Scribd
Upload
29 views

Lecture #11 Metals, Insulators and Semiconductors, Diodes

This document summarizes key concepts about metals, insulators, semiconductors and diodes. It explains that insulators have no free electrons, metals have many free electrons, and semiconductors have a gap between bonding and conduction electron energies. Doping semiconductors with different atoms creates an excess of electrons or holes. Joining P-type and N-type materials forms a diode that allows current to easily flow in one direction.

Uploaded by

Achmad Zaenuri Rajasa
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
29 views

Lecture #11 Metals, Insulators and Semiconductors, Diodes

This document summarizes key concepts about metals, insulators, semiconductors and diodes. It explains that insulators have no free electrons, metals have many free electrons, and semiconductors have a gap between bonding and conduction electron energies. Doping semiconductors with different atoms creates an excess of electrons or holes. Joining P-type and N-type materials forms a diode that allows current to easily flow in one direction.

Uploaded by

Achmad Zaenuri Rajasa
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 24

Lecture #11 Metals, insulators and Semiconductors, Diodes

Reading: Malvino chapter 2 (semiconductors)


9/24/2004 EE 42 fall 2004 lecture 11 1

Energy states
In any material, there are different roles that an electron can play. Electrons can be tightly bond around the core of atoms Electrons can participate in bonding between atoms Electrons can be at higher energies, and free to move
9/24/2004 EE 42 fall 2004 lecture 11 2

Insulators
In an insulator, all of the electrons are either tightly wrapped around the neuclei, or they are locked into bonds between atoms. Since no electrons or ions can move, the material is an insulator. Examples:
Silicon dioxide Plastic glass
9/24/2004 EE 42 fall 2004 lecture 11 3

Metals
In a metal, a very large number of electrons are free to move. This gives metals there ductility and strength, because the sea of electrons binds the material in a distributed way It makes them good conductors of heat It also makes them very good conductors of electricity.
9/24/2004 EE 42 fall 2004 lecture 11 4

Semiconductors
In a semiconductor, there is a gap in the energies that an electron can take, between those of the bonding (valence electrons) and those that can move (conduction electrons) In an intrinsic semiconductor, all of the valence (bonding) states are full of electrons, but no electrons are left to go into the conduction band. So an intrinsic semiconductor is an insulator, but if a few extra electrons are added, they can move freely.
9/24/2004 EE 42 fall 2004 lecture 11 5

Semiconductor (undoped)
All empty

}
All full of electrons
9/24/2004 EE 42 fall 2004 lecture 11

Energy gap

Semiconductor (N type)
A few extra electrons

}
All full of electrons
9/24/2004 EE 42 fall 2004 lecture 11

Energy gap

Doped with Arsenic or Phosphorus atoms, each with one more proton than a silicon atom, each becomes a fixed positive ion, and neutrality means a few extra electrons will be available
7

Semiconductor (p type)
All empty

}
A few empty states
9/24/2004 EE 42 fall 2004 lecture 11

Energy gap

Doped with Boron, Aluminum or Gallium atoms, each with one fewer proton than a silicon atom, each becomes a fixed positive ion, and neutrality means a few extra electrons will be available
8

Column 3 of the periodic table

If we look at column 3 of the periodic table, we can see that these elements are very similar to silicon, except that they have one fewer protonsone less quantum of positive charge.
9/24/2004 EE 42 fall 2004 lecture 11 9

Energy bands
In general, we wont worry about all of the core electrons, and we will just care about electrons which are in the conduction band, or missing electrons in the valence band. Electrons in the conduction band are called wait for this electrons Missing electrons from the valence band are called holes
9/24/2004 EE 42 fall 2004 lecture 11 10

Conduction and valence bands

Electrons Energy gap, about 1 electron volt Holes

9/24/2004

EE 42 fall 2004 lecture 11

11

Recombination
Electrons

Energy gap, about 1 electron volt


Holes

If an electron comes near a hole, it can fall into the open state. This is called recombination. The extra energy can heat up the crystal, or it can be released as light (as in a light emitting diode)

9/24/2004

EE 42 fall 2004 lecture 11

12

Recombination
Electrons

Energy gap, about 1 electron volt


Holes If some energy is available, on of the many electrons in the valence band can jump up into the conduction band, leaving a hole behind. This process is called generation. Of course, this always makes a pair, an electron and a hole. In a solar cell, light causes this jump, and that is how sunlight is converted into electrical energy (we just need to get the electron and hole out before they recombine!)
9/24/2004 EE 42 fall 2004 lecture 11 13

Electrons and Holes


If you were to have both electrons and holes in the crystal, the electrons could fill up the holes until one or the other was depleted. Silicon crystals with quite a few extra electrons running around are called N-type, and they only have a few holes in the valence band. Silicon crystals with many holes running around are called P-type, and they only have a few electrons in the conduction band.
9/24/2004 EE 42 fall 2004 lecture 11 14

Applications
We can take silicon wafers and put patterns of doping on their surface, and control its conductivity. We can further control the conductivity by applying electric fields We can make use of the difference between P and N type carriers moving through the crystal. This ability to control the conduction of silicon is the basis for the function of transistors, the foundation of the entire electronics industry
9/24/2004 EE 42 fall 2004 lecture 11 15

Diodes
If we have a P doped material next to an N doped material, the result is a diode.

Remember: the P type material has extra fixed negative charge


And mobile positive charge (holes)

The N type material has extra fixed postive charge


And mobile negative charge (electrons)
9/24/2004 EE 42 fall 2004 lecture 11 16

Diode
If we apply a voltage to push the electrons and holes toward each other, they can recombine at the junction and a current will flow (this is called forward bias) If we apply a voltage which pulls the electrons and holes away from each other, then the will pull back from the junction, and very little current will flow. (called reverse bias) So a diode acts like a one way valve for current and the symbol is an arrow in the direction that the current is allowed to flow
9/24/2004 EE 42 fall 2004 lecture 11 17

The diode can be used for many purposes, for example to charge a power supply capacitor from an AC source

~
9/24/2004 EE 42 fall 2004 lecture 11 18

IV curve for a diode


The IV curve for a ideal diode is to have zero current in the reverse direction, and no resistance when forward biased
Current

Voltage

9/24/2004

EE 42 fall 2004 lecture 11

19

Unbiased diode
If we were to make an N type material and join it to a P type material, we would have extra electrons right next to holes. Near the joint, the extra electrons and extra holes recombine, leaving a region which has no carriers called the depletion zone) The loss of the mobile charge leaves the fixed charge from the dopants in place, and that creates an electric field which keeps more electrons and holes from wandering into the deletion layer.
9/24/2004 EE 42 fall 2004 lecture 11 20

Depletion zone
+ + + + -- + + + +

+- +

- + + + - -+ + + - +

+ + -

The mobile electrons and holes are held back from the joint by the electric field from the the fixed charges

9/24/2004

EE 42 fall 2004 lecture 11

21

Reverse leakage
In a real diode, if a reverse bias voltage is put on it, a small reverse current flows. This current is called the leakage current It is caused by:
Generation in the depletion zone (at higher temperatures, there is more leakage current, and light on a diode can cause a lot of leakage current) surface and edge effects.

If enough reverse voltage is applied, the diode will break down and conduct a lot of current (not necessarily destructively)
9/24/2004 EE 42 fall 2004 lecture 11 22

Real diode under forward bias


In a real diode, as you reduce the depletion width, pushing the mobile carriers together, the current does not turn on instantly, but rises exponentially with the voltage

9/24/2004

EE 42 fall 2004 lecture 11

23

Real diode IV curve

9/24/2004

EE 42 fall 2004 lecture 11

24

You might also like