-115-339-11 1-126-965-11 1-115-416-11 1-115-416-11 1-104-655-11 1-104-655-11 1-126-933-11

Description CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT MYLAR CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT MYLAR CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 47PF 100PF 100PF 1uF 0.33uF 0.082uF 100uF 100PF 0.1uF 0.1uF 47uF 22PF 100PF 1uF 0.047uF 100PF 100PF 47PF 100PF 100PF 1uF 0.33uF 0.082uF 100uF 100PF 0.1uF 0.1uF 47uF 22PF 100PF 1uF 0.047uF 0.22uF 220uF 0.22uF 0.22uF 0.1uF 0.1uF 0.1uF 22uF 0.001uF 0.001uF 470uF 470uF 100uF 5% 5% 5% 20%

Remark 50V 50V 50V 50V 25V 25V 16V 50V 50V 50V 35V 50V 50V 50V 100V 50V 50V 50V 50V 50V 50V 25V 25V 16V 50V 50V 50V 35V 50V 50V 50V 100V 16V 16V 16V 16V 50V 50V 50V 50V 25V 25V 6.3V 6.3V 16V

A-1176-995-A AMP BOARD, COMPLETE ********************* 3-225-183-02 SCREW (+PSW.TT.3XL) 3-912-432-11 SCREW (+B) < CAPACITOR > C101 C102 C105 C106 C107 C108 C109 C110 C111 C112 C116 C117 C118 C119 C151 C152 C153 C154 C155 C201 C202 C205 C206 C207 C208 C209 C210 C211 C212 C216 C217 C251 C252 C253 C254 C255 C301 C302 1-162-927-11 1-162-927-11 1-162-923-11 1-162-927-11 1-162-927-11 1-115-339-11 1-115-339-11 1-126-933-11 1-126-963-11 1-162-927-11 1-115-339-11 1-115-339-11 1-115-416-11 1-115-416-11 1-126-947-11 1-162-919-11 1-162-927-11 1-126-960-11 1-137-397-11 1-162-927-11 1-162-927-11 1-162-923-11 1-162-927-11 1-162-927-11 1-115-339-11 1-115-339-11 1-126-933-11 1-126-963-11 1-162-927-11 1-115-339-11 1-115-339-11 1-126-947-11 1-162-919-11 1-162-927-11 1-126-960-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT MYLAR CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT 100PF 100PF 47PF 100PF 100PF 0.1uF 0.1uF 100uF 4.7uF 100PF 0.1uF 0.1uF 0.001uF 0.001uF 47uF 22PF 100PF 1uF 0.047uF 100PF 100PF 47PF 100PF 100PF 0.1uF 0.1uF 100uF 4.7uF 100PF 0.1uF 0.1uF 47uF 22PF 100PF 1uF 0.047uF 100PF 100PF 5% 5% 5% 5% 5% 10% 10% 20% 20% 5% 10% 10% 5% 5% 20% 5% 5% 20% 5% 5% 5% 5% 5% 5% 10% 10% 20% 20% 5% 10% 10% 20% 5% 5% 20% 5% 5% 5% 50V 50V 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 25V 25V 35V 50V 50V 50V 100V 50V 50V 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 35V 50V 50V 50V 100V 50V 50V

10% 20% 5% 10% 10% 20% 5% 5% 20% 5% 5% 5% 5% 5% 5% 20% 10% 20% 5% 10% 10% 20% 5% 5% 20% 5% 10% 20% 10% 10% 10% 10% 10% 20% 5% 5% 20% 20% 20%

1-137-397-11 MYLAR 1-162-927-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP

17

XM-554ZR
AMP
Ref. No. C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C901 C902 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 C921 Part No. 1-163-021-11 1-163-021-11 1-165-949-11 1-165-949-11 1-165-949-11 1-165-949-11 1-115-416-11 1-115-339-11 1-115-339-11 1-126-933-11 1-126-933-11 1-100-352-11 1-163-021-11 1-163-021-11 1-163-021-11 1-137-410-11 1-126-933-11 1-115-339-11 1-126-933-11 1-115-416-11 1-117-378-11 1-115-339-11 1-137-397-11 1-131-731-21 1-131-731-21 1-163-021-11 1-163-021-11 1-163-021-11 1-100-352-11 1-100-352-11 Description CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP MYLAR ELECT CERAMIC CHIP ELECT CERAMIC CHIP FILM CERAMIC CHIP MYLAR ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 1500uF 1500uF 1500uF 1500uF 0.001uF 0.1uF 0.1uF 100uF 100uF 1uF 0.01uF 0.01uF 0.01uF 0.001uF 100uF 0.1uF 100uF 0.001uF 1uF 0.1uF 0.047uF 2200uF 2200uF 0.01uF 0.01uF 0.01uF 1uF 1uF 22uF 0.1uF 10% 10% 20% 20% 20% 20% 5% 10% 10% 20% 20% 20% 10% 10% 10% 10% 20% 10% 20% 5% 5% 10% 5% 20% 20% 10% 10% 10% 20% 20% 20% 10% Remark 50V 50V 35V 35V 35V 35V 25V 50V 50V 16V 16V 16V 50V 50V 50V 100V 16V 50V 16V 25V 50V 50V 100V 16V 16V 50V 50V 50V 16V 16V 50V 50V Ref. No. D803 D804 D805 D806 D807 D901 D902 D904 D905 D906 D907 Part No. 6-501-466-01 6-501-467-01 8-719-025-50 8-719-025-50 8-719-801-78 8-719-801-78 8-719-801-78 8-719-025-50 8-719-801-78 8-719-801-78 Description DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE F1B2CCI F1B2CAI 02CZ16-TE85L 02CZ16-TE85L 1SS184 1SS184 1SS184 02CZ16-TE85L 1SS184 1SS184 Remark

8-719-801-78 DIODE 1SS184 < FUSE >

0 F901 0 F902

1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A) 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A) < IC >

IC801 IC802 IC803 IC804 IC805 IC806 IC902 IC903

8-759-745-64 8-759-745-64 8-759-745-64 8-759-745-64 8-759-745-64

IC IC IC IC IC

NJM4560M NJM4560M NJM4560M NJM4560M NJM4560M

8-759-745-64 IC NJM4560M 6-600-354-01 IC PC-17K1 8-759-144-88 IC uPC494GS < JUMPER RESISTOR >

1-126-965-11 ELECT 1-115-339-11 CERAMIC CHIP < CONNECTOR >

JR1 JR2 JR3 JR4 JR5 JR6

1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11

SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP

0 0 0 0 0 0

1-216-296-11 SHORT CHIP < COIL >

CN901

1-580-283-11 PIN, CONNECTOR (PC BOARD) 8P (HIGH LEVEL INPUT/SENSING POWER ON) < JACK > L801 L901

1-410-396-71 INDUCTOR, FERRITE BEAD 0.45uH 1-411-756-11 COIL, CHOKE 50uH < DIODE >

CN902

1-779-078-32 JACK, PIN 4P (INPUT FRONT/REAR) < TERMINAL BOARD >

LED901 8-719-064-11 LED SPR-325MVW (POWER/PROTECTOR) < TRANSISTOR > Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q201 Q202 Q203 6-550-686-01 6-551-504-01 6-551-505-01 6-551-508-01 8-729-045-02 8-729-041-66 8-729-034-50 6-550-693-01 6-550-690-01 6-551-502-01 6-551-503-01 8-729-034-51 6-550-686-01 6-551-504-01 6-551-505-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC2875-B-RTK KTA501U KTC601U KTA1268 KTC3200GR-AT 2SC4015TV2 KTA1504 KTC4373 KTA1661 KTD998 KTB778 KTC3875 KTC2875-B-RTK KTA501U KTC601U

CN903 CN904 CN905

1-780-406-11 TERMINAL BOARD (4P) (FRONT SPEAKER OUT) 1-780-406-11 TERMINAL BOARD (4P) (REAR SPEAKER OUT) 1-780-351-11 TERMINAL BOARD (3P+FUSE) (GND,+12V,REM,25A,25A) < DIODE >

D101 D102 D201 D202 D301 D302 D401 D402 D801 D802

8-719-801-78 8-719-801-78 8-719-801-78 8-719-801-78 8-719-801-78 8-719-801-78 8-719-801-78 8-719-801-78 8-719-025-34 8-719-801-78

DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE

1SS184 1SS184 1SS184 1SS184 1SS184 1SS184 1SS184 1SS184 02CZ6.8-TE85L 1SS184

18

XM-554ZR
AMP
Ref. No. Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q211 Q212 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q311 Q312 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q410 Q411 Q412 Q802 Q803 Q804 Q805 Q806 Q807 Q808 Q809 Q810 Q811 Q812 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 Part No. 6-551-508-01 8-729-045-02 8-729-041-66 8-729-034-50 6-550-693-01 6-550-690-01 6-551-502-01 6-551-503-01 8-729-034-51 6-550-686-01 6-551-504-01 6-551-505-01 6-551-508-01 8-729-045-02 8-729-041-66 8-729-034-50 6-550-693-01 6-550-690-01 6-551-502-01 6-551-503-01 8-729-034-51 6-550-686-01 6-551-504-01 6-551-505-01 6-551-508-01 8-729-045-02 8-729-041-66 8-729-034-50 6-550-693-01 6-550-690-01 6-551-502-01 6-551-503-01 8-729-034-51 8-729-034-51 8-729-034-51 8-729-034-51 8-729-034-51 8-729-034-51 6-551-511-01 6-551-510-01 8-729-038-54 8-729-038-54 8-729-038-54 8-729-038-54 8-729-038-67 8-729-038-54 8-729-038-67 8-729-034-51 8-729-040-76 8-729-034-51 8-729-038-67 6-551-507-01 6-551-507-01 6-551-506-01 6-551-506-01 Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTA1268 KTC3200GR-AT 2SC4015TV2 KTA1504 KTC4373 KTA1661 KTD998 KTB778 KTC3875 KTC2875-B-RTK KTA501U KTC601U KTA1268 KTC3200GR-AT 2SC4015TV2 KTA1504 KTC4373 KTA1661 KTD998 KTB778 KTC3875 KTC2875-B-RTK KTA501U KTC601U KTA1268 KTC3200GR-AT 2SC4015TV2 KTA1504 KTC4373 KTA1661 KTD998 KTB778 KTC3875 KTC3875 KTC3875 KTC3875 KTC3875 KTC3875 KTD2424 KTB1424 KRA102S KRA102S KRA102S KRA102S KRC102S KRA102S KRC102S KTC3875 KTA1273-Y-AT KTC3875 Remark Ref. No. Q915 Part No. Description Remark

8-729-034-50 TRANSISTOR KTA1504 < RESISTOR >

R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R112 R113 R114 R151 R152 R153 R154 R155 R156 R157 R158 R159 R160 R161 R162 R163 R164 R165 R166 R167 R168 R169 R170 R171 R172 R173 R174 R175 R176 R177 R178 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R213

1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-875-11 1-216-840-11 1-216-833-11 1-216-833-11 1-218-843-11 1-216-833-11 1-216-837-11 1-216-222-00 1-216-841-11 1-216-825-11 1-216-218-11 1-218-883-11 1-218-883-11 1-218-851-11 1-218-851-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-218-843-11 1-216-813-11 1-216-833-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-216-833-11 1-218-893-11 1-249-385-11 1-216-837-11 1-216-837-11 1-218-851-11 1-218-851-11 1-218-875-11 1-216-833-11 1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-875-11 1-216-840-11 1-216-833-11 1-216-833-11 1-218-843-11 1-216-833-11

RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP

2.2K 22K 22K 220K 220K 15K 15K 15K 39K 10K 10K 680 10K 22K 10K 47K 2.2K 6.8K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220 10K 220

5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 0.5% 5% 5% 5%

1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W

RES-CHIP 2.2 5% 1/8W RES-CHIP 2.2 5% 1/8W ENCAPSULATED COMPONENT 0.1X2 5W METAL CHIP 10K 5% 1/10W METAL CHIP 82K 0.5% 1/10W CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2 22K 22K 1.5K 1.5K 15K 10K 2.2K 22K 22K 220K 220K 15K 15K 15K 39K 10K 10K 680 10K 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 5% 0.5% 5% 1/4W F 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W

TRANSISTOR KRC102S TRANSISTOR MMBTA06 TRANSISTOR MMBTA06 FET IRFI3205 FET IRFI3205

6-551-506-01 FET IRFI3205 6-551-506-01 FET IRFI3205 8-729-034-51 TRANSISTOR KTC3875

19

XM-554ZR
AMP
Ref. No. R214 R251 R252 R253 R254 R255 R256 R257 R258 R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R269 R270 R271 R272 R273 R274 R275 R276 R277 R278 R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R314 R351 R352 R353 R354 R355 R356 R357 R358 R359 R360 R361 R362 R363 R364 R365 Part No. 1-216-837-11 1-216-222-00 1-216-841-11 1-216-825-11 1-216-218-11 1-218-883-11 1-218-883-11 1-218-851-11 1-218-851-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-218-843-11 1-216-813-11 1-216-833-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-216-833-11 1-218-893-11 1-249-385-11 1-216-837-11 1-216-837-11 1-218-851-11 1-218-851-11 1-218-875-11 1-216-833-11 1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-853-11 1-216-833-11 1-216-833-11 1-218-853-11 1-218-843-11 1-216-833-11 1-216-837-11 1-216-222-00 1-216-841-11 1-216-825-11 1-216-218-11 1-218-883-11 1-218-883-11 1-218-851-11 1-218-851-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 Description METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 10K 47K 2.2K 6.8K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 0.5% 5% Remark 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W Ref. No. R366 R367 R368 R369 R370 R371 R372 R373 R374 R375 R376 R377 R378 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R451 R452 R453 R454 R455 R456 R457 R458 R459 R460 R461 R462 R463 R464 R465 R466 R467 R468 R469 R470 R471 R472 R473 R474 R475 R476 R477 R478 R801 R802 R803 Part No. 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-216-833-11 1-218-893-11 1-249-385-11 1-216-837-11 1-216-837-11 1-218-851-11 1-218-851-11 1-218-875-11 1-216-833-11 1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-853-11 1-216-833-11 1-216-833-11 1-218-853-11 1-218-843-11 1-216-833-11 1-216-837-11 1-216-222-00 1-216-841-11 1-216-825-11 1-216-218-11 1-218-883-11 1-218-883-11 1-218-851-11 1-218-851-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-218-843-11 1-216-813-11 1-216-833-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-216-833-11 1-218-893-11 1-249-385-11 1-216-837-11 1-216-837-11 1-218-851-11 1-218-851-11 1-218-875-11 1-216-833-11 Description Remark

RES-CHIP 220 5% 1/8W RES-CHIP 2.2 5% 1/8W RES-CHIP 2.2 5% 1/8W ENCAPSULATED COMPONENT 0.1X2 5W METAL CHIP 10K 5% 1/10W METAL CHIP CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 82K 2.2 22K 22K 1.5K 1.5K 15K 10K 2.2K 22K 22K 220K 220K 15K 15K 1.8K 10K 10K 1.8K 680 10K 22K 10K 47K 2.2K 6.8K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220 10K 220 2.2 2.2 0.5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5% 1/10W 1/4W F 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W

METAL CHIP 10K 5% 1/10W RES-CHIP 220 5% 1/8W RES-CHIP 2.2 5% 1/8W RES-CHIP 2.2 5% 1/8W ENCAPSULATED COMPONENT 0.1X2 5W METAL CHIP METAL CHIP CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 82K 2.2 22K 22K 1.5K 1.5K 15K 10K 2.2K 22K 22K 220K 220K 15K 15K 1.8K 10K 10K 1.8K 680 10K 22K 10K 47K 2.2K 6.8K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220 10K 5% 0.5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/4W F 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W

ENCAPSULATED COMPONENT 0.1X2 5W METAL CHIP 10K 5% 1/10W METAL CHIP 82K 0.5% 1/10W CARBON 2.2 5% 1/4W F METAL CHIP 22K 5% 1/10W METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 1.5K 1.5K 15K 10K 1K 2.2K 1K 5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W

1-218-843-11 METAL CHIP 1-216-813-11 METAL CHIP 1-216-833-11 METAL CHIP

1-216-198-11 RES-CHIP 1-216-206-00 RES-CHIP 1-216-198-11 RES-CHIP

20

XM-554ZR
Ver. 1.1 AMP
Ref. No. R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R901 R902 R903 R904 R905 R906 R907 R908 R909 R910 R911 R912 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R928 R929 R930 R931 R932 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R944 Part No. 1-216-198-11 1-216-206-00 1-220-397-11 1-216-841-11 1-218-893-11 1-216-833-11 1-216-821-11 1-216-821-11 1-216-837-11 1-216-837-11 1-216-210-00 1-216-210-00 1-220-397-11 1-220-397-11 1-220-397-11 1-216-829-11 1-216-829-11 1-216-841-11 1-216-817-11 1-216-821-11 1-218-875-11 1-218-845-11 1-218-845-11 1-218-843-11 1-218-867-11 1-216-837-11 1-216-845-11 1-218-857-11 1-218-833-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-222-00 1-216-190-00 1-216-190-00 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-170-00 1-216-170-00 1-216-789-11 1-216-789-11 1-216-789-11 1-216-789-11 1-216-150-11 1-216-150-11 1-216-206-00 1-216-833-11 1-216-833-11 1-216-821-11 1-216-829-11 1-216-837-11 1-216-825-11 1-216-829-11 Description RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 2.2K 4.7M 47K 82K 10K 1K 1K 22K 22K 3.3K 3.3K 4.7M 4.7M 4.7M 4.7K 4.7K 47K 470 1K 15K 820 820 680 6.8K 22K 100K 2.7K 270 1K 10K 10K 10K 470 470 1K 1K 1K 1K 68 68 2.2 2.2 2.2 2.2 10 10 2.2K 10K 10K 1K 4.7K 22K 2.2K 4.7K 10K 10K 10K 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W Ref. No. R945 R946 R947 Part No. Description 10K 10K 4.7K 5% 5% 5% Remark 1/10W 1/10W 1/10W

1-216-833-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-829-11 METAL CHIP < SWITCH >

SW801 SW802

1-786-960-11 SWITCH, SLIDE (HPF(80Hz) (FRONT)) 1-786-960-11 SWITCH, SLIDE (LPF(80Hz) (REAR)) < TRANSFORMER >

T901

1-443-277-11 TRANSFORMER, DC-DC CONVERTER < THERMISTOR >

TH901 TH902 TH903

1-804-497-21 THERMISTOR, CHIP 1-804-497-21 THERMISTOR, CHIP 1-804-497-21 THERMISTOR, CHIP < VARIABLE RESISTOR >

VR801 1-227-755-11 RES, VAR, CARBON 10KX2 (LEVEL (FRONT)) VR802 1-227-755-11 RES, VAR, CARBON 10KX2 (LEVEL (REAR)) ************************************************************* ACCESSORIES ************ 2-665-131-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH) 2-665-131-21 MANUAL, INSTRUCTION (RUSSIAN,ARABIC) (Canadian,E) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 101 102 103 3-367-410-21 SCREW (DIA. 5X15), TAPPING (MOUNTING SCREW) 1-823-952-11 CORD (WITH CONNECTOR) (HIGH LEVEL INPUT) (0.2m) 2-663-771-01 COVER (POWER)

101
5 15 mm ( 4)

102

103

0.2 m

1-216-833-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-833-11 METAL CHIP

21

XM-554ZR

REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0 1.1 Date 2006. 02 2006. 03 Description of Revision New US and Canadian model addition.

22